We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
119,105 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
Shaft diameter: 45mm Top roller hydraulically adjustable 3 driven rollers Digital reading
new
sheet width: 2000 mm plate thickness: 35 mm pre-bending: 30 mn number of rolls: 4 Walzen diameter of upper rolls: 400 mm roll diam. bottom roll: 300 mm speed: 1,5 - 5 m/min total power requirement: 38,5 kW weight of the machine ca.: 16,5 t dimensions of the machine ca.: 4,95 x 2,45 x 2,3 m Basic equipment: - Conical bending device - Swiveling top roller - Electrically adjustable rear roller - Conical bending device - driven top roller - Pre-bending device - brake motor - Safety device emergency leash - CE certified - documentation Options: Digital display for rear roller Hardened rollers 2 driven roller Rolling extension The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
New OSTAS profile roller Type OPK-45 Shaft diameter 50mm Hydraulic top roller adjustment Digital readout Can be used horizontally and vertically
used
The machine is in good technical condition, it is possible to test it by agreement. Parameters: Maximum pipe diameter: 40 mm Maximum pipe wall thickness: 2 mm Total power: 4.6 kW Machine height: 1120 mm Machine length: 4450 mm Machine width: 800 mm Machine weight: 1100 kg
used
Pipe cutting machine Length 2950mm. Width 1670mm. Height 2350mm. Control voltage 24VDC 230VAC. Rated current 32A. Total power 18kW. Weight 3000kg. Noise level 75dB.
used
The hydraulic profile bender PBH 80 is in good technical condition, including a wide range of accessories. Can be seen by appointment.
used
Machine weight: 20500 kg Max. bend length: 5000 (custom extended machine) mm Max. collet diameter: : 102 mm Max. bending capacity:: D 102, Rmax = 400 mm Min. bending inner radius:: 65 mm
Type: PWZ 205/4 Number of rolls: 3 rolls Roll capacity cold: 2050 x 4 mm
used
Salvagnini P4-2525 Automatic Panel Bending Machine Machine is in very good condition Bending height max: 254 mm Bending width max: 2540 mm
used
Manufacturer LOIRE SAFE Model ESSC 300/ 30-20 / 20-15 Year 2003 Press Maximum adjustable force 300 a 3.000 kN Return force 600 kN Max opening between fixed table and chuck 2.000 mm. Mobile chuck travel 1.500 mm. Dimensions of the lower mobile table Fontal 3.000 mm. Lateral 2.000 mm. Dimensions of the mobile chuck Frontal 3.000 mm. Lateral 2.000 mm. Machine weight without tools or accessories 63.000 kg. Speeds Approaching speed, without pressure 60 mm/s Working speed, adjustable by potentiometer 1 a 7 mm/s Demoulding speed, adjustable by potentiometer 1 a 35 mm/s Return speed 60 mm/s Tooling Dimensions Frontal 3.000 mm. Lateral 2.000 mm. Height 1.500 mm. Max weight Mobile part 18.000 kg Total 42.000 kg Accessories Upper plate with tilt system INCLUDED Movable lower table with tilt system INCLUDED Stop time and safety distance Stop time 123 ms Safety ...
used
Wire bender OMAS CEB 110 BV in excellent condition
used
tube diameter: 25 mm wall strength: 2 mm bending radius min.: 10 mm Control: bending radius max.: 75 mm total power requirement: 11 kW weight of the machine ca.: 1,45 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
The machine is fully functional, with a rich set of tools. Pipe bending tools: fi 83 - R300 fi 88.9 - R300 fi 101.6 - R250, R400 fi108 - R450 fi 114.3 - R550 fi 133 - R400 fi 137 - R500 fi 168 - R700 fi 193 - R600 fi 219 - R640, R800
used
This HACO PPV 30220 Bending machine was manufactured in the year 2007 in Belgium. It is equipped with a HACO ATL 550 control unit. The machine has a pressing force of 2200 kN and a bending length of 3000 mm.
used
used
This Trumpf TrumaBend V85S Bending machine was manufactured in the year 2003 in Austria. It is equipped with a Trumpf control unit and has 4 axis. The machine has a pressing force of 850 kN and a bending length of 2550 mm.
used
This EHT VarioPress 225-30 Bending machine was manufactured in the year 1997 in the Netherlands.
used
This RAS FLEXIbend 73.40 Bending machine was manufactured in the year 2005 in Germany. It is equipped with a SYSTEM 6000 TOUCH control unit. The machine has a bending length of 4060 mm.
used
This Amada HG-1703 Bending machine was manufactured in the year 2022 in France and has 6700 production hours. It is equipped with an AMADA AMNC3i control unit and has 10 axis. The machine has a pressing force of 1700 kN and bending length of 3110 mm.
used
This Schröder Fasti 145-18/075 Bending machine was manufactured in the year 2008 in Germany.
used
This GASPARINI XP 150/3000 Bending machine was manufactured in the 2008 in Italy. It is equipped with a DELEM DA-69W control unit. It is included with tools. The machine has a problem to starting up. There is an issue with the software, and the control screen is black.
used
This Bystronic Xpert 250/4100 Press Brake Machine was built in the year 2016 in Germany and has 17550 hours. The machine has a pressing force of 2500 kN.
used
This AMADA HFB 125 Bending machine was made in 1999 in France. It is equipped with an Amada Operatour control unit and has 8 axis. The machine has a bending length of 3000 mm.
used
This PIT 63/30SB Bending machine was manufactured in 2002 in Romania. This machine has a pressure of 630 kN. Was installed with a 5.5 kW power.
used
This KOMAGE S 50 4E CNC Hydraulic Press was manufactured in the year 2017 in Germany by the Komage Gellner Maschinenfabrik KG. It has a pressing force of 500 kN. The machine is in a very condition as serviced on an annual basis directly by Komage. In total the press has worked for 23,379 production hours and 2,113,050 strokes.
used
This RAS 62.30 TURBObend Plus bending machine was made in the year 2004. It is equipped with a Ras CNC 6000 control unit. The machine has a sheet length of 2540 mm and a max. sheet thickness of 2 mm.
used
This KOMAGE Mechanical Powder Press was manufactured in the year 1998 in Germany by the Komage Gellner Maschinenfabrik GmbH. It has a pressing force of 50 kN. The machine is in a good condition for its age as serviced on an annual basis directly by Komage.
used
This Blecken PPE SE-3160 Bending machine was manufactured in the year 2007 in Spain. It is equipped with a Delem ER-70 control unit and has 4 axis. The machine has a pressing force of 1600 kN and a bending length of 3100 mm.
used
This Tauring Alfa 200 Tube Bending machine was manufactured in the year 2007 in Italy.
new
sheet width: 3070 mm plate thickness: 5 mm pre-bending: 4 mm diameter of upper rolls: 200 mm min. bending diameter: 300 mm total power requirement: 5,5 KW weight of the machine ca.: 5,1 t dimensions of the machine ca.: 4950 x 1120 x 1380 mm - Bending capacity 3070 x mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
sheet width: 2500 mm plate thickness: 25 mm pre-bending: 20 mn number of rolls: 4 Walzen diameter of upper rolls: 380 mm roll diam. bottom roll: 300 mm speed: 1,5 - 5 m/min total power requirement: 31,5 kW weight of the machine ca.: 17,6 t dimensions of the machine ca.: 5,45 x 2,3 x 2,45 m Basic equipment: - Conical bending device - Swiveling top roller - Electrically adjustable rear roller - Conical bending device - driven top roller - Pre-bending device - brake motor - Safety device emergency leash - CE certified - documentation Options: Digital display for rear roller Hardened rollers 2 driven roller Rolling extension The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
This TRUMPF TRUMABEND V85S Bending machine was manufactured in 1995 in Germany and has 51193 hours. It is equipped with a Trumpf TrumaBend control unit. The machine does not start, and probably the control system is broken.
used
This ERMAKSAN AP 2100-35 Bending machine was manufactured in the year 2005 in Turkey. The machine has a pressing force of 350 kN.
new
sheet width: 3000 mm plate thickness: 6 mm pre-bending: 4 mn number of rolls: 4 Walzen diameter of upper rolls: 220 mm roll diam. bottom roll: 180 mm speed: 5,0 m/min total power requirement: 7,0 kW weight of the machine ca.: 6,2 t dimensions of the machine ca.: 5,05 x 1,47 x 1,55 m Basic equipment: - Conical bending device - Swiveling top roller - Electrically adjustable rear roller - Conical bending device - driven top roller - Pre-bending device - brake motor - Safety device emergency leash - CE certified - documentation Options: Digital display for rear roller Hardened rollers 2 driven roller Rolling extension The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
sheet width: 2000 mm plate thickness: 50 mm pre-bending: 45 mn number of rolls: 4 Walzen diameter of upper rolls: 550 mm roll diam. bottom roll: 450 mm speed: 1 - 4 m/min total power requirement: 66 kW weight of the machine ca.: 40,00 t dimensions of the machine ca.: 5,75 x 2,95 x 3,05 m Basic equipment: - Conical bending device - Swiveling top roller - Electrically adjustable rear roller - Conical bending device - driven top roller - Pre-bending device - brake motor - Safety device emergency leash - CE certified - documentation Options: Digital display for rear roller Hardened rollers 2 driven roller Rolling extension The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
This ERMAK CNCHAP 3600x200 Bending machine was manufactured in the year 2005 in Turkiye. It is equipped with a CYBELEC DNC 60 control unit. The machine has a pressing force of 2000 kN and a bending length of 3600 mm.
used
This Ermaksan AP 3100-120 Bending machine was made in 2002 in Turkey. The machine has a pressing force of 1200 kN.
used
This BYSTRONIC Xpert 200 x 3100 Bending machines machine was manufactured in 2011 in Germany. The machine has a bending length of 3100 mm and includes a box of bending tools.
used
This Beyeler PR6 Bending machine was manufactured in the year 1997. It is equipped with a DNC 800 control unit. The machine has a pressing force of 1000 kN and a bending length of 3100 mm.
new
sheet width: 1270 mm plate thickness: 1,5 mm bending angle max.: 135 ° : 50 mm weight of the machine ca.: 477 kg dimensions of the machine ca.: 1700 x 730 x 1335 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
sheet width: 1050 mm plate thickness: 1,25 mm bending angle max.: 135 ° : 40 mm weight of the machine ca.: 74 kg dimensions of the machine ca.: 1260 x 500 x 940 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
sheet width: 2570 mm plate thickness: 7 mm pre-bending: 6 mm diameter of upper rolls: 220 mm min. bending diameter: 330 mm total power requirement: 7,7 KW weight of the machine ca.: 5,1 t dimensions of the machine ca.: 4,45 x 1,12 x 1,38 m Basic equipment: - Conical bending device - Swiveling top roller - Electrically adjustable rear roller - Conical bending device - driven top roller - Pre-bending device - brake motor - Safety device emergency leash - CE certified - documentation Options: Digital display for rear roller Hardened rollers 2 driven roller Rolling extension The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
This TECHNOLOGY ITALIANA TP GAMMA SE 2510 Bending machine was made in 2022. The machine has a pressing force of 250 kN. It has still one year of warranty included.
used
This AMADA HFT 50-20 Bending Machine was manufactured in 2009 in France. It has a maximum press force of 500 kN, a maximum stroke of 200 mm and a foreseen power of 6 kW. In total is weighs 4.7 tons. This press brake has operated 11,377 hours so far. Check photo gallery for more details. Contact us anytime for further questions!
new
sheet width: 2070 mm plate thickness: 4 mm pre-bending: 3 mm diameter of upper rolls: 130 mm min. bending diameter: 260 mm total power requirement: 3,3 KW weight of the machine ca.: 1,6 t Basic equipment: - Conical bending device - Swiveling top roller - Electrically adjustable rear roller - Conical bending device - driven top roller - Pre-bending device - brake motor - Safety device emergency leash - CE certified - documentation Options: Digital display for rear roller Hardened rollers 2 driven roller Rolling extension The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
sheet width: 2570 mm plate thickness: 13 mm pre-bending: 10 mm diameter of upper rolls: 280 mm roll diam. bottom roll: 260 mm speed: 5 m/min total power requirement: 7,5 KW weight of the machine ca.: 7,82 t dimensions of the machine ca.: 4,65 x 1,45 x 1,6 mm Basic equipment: - Conical bending device - Swiveling top roller - Electrically adjustable rear roller - Conical bending device - driven top roller - Pre-bending device - brake motor - Safety device emergency leash - CE certified - documentation Options: Digital display for rear roller Hardened rollers 2 driven roller Rolling extension The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
sheet width: 2070 mm plate thickness: 4 mm pre-bending capacity: 3,5 mm diameter of upper rolls: 140 mm total power requirement: 2,2 KW weight of the machine ca.: 1,73 t dimensions of the machine ca.: 3230 x 800 x 1100 mm Basic equipment: - Conical bending device - Swiveling top roller - Conical bending device - driven top roller - Pre-bending device - brake motor - Safety device emergency leash - CE certified - documentation Options: Electrically adjustable rear roller Digital display for rear roller Hardened rollers The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
This AMADA HFT50-20 (2007) Bending machine was manufactured in 2007 in France. It is equipped with a bending force of 50 tons and a bending length of 2085 mm. Distance between uprights is 2665 mm and the vertical stroke at 200 mm. The machine counter shows 8337 hours.
used
This EHT EHPS 25-30 Bending machine was manufactured in the year 1991. The machine has a pressing force of 2500 kN.
used
This STAR-BEND STAR 800 CN6/GEN/L Bending machine was manufactured in the year 2006 in Italy. It is equipped with a STAR-BEND control unit and has 6 axis.