plastic extruder used for sale

Injection molding machine

R1317 Injection moulding machine ARBURG A 221 - 250 - 55 Year of manufacture 1997 Control Multronica with handling device without hopper and water distributor converted to CF drive but without card, with operating instructions for Arburg and one for the robot Machine was freed up by the purchase of new machines. but no function check from us Price free loaded on truck € 1950.-- +VAT a viewing is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any guarantee for compliance with all requirements mentioned in the UVV (accident prevention regulations).

QUICK WASHER for RIGID and SOFT PLASTICS, made in AISI304 stainless steel, low water consumption, can be used with hot water or mild detergents, for reground LDPE LLDPE HDPE film, rigid PE PP PVC PET PA ABS PS PC, 7,5 kw motor 400V 50/60Hz, inner auger 400 mm diam., length 3.000 mm., material and water are loaded from the bottom, material discharging is done from top, bearings are positioned outside the wet chamber, seals on the lower bearing to exclude any contact with water, auger speed is adjustable to change throughput rate 500 to 1.000 kg/h, throughput rate can be adjusted according to contamination and material, Low water consumption (depending on contamination) About 60 lt., The water can be mechanically filtered with a [water screening system](.germanplast.eu/listings/5003567-germanplast-vibrating-screen- for-water-powder-granule) (available separately) to be reused in the proces ...

AUTOMATIC VERTICAL BINDING BALER, for FILM, WOVEN PP, PET, RIGID AND SOFT PLASTICS, PAPER, CARDBOARD and more, 80 Tons ca. pressing force, 45 kw drive, complete with oil heating and cooling systems, proportional pressure flow controller, Bale size LxWxH 1.100x720 mm (adjustable length), feeding hopper size : 1.100 x 1.600 mm., Average throughput rate, - with 30 kg/m3 materials 5-7 Ton/h, - with 50 kg/m3 materials 9-11 Ton/h, - with 120 kg/m3 materials 17-19 Ton/h, 5 vertical-wire binding, Cycle with no material, no twisting : 25 ca, Pre-press flap with 2 x 20 Ton force, Exchangeable bottom plate in hardox in channel and chamber, oil tank capacity 950 lt., Machine weight ca.25.000 kg., General features, common to all balers:, Construction ìn sturdy carbon steel with top EU components., Compact and easy to use, Automatic binding, Fully automatic with adjustable parameters on touch screen  ...

Price 4.900+VAT (claimable)free loading on truck Injection molding machine Locking force 200t Distance between the spars 520 x 520mm Screws D.=50mm = Injection weight in hp 297gr. Machine very well preserved comes from medical equipment manufacturer Dissolution of injection molding department .with operating instructions and 2 discs. Viewing by e-mail appointment is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any liability for compliance with all requirements mentioned in the UVV (accident prevention regulations)

AUTOMATIC VERTICAL BINDING BALER, for FILM, WOVEN PP, PET, RIGID AND SOFT PLASTICS, PAPER, CARDBOARD and more, 100 Tons ca. pressing force, 45 kw drive, complete with oil heating and cooling systems, proportional pressure flow controller, adjustable channel pressure, Bale size LxWxH 1.100x720 mm (adjustable length), Filling hopper size 1.100 x 1.600 mm., Average throughput rate, - with 30 kg/m3 materials 6-8 Ton/h, - with 50 kg/m3 materials 10-12 Ton/h, - with 120 kg/m3 materials 18-20 Ton/h, 5 vertical-wire binding, upper and lower photocells to control material feeding feeding, Cycle with no material, no twisting : 22 ca, Pre-press flap with 2 x 20 Ton force, Exchangeable bottom plate in hardox in channel and chamber, Baler weight ca.27.000 kg., General features, common to all balers:, Construction ìn sturdy carbon steel with top EU components., Compact and easy to use, Automatic bind ...

Recycling plant/recycling plant General information • Plant type: PET sorting and washing system for the production of PET flakes • Manufacturer: STF-Maschinen & Anlagenbau GmbH • Year of construction: 2023 • New value EUR 4,970,000.00 • Market value (at location): EUR 3,052,000.00 • Installed in two connected halls incl. foundations • Plant currently not in operation (standstill since 11/2024) Technical key data • Max. configuration: 2,000 kg/h • Max. achievable output in continuous operation: 600 kg/h • Output in test run with good material: >1,500 kg/h • Energy requirement: 650-680 kWh (without hot washing system) Stages of the procedure 1. Feeding of PET material (pressed bales) 2. Coarse sorting via sieve drum 3. Magnetic separation of metallic impurities 4. 2-stage sensor sorting (materials) 5. Manual sorting via sorting belt 6. Mill and  ...

AUTOMATIC VERTICAL BINDING BALER, for FILM, WOVEN PP, PET, RIGID AND SOFT PLASTICS, PAPER, CARDBOARD and more, 120 Tons ca. pressing force, 90 kw drive, complete with oil heating and cooling, proportional pressure flow controller, Filling hopper 1.100 x 1.600 mm., Bale size LxWxH 1.100x720 mm (adjustable length), Average throughput rate, - with 30 kg/m3 materials 6-8 Ton/h, - with 50 kg/m3 materials 11-13 Ton/h, - with 120 kg/m3 materials 19-22 Ton/h, 5 vertical-wire binding, Cycle with no material, no twisting : 21 ca, Pre-press flap with 2 x 26 Ton force, Exchangeable bottom plate in hardox in channel and chamber, Machine weight ca 28.500 kg, oil tank capacity : 1.500 kg, General features, common to all balers:, Construction ìn sturdy carbon steel with top EU components., Compact and easy to use, Automatic binding, Fully automatic with adjustable parameters on touch screen panel., A M ...

Cardboard Chuck Cutter - Brand: Llorens Planas - Model: CORE SLIT - Reference: ME-16-2-3 - 1,600 mm - Power: 0.5 hp (0.37 kw) - Year: 2007

Pellet cooler: - Vacuum cleaner: 5.5 kw (7.5 hp) - Electrical panel. -Pipes

Injection moulding machine Engel e-motion 2440/380 T BJ 2008

The scope of delivery includes: 01x Open fronted storage boxes, used Manufacturer: Bito External dimensions: 600 x 400 x 170 mm Interior dimensions: 560 x 360 x 167 mm Opening dimensions: open on one side at the front, 275 x 82 mm (WxH) Handle: yes, single-sided, open Colour: blue Weight | Piece: 1.59 kg General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is associated with additional costs, which will be charged separately depending on the delivery location or scope of delivery.

Special price because without dukumentation / without disc without funnel +VAT (reclaimable) R1277 Injection moulding machine Arburg A 270 Hydronica D-Version Dialogica topZustand screw D 30mm with device for injection into the parting plane a viewing is desirable by appointment Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any liability for compliance with all requirements mentioned in the UVV (accident prevention regulations).

A welding machine Pfaff including a rotary shear Kuris and an unwinding device MK is available. 1) Welding machine Pfaff 8309. 2) Rotary shear Kuris BOM 101. 3) Unwinding device MK Sewing Technology Systems. Documentation available. An on-site inspection is possible. The system is dismantled and ready for loading.

2 x Husky HL500RS80 2016 injection moulding machines

Key data: 850 kN, 40 mm

R1295Injection moulding machine ARBURG 320-850-210 Multronica Screw D=40mm Locking force 85 t.Converted from floppy disk drive to CL drive Viewing by e-mail appointment is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any liability for compliance with all requirements mentioned in the UVV (accident prevention regulations)

Injection moulding machine Krauss Maffei KM 50/90 C2 BJ 2001

2 x Injection Molding Machines Manufacturer. Arburg Type : 270S-250-60 BJ 1996

Year: 2006 technically efficient, ready to work – after full service 3-spindle (high-speed motors) possibility of setting for various profiles (frame / sash) pneumatic profile clamping

Netstal Elion 800 injection moulding machine with Wittmann Handling Primus The machine is fully functional and has only 6500 operating hours

Injection moulding machine Arburg 470C 2000-675 BJ 2007

Injection moulding machine Krauss Maffei KM 300-1900 C2 BJ 2000

Injection moulding machine Arburg 420S 1300-350 BJ 2000 without handling

Injector for Plastics. - 30 mm spindle - Laboratory sample mold - Engine: 10 hp (7.5 kw). - Electrical panel

GAMMAMECCANICA Compac 125 mm. Construction year 1998 Including Loading conveyor belt, Metal detector, Compactor with driven haul off for reels, master dosing unit Engin Plast, Extruder 125 mm diam. 36 L/D with degassing pump d.c. Ansaldo drive 197 kW, Total installed power 501 kW motor, BD plast non-stop screenchanger diam. 200 mm, hydraulic power station, water ring pelletizer M 8500, Electrical cabinet, Type of machine: GAMMAMECCANICA PLASTIC RECYCLING LINE 125 mm.

Year: 2007 - technically efficient, ready to work – after full service - SV 530 cleaning machine - AKS 1610 welding machine - TBA-F 26/25 cooling station - WT 530 turning station - Welding dimensions: 2300 x 3500 mm - Flash limit: 0.2 – 2 mm - Seal formers

Injection moulding machine Demag erg. 250/560 840 BJ 2001

Injection Molding Nose Demag ergotech 50/370-200 BJ 2000

Injection moulding machine Engel victory 200H/200V790 comb BJ 2018

injection molding machine Angel Type: Victory 330/80 Tech Machine No: 155871 Age : 2005

Ideal for operating a business where power outages are not desired, for example injection molding R1334 Power Generator Emergency Power Generator POLYMA/DEUTZ 80 KVA installed in a truck trailer single-axle, was used on construction sites. Dirty outside by leaves and dirt Polyma Kassel 80KVA = 16A = 64 KW,Diesel engine Deutz type F6L912 7ßKW 95hp 2000 rpm., With diesel hand pump hose in canister and pump,With cable/plug 63 A, The trailer is not soundproofed, stood outdoors for years under canopy and is accordingly polluted More detailed pictures on request

Injection moulding machine Krauss Maffei KM 200-1400 C2 BJ 2000

Key data: 20000 kN

Angebot/Offer: Engel Duo 17060/2000 Viper Robot 60 approx. 4900h YOC 2021

URBAN AMS 6010 very good condition fully operational

Key data: 6500 kN, 105 mm

Location is : Latino America !

Key data: 1500 kN, 415 g/PS, 55 mm

Built in 1999 Clamping force: 150 tons. Screw diameter: 55 mm Displacement: 456 cm³ Spray pressure: 1564 bar Very good condition!

Year: 2000 - technically efficient, ready to work – after full service - 4 heads - support arms

Year: 2006 - technically efficient, ready to work – after full service - possibility of mounting 3 milling heads - top and bottom chiseling - control via PLC - automatic machining process

PLASTIC WASHING. LINE for GRAVIMETRICAL SEPARATION, including:, collection hopper, auger, STAINLES STEEL GRAVIMETRICAL SEPARATION TANK, size mm.5.800 x 1.600 ca, n.4 moving rolls, sinking screw, drained screw for collection of floating material, n.2 additional sinking screws, lifting screw for sunk material, n.2 TECNOFER CENTRIFUGAL DRYERS in sequence, 18,5 kw, 720 x 1.500 mm, connection screws, collection hopper, sucking unit, The line is offered as is, where is, Vertical mixer available separately, capacity: ca.500 kg/h depending on material and contamination

Key data: 4000 kN, 763 g/PS, 60 mm

Year of Make: 2000 Clamping force: 400 tons. Shot volume: 848 cm³ Screw diameter 60 mm Injection pressure increased: 2,421 bar Good condition, immediately available

Key data: 450 kN, 80 g/PS, 30 mm

Year of Make: 2001 Clamping force: 45 tons. shot volume: 99 cm³ shot weight: 80 gr./PS Screw diameter: 30 mm good condition

Key data: 250 kN, 29 g/PS, 22 mm

Year of Make: 2005 Clamping force: 25 tons. Capacity: 38 cm³ Screw diameter: 22 mm Good condition

Key data: 500 kN, 95 g/PS, 30 mm

Year of Make: 2005 Clamping force: 50 tons. shot volume: 106 cm³ shot weight: 95 gr./PS Screw diameter: 30 mm with take off robot Good condition

3 x Ferromatik injection moulding machines Ferromatik K155, built in 1999 Ferromatik K275S, built in 2000 Ferromatik K200, built in 2000

Engel injection moulding machine ES 1350 / 275 HL built in 2000 for sale.

Guillotine, reel slitters for paper and plastics 50 T, Working width 2.500 mm, Working height 850 mm, Cutting force 2x25 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 83 mm/sec, Speed down : (80 Bar) 20-41 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulik pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., See item [RES100](.germanplast.eu/listings/4115633-guillotine-reel-slitter) for full description., Force: 50 T

GUILLOTINE PAPER AND FILM REEL SLITTER 50 T, Working width 2.500 mm, Working height 1.250 mm, Cutting force 2x25 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 83 mm/sec, Speed down : (80 Bar) 20-41 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., See item [RES100](.germanplast.eu/listings/4115633-guillotine-reel-slitter) for full description., Force: 50 T

Guillotine, reel slitters for paper and plastics 2500x850mm, Working width 2.500 mm, Working height 850 mm, Cutting force 2x17,5 Ton., no.2 pumps 30 + 30 l/min, Pump volume 21+ 21 ccm, Speed up 84 mm/sec, Speed down (80 Bar) 20-40 mm/sec, Oil tank 175 lt., 9 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 35 T

Guillotine, reel slitters for paper and plastics 35 T, constructed in sturdy painted steel,, Working width 2.500 mm, Working height 1.250 mm, No.2 pumps 30+30 lt/min Volume 21+21 ccm, Speed up : 84 mm/sec, Speed down : (80 Bar) 40-20 mm/sec, Oil tank 175 lt, Cutting force 2x17,5 Ton., 9 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Increased speed system, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 35 T

Guillotine, reel slitter for paper and plastics 25 T, Working width 1.500 mm, Working height 850 mm, Cutting force 1x25 Ton., 7,5 Kw drive 400V 50 Hz, No.1 pump 24 l/min, Volume 16 ccm, Speed : up 53 mm/sec, Speed down (80 Bar): 25 mm/sec, OIl tank : 135 lt., With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 25 T