pet blow moulding used for sale

Offered is a used D 36 S Delta Hybrid unit in good condition. If you have any questions, please do not hesitate to contact us.

The GM 60 S unit can be adjusted to your performance data. The blower stage is completely overhauled. If you have any questions, please do not hesitate to contact us.

Fuel: Natural gas Manafacture: Remko Type: VRS170 Heating power: 198 kW Air mass flow: 12,000 m³/h Mains gas pressure: 2.6 bar

Fuel: Natural gas Manafacture: Remko Type: VRS170 Heating power: 198 kW Air mass flow: 12,000 m³/h Mains gas pressure: 2.6 bar

See PDF attached

diameter range 8 mm number of dies 4 number of stations (incl. cut off) 7 cutting length 20-105 mm shaft length under head 85 mm output - pieces/min 120 max. thread length 70 mm max. width across flats 14 mm

diameter range 4-8 mm shaft length under head 8-80 mm max. cut-off length 110 mm output pieces/min 140

diameter range 2-7 mm shaft length under head 120 mm cutting length 140 mm output - pieces/min 300

diameter range 2-4,76 mm shaft length under head 45 mm max. cut-off length 60 mm output pieces/min 470

diameter range 4-9 mm shaft length under head 100 mm cutting length 120 mm output pieces/min 100

good condition diameter range 10-20 mm shaft length under head 180 mm cutting length 230 mm output - pieces/min 45/50/56/63 press power 160 t plane of stroke 240 mm

diameter range 2-5,2 mm shaft length under head 120 mm cutting length 146 mm output pieces/min 105

diameter range 3-6 mm shaft length under head 35-120 mm max. cutting length 146 mm output- piece/min 90

diameter range 5,0-10 mm shaft length under head 120 mm max. cutting length 170 mm output- piece/min 130

diameter range 6-16 mm number of dies 4 number of stations 7 cutting length 340 mm shaft length under head 65-300 mm output - pieces/min 60-90 max. thread length 65-150 mm press power 150 to

diameter range 6-10 mm number of dies 4 number of stations (incl. cut off) 7 cutting length 75 mm shaft length under head 50 mm output - pieces/min 285 max. width acros flats 17 max. thread length 50 mm

bushing cut-off diameter range 10-22 mm number of dies 4 number of stations (incl. cut off) 7 cutting length 200 mm shaft length under head 160 mm output - pieces/min 60 max. thread length 95 mm max. width acros flats 32 mm

bushing cut-off diameter range 15 mm number of dies 4 number of stations 6 cutting length 127 mm shaft length under head 20-90 mm output - pieces/min 200 max. thred length 63,5 mm press power 130 to

Manufacturer: AXIS Type: 703MG7.5T Capacity: 3420 m3/h Vacuum: -270 mbar Operating pressure: 260 mbar Power: 7.5 kW

Overview The BLOMAX 4 blow molder was manufactured by the German company SIG Corpoplast (now KHS) in 2006. It has been overhauled by a machine builder and can be inspected in dry operation. Blow molds are not included, but can be obtained.  Technical details  Output: up to 7,200 bph 4 cavities Dimensions: 4960 mm x 3900 mm x 3000 mm  Weight: 15 t  Operating hours: 44.736  Bottles Volume: 200 ml - 2000 ml   Max. Diameter: 115 mm  Max. Length: 350 mm Preforms  Length: 60 - 200 mm Max. Support ring diameter: 35 mm  Scope of delivery  Blow molder is completely equipped with the system for preform feeding (silo, elevator, sorting, chute)

Overview  The KSB4000 blowing machine was manufactured in 2002 by the Austrian manufacturer KOSME. This machine can produce 0.5l, 1.5l & 2.0l bottles. Technical details  Capacity: 4.000 bph 4 cavities Scope of delivery  Preform feeder, Three types of molds for 0.5L, 1.5L and 2.0L bottles

Overview The machine built in 2015 by Lithuanian manufacturer FlexBlow. The machine has been overhauled and new dumper, hopper and unscrambler will be built. The machine is already disassembled. Please note that the picture of the advertisement is for reference only.  Techn. Details  Capacity: 5.500 bph (at 1,0l)  Number of cavities: 4  Max. bottle neck: 48 mm Max. bottle size: 2,0l  Previously used neck size: 38 mm  Spare parts, blow molds and new set of neck specific parts can be purchased additionally Siemens controller and English operational language

Overview The BLOMAX 16 blow molder was manufactured by the German company Krupp Corpoplast (now KHS) in 2000 and until recently was part of a PET filling line at a major Austrian beverage bottler. The blow molder is now becoming available as the owner is investing in a completely new line. Technical details Output: up to 24,000 bph 16 cavities Volume: 0.2 - 3.0 l  Peripherals  Preform feeder | Tanner AG | SBT-3012 | -  Tipper  Silo Lift  Sorting  Chute

Overview The KSB3000 blowing machine was manufactured in 2000 by the Austrian machine builder KOSME. It is located at a machine builder and can be visited in dry run to see the functionality of the machine.  Technical details  Capacity: 3.600 bph  3 cavities Dimensions (LxWxH): 6830 mm x 2860 mm x 2450 mm  Space requirement approx. 9x5 m²  Weight: 4,5 t  Operating hours: 23.824   Bottles Volume: 250 ml - 2500 ml   Max. Diameter: 110 mm  Scope of delivery  Blow molding machine is completely equipped with the system for preform feeding (the silo, the preform elevator, the preform aligner and the preform infeed).

Overview This blowmoulder was manufactured in 2005 by Italian manufacturer SMI. Techn. Data 14 cavities Formats: 0,5 – 2,0 l, round, squared Scope of delivery Blowmoulding machine SMI SR14 Chiller ASKI year 2005 Preform tipper Preform feeder

Type: ELMO-G 2BH1 490-1AH13 2-flutig pmax.: 180 mbar Motor: Siemens Power: 0.43 kW Voltage: 230/ 400 V Frequency 50/ 60 Hz Protection class: IP54 New !

Side channel blower EG&G ROTRON DR068DJ9Y Volumetric flow: 21.6 m3/h 75 watts 110 / 220 V (luminous flux) Dimensions: 220 x 190 x 180 mm

Manufacturer: Rietschle Type: SKG 214-2.02 with intake filter Power: 4 kW Speed: 2850 rpm voltage: 230-400 V Frequency: 50 Hz hot air used, tested !

Manufacturer: VEM Type: LRH 90/1 Volumetric flow: 0.03 - 0.11 m3/s Total pressure increase: 5120 - 2060 Pa Power: 1.1 kW Speed: 2800 rpm Voltage: 220-380 V Dimensions: approx. 800 x 800 x 450 mm used, tested !

Manufacturer: KIPSZER Type: CK 31/4 Volumetric flow: 690-1100 m3/h Power: 0.25 kW speed: 1400 rpm voltage: 220-380 V frequency: 50 Hz used, tested !

Volume flow: 6760m³/h, temperature increase: 128°C, rotational speed: 2670/min, connected load: 88.76kW, length: 2438mm, width: 1922mm, height: 2453mm, weight: 3.8t, including documentation.

Side channel blower, side channel blower 28H4 110-OHC 32 50 Hz 1.5 KW 3x 240/400 V IP54 New ! Overall dimensions: 44x44x40 cm

D-melting insert, fuse insert, fuse element, 100 pieces PAGUS TGL 0-49360 ELN 136 63 421 Size: E16 Rated current: 16 A Slow Rated voltage: 500 V Contact diameter: Ø 10 / 12 mm installation length: 51 mm Packing unit: 4 boxes of 25 fuses Other quantities on request ! New ! Dimensions ( single fuse ): 51 x 13 x 13 mm Dimensions ( single package ): 215 x 215 x 70 mm

centrifugal fans; Centrifugal blower Overall dimensions: 120x90x106 used, tested !

Centrifugal fan, centrifugal fan, centrifugal fan SIEMENS SIMODRIVE 6SN1162-0BA02-0AA2 with SHIELD CONNECTION PLATE 6SN 1162-0EA00-0KA0 Fan: EBM D2D133-AB06-30 Fan wheel: Ø 120 mm n: 2500 rpm Motor : 0,,12 kW 360 - 480 V 3AC 2x Ø 115 mm Output: 210 x 65 mm spare part for machining center HECKERT CWK400 D ! used, tested ! Dimensions: 800 x 720 x 670 mm

Centrifugal blower, multi-stage PAGUS Fan wheel diameter: Ø 230 mm Steps: 5 input: Ø 77 mm, flange: Ø 140 mm, bolt circle: Ø 100 mm, 4x bore: Ø 6,, 5 mm Output: Ø 100 / 113 mm ( inside / outside ) Shaft diameter: Ø 28 mm Wavelength: 26 mm Material: aluminum (housing, impellers, dividers ) used, tested ! Dimensions: 550 x 460 x 420 mm

Blow-off valve, blow-off valve SCHMALZ ERS ABL-VENT EVE-TR 10-50 Thread: 1 ( inch ) Spare part for vacuum pump EVE-TR Size: 10-50 New ! Dimensions: 60 x 41 x 41 mm

Radiator with blower, cooling fan, oil cooler VZDUCHOTECHNIKA PN125045 Radiator : 230 x 200 x 70 mm Fan wheel: Ø 200 mm engine: 4AAAM63B2KY3 0,25 KW 2760 rpm 220 / 380 V 3AC used, tested ! Dimensions: 370 x 310 x 310 mm

Radiator with blower, cooling fan, oil cooler EMMEGI, EBM Cooler : 220 x 220 x 60 mm Fan wheel: Ø 200 mm Fan: EBM Type A2D200-AH18-01 68 / 70 W ( 50 / 60 Hz ) 2600 / 2900 rpm ( 50 / 60 Hz ) 230 / 400 V 3AC 50 / 60 Hz used, tested ! Dimensions: 430 x 210 x 300 mm

Radiator with fan, cooling fan, oil cooler VEM DM 102/4-A6/509 Radiator : 380 x 45 x 300 mm Fan wheel: Ø 300 mm motor: 0,,06 KW 1400 rpm 220 / 380 V 3AC IP44 used, tested ! Dimensions: 490 x 300 x 430 mm

Suction and blower hose, spiral hose PAGUS Ø 100 mm x 5 m Inner diameter: Ø 100 mm ( spiral stretched ) outer diameter: Ø 116 mm ( spiral compressed ) Length: 5 m ( unloaded ) As good as new ! Dimensions ( packaging ): 800 x 400 x 400 mm

Suction and blower hose, spiral hose PAGUS Ø 160 mm x 9.3 m inner diameter: Ø 160 mm (spiral stretched ) outer diameter: Ø 170 mm (spiral compressed) length: 9.3 m ( unloaded ) as good as new ! Dimensions ( packaging ): 1200 x 800 x 400 mm

Radiator with blower, cooling fan, oil cooler EBM W2E 250 AB05 01 ( W2E250AB0501 ) Cooler : 250 x 240 x 80 mm Fan: Ø 250 mm 0,135 KW 2500 rpm 220 V 500 x 360 x 200 mm

Radiator with blower, cooling fan, oil cooler VEM DM 102/4-A6T/609 ( DM102/4-A6T/609 ) Cooler : 380 x 300 x 45 mm Fan: Ø 300 mm 0,06 KW 1400 rpm 220 / 380 V 500 x 470 x 270 mm

Overview This blowmoulder was built in 1992 from French manufacturer Sidel. It can produce up to 4.000 bottles per hour. Techn. Details Capacity: 4.000 bph 4 cavities Scope of delivery Blowmoulding machine | SIDEL | SBO 4/6 | 1992 Preform feeder Two types of molds for 1.5 L and 2.0 L bottles Cooling unit: RIEDEL

Overview  The machine was built in 2008 by the former manufacturer SIG Corpoplast (now KHS). The machine is still in operation and can be inspected at any time. Technical data Capacity: last 21.115 bph (at 1,5l)  Formats: 500ml, 750ml, 1.000ml, 1.500ml  PCO 1881  Operating voltage: 400V/ 50 Hz   Control voltage: 24 VDC  Scope of delivery  Blow molding machine | SIG Corpoplast | BLOMAX 12 | 2008  Preform feeder | Transver AG | - | 2008 Silo  Elevator  Sorting Chute

Diameter 1,220 mm (48") 1,480 rpm. 380/420 V 50 Hz max. temp. 40 °C 36 kWo

Unrenovated blown film line directly from production, make extruder Alpine HS 75 L/D 24, with 4 volumetric dosing stations, die head tool type BK 14-36 IBC, cooling ring HK 300 with peak, capacity up to 175 kg/h, film thicknesses variable depending on polymer, for HD-PE 12 ym – 50 my, corona treatment, film slitting knife, thickness measurement, film flattening, film widths 840 – 1,200 mm, tandem winder made by Kuhne, the technical equipment has improved over the years. Auch + Technik e. Kfm. D-73728 Esslingen Phone +0049 1577 5329827

Key data: 75 mm, 24

Blown film extruder for mono films TOP version Manufacturer Alpine BJ 1989 has already been partially modernized. Screw length 24d Screw diameter 75mm Blowing head BF 14-36 internal cooling from Alpine Cooling ring HK 300 with peak Output approx. 175 kg depending on the product Film thickness 12my – 50my Dosing Dosing unit with 4 volumetric feeders Winder Kuhne 1300mm Tandem Pre-treatment available 1 time Slotting device is available Flat laying 840mm – 1200mm Thickness measurement is available

23 blow moulds for the production of bottles Bottle volume 100 ml to 2 liters German manufacturer, good condition Complete list with all dimensions available!