plate bending roll used for sale

Tarzan, Working width 65mm, lever length 740mm. Auction-ID: A1-45188-218

Hand bending machine Flat bar 30 x 8 mm Square steel 12 mm Round steel 15 mm Weight 0.025 t Package size max. 51 x 31 x 22 cm Condition: never used / new (5) Auction-ID: A1-45681-881

Working height: 1035mm, usable width: 6000mm, max. usable length: 6000mm, max. wire diameter: 12mm, max. tensile strength: 650N/mm², bending capacity (number of bars): Ø12mm: 40 bars, Ø10mm: 60 bars, Ø8mm: 90 bars, Ø6mm: 150 bars, Ø5mm: 200 bars, geometry/bending data: smallest leg between two angles: 50mm (with bending finger Ø17mm), standard bending finger: no.60, Ø40mm, number of programmable bending angles: 20, memory positions: 100, speeds: first speed: 45°: max. 5.8s, 90°: max. 8.7s, 180°: max. 13.7s, second speed: 45°: max. 2.9s (complete cycle forward/backward), 90°: max. 4.4s (complete cycle forward/backward), 180°: max. 6.8s (complete cycle forward/backward), mechanics/hydraulics: 4 double-acting hydraulic cylinders, hydraulic unit with pumps, solenoid valves, pressure regulators, safety valves, delivery without oil, operation/control: control panel with keyboard  ...

A Häusler rolling and bending machine is available. Number of rollers: 3, section modulus: 46cm², max. flat material capacity at 1000mm: 100mm/20mm, max. pipe capacity at 900mm: 102mm/6mm, max. square material capacity at 600mm: 60mm/60mm, max. T-profile capacity at 1200mm: 1200mm/1200mm/13mm, shaft diameter range: 125mm-135mm, machine dimensions X/Y/Z: approx. 4500mm/1700mm/1500mm, weight: approx. 6500kg. An on-site inspection is possible.

Offer 24407 Technical data: - 2 motor-driven rollers - Hydraulic. Feed of the upper roll Pressure capacity 18 t - Shaft diameter 60 mm - Shaft rotation 6 rpm - Roller diameter 215 mm - Bending performance - flat steel R 300 upright 80 x 15 mm - R 300 flat 120 x 25 mm - Square R 300 50 mm - Round tube R 900 100 x 2 mm - Drive 400 V / 1.5 kW - with: - separate control panel with digital display + foot switch - right / left – run - Lateral straightening rollers - Standard bending kit for flat and angle material - Weight approx. 1200 kg - Space requirement approx. W 1000 x H 1750 x D 1250 mm

Offer 26001 Technical data: - Horizontal + vertical working position - 3 mot. Driven rollers - hydr. Left lower roller regulation - Hydraulic cylinder pressure capacity 4 t - Shaft diameter 35 mm - Shaft rotation 11 rpm - Roller diameter 132 - 142 mm - Drive 400 V 1.1 kW - Bending capacity approx. - Round tube Ø 800 60 x 1.5 mm - Flat steel Ø 400 90 x 15 mm - Square steel Ø 400 30 mm - With: - Separate control panel with digital display - E – Footswitch in sep. Control panel for right / left run - Standard bending kit for flat and angle material - 6 tube roller sets 22 + 28 + 33 + 42 + 48 + 60 mm - Weight approx. 450 kg - Space requirement approx. W 700 x H 1150 x D 950 mm

Hand bending machine Flat bar max. 16 mm Square steel 16 mm Round steel 16 mm Weight 45 kg Bending angle max. 180 ° Dimensions L x W x H 0.4 x 0.4 x 1.1 m Auction-ID: A7-45761-892

Flat bar bending machine Flat bar 100 x 5 mm Square steel 16 x16 mm Round steel 18 mm Angle steel 100 x 8 mm Dimensions L x W x H 400 x 290 x 280 mm Weight 35 kg Auction-ID: A7-45761-869

Press brake Amada Astro HDS 1030 / NTR BJ 2010

Key data: 170 t

Trumpf Press Brake Trumabend V170, 1700KN, Stroke: 365,. L-530cm, W- 240cm, H-300cm, Weight: 18to,

Machine type: Edge banding machine (single-sided) Manufacturer: BRANDT Model: OPTIMAT KDF 220 C Year of manufacture: 2012 Edge thickness: approx. 0.4 – 6 mm Workpiece thickness: approx. 8 – 60 mm Feed speed: approx. 10 – 11 m/min Control: Electronic control panel (Brandt / HOMAG) Infeed: Manual infeed with driven conveyor chain Edge magazine: Rotary edge magazine (visible) Processing units: - Pre-milling unit - Gluing unit (hot-melt) - End trimming unit - Trimming unit - Radius scraping unit - Buffing unit Extraction: Extraction hood with multiple connections Glue system: Hot-melt glue application Power supply: 400 / 230 V, 3 phase, 50 Hz Fuse protection: 16 A Full load current: 14 A Control voltage: 24 V Machine number: 0-261-09-2410 Remarks: Compact single-sided edge banding machine for straight edges with standard processing units ...

Edge banding machine for sale by purchasing new machine. Machine is currently still in use and still fully operational. It is a very solid machine with return system included. Very stable and always with the right finish! Equipment: Nozzles Format cutters with a diameter of 100mm Blow-off unit Heat unit PUR bonding with warming station for cartridges Pressure rollers 7pcs Hacksaws, straight and angled Brutfmilling top and bottom profile milling radius 1/2mm Scrapers profile/flat Nozzles Brushing brushes -Machine with bottom and top belt (very stable). -Height adjustable at the front (automatic). -Profile milling cutters can be set automatically with program -Cutting saws automatic -everything can be turned on/off via the screen in front -Return options can be operated from the front -------------------------------------------- Manufacturer: HOMAG Model: Optimat kL 77/A20/S2 EVENT Y ...

Machine type: Edge banding machine (single-sided) Manufacturer: BRANDT Model: OPTIMAT KDF 430 C Year of manufacture: 2014 Edge thickness: approx. 0.4 – 8 mm Workpiece thickness: approx. 8 – 60 mm Feed speed: approx. 11 m/min Control: Electronic control system (Brandt / HOMAG control) Processing units: Pre-milling, gluing unit, end trimming, trimming, radius scraping, buffing Glue system: Hot-melt glue unit (EVA / optional PU) Power supply: 400 / 230 V, 3 phase, 50 Hz Fuse protection: 20 A Full load current: 18.5 A Control voltage: 24 V Machine number: 0-261-04-6048 Remarks: One-sided edge banding machine for processing straight edges with automatic edge feeding and post-processing units; suitable for industrial woodworking applications :contentReference[oaicite:0]{index=0} Approx. own mass: 1700 kg Approx. dimensions (LxWxH): 4800 x 1200 x 1600 ...

sheet thickness: 1.25 mm, 400V power supply, additional stones, left and right rotation, speed ​​control, pressure: 40 kp/mm², machine visually refreshed, ready for operation Auction-ID: A7-45896-1

tube diameter:40-90 mm wall strength:20 mm weight of the machine ca.:11 t dimensions of the machine ca.:4 x 1,6 x 1,35 m bending radius max.:270 mm This machine is a mandrel bending machine that was designed exclusively for the production of pipe bends with pipes of 40 mm ? 90 mm outer diameter with a maximum wall thickness of 20 mm or for processing solid materials up to 70 mm outer diameter (max. section modulus 64.7 cm³) and is therefore intended only for this purpose. Scope of delivery, machine equipment, basic equipment ? Pipe length/usable length for mandrel bending: 3000 mm ? Radius range max. 270 mm ? Bending height 1050 mm ? Electro-hydraulic drive ? Clockwise bending direction ? With hollow shaft to achieve small radii ? Counter bearing rotates ? Rotates up to 180 degrees with a maximum tool radius of 270 mm ? Forward movement controlled via hydraulic cylinder with pressure va ...

<br><br><br>Still in operation: Yes<br>Verf Gbar: Immediately

APV K 55 plate apparatus, 6 departments, Y.O.M.1994, late 2005 dismantled, cleaned, new clip seals and plates UV tested. test log exists. Power approx. 960,000 Kcal/h

plate heat exchanger Gea Ahlborn with 2 centrifugal-pumps:(hotwaterpump and recirculationspump) Manufacturer: Gea Ahlborn 6 Sections: preheater 1,preheater 2,heater,precooler 1,cooler,hotwater Type: VT 4 P (1.4401) Fabr.Nr.: 177/4113 flow rate: ca. 750 ltr/h (5 to 72/75°C) - 80 % gain of heat day of construction:1994 weight : ca. 220 kg Dimension : length x width x hight: ca. 103 x 44 x 143 cm

Chamber filter plates PP Polypropylene chamber filter plate -for almost all manufacturers: Rittershaus & Blecher, Passavant, Netzsch, Hoesch, von Roll, Diemme, Filox, Andritz, etc. Cake thicknesses and plate thicknesses are freely selectable depending on the application and filtration conditions. The chamber filter plate made of plastic is characterized by excellent chemical resistance and easy handling due to its low dead weight. - One component - The filter surface consists of a special conical bump structure. This pimpled structure supports the filter cloth and ensures excellent filtration performance for each individual chamber. - Filtratin inputs and filtrate sequences individually according to customer requirements - High plan parallelism, thus flawless sealing in the closed state. Standard formats: 250, 400, 470, 500, 630, 800, 915, 1000, 1067, 1200, 1300, ...

Membrane filter records Standard welds together the filtration cycle can be shortened by the application of membrane filter records considerably, while the unproductive phase of the pressure filtration is broken off and is substituted with the postpressing. full plastic membrane record with welded together membranes, thereby the easiest Handling and the highest chemical permanence perfect separation of the Nachpressmediums of the filtration product variable material choice membrane corners as ? circle to the membrane movement poor in tension for almost all formats and manufacturers. they need spare parts, accessories, service or servicing for your chamber filter press high-pressure membrane pump or drainage facility? request us. we help you with pleasure.

used membrane filter records, membrane chamber filter records 1000 x 1000 pp approx. 190 pieces in the camp

; ready for operation

Length: 350 mm Width: 150 mm Polarity ~ 9 mm Space requirement approx.: L: 440 x W: 210 x H: 135 mm Voltage: 24V Power: 2,04A

Cat. No. 13-0217B-03 in very good condition measurement and weight: 2 plates in stainless steel 60 x 60 HxLxW: 134 x 220 x 97 cm 37 plates in pvc 60 x 60 weight: appr. 850 kg All prices are valid Ex-Works, excl.VAT Freight Charges: depending on dimensions and destination Delivery: from 97753 Karlstadt-Karlburg Subject to prior sale

Chain plates (used) Serial No.: IMA -with rubber plate and mounting bracket -Dimensions: 80 x 60mm -more than 100 PCs available Price per piece: 4,50 euro + VAT

GEA Ahlborn plate heaters used

Cast T-slot plate 1500 x 950 mm

feeder: • pallet feeder • machine number (feeder) 34103/88 • counter EVZ 30 1st folding unit: • pre-slitter shafts • 4 buckle plates • rear-mounted slitter shafts • noise prevention 2nd folding unit: • working width max. 94cm • 4 buckle plates • rear-mounted slitter shafts • noise prevention 3rd folding unit • working width max. 66cm • 2 buckle plates • rear-mounted slitter shafts • noise prevention Still in operation: No Available: sofort

REX - TORWEGGE - HOMAG- BARGSTED - KALFASS - HOMS-410-K core layer production plant (also solid wood boards) Consisting of feeding roller, Package cross-cut saw HOLTEC's 121-SHKA,. more feed roller TRANSA, Rotary scissors type lift roller Solid wood loading portal, Loading system KALFA for planing machine REX, REX planing machine HOMS-410-K built in 2004. with RIP saw unit. Central RIP saw unit, upper and lower drum, Much sheet saw unit, Belt conveyor system 8 manual workstations circular saws, 12 x material import System. 12 x glue system. Glue press TORWEGGE Working length approx. 6600 mm,. 2 cross cutting, 8-speed The stack and cooling system, Stacking line, Conveyor roller conveyor Power 2500 sqm / 7 hours PLATTENAUSBESSERUNGS AND ROLL FORMING LINE BARGSTEDT/HOMAG Plattenausbesserungs line Doppelendprofilier line in TOP condition! Workpiece parameters of ...

Overhauled Plate clamps for Heidelberg Speedmaster SM102 price for 1 set (2 parts) (2 sets for 2 printing units/plates are depicted in the pictures)

Formcook combi grill Belt width: 1100 mm Grill length: 11.000 mm Heating: thermic oil Cooking time: 3-50 min. Maximum temperature of 250 degrees Celsius Power: 25 kW Dimension: 12.825 x 1740 x 2323 mm Weight: 10.000 kg

Plate filter with pump Manufacturer: Rover Pompe Type: Colombo Field of use: Olive oil Filter plates: 25 PCs. End plates: Stainless steel Sheet size: 20 cm x 20 cm Pump: Capacity: 28 l / min Conveying height: 22 m Water temp. Max: 35 ° C In very good condition! Plate filter incl. new replacement filter plates and replacement filters!

2pcs 3500 x 2000 x 350 mm price 7000eur/pc

4 pcs 5600 x 1885 x 400 mm price 10500eur/pc

Working width: 3050 mm sheet thickness: 6 mm throat depth: 200 mm rear gauge: 1000 mm power: 15 kW space: 4100 x 2300 x 2100 mm weight: 8500 kg well-preserved CNC hydraulic shear, with pivoting Panel, serial control. CYBELEC, CNC 1000, Hours of operation according to the operating hour counter: 2700 h

M.- No. : 827

M. No.: 454

U-tronic maximum speed: 250 RPM

1 pcs. length. 3050 mm width 1 pcs. 3050 mm total area of 9 pcs. 83, 72 m²

Plate filters/layers filter on role Manufacturer: KTM Troxler Type: FP 430 30 filter plates made of plastic DN 25 outlet with valve bottom Filter plate size: 40 cm x 40 cm In very good condition!