129,235 used machines on RESALE, but how to find them? Machine Search
ELMETHERM 27 x 4.4 m furnace for plastic pipes was manufactured in 1997 in France. The furnace is used in the process of heating and shaping single-layer plastic pipes with a maximum wall thickness of 3 mm and a diameter from 8 mm to 35 mm. The workpieces are preheated in the machine’s heating pipes and then vulcanised and shaped at 168°C. At the very end, the plastic pipes are moved to a special cooling tunnel, where they are cooled with air at 42.8°C. Automated heat treatment of large quantities of workpieces is possible due to the use of conveyors in the machine that transport the workpieces between the different stages of the process. All functions, such as switching on heating or cooling, are controlled via the SCHNEIDER MAGELIS HMI touch panel. The gas furnace for moulding PA plastic pipes weighs approximately 35000 kg. Technical data of the ELMETHERM 27 x 4.4 m industri ...
- Tube Bundle 12276572 MWM - Suitable for several motors - Please note! Price per piece! The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By constantly adapting and integrating new technologies a ...
Hard PVC pipe extrusion plant for tubes D28/D30/D33, consisting of: Battenfeldextruder B45-24 d, ESDE tube crosshead K 010, vacuum calibration with water bath, Graewe-band trigger BA63, Graewe Abstech-and at chamfer machine STS50, various sleeves, cores, calibrations and jaws, as well as additional tube crosshead Battenfeld RS 8-40
Pipesdiameter outside 42 mm/ DN 32 = € 3,95/ meter 48 mm/ DN 40 = € 4,25/ meter 60 mm/ DN 50 = € 5,25/ meter 76 mm/ DN 65 = € 6,95/ meter 89 mm/ DN 80 = € 7,25/ meter 114 mm/ DN 100 = € 9,75/ meter 139 mm/ DN 125 = € 11,95/ meter
Saw for Pipe Cincinnati RS 25 PZ S 1992 year 4000 Euro
Crossing pipes in different lengths and wall strands in stock Price depending on wall thickness and length
Key data: 60
PE pipe extrusion line - 1-screw extruder: 60 mm Ø, 28 L/D with motor: 37 KW (50hp) with AC speed variator, electrical panel with tube head for 16 and 20 mm. - 3 m vacuum and cooling bathtub with vacuum pump: 5.5 hp. - Cooling bath: 2.5m - Drag trolley (Track): 800 x 100 with variable speed drive. - Minimum inner double coil winder: 330 Ø maximum external 1,200.
1) Drill pipe BTA Ø 43 x 2700 - 20 pcs; 2) Drill pipe BTA Ø 26 x 2700 - 40 pcs; 3) Drill pipe BTA Ø 22 x 2700 - 24 pcs;
Key data: 60
Composite Tube Extrusion Line: A- Extruder, brand: Sterling, 1 spindle: 60 mm Ø 25L/D, Motor: 25 hp with variable speed drive and electrical panel. B- Head for small tube: 0.5 mm and more. C- Water-cooled bathtub: 9 meters with pump and tank. D- Tow Cart, Brand: Mild Ltd Boston: 700x150, Motor Output: 1.5kw with variable speed drive. E- Double winder with guide: 600 mm Ø
Inv. Num. : 7914 Type: PBM 7074 Producer: WEGENER Created: 2015 Parameters: Control system: Siemens Maximum bending angle: 90
Inv. Num. : 8043 Type: ML 100 3Z Producer: NS MAQUINAS Created: 2017 Parameters: Max. workpiece diameter: 10-114 mm Minimum length of the workpiece: 335 mm Number of sanding belts: 6 pieces Abrasive belt speed: 10-30 m/s Sanding belt dimensions: 50 x 940 mm Weight: 600 kg
Maximum Diameter: 110 mm // Minimum Diameter: 32 mm
Maximum Diameter: 800 mm // Minimum Diameter: 280 mm
BANDERA TWIN SCREW PVC PIPES EXTRUDER, for pipes with min/max diam.40/200 mm., extruder with n.2 parallel counter-rotating screws Ø 90 mm, Throghput rate 400 kg/hr, missing of screenchamger (can be added separately), n.2 dies available 40 to 125 mm + 125 to 200 mm., Tooling from 40-200 mm (available diam. 100 mm for O-Ring), Bandera 6 mt.long vacuum calibration tank, IPM haul off unit, IPM saw, IPM belling unit, constructed in 1998, totally refurbished in 2006 by Plasco, machine now disconnected, offered RECONDITIONED., availability: immediate, working width: 40-200 mm Ø, capacity: 400 kg/h, conditions: disconnected, type: pipes extrusion line
ZUCHETTI – Production Line for Metal Pipes General data: Manufacturer: Zuchetti Machine type: Pipe production line Year of manufacture: 2006 Weight: approx. 80000 kg Dimensions (L x W x H): approx. 150000 x 12000 x 2500 mm Condition: Partially overhauled Line components: Double uncoiler for continuous feeding of metal strips Welding junction station for seam joining Horizontal sheet uncoiler for optimized production flow 9 profiling stages for pipe forming High-frequency welding system for durable weld seams Turk heads for final processing Automatic packaging station Electrical panels for control and safety Available roller sets: Square pipes: 10x10 mm; 15x15 mm; 20x20 mm; 25x25 mm; 30x30 mm; 35x35 mm; 40x40 mm; 50x50 mm; 70x70 mm Round pipes: 20 mm; 21.3 mm; 21.8 mm; 25 mm; 25.4 mm; 26.9 mm; 28 mm; 30 mm; 31 mm; 32 mm; 33.7 mm; 35 mm; 36.8 mm; 38 mm; 38.4 m ...
UNUSED, Metal casing pipes for pile driving. Normally used in the construction of bridges, ports, decks, and piers. The driven pipes is filled with concrete, creating an extremely resistant structure. Total available weight is 750 tons. SALES VALUE PER TON $ 1.000,00 USD / KG
Eight steel pipe storage stillages include approx. 280 blue plastic pipes approx. size of each pipe. 1.45m long, OD 170mm, ID 152mm Auction-ID: A1-45187-254
Glatt LR 350 mobile elevating and tipping device for drums and containers etc, max weight load 350kg, fork length approx. 750mm, fork diameter approx. 73mm, approx 910mm gap, max. lift height approx. 1450mm from the floor.
Auction-ID: A1-42012-168
Cake cutting table for plate cakes, Fabr. Coalfish
Squeezers for fillings, Rademaker,
Glaze line, Type Jelly Power Pack JLC, Fabr. Boyens,
Hand pitter for plums and plums, with right- and left-handed handle
A second-hand line for milling and pressing fruit and vegetable pulp. The line consists of: - BELT PRESS TYPE B FRU 800 HK WITH CONTROL PROBE IN FEED HOPPER FLOTTWEG 2008 - FEED HOPPER MEGA 2012 - ROTARY SIEVE WITH EXTERNAL INFLUX DIA. DRUM 355MM LENGTH DRUM LENGTH 1600 MMDRUM 1600 MM MEGA (FLOTTWEG) 2012/14 - METERING RUNG ELEVATOR - BRUSH POLISHER MEGA 2008 - INSPECTION ROLLER CONVEYOR MEGA 2008 - FLOTTWEG SCREW CONVEYOR 2017 - PULP CONTAINER 400L - CENTRIFUGAL PUMP FOR PULP - 500L FLUSHING WATER TANK - CENTRIFUGAL PRESSURE PUMP - PIPES, FITTINGS, ELECTRICAL CONTROL CABINET FLOTTWEG 2008 - JUICE COOLING SYSTEM STM 2018 - TUBE BEAKER SPOMASZ 2018
Chocolate enrobing plant, Fabr. Savy & Goiseau, Crystal 450
Double-sided grinding and polishing bench MEYER type SMPMasch. No. 848 Year of construction 1963Shaft diameter 50 mmGrinding wheel holder 305 mmDisc spacing 1470 mmGrinding-polishing wheel diameter max. 800 mmWorking height 550 mmSpeed 710 / 800 / 950 rpm. Drive power 2x 3 kWNet connection 380 volts, 50 Hz.- two drive motors for each working side separately- star-delta switch for each drive motor separately- speed change by folding the drive belt- dust extraction flange 100 mm-
Technical data: Manufacturer: ogp Type: Smartscope CNC 250 Year of Make: 2004 Travel distances X/Y/Z: X 250 mm, Y 150 mm, Z 200 mm Scale resolution: 0.5 μm Condition Condition: Used Functional: Tested and fully functional
Working width - 1700 mm, material in rolls, Raw material - paper (50-300 g/m²), foil (0.023-0.10 mm) Substances - solvent-based adhesive, water-based adhesive Coating type - Mayer rod, anilox roller, slotted roller Dryer - 18 m long, 7 drying sections, temperature 30°C-170°C, gas drying (blower) Roll diameter - max 1400 mm
Working width – 650 mm Material in rolls Raw material – 950-350 g/m² paper, foil Substances – solvent-based adhesive, water-based adhesive Coating type – Mayer rod, slotted roller Working speed – 0-80 m/min Dryer – 8 m, 3 sections, temperature 3°C-120°C, electric drying Dimensions – 14 m x 1.8 m x 1.8 m Roll diameter – max 1000 mm
Used Rotary FillerâCapper Monoblock 24/8 for PET and HDPE Bottles – Overview This second-hand rotary monoblock combines a 24-head volumetric piston filler with an 8-head pick-and-place spindle capper, engineered for PET and HDPE bottles up to 1 L. Designed for industrial packaging environments, it is a robust component for a used bottling line handling non-pressurized products such as detergents and liquid soap. The machine features a painted iron frame, stainless steel panels, and a fully enclosed protective hood with safety devices, offering reliable performance in high-throughput operations. CE marking and complete documentation support integration within beverage production and home & personal care lines where non-isobaric, non-aseptic filling is required. Technical Specifications & Performance Data Configuration: Rotary fillerâcapper monoblock (24/8) Container materi ...
Table with polishing and grinding machine and rag Auction-ID: A7-45768-9
used
R26115/18 VITS Impregnation and painting system Model: IPA / S / II Built: 1996 Working width: 2200 mm for finish foil and edges Working width: min. 625 mm Heating: Thermal Oil 250 Dryer control: 80 - 220 Speed: 5 - 120 m/min Impregnation plant Painting works Takeup with thermal oil boiler for impregnating, painting of decorative and similar papers from 30 - 240 g/m2 Available: immediately
<br>Tube length: 55-132 (165) cm Pipe width: 30-70 (80) cm 4 plies, photocell, 2 rear color printers<br><br><br>Verf Gbar: at once
<br>Flush cut and kicked end tuber with belt ri's system, 4-ply, photo cell, 0/2 or 4 end button color printer, range perforating system<><br<br>Verf Gbar: at once
used
Ladies and gentlemen, Below you will receive a non-binding offer for railway spare parts for all common railway coaches and railway freight wagons new and partly used: Wheelsets All prices are from Station Europa and the dismantling and all follow-up costs are to be made by the buyer. VAT is not included in the prices. The contractual agreements for the individual offers must be agreed separately and only apply after the contract has been signed. Mistake reserved. All technical details, dimensions, etc. are approximate and are non-binding for the supplier. The technical data are manufacturer or operator information and therefore non-binding for us. Used material is sold to the exclusion of any warranty. We do not accept any liability for used material. Warranty exchange and return are excluded. The material remains the property of the seller until full payment. Inte ...
480 x 320mm; 30,000 c/h; 4 x MID-WS unwinding stations; 4 X ZHF (Siguture systems); SLT station (card glue device); SHT (Gatherer Stitcher Drum); UTR delivery station; UTR-SNT gripper track; UTR SHT Delivery Station; SNT (trimming drum); UTR SNT Transfer Station; UTR-SNT gripper track carry unit UTR-SNT delivery station; missing copy delivery station (UTR); EP station; VP station; HP station ETR insert drum. Opition 2: Mid AWS (relax station); ZF SHT Feeder; UTR gripper track on 4X RAB insert feeder; 4 x VSS stations; Gripper to follow TO VP station-to ETR insert drum Still in operation: No Verf Gbar: Immediately
used
in 2005 refurbished Still in operation: Yes Available: immediately
Main product investors 12 Product supplement Investors Scan Still in operation: No Available: immediately
-Sale by owner our used lines meets after reinstallation by us the Definition RETROFIT COMPLETE equipment, incl. Filzmoser straightening system if you are interested, please request an offer Plans, pictures and CAD drawings are available, without mixer, ready for loading, Filigrandecken and double-walled movement, Filzmoser straightening system with robot. ErICH PETER MACHINES-PLANTS GMBH is engaged in complete solutions for the Realization of construction projects according to EU standards. They are not a construction company, but convey the required knowledge in theory and practice to plan, calculate and implement construction projects. Offers include: • Creation of business, master and execution plans • Sale of various machines and equipment for the production of building materials and prefabricated parts • Commissioning of the plants and personnel train ...
Cat.-Nr. 11-2625 new Cat.-Nr. 11-2625 Material: V2A - AISI 304, 1.4301 Surface: inside and outside 2B=IIIC Tested up to 3,4 bar – working pressure + 2,0/- ,015 bar Upper Bottom: with strong stackable crown with manhole lid DN 400 with 6 x Screws with 1 x overpressure valve with 1 x CO² venting valve Cylindrical Body: with 4 x reinforcing rings for better pressure resistance Lower Bottom: with outlet DN 50 with conical bottom with 4 strong feet can be moved from all sides with forklift / truck pallet Measurements and Weight: Total Height: 1520 mm Diameter: 800 mm Weight: 92 kg Surcharges / each: Fermentation Lock DN 50 Sample Valve Blind Cap DN 50 Fermentation Fittings CIP Cleaning System The price is for one tank. The tank is also available in 300 litres. The price is 1535€ for one ...
Main product investors Suction opening station 1 Tandem product insert stations 2 Product supplement investors 1 Tandem product insert stations Accessories: Still in operation: No Available: immediately
Roller or belt conveyors shifting lengths approx. 25 m
maximum number of results exceeded
please refine your search
50 € 
