ph used for sale

pressure:25 t passage width:1000 mm stroke:800 mm Weight of machine approx.:4 t dimensions:ca. 2054 x 2200 x 3126 mm return capacity:2 t :5 kW Max Working height:800 mm :80 mm/sec :10 mm/sec. :80 mm/sec :800 mm pestle plate:400 x 400 mm table plate:1000 x 800 mm table height over floor:850 mm Table cut-out:650 x 150 mm :200 l pestle is stabilized by 4 per ø 50 mm chrome-plated linear guides:Bronzeführungen pestle strength:122 mm Steel plate on spring rolls:600 x 400 x 15 mm :S7 1200 Lightcurtains by Schmersal:1800 mm ab Boden Monitor:SIEMENS 10 Zoll Installation table on the left of the machine body with 10mm thick plage-milled steel plates:1000 x 800, 850 hoch mm

pressure:250 t passage width:1800 mm stroke:600 mm total power requirement:22 kW weight of the machine ca.:24 t dimensions:ca. 3390 x 3400 x 3800 mm column diameter:160 mm return capacity:25 t max. working heidht:800 mm Table dimensions:1800 x 1600 mm :2350 x 1600 mm table height over floor:900 mm hydraulic table shift:25 mm/sec table load:5 t pre-running speed:10 mm/sec pressure speed:10 Return Speed:25 mm/sec speed rapid traverse:10 mm/sec :600 l Oil cooling (electric):1,5 kW (max) :46er / 10 my Monitor SIEMENS:10 Zoll

pressure:300 t distance between columns:1900 mm stroke:600 mm total power requirement:30 kW weight of the machine ca.:27 t dimensions of the machine ca.:2900 x 3500 x 5400 mm Return Capacity:40 t Main Cylinder:Ø 370 x 350 mm :2 Stk. Ø 80 x 50 mm speed of forward flow:150 mm/sec Return Speed:150 mm/sec Table size:1800 x 1800 x 150 mm Ram plate:1800 x 1800 mm demand for oil:ca. 700 l :max. 900 sec Daylight Opening:900 mm pressure speed:15-8 mm/sec auxiliary motor:5,5 + 2,2 kw auxiliary pump:22 + 5,5 cc Lineal mess stab NOVOTECHNIK:650 mm Table height above ground level (approx.):1000 mm Light sensors front and rear of SICK:900 + 150 mm Monitor:12 Zoll Hydraulic and mechanical protection of the plunger Two-piece auxiliary motors with 2.2 kw Two-piece auxiliary pumps with a power of 6 L/min. Concurrency monitoring (0.5 mm/m²) Fast forward speed adjustable via plc Maximum deflection of the ...

pressure:400 t distance between columns:2300 mm stroke:600 mm total power requirement:37 kW weight of the machine ca.:25 t dimensions of the machine ca.:3300 x 2800 x 5200 mm Main Cylinder:Ø 440 mm :2 Stk. Ø 100 x 60 mm speed of forward flow:200 mm/sec Return Speed:200 mm/sec Table size:2200 x 1400 x 150 mm Ram plate:2200 x 1400 mm demand for oil:ca. 900 l :max. 600 sec Daylight Opening:900 mm pressure speed:15-8 mm/sec auxiliary motor:5,5 + 2,2 kw auxiliary pump:22 + 5,5 cc Lineal mess stab NOVOTECHNIK:650 mm Table height above ground level (approx.):1000 mm Light sensors front and rear of SICK:900 + 150 mm Monitor:12 Zoll Hydraulic and mechanical protection of the plunger Two-piece auxiliary motors with 2.2 kw Two-piece auxiliary pumps with a power of 6 L/min. Concurrency monitoring (0.5 mm/m²) Fast forward speed adjustable via plc Maximum deflection of the table at 0, 07mm/m²

pressure:200 t distance between columns:1200x1000 mm stroke:600 mm total power requirement:32,5 kW weight of the machine ca.:20,5 t draw back pressure:20 t :1 Stück voltage:400 V frequency:50 Hz :24 V :Rexroth/Bosch dayligth:800 mm working area:1200x1000 mm :1200x1000 mm work height max.:1100 mm :170 mm/sek. :150 mm/sek. :15 mm/sek. quantity of oil:500 l :220 V memory:200 Programme :20-200 über Monitor t :5-170 mm/sec. :0-10 sec :2-10 mm/sec :750x950 mm :300 mm :5-50 t :2-80 mm/sec :1000 kg

A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery Slightly used, in like new condition, classifier mill Hosokawa ACM 5 Pharma. This micronizer allows you to obtain a perfectly controlled top cut. It can be used to fine grind different products. The comminution occurs in the lower part of the grinding chamber where the feed particles are crushed. Thanks to the adjustable classifier wheel on the upper part of the grinding chamber, the ...

Used machine in good condition. Available for immediate delivery. - Throat: 420 mm - Working area: 3.050 mm - Pressure force: 160 t - Bending length: 3.050 mm - Power: installed max: 15 kW - Weight: 12.000 kg - Dimensions (long x wide x high): 5.000 x 2.000 x 3.000 mm

pressure:100 t passage width:500 mm stroke:400 mm weight of the machine ca.:5 t dimensions:1300 x 2800 x 2900 mm Approaching Speed max. :90 mm/sec pressure speed:4-12 mm/sec Travel:400 mm pestle plate:700 x 500 mit T-Nuten mm table plate:700 x 500 mit T-Nuten table height over floor:850 mm Oil Tank Capacity:140 l Return Speed:100 mm/sec Main cylinder:1 Stück Cylinder diameter:220 mm Auxiliary cylinder:2 Stück Auxiliary cylinder diameter:50 x 30 mm Engine Output:11 kW pump:23 l Light sensors sick:600 + 150 mm Monitor:7 Zoll

pressure:500 t passage width:1600 x 1300 mm stroke:1100 mm Table size:1600 x 1300 mm open height:1700 mm Press speed:25,2 - 9,4 mm/sec Approach Speed:300 mm/sec return speed:200 mm/min machine dimensions LxWxH:2800 x 1800 x 7200 mm Weight (approx.):55 t Description of the press frame The frame is designed as a frame construction with 2 operating sides. It consists of highly dimensioned braces, which are tightly and rigidly welded with upright steel ribs. The complete welding part is processed on precision machines. As a stiff box construction. The underside of the box is formed by a solid welded steel plate, which is prepared for the assembly of insulation and heating plates. The complete welding part is processed on precision machines. Integrated guide and cylinder connections in a power optimised design. Plunger Guide The plunger is guided diagonally through a prism guide, i.e. the ang ...

pressure:650 t passage width:920 mm stroke:1750 mm weight of the machine ca.:ca. 47 t Table area:2000 x 1500 mm ram surface:2000 x 1500 mm Daylight Opening:2100 mm Hydraulic:203 bar closing speed:500 mm/min pressing speed:0,5 - 10,4 mm/sec opening speed:250 mm/sec Solve speed:0,5 - 66,4 mm/sec Return Capacity:150 t total power requirement:75 kW Measurements (approx.):4,4 x 2,5 x 7,5 m

pressure:15 t stroke:160 mm weight of the machine ca.:330 kg Oil tank capacity:10 l

pressure:40 t passage width:2500 x 1300 mm stroke:1000 mm total power requirement:7 kW weight of the machine ca.:12 t draw back pressure:4 t Controll:Zweihandbedienung cylinder:1 work height max.:2200 (zwischen Stößel und Tischplatte) mm working area:2500 x 1300 mm Table dimensions:2800 x 1300 mm pestle plate:2800 x 1300 mm table height:800 mm pre-running speed:9,8 mm/sec work speed:9,8 mm/min return speed:18 mm/sec Oil Tank Capacity:150 l

pressure:160 t stroke:600 mm total power requirement:7,5 kW weight of the machine ca.:7 t draw back pressure:16 t :1 Stück Column-Diameter:160 mm dayligth:800 mm table surface area:1200 x 800 mm :400 mm table height:850 mm table load:5 t pre-running speed:1 bis 9,8 mm/sec return speed:1 bis 9,8 mm/sec quantity of oil:220 l

pressure:40 t stroke:500 mm total power requirement:5 kW weight of the machine ca.:2,5 t dimensions of the machine ca.:2950 x 1300 x 2000 mm return capacity:6 t work height max.:700 mm pre-running speed:250 mm/sec :20 mm return speed:200 mm/sec pestle plate:500 x 400 mm table plate:600 x 450 mit T-Nuten mm Table cut-out:150 mm Durchmesser table height:1000 mm :200 l Oil Cooling:elektrisch light-barrier:700 mm

pressure:110 t passage width:1500 mm stroke:650 mm total power requirement:15 kW weight of the machine ca.:11 t dimensions:ca. 2640 x 3200 x 3650 mm return capacity:11 t column diameter:120 mm Max Working height:1000 mm Table dimensions:1990 x 1000 mm Ram size:1990 x 1000 mm Drivering away pestle:650 mm table height over floor:800 mm pre-running speed:10 mm/sec Pressure Speed:10 mm/sec Oil Tank Capacity:200 l Oil cooling (electric):1,5 kW (max)

pressure:63 t passage width:700 mm stroke:500 mm Approx. weight (w/o operational materials):5,1 t Measurements L x W x H:ca. 1500 x1600 x 2995 mm Return Capacity:6 t Engine Output:11 kW Max Working height:700 mm Approaching Speed max. :140 mm/sec Pressure Speed:15 mm/sec. Travel:500 mm Ram plate:600 x 540 mm Table size:750 x 600 mm Table height above ground level:850 mm Oil Tank Capacity:150 l Control voltage:24 V Frequency:50 Hz Siemens Control System:S7 1200 Monitor:Siemens 12 Zoll Special feature: When operating at 260bar the machine reaches a pressure level of 70 tons.

pressure:40 t passage width:2500 x 1300 mm stroke:1000 mm total power requirement:7 kW weight of the machine ca.:12 t draw back pressure:4 t Controll:Zweihandbedienung cylinder:1 work height max.:2200 (zwischen Stößel und Tischplatte) mm working area:2500 x 1300 mm Table dimensions:2800 x 1300 mm pestle plate:2800 x 1300 mm table height:800 mm pre-running speed:9,8 mm/sec work speed:9,8 mm/min return speed:18 mm/sec Oil tank capacity:150 l

pressure:30 t passage width:1000x1000 mm stroke:800 mm total power requirement:3 kW weight of the machine ca.:5 t dimensions of the machine ca.:3360x1300x1360 mm return capacity:3 t column diameter:75 mm traversing speed:bis 200 mm/sec. :0-10 mm/s :200 mm/sec table height over floor:900 mm distance table - lower edge of ram:1000 mm :126 mm diameter of piston:71 mm

pressure:20 t stroke:600 mm table surface area:2000 x 600 mm dimensions:ca. 3500 x 1200 x 2800 mm total power requirement:3 kW pre-running speed:9,9 mm/sec return speed:25 mm/sec Pressure power:180 bar :100 l weight of the machine ca.:3 t :5 Zoll

pressure:200 t distance between columns:1550 mm stroke:400 mm dimensions:ca. 4400 x 3250 x 4100 mm Table dimensions:1500 x 1500 mm distance table - lower edge of ram:1590 mm return capacity:20 t total power requirement:20 kW Oil Cooling:1,5 kW stroke speed:25 mm/sec down speed:10 mm/sec :250 l table plate:120 mm Table cut-out:550, 450, 350 und 200 mm table speeds:30 mm/sec

pressure:110 t passage width:1500 mm stroke:650 mm total power requirement:15 kW weight of the machine ca.:11 t dimensions:ca. 2640 x 3200 x 3650 mm return capacity:11 t column diameter:120 mm Max Working height:1000 mm Table dimensions:1990 x 1000 mm Ram size:1990 x 1000 mm Drivering away pestle:650 mm table height over floor:800 mm pre-running speed:10 mm/sec Pressure Speed:10 mm/sec Oil Tank Capacity:200 l Oil cooling (electric):1,5 kW (max)

pressure:160 t passage width:1200 mm stroke:600 mm Weight of machine approx.:7 t dimensions:ca. 2400 x 1400 x 3400 mm return capacity:16 t Max Working height:800 mm Return Speed:25 mm/sec pestle plate:1670 x 800 mm table plate:1670 x 800 mm table height over floor:800 mm Oil cooling (electric):1,5 kW (max) Engine Output:18 kW speed of forward flow:10 mm/sec pressure speed:10 mm/sec Travel:600 mm Oil Tank Capacity:300 l

pressure:110 t passage width:1300 mm stroke:1500 mm Weight of machine approx.:12 t dimensions:ca. 2300 x 2090 x 4200 mm return capacity:11 t Max Working height:1500 mm pestle plate:1730 x 1100 mm table plate:1730 x 1100 mm table height over floor:700 mm column diameter:140 mm Thickness of ram plate:100 mm thickness of clamping plate:100 mm Noise Level (Max.):67 dB Color machine body:7035 RAL Color moving parts:2009 RAL Colour other components:7021 RAL Colour of balcony and casing:1021 RAL motor capacity:18 kW Approaching Speed max. :300 mm/sec pressure speed:15 mm/sec Oil Tank Capacity:150 l Siemens Control System:S7 1200

pressure:40 t passage width:850 mm stroke:500 mm Weight of machine approx.:ca. 3,8 t dimensions:ca.1300 x 1800 x 3200 mm return capacity:4 t pestle plate:600 x 450 mm table plate:750 x 720 mm table height over floor:850 mm Oil cooling (electric):1,5 kW (max) max. working heidht:700 mm motor capacity:12,7 kW Approaching Speed max. :140 mm/sec pressure speed:15 mm/sec Return Speed:140 mm/sec Oil Tank Capacity:160 l Monitor:WEG - 10 Zoll Siemens Control System:S7 1200

pressure:63 t passage width:700 mm stroke:500 mm Approx. weight (w/o operational materials):5,1 t Measurements L x W x H:ca. 1500 x1600 x 2995 mm Return Capacity:6 t Engine Output:11 kW Max Working height:700 mm Approaching Speed max. :140 mm/sec Pressure Speed:15 mm/sec. Travel:500 mm Ram plate:600 x 540 mm Table size:750 x 600 mm Table height above ground level:850 mm Oil Tank Capacity:150 l Control voltage:24 V Frequency:50 Hz Siemens Control System:S7 1200 Monitor:Siemens 12 Zoll Special feature: When operating at 260bar the machine reaches a pressure level of 70 tons.

pressure:63 t table length:1200 mm table width:1000 mm stroke max.:1050 mm dimensions:ca. 3350 x 1800 x 4700 mm draw back pressure:6 t Approx. weight (w/o operational materials):10 t column diameter:120 mm Fold-down upper tool:180 Grad Swivable Table:75 Grad table speed:25 mm/sec Table tilting:75 Grad table extendable:1100 mm table load:5 t Engine Output:10 kW Oil Tank Capacity:200 l Oil cooling (electric):1,5 kW (max) Monitor:(WEG) 12 Zoll

pressure:1000 t passage width:1500 mm stroke:800 mm total power requirement:91 kW weight of the machine ca.:68 t dimensions:3850 x 2900 x 6000 mm return capacity:100 t Table dimensions:1500 x 2250 mm :1500 x 2250 mm table height over floor:1300 mm pre-running speed:200 mm/sec return speed:200 mm/sec Pressure Speed:10 mm/sec :1200 l Oil cooling (electric):1,5 kW (max) Max Working height:1000 mm :200 mm/sec Monitor:12 Zoll

pressure:160 t passage width:1000 mm stroke:800 mm total power requirement:22 kW weight of the machine ca.:13 t dimensions:2300 x 2850 x 4000 mm return capacity:16 t Table dimensions:1430 x 1000 mm :1430 x 1000 mm table height over floor:850 mm pre-running speed:200 mm/sec return speed:200 mm/sec Pressure Speed:15 mm/sec :400 l Oil cooling (electric):1,5 kW (max) Max Working height:1000 mm :200 mm/sec Monitor:10 Zoll

pressure:200 t distance between columns:1900x1200 mm stroke:1000 mm total power requirement:44 kW weight of the machine ca.:32 t dimensions of the machine ca.:4793 x 3365 x 4779 m Hydraulic block:Bosch Rexroth demand for oil:800 l Sliding door front with a closing speed of:300 mm/sec open height:1400 mm Table Height:820 mm Ram Height:1000 mm Lifting capacity:20 t Lowering speed in the empty journey:80 bis 270 mm/sec Press speed:7 bis 25 mm/sec On driving speed:50 bis 170 mm/sec bending stiffness according to standard:0,2 mm Siemens Control System:S7 1200 Monitor:WEG 12 Zoll

pressure:100 t passage width:650 mm stroke:500 mm weight of the machine ca.:10 t dimensions:4800 x 1300 x 2650 mm return capacity:10 t :29 kW Max Working height:1000 mm :10 mm :10 mm/sec. :500 mm pestle plate:600 x 600 mm table plate:600 x 600 mm table height over floor:700 mm :600 l speed rapid traverse:10 mm/sec Oil cooling (electric):1,5 kW (max) Monitor SIEMENS:7 Zoll

pressure:40 t passage width:1000 mm stroke:400 mm Weight of machine approx.:3,5 t dimensions:2065 x 700 x 2905 mm return capacity:4 t Max Working height:700 mm Return Speed:25 mm/sec pestle plate:1320 x 600 mm table plate:1320 x 600 mm table height over floor:750 mm Oil cooling (electric):1,5 kW (max) Engine Output:8 kW speed of forward flow:10 mm/sec pressure speed:10 mm/sec Oil Tank Capacity:200 l speed rapid traverse:10 mm/sec column diameter:100 mm :2400 ? Maintenance Balcony:3600 ? :4600 ? Ground tub of lacquered steel:850

pressure:350 t passage width:3000 mm stroke:900 mm total power requirement:75 kW weight of the machine ca.:60 t dimensions:2660 x 5400 x 5700 mm return capacity:35 t Table dimensions:3610 x 1600 mm :3610 x 1600 mm table height over floor:900 mm pre-running speed:230 mm/sec return speed:170 mm/sec :2000 l max. working heidht:1700 mm pressure speed:21 mm/sec speed rapid traverse:200 mm/sec Oil cooling (electric):3 kW (max) :S7 1500 Monitor:WEG 12 Zoll

pressure:20 t passage width:1500 mm stroke:500 mm total power requirement:3 kW weight of the machine ca.:6,5 t dimensions:ca. 2700 x 1700 x 2700 mm Max Working height:1500 mm return capacity:2 t Table dimensions:1500 x 2100 mm :1500 x 2100 mm table height over floor:900 mm pre-running speed:10 mm/sec pressure speed:10 mm/sec return speed:25 mm/sec speed rapid traverse:10 mm/sec :150 l :AW46 Monitor:(WEG) 7 Zoll

pressure:110 t stroke:400 mm weight of the machine ca.:4,5 t dimensions:ca. 1650 x 1150 x 2800 mm return capacity:11 t total power requirement:11 kW Max Working height:500 mm :10 mm :10 mm/sec. speed rapid traverse:10 mm/sec :400 mm pestle plate:600 x 500 mm table plate:800 x 700 mm Table cut-out:150 x 150 mm table height over floor:900 mm :250 l Monitor SIEMENS:7 Zoll Side trim:2.800,- ? :4.800,- ? Light barriers front and back:2.400,- ?

pressure:20 t passage width:500 mm stroke:250 mm Weight of machine approx.:2,6 t dimensions:1200 x 1400 x 2900 mm power capacity:11 kW table plate:450 x 400 mm Table cut-out:150 x 150 mm table height over floor:900 mm max. working heidht:500 mm Return Capacity:2 t Approach Speed:300 mm/sec pressure speed:50 mm/sec speed rapid traverse:300 mm/sec Travel:250 mm Oil Tank Capacity:250 l Oil cooling (electric):1,5 kW (max) Monitor:Siemens 10 Zoll

pressure:220 t passage width:1500 mm stroke:400 mm weight of the machine ca.:5,2 t dimensions:ca. 4000 x 1950 x 2900 mm return capacity:20 t total power requirement:30 kW Max Working height:500 mm :10 mm :10 mm/sec. Return Speed:25 mm/sec speed rapid traverse:10 mm/sec pestle plate:2000 x 400 mm table plate:2000 x 600 mm table height over floor:900 mm :500 l Oil cooling (electric):1,5 kW (max) measuring system:TURCK oder Balluff :S7 1500 oder PILZ PSS 4000 Monitor SIEMENS:oder OMRON

A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery Refurbished Pharmapaktor APC L200/50. The Hosokawa Alpine APC L200/50 Pharmapaktor is the perfect compactor to test the product behaviour with this technology, while it even allows to keep a continuous production at small scale if needed. The Pharmapaktor can be fitted with a flake crusher to granulate the resulting compacted material increasing the possibilities of end produc ...

Rental unit, not for sale. A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery Rental Multiprocess System in Pharma design. Stand-alone lab scale grinding and classifying plant. This compact plug-and-play system is perfect for R&D and small-scale productions. It operates in small batches of a few kilos. The system can be fitted with different modules (one at a time) to either grind or classify different products, both coarse and ...

Type: Treif Phoenix Loading sections (L x W x H): 280x170x100 mm Cutting length: 1,0 – 30,0 mm Saw blades 1 set Capacity: up to 2500 kg/hour Electric power: 6 kW Machine dimension in cm: Width: 100 cm Lenght: 220 cm Height: 150 cm Delivery time: 10 working days after advanced payment

PONAR ŻYWIEC PHM 160 D hydraulic press manufactured in Poland in 1990 is used for machining metal and processing plastics (e.g. polofen or melamine) or rubber. The machine characterised by its high reliability, performs precise machining with a force of 160 tonnes in manual mode as well as in semi-automatic or automatic mode, thanks to its being equipped with time relays. The gantry press is also equipped with, among others, a hydraulic ejector with a force of 60 tonnes and two temperature controllers for the upper and lower parts of the heating plate. The offered machine was purchased from the university and has never worked during typical production. The total weight of the machine is 4000 kg. Technical parameters of the PONAR ŻYWIEC PHM 160 D press - maximum pressing force: 160 t (1600 kN) - ejector force: 60 t (600 kN) - working table surface (L x W): 800 x 800 mm - pressing ...

max. wheel diameter: 215 mm gear width: 40,65 mm max. module: total power requirement: 20 kW weight of the machine ca.: 10 t Max. external Ø of workpiece 215 mm Tooth profile, height x width 16 x 40.65 mm No. of teeth 5 - 200 Max. tooth ratio 1 : 10 Grinding wheel Ø 51 - 190 mm Grinding wheel speeds 1,000 - 6,000 rpm X Axis (horizontal) 152 mm Y Axis (vertical) 178 mm Z Axis (slide base plate) 304 mm Distance from middle of machine to middle of workspindle 115 mm Axial speed 125 mm/sec Workpiece speeds 0 - 30 rpm Workspindle bore, conical 3 29/32 inch Total electrical load 20 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features FANUC CNC Control, Model 150 MB, for 7 axes, with monitor and direct input. Automatic calculation of all workpiece and grinding parameters. Extensive coolant equipment with filter system, band filter, etc. Driv ...

pressure: 5 t table size: 200 x 250 mm pneumatic: weight of the machine ca.: 100 kg : The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

UNICRAFT-Hand Pallet Truck-PHW-2508 Product name: PHW professional pallet truck Manafacture: Unicraft Item number: 6152512 Year of construction: 05/2023 Technical details: • Load capacity: 2.5 t • Carrying width: 540 mm • Fork width: 160 mm • Fork length: 1,150 mm • min. fork height: 85 mm • max. fork height: 200 mm • Turning radius: 1,281 mm • Steering angle: 205° • Diameter swivel castors: 200 mm • Swivel castor width: 50 mm • Diameter fork rollers: 80 mm • Fork roller width: 70 mm • Dimensions (LxWxH): 1,550 x 540 x 1,235 mm • Weight: 67 kg • Stable, robust quality • Fully hydraulic lifting and lowering device • Hydraulic pump with hard chrome-plated piston and pressure relief valve • Lowering speed infinitely adjustable via drain valve • Frame and fork in very stable and torsionally stiff shell construction • Er ...

UNICRAFT-Hand Pallet Truck-PHW-2508 Product name: PHW professional pallet truck Manafacture: Unicraft Item number: 6152512 Year of construction: 05/2023 Serial Number: 121098013092 Technical details: • Load capacity: 2.5 t • Carrying width: 540 mm • Fork width: 160 mm • Fork length: 1,150 mm • min. fork height: 85 mm • max. fork height: 200 mm • Turning radius: 1,281 mm • Steering angle: 205° • Diameter swivel castors: 200 mm • Swivel castor width: 50 mm • Diameter fork rollers: 80 mm • Fork roller width: 70 mm • Dimensions (LxWxH): 1,550 x 540 x 1,235 mm • Weight: 67 kg • Stable, robust quality • Fully hydraulic lifting and lowering device • Hydraulic pump with hard chrome-plated piston and pressure relief valve • Lowering speed infinitely adjustable via drain valve • Frame and fork in very stable and torsionally sti ...

Portal straightening press with 400 T capacity Oil-hydraulic double column press a) No-load and pressing speed up to 17 mm/sec b) Opening speed up to 60 mm/sec c) Table size 6000x3000mm d) Open height 1500 mm e) Total size approx. LBH 6000 x 5000 x 4500 mm f) OIL temperature display on the tank g) Lubrication via lubrication nipples h) table in grid construction, i) Operation on swivel arm, mounted on the bridge j) Pressure setting from 60 T to 400 T via MONITOR k) Bridge moves through two geared motors, over racks l) Cylinder moves to the left and right over racks m) Machine body powder-coated, or double-painted n) T-grooves according to customer requirements o) Cylinder induction hardened PORTAL PRESS Thermally neutral 80 – 120 °C Number of operating pages 3 pages Forces Pressing force max. 4000 kN Free tearing force ...

2 x 10 T, adjustable from 1.3 to 10 T Plunger size 250x250mm forward 10 mm second Backwards 25 mm second Travel 100 mm per side, Interior 200 to 400 mm Two-hand operation Motor 1 KW Tank for 60 L hydraulic oil the machine can also be supplied in other sizes and thicknesses.

Portal straightening press with 300 T capacity a) No-load and pressing speed up to 17 mm/sec b) Opening speed up to 55 mm/sec c) Table size 2500x1600mm d) Open height 700 mm e) Total size approx. LBH 4500 x 2300 x 3700 mm f) OIL temperature display on the tank g) Lubrication via lubrication nipples h) Table in grid construction, with T grooves according to customer requirements, otherwise 22mm i) Operation on swivel arm, mounted on the bridge j) Pressure setting from 50 T to 300 Tvia MONITOR k) Bridge moves through two geared motors, over racks l) Cylinder moves to the left and right over racks m) Machine body double painted n) Cylinder induction hardened Design Press type PORTALPRESSE Thermally neutral 80 – 120 °C Number of operating pages 3 pages Forces Pressing force max. 3,000 kN Free tearing force max. 500 kN Pressure build-up time Closed tool St ...

Technical details Pressure 110 t Technology Passage width 1200 x 1000 mm Stroke 1200 mm Machine weight approx. 12 t Space requirement approx. 4500 x 4300 x 2700 mm Master cylinder 1 piece Installation height (distance table to plunger plate) 1200 mm Table height 700 mm Table can be extended by 1200 mm Table tiltable by 45 degrees Upper tool folds down by 180 degrees Table rotatable by 180 degrees Table load max. 10 t Travel speed of the table 25 mm/sec Flow speed 195 mm/sec Return speed 130 mm/sec Working speed adjustable from 0 to 10 mm/sec. Table area between the columns 1250 x 1000 mm Engines WEG Accessories Paint structure RAL 7035 (light grey) Additional information Painting cladding, doors, maintenance balcony RAL 1021 (Yellow) Painting accessories RAL 7021 (dark grey) Columns and cylinders are made of tool steel SAE 1045 (identical to German standard C4 ...

Bending machine FAVRIN 3100×30 PHLS CNC (A3708) Type: hydraulic Max worklength: 3100 mm Eletric motor (power) 75 HP Courant needed 380V Weight 32 ton Machine was previously used to bend Hardox workpieces. bending capacities examples: – 3100 x 25 mm > multi stage bending for large radiuses – 2500 x 30 mm > multi stage bending for large radiuses – 3100 x 17 mm > single stage bending – 2500 x 25 mm > single stage bending full CNC corner + backgauge control upper hydraulic clamping of tools clamping force: 220 ton max bending angle: 110° max open: 500 mm Tooling included for radius bending Also 2 new extra cilinders included