plate bending used for sale

Specifications: Working length: 2550 mm Max. bending power: 6.0 mm Bend : 4.0 mm Diameter upper roller: 176 mm Diameter lower roller: 176 mm Control panel with digital display Motor power: 7.5 kW CE mark Dimensions (length x width x height): approx. 4000 x 1400 x 1500 mm Weight: approx. 3.6 tons Note: the machine was used exclusively for straightening coated aluminum sheets Rollers were wrapped in foil, which was removed without leaving any residue Condition of the rollers almost as good as new few operating hours

Specifications: Working width: 1050 mm Max. bending power: 100.0 mm Max. bend: 80.0 mm Diameter upper roller: 530 mm Diameter of side rollers: 530 mm Conical bending device by inclined position of the two side rollers Mobile control panel with digital display Engine power: 37 kW Hydraulic Safety Chucks CE mark Net weight: approx. 16 tons Auxiliary: 2. Roller set : Diameter upper roller: 360 mm Diameter of side rollers: 360 mm

OFFER PLATE ROLL 2000x6 mm SERGI 3ROLL INITIAL PINCH ASYMMETRIC 2050 X6 MM Rolls length 2050 mm -Top roll 170 mm -lower/Side rolls 150 mm -Power electric 5,5 Hp Capacity -plate width 2000 mm -plate thickness 6 mm with prepinch Configuration on the machine -Rollers surface hardened high strength -Central rolls driven electric rotation on gearunit -side roll electric run with prepinch Pinch roll position with handwheel Front open manual drop-end -Readout gauge of side bending roll -Foot-pedal electric rollers rotation back/forth -Joystick electric control of side roll -Safety installations with emergency stop. -Machine in good conditions

4roll plate bending machine 2500 X 12 mm with central support hydraulic for large diameters and side arm plate support Capacity plate width 2500 mm Plate thickness 12 mm Prebend 10 mm Upper roll 265 mm Lower rolls 245 mm Surface useful on rolls 2550 mm Power supply 380/50 Electric motor 15 Kw on hydraulic unit Configuration Hardened rolls very high surface resistance Conical bending attachment Digital position readout of the rollers Safety and emergency installed per norms Hydraulic rolls power driven with planetary gear unit Hydraulic motion of rollers individual with dual initial pre-pinch Open front drop-end hydraulic to unload the closed shells Central support vertical hydraulic operated for large diameters Side arm operated hydraulic support Total weight of the machine 7500 Kg Total weight of the machine 7500 Kg machine layout 4200X15 ...

Key data: 3000 mm, 8 mm

3-roll bending machine / round roller Schäfer SRMVHY – fully functional For sale is a used 3-roll bending machine (round roller / sheet metal bending machine) from the manufacturer Schäfer, model SRMVHY, built in 1992. The machine is in fully functional condition and is ready for immediate use. The rollers are hydraulically adjustable, which allows for precise and comfortable adjustment. The round bending machine is ideal for bending sheet metal in workshops and production plants. Technical data: Manufacturer: Schäfer Model No.: SRMVHY Year of Make: 1992 Max. sheet width: 3,000 mm Max. sheet thickness (mild steel): 8 mm Roller diameter: approx. 200 mm Voltage: 380 V Dimensions (L x W x H): approx. 5,300 x 1,800 x 1,300 mm Condition: used, fully functional Equipment: hydraulically adjustable rollers Changes and errors in the technical data, ...

4 ROLL HYDRAULIC DUAL PRE-PINCH 3000x15 MM PLATE BENDING MACHINE NEW Brand MG model M3015 -Width of plate 3000 mm -Thickness of plate rolling 15 mm -Thickness of plate pre-bend 12 mm minimum bending diameter ID 350 mm Rolls dimensions: -Surface length mm. 3100 -Top roll mm. 290 -pinch roll mm. 270 -Power electric 10 Hp Technical data: -rolls hardened surface high resistance -variable rolling speed -Powered driven hydraulic rolls rotation -conical bending attachment roller type -calibration system re-rolling welded shells -deflection pinch pressure adjustable upon the thickness -overload protect complete safe operation of the machine. -control console on wheels with electric joysticks commands -position readout digital display for rolling memorize and repeat -safety and emergency systems installed -manuals and schematics along with the machine

used chamber filter records 1000 x 1000 PP approx. 190 pieces in the camp

Krings Verbau various base plates with mounting plate dimensions, spindles, etc. in the package or individually for sale Mass and guide can be requested to e-mail Price VB

Straightening plate measuring plate measuring plate reinforced plate made of steel casting used. Length approx. 3560 mm Width approx. 985 mm Height approx. 910 mm (adjustable) with 5 feet Casting tear ingenuous plate with height-nivelable feet, support ball-bearing Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.

max. plate width: 80 cm stamp width: 425 mm serial no.: 174 plate punch autoplate The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 80 cm stamp width: 425 mm serial no.: 564 plate punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 55 cm stamp width: 220 mm serial no.: 10101/09 plate clamping system: autoplate plate punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 55 cm stamp width: 220 mm serial no.: 10101/09 weight: 12 kg dimensions of press (L x W x H): 70 x 13 x 55 cm plate clamping system: Autoplate for QM 46 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 80 cm stamp width: 425 mm serial no.: 1132 Plate punch for Heidelberg S-Offset The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 80 cm stamp width: 425 mm serial no.: 5136 Plate punch for Heidelberg S-Offset The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 52 cm stamp width: 220 mm serial no.: 16548 plate punch for GTO or QM 46 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 50 cm stamp width: 220 mm serial no.: 4184/20 Dimensions (L/W/H): 60x20x50 mm plate punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 920 cm stamp width: 425 cm Dimensions (L/W/H): 550/1000/1220 cm plate punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 74 cm stamp width: 340 mm serial no.: 13434 dimensions of press (L x W x H): 80 x 95 x 120 cm weight: 100 kg Thermo plate bender for The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 52 cm stamp width: 220 mm serial no.: 3851/15 Dimensions (L/W/H): 60x20x50 mm plate punch QM 46 or GTO The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. plate width: 1520 cm stamp width: 780 mm dimensions of press (L x W x H): 150 x 58 x 128 cm plate punch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

stamp width: 425 mm serial no.: 6660/39 Dimensions (L,W): 71 x 55 cm plate punch for SM 52 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Base plate, turntable, machine vice -Base plate with angle scale -Dimensions: see photos -Dimensions total: Ø 395 x 50 mm -Weight: 18.6 kg

Granite measuring plate on base plate plate size approx. 1,000x800x170 mm, without the contents on the table

Baking Plate / Stone Plate / Oven Plate for Miwe Condo 1225x815x13mm NEWBack Plate / Stone Plate for Miwe Condo Oven Dimensions : 1225 mm x 815 mm x 13 mm Thickness 13mm Weight 25kgwe have other size and assortment in stock Details see pictureAttention: No shipping only pickup. Shipping by forwarding agent from 10 pieces on request 

Baking plate / stone plate / oven plate for quail Piccolo 600x865x15mm NEWBack plate / stone plate for quail Piccolo oven dimensions: 600 mm x 865 mm x 15 mm thickness 15mm Weight 16kgwe have other size and assortment in stock Details see pictureAttention: No shipping only pickup. Shipping by forwarding company from 10 pieces on request

For an injection moulding machine, hole diameter 125 mm Auction-ID: A1-43992-210

see photos

Tool cabinet for press brake Good for AMADA / PROMECAM or Type A L / W / H: 1050 mm x W 850 mm / H 1240mm, 310kg -extendable drawers, allowing access from both sides of the tools -any height adjustment of shelves -sturdy steel construction Fork-lateral guide rails for transporting by forklift (cavity under the cabinet) -The drawers run on Rollengleitschienen (serve as additional stabilization) , the cabinet can be broken - Number of drawers: 4 pieces - Dimensions of a drawer: - 1200mm Overall height / Overall width 850mm / 1050mm Overall depth - Dimensions of the compartments in a drawer: - Fachhhoehe set to 210mm (is varriabel) - Total compartment height 990mm shelves available ohnen - Usable shelf width 130mm - Usable shelf depth 980mm - Number of shelves: 3 piece

Tool cabinet for press brake Good for AMADA / PROMECAM or Type A L / W / H: 1050 mm x W 850 mm / H 1240mm, 310kg -extendable drawers, allowing access from both sides of the tools -any height adjustment of shelves -sturdy steel construction Fork-lateral guide rails for transporting by forklift (cavity under the cabinet) -The drawers run on Rollengleitschienen (serve as additional stabilization) , the cabinet can be broken - Number of drawers: 4 pieces - Dimensions of a drawer: - 1200mm Overall height / Overall width 850mm / 1050mm Overall depth - Dimensions of the compartments in a drawer: - Fachhhoehe set to 210mm (is varriabel) - Total compartment height 990mm shelves available ohnen - Usable shelf width 130mm - Usable shelf depth 980mm - Number of shelves: 3 piece

Working width: 1050 mm sheet thickness: 1.5 mm top rollers Ø: 70 mm bottom rollers Ø: 70 mm weight: 320 kg space requirement: 700 x 1300 x 1100 mm

hydraulic concrete steel Benders Krupp Futura B 703 steel bending machine with accessories and complete instructions Tech. Data performance table - steel 50-55 kp/mm2 Diameter 22 mm - 6 bars per bending, 28 mm-4, 32 mm 3,. Mtfgtw 50 mm 2 speed 4-12 / min Operation - with control or manual, operating dial - HAND - machine with possibility of 3 bending angle set - every page - 3 links + 3 right complete documentation, operating instructions much accessories more info upon request You can edit, flat, round steel accessories - various bending rollers, bolts, reducing roll, Overarm and the machine has device for Pipes. Bulk 2.3 x 1 x 1 m, Btto 1500 kg

Max pipe Ø: 60,3 x 3.2 mm maximum bending angle: 180 ° PIN length: 3000 mm Electr. Supply: 380 V, 8.6 kW space: 2400 x 5700 x 1500 mm weight: approx. 2500 kg

Hydraulic press brake, used Hydraulical press brake, used type / model: D 160-25 Make / make: GWF Year / year of make: 1993 Pressure / force: 160 t Bending length / working length: 3,050 mm Stand width approx. / distance b/n standards: 2.550 mm Table width: 220 mm Stand RADIUS / depth of Cap: 280 mm height / shut height: 440 mm working stroke ca / stroke. Max 250 mm Hubgeschw. / speed of stroke: down: down; 90 mm / s Press down 11 mm / s Expensed. / upward: 90 mm / s Machine weight / weight: approx. 13 t Power consumption / connected load: 22 kW Spec/specif.: 2-hand/foot control / 2 foot switch - manual

Bending capacity: Copper or brass tube: 54 x 4 mm Steel tube: 54 x 2 mm Stainless steel pipe AISI 304/316: 42 x 3 mm Hydraulic tube ST35: 54 x 4 mm Furniture construction tube: 54 x 3 mm Aluminium tube: 54 x 5 mm Gas pipe for piping: 1 1/2 " Maximum bending angle: 210° Engine power: 1,1 kW Voltage: 400 V Machine dimensions (W x D x H) without stand: 800 x 300 x 680 mm Approximate weight: 107 kg Scope of delivery: Bending segment 1/4 "G (Ø 13.72 mm) incl. counter rollers and race Bending segment 1/2 "G (Ø 21.3 mm) incl. counter rollers and race Bending segment 1 "G (Ø 33,7 mm) incl. counter rollers and race Bending segment 1 1/4 "G (Ø 42.25 mm) incl. counter rollers and race

The CNC press brake SMD PBH 110-3100-4C produced in 2006 is offered in a set with the ANTIL TWISTER F5 robot. Technical parameters : - manufacturer: SMD - type: PBH 110-3100-4C - year of production: 2006 - control: CNC CYBELEC ModEva 10 - overworked time: about 20,000 man-hours - pressure force: 110 tons - bending width: 3100 mm - maximum working speed: 10 mm / s - table width: 60 mm - table height: 960 mm - stroke: 465 mm - frame spacing: 2600 mm - throat: 410 mm - power supply: electric - 11.5 KW, 400 V three phases - oil tank capacity: 250 l - dimensions of the press: 3960 × 2045 × 3650 mm - total weight: 9500 kg Processing on a 3 m table and palletizing of finished details on 3 europallets.

Roll length: 1250 mm max sheet thickness: 1.25 mm Roll diameter: 60 mm Length: 1780 mm Depth: 550 mm Height: 1030 mm Weight: approx. 230 kg

For sale we offer a bending machine. It is a Demonstration machine used for prototypes in our production department. Therefore, a few operating hours of approx. 154.1 Bh technical data: Bending force: 40T Bending length: 1600mm Distance between columns: 1200mm Stroke (Y-axis): 150mm Open height: 390mm Table width: 120mm Working speed: 15mm/s Fast speed: 150mm/s Return speed (up): 100mm/s Control axis (8 + 1 axis): Z1,Z2, Z1, Z2, R1, R2+V Power: 5.5 kW Control - Delem-DA-66T (Multilingual) Operating Instructions: English Number of strokes: 10645 Price net: 35.000â?¬ Visit possible by prior arrangement. If you are interested, please contact us.

Technical data: 4 bending rolls Max bending range: 3,000 mm external switching and Control Panel, as well as counter holder

specifications: Max sheet width 3,000 mm Max sheet thickness at max yield strength 240 N/mm2 when bending to max. sheet width 35 mm when rounding Bend length 2.2 x S Max passage between rollers 145 mm Roller diameter upper roller 552 mm Underroller 532.4 mm Side rollers 400 mm Number of rollers 4 Powered rollers 2 top and bottom roller Drive of the rollers hydraulically Arrangement of the rollers symmetrically Rotation speed of the rollers 2-4 m/min Adjustable rollers 3 Type of adjustment of the rollers hydraulically Adjustment speed lower roller 0-200 mm/min. Side rollers 0-700 mm/min. Brake of the rollers pneumatic Actuation of the folding bearing hydraulically Operating voltage 3 x 380 V / 50 Hz Display device of the roll positions 4 x optical/analog Weight of the machine approx. 42 to Area 2.71 x 6.4 m Height 3.12 m

Bending length: 1070 mm Bending capacity: 3.0 mm Reel diameter: 95 mm Roller speed: 9 RPM Engine power: 1,1 kW Weight: 370 kg Dimensions: 1350 x 760 x 1250 mm

Tool cabinet for press brake Good for WILA / TRUMPF tools or Type B L / W / H: 1180 mm x W 850 mm / H 1200mm, 350kg -ausziehbare drawers, allows the double-sided access to the tools -beliebige height adjustment of shelves -robust steel construction, powder coated -Lateral fork guide rails for transporting by forklift (cavity under the cabinet) -The drawers run on Rollengleitschienen (serve as additional stabilization) -The cabinet can be dismantled - Number of drawers: 4 pieces - Dimensions of drawer: - Total height 1200mm / 850mm total width / total depth 1180mm - Dimensions of the compartments in a drawer: - Fachhhoehe adjusted to 210mm (is varriabel) - Trade Height total usable ohnen shelves 990mm - Trade width 130mm available - Trade depth usable 1100mm - Number of shelves: 4 pieces / completely continuous; "ready for operation"

Max bending length: 1020 mm Max. sheet metal rod: 2 mm steel motor upper cheek adjustment via foot switch manual rear stop diverse bending rails

Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßer CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßerb CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

Punching and forming center in chain with an assembly line for the production of relays, see pictures

Machine number: ST-R-1660 Buerstentgratmaschine for the deburring of metal sheets or plates Power supply: 380 V 50 Hz 1.0/1.4 kW 2 speeds: 1500-3000 rpm. Brush diameter: 250 mm

Working width: 1040 mm sheet thickness: 1.25 mm sheet thickness in bending: top rollers diameter: 56 mm bottom rollers diameter: 56 mm weight: 190 kg space requirement: 1450 x 460 x 1030 mm

Technical data: -maximum working length 1250 mm -Stand round 1050 mm -Max pressing force 80 t -Stroke 250 mm -Stand RADIUS 300 mm -Max height betw. Table - press bar 560 mm -Lifting speeds -Backward speed idle max 100 mm / sec. -Forward speed 100 mm / sec. -Backward press speed max. 12 mm / sec. -Total power 15 kW -Space requirement approx. B 1750 x H 3400 X 2000 mm -Weight approx. 8500 kg -with: - CNC - control CYBELEC DNC 7400 PSGY -controlled X - axis back gauge 5-1000 mm -Pneum. Z - axis in three stages. height-adjustable -manually movable and foldable stop fingers -controlled pneumatic die shift - hydr. Tool clamping -Manual crowning - 2 piece support arms -Pointed tool shared H 320 x L 1000 mm -Foot tool H 320 mm x L 1000 mm - universal matrix L 1000 mm