127,561 used machines on RESALE, but how to find them? Machine Search
Material type: LDPE, LLDPE, mLLDPE, HDPE, PP, regranulates Machine dimensions (LxWxH): 16 X 5 X 10.5 m Min/Max final Film width: 900 / 1700 mm Film thickness: 27–200 μm Capacity: Up to 240 kg/h Line speed: 0–150 m/min Screw diameter: 55/65/55 Layer ratio: Up to 25/50/25 % L/D ratio: 30/1 Number of heating zones: 3 for 55 mm and 4 for 65 mm (1 zone per screen) Dosing system: Doteco Grado; 3 units with 4 components each; centralized vacuum pump (added later); all scales fully serviced last year; new software and external touch screen; neck (before extruder) with additional magnets Electronics: Siemens, ABB Software: Macchi's; full control via touch screen (replaced 3–4 years ago) Die head with IBC: 280 mm; 2.4 mm gap (3 heating zones); TE502 model with air ring extension Internal cooling balloon diameter control (IBC) Ultrasonic sensor (1 unit); JET ...
Subject to prior sale - errors possible! Internal reference number: D-1143-7
Souffleuse MECCANOPLASTICA MP1 - D En bon état de fonctionnement Année 2000 2 postes Force de fermeture : 35 KN Volume max du contenant. : 1,5 litres Diamètre vis. : 60 mm
used
We offer a refurbished rotary lobe blower Brand: Robuschi Type: K 150 All our refurbished blowers are equipped with new bearings and sealing elements. If you have any questions, please feel free to call.
We offer a refurbished rotary lobe blower Brand: Kaeser Type: Omega 63 Plus All our refurbished blowers are equipped with new bearings and sealing elements. If you have any questions, please feel free to call.
plate width: 2000 mm sheet thickness - max.: 10 mm sheet thickness - min.: 3 mm number of straightening: 13 Rollers straightening roll diameter: 145 mm straightening feed: 16 m/min bale length: 2330 mm distance b/n rollers centers: 150 mm diameter of bottom rollers: 290 mm main drive motor: 30 kW weight: 32 t - number of bottom rollers: 21/24 - Number of supports (top/bottom): 3 /3 - speedof adjustm. of traverse: 0,71 mm / sec - way oftraverse: -18 mm to +42 mm - max. swivellower traverse: 8 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
MACHINE À INJECTION - SOUFFLAGE PROCREA TYPE Rev 100 Cette machine d’injection soufflage PROCREA REV 100 peut produire des récipients à corps creux complètement finis, sans déchets comme moulés en injection avec différentes matières plastiques, avec des cycles complètement automatique, capacité de 5 cc. à 750 cc. et poids de 5 gr. à 100 gr. Cette machine est prédisposée pour fonctionner avec des moules de 1 à 4 empreintes et la production est très élevée grâce au système à revolver qui accomplit toutes les opérations d'injection, soufflage et éjection de la pièce finie dans un seul stade. La construction des moules pour la Rev 100 est très simple grâce au système automatique d'extraction appliqué au revolver.
A Robuschi (Gardner Denver) blower including a rotary valve and spare blower is available. Intake volume: 403m³/h, differential pressure: 300mbar, temperature increase: 35°C, power: 5kW, speed: 3900rpm, efficiency: 84.8%, motor power: 11kW. Includes Zeppelin AG11 rotary valve and replacement blower. Documentation available. On-site viewing possible.
used
GENERAL DESCRIPTION: The Macchi 3-Layers E18 is a high-capacity blown film co-extrusion line intended for production of general-purpose films with high width and output demands. It processes LLDPE, LDPE, mLLDPE, MDPE, HDPE, and in upgrade configuration also PP. The system uses a 700 mm 3-layer die head and reaches an output capacity of up to 900 kg/hour, depending on formulation. EXTRUSION GROUP: • Extruders: 80 mm + 100 mm + 80 mm • Infrared heating • Hydraulic screen changers Detailed upgrade specification: • One extruder Plastex 100/30D (middle layer B) • Two extruders Plastex 80/30D (layers A and C) • Bimetallic barrels • Nitrided screws • Water-cooled grooved feeding sections • 5 heating zones with IR heaters and blowers •Engine: - 150 kW DC motor (100 mm extruder) - 100 kW DC motors (80 mm extruders) • AC motor application with digital control ...
material width: 250 mm material thickness: 2 mm diameter: 1200 mm total power requirement: kW weight of the machine ca.: t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Manufacturer: Kautex Model: KBS2-20/40-S90/22D Year of Manufacture: 1999 PLC control: Siemens S5 Grinder: Rapid 3545 Conveyor Material feeding system Piovan Dedusting system Piovan Automatic component gripper and scale Spare parts Control Voltage: - AC: 230 V - DC: 24 V Working Voltage (AC, 3-phase): - Drive I: 400 V - Drive II: 400 V - Heating: 400 V Frequency: 50 Hz Rated Current: - Drive I: 285 A - Heating: 70 A Maximum Fuse Rating: - Drive I: 315 A (time delay) - Heating: 100 A (fast acting) Find more here - / Contact us at -
Radial duct fan for easy, direct installation in the sewer system. Housing made of galvanized sheet steel. Rated Voltage: 400V Frequency: 50Hz Phase(s): 3~ Power consumption: 1,246W Current: 2.25A Speed: 1,315 r.p.m. Volume flow: max. ; 3,168; m³/h Minimum pressure, static: 250Pa Max. conveying device temperature: max. 40°C Max. conveying device temperature at speed control: 40°C Sound pressure level in 3m: 57dB(A) Degree of protection, motor: IP44 Weight: 31 kg Rectangular channel connection, height at inlet & outlet: 300 x 600mm
material width: 0200 mm material thickness: 3,00 mm no. of straightening rolls: 21 sheet thickness - min.: 0,50 mm diam. of the rolls ca.: 30 mm speed: 56 m/min total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Hydraulic drive All rollers driven Side belt guide with handwheel PSS300 control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
PET blow moulder SIDEL SBO 18 The machine was upgraded in 2006 with a new program for an output of 26,500 bph. The machine includes preform tippers for 2 octabins each. Preform steep conveyor to the inlet into the machine.
Blowing machine SIPA type SFR EVO3 capacity: 18.000 bph - 0,5 ltr., 1,0 ltr., 1,5 ltr. year of manufacturing: 2017 neck type: PCO 28 - 1810 with 8 cavities incl. preform feeding system incl. preform cooling system Min. - Max. bottle diameter (diagonal): 50 - 125 mm Min. - Max. bottle height (without neck): 80 - 349 mm without high pressure compressor The machine is still in production until the beginning of February 2026.
Key data: 2 mm, 10 mm
Sheet Straightener 2,000 x 10 mm Execution.. 4high Blechdicje . 3-10 mm Straightening rollers.. 13 pcs. Straightening rollers durcm.. 145 mm Support rollers Duchm 290 mm Weight... 32,000 kg Drive mot... 30 KW
Souffleuse PLASTIBLOW type PB1 E/S électrique 1 tete , 1 poste Diamètre vis : 50 mm Année : 2008 Volume du flacon max : 1 litre Force de fermeture : 35 KN Cadence à vide : 1,5 sec Rapport L/D : 25 Consommation moyenne : 5 KW/h Puissance moteur : 18 KW Puissance de chauffe. : 6,9 KW 4 zones de chauffe 3 ventilateurs Dimensions moule : 280 mm x 325 mm x (81 + 130 + 85 ) mm Dimensions machine ( L x l x H ) : 2,35 m x 3,80 m x 2,35 m Poids : 3650 KG
Blowing machine SIG Corpoplast type Blomax 20 capacity: approx. 30.000 bph year of manufacturing: 2002 min. bottle volume: 200 ml max. bottle volume: 3.000 ml max. bottle diameter: 126 mm max. bottle length: 350 mm min. bottle length: 107 mm incl. preform tipper incl. preform feeding system neck size: PCO 28 incl. spare part package
Key data: 65 mm
Qty. 1 Second-hand 3-Layer Co-Extruder Line Brand & Model: MACCHI 3-layer co-extruder Built: 2012 Materials to be processed: LLDPE/LDPE/LLD/HDPE Extruders: 65 mm + 80 mm + 65 mm Infrared heaters 3 pcs plate filters Head: 3 Layer blown film Die head TE5303-IBC-350/500 Dies diameter 350 and 400 mm IBC Die Gap: 1.8 mm Output: Up to 800 kg/hour depending on material formulation Air ring: Dual flow air ring carbon fibre Take off: Take off 2400 mm wide Oscillating nips Motorised side gusseting Rewind: Double winder, fully automatic back-to-back rewinder Winder, fully automatic roll change Reels diameter up to 800 mm Winding width 2350 mm Accessories: Tower Web guide E&L Components blander Shini Gravimetric weight control system Piovan/Doteco Dosing units Doteco Automatic Thickness control Kundig/K-Design Profile gauge control system Calibrating basket Corona-treat ...
Souffleuse MECCANOPLASTICA type MP1 - D En très bon état de fonctionnement Année : 2001 1 tete double et 2 postes Controleur de paraison 64 point MOOG Force de fermeture : 35 KN - 3500 kg Volume max du contenant. : 1,5 litres Diamètre vis : 60 mm 4 ventilateurs de refroidissement Puissance maximale de chauffe : 20 KW
BATTENFELD FISCHER BEKB 175 T blow molding machine - 29 kg of PE - 300 liters BATTENFELD blow-moulding machine capable of extruding parts up to 4500 mm. Machine equipped with a 40-liter accumulation head. HDPE capacity: 28.8 KG Closing force: 2 x 175 T with knee-bar locking system Machine equipped with 2 x 125 mm screws (20/D ratio) Capacity: 149 KG / H at 25 RPM Max screw speed: 40 RPM Blowing pressure: 7.5 bar (12-bar compressor available if required) 3-material volumetric screw dosing system (virgin material, regrind and colorant) Machine equipped with unloading clamp Can be sold with a RAPID GK 8045 shredder Machine sold with a 260 mm diameter die and a 300 mm die. It is possible to equip this machine with a 500 mm die.
The Mapro Positive Displacement Blower consist basically of a pair of Tri-lobe rotors, mounted on parallel shafts, rotating in opposite directions inside a properly shaped casing closed at the ends by side plates. The two Tri-lobe rotors are synchronized by a pair of timing gears. As the rotors rotate, air is drawn into the inlet side of the casing, is moved from the inlet to the outlet side by the free volumes, between rotors and stator and finally is forced out of the outlet side against the connected system pressure. The blower does not develop pressure within the casing but the discharge pressure depends only upon the connected system resistance. Motor: 15 kW - 400 V - 50 Hz - 2.950 rpm - 27,1 A. P(inlet): 1.013 hPa. P(outlet): 300 hPa. PS: 620 hPa. T amb: 20/40 °C. Blower speed: 2.500 rpm. Q: 228 cfm. Sound level: 87 dB(A)., Type of Machine: Positive displacement blower, Stock Numb ...
High pressure radial fan, dust extraction fan, exhaust gas extraction, welding fume extraction, extraction, fan, pressure blower, vacuum blower, radial blower, high pressure blower -Manufacturer: Spelleken, high pressure blower type VRU-15-100-30H 1 -Drive motor: Holder 3 kW -Speed: 1430 rpm -Volume output: 0.25 m³/s -Pressure pt: 49.5 mbar -Connection input: Ø 105 mm -Connection output: Ø 105 mm -Bolt circle: Ø 180 mm -Dimensions: 900/510/H910 mm -Weight: 81 kg
High-pressure radial fan, dust extraction fan, exhaust gas extraction, heating fan, welding fume extraction, extraction, fan, pressure blower, vacuum blower -Exhaust gas exhaust fan -E-motor: Lammers 400/690 V/3 kW -Fan: Hansa Ventilatorenbau Type BC 280-5/4K-X/UX 1101 -Speed: 3179 rpm -Volume output: 2160 m³/h -Connection input: Ø 735 mm -Connection output: 365 x 310 mm -Dimensions: 1300/740/H820 mm -Weight: 153 kg
High pressure radial fan, dust extractor fan, exhaust gas extractor, welding smoke extractor, extractor fan, pressure fan, vacuum fan, ventilation fan -Motor power: 0.64 kW -Volume output: approx. 45 m³/min -Connection air duct: 285 x 140 mm -Number: 2x fan available -Price: per piece -Dimensions: 390/340/H340 mm -Weight: 12 kg
radial fan, dust extraction blower, fan, extraction, dust blower -Motor power: 1.1 kW -Speed: 2810 rpm -Max. volume flow: m³/h -Max. pressure: Pa -Inlet connection: Ø 300 mm -Outlet connection: Ø 290 mm -Impeller: Ø mm -Number: 2 fans available -Price: per piece -Dimensions: 970/770/H660 mm -Weight: 46 kg
High-pressure radial fan, dust extractor fan, exhaust gas extractor, welding smoke extractor, extractor, fan, pressure fan, vacuum fan -Motor power: 1.1 kW -Speed: 2870 rpm -Volume output: m³/h -Pressure increase: Pa -Connection inlet: Ø 270 mm (without nozzle) -Connection output: 100 x 140 mm -Number: 1x fan available -Price: per piece -Dimensions: 540/400/H775 mm -Weight: 40.5 kg
High-pressure radial fan, dust extraction blower, exhaust gas extraction, welding fume extraction, extraction, fan, pressure blower, vacuum blower -Engine power: 0.12 kW -Speed: 2780 rpm -Volume output: 252 m³/h -Pressure increase: 240 Pa -Inlet connection: Ø 142 mm -Output connection: 56 x 52 mm -Quantity: 1x blower available Price: per piece -Dimensions: 270/180/H160 mm -Weight: 4.8 kg
High-pressure radial fan, dust extractor, exhaust gas extractor, welding smoke extractor, extractor, fan, pressure fan, vacuum fan, ventilation fan -Motor power: 0.56 kW -Volume output: approx. 45 m³/min -Connection air duct: 285 x 150 mm -Number: 2x fan available -Price: per piece -Dimensions: 380/380/H330 mm -Weight: 15 kg
radial fan, dust extraction blower, fan, extraction, dust blower -Engine power: 3.6 kW -Speed: 1440 rpm -Volume flow rate: m³/h -Inlet connection: Ø 450 mm -Outlet connection: Ø 450 mm -Impeller: Ø 670 mm -Quantity: 1 available -Dimensions: 1200/1100/H1350 mm -Weight: 242 kg
High-pressure radial fan, dust extractor fan, exhaust gas extractor, heating fan, welding smoke extractor, extractor, fan, pressure fan, vacuum fan -Motor power: 1.1 kW -Speed: 820 rpm -Volume output: m³/min -Pressure increase mmWS -Connection input: Ø 250 mm -Connection output: 355 x 355 mm -Number: 1x fan available -Price: per piece -Dimensions: 440/490/H575 mm -Weight: 34 kg
Blowing machine KRONES Contiform S 8 year of manufacturing: 2003 capacity: 14.000 bph neck size: PCO 28 - 1881 Bottle size: 1,5 ltr. PET bottle incl. cooling unit incl. preform feeding system incl. preform container incl. preform tilting device air conveyor system is available immediately available in Germany The machine is in a good condition.
High-pressure radial fan, dust extractor fan, exhaust gas extractor, welding smoke extractor, extractor, fan, pressure fan, vacuum fan -Motor power: 1.1 kW -Speed: 2800 rpm -Volume output: 35 m³/min -Pressure increase: 95 mm water column -Connection input: 200 mm -Connection output: 105 x 120 mm -Number: 1x fan available -Price: per piece -Dimensions: 340/390/H470 mm -Weight: 18 kg
High-pressure radial fan, dust extractor fan, exhaust gas extractor, welding smoke extractor, extractor, fan, pressure fan, vacuum fan -Motor power: 0.45 kW -Speed: 2800 rpm -Volume output: 22 m³/min -Pressure increase: kPA -Connection input: 140 mm -Connection output: 110 x 110 mm -Number: 1x fan available -Price: per piece -Dimensions: 300/290/H360 mm -Weight: 12 kg
High-pressure radial fan, dust extractor fan, exhaust gas extractor, welding smoke extractor, extractor, fan, pressure fan, vacuum fan -Motor power: 1.5 kW -Speed: 2820 rpm -Volume output: 45 m³/min -Pressure increase: kPA -Connection input: 250 mm -Connection output: 170 x 150 mm -Number: 1x fan available -Dimensions: 420/395/H540 mm -Weight: 24 kg
High-pressure radial fan, dust extractor fan, exhaust gas extractor, welding smoke extractor, extractor, fan, pressure fan, vacuum fan -Motor power: 0.7 kW -Speed: 2750 rpm -Volume output: 20 m³/min -Pressure increase: 110 kPA -Connection input: 150 mm -Connection output: 110 x 110 mm -Number: 1x fan available -Price: per piece -Dimensions: 285/290/H360 mm -Weight: 10 kg
Dust extraction fan, exhaust gas extraction, welding fume extraction, extraction, fan, pressure blower, vacuum blower -Aggregates: come from UV paint drying -Motor power: 0.155 kW -Speed: 1400 rpm -Volume output: 18.5 m³/min -Pressure increase: 220 PA -Connection input: Ø 140 mm -Connection output: 100 mm -Quantity: 3x blowers available -Price per piece -Dimensions: 380/350/H260 mm -Weight: 8.2kg
Blow molding machine Kosme model: KSB 6R with 6 cavities year of manufacturing: 2017 neck size: PCO 1881 capacity: 12.000 bph container size: max. 3,0 ltr. including preform feeding system including chiller without blowing moulds already dismantled at the end of January 2026
radial fan, dust extraction blower, fan, extraction, dust blower -Motor power: 0.6 kW -Speed: 2800 rpm -Volume flow rate: m³/h -Pressure: Pa -Inlet connection: Ø 150 mm -Output connection: 150 x 110 mm -Impeller: Ø 260 mm -Number: 1x fan available Price: per piece -Dimensions: 450/400/H390 mm -Weight: 19 kg
radial fan, dust extraction blower, fan, extraction, dust blower -for: paint wall, paint booth -Motor: Explosion-proof -Engine power: 5.0 kW -Speed: 1455 rpm -Inlet connection: Ø 430 mm -Outlet connection: Ø 450 mm -Impeller: Ø 660 mm -Dimensions: 1350/900/H1240 mm -Weight: 236 kg
High-pressure radial fan, dust extraction fan, exhaust gas extraction, welding fume extraction, extraction, fan, pressure blower, vacuum blower -Engine power: 11 kW -Density: 1.2 kg/m³ -Volume output: 84 m³/min -Pressure increase: 3800 Pa -Connection input: Ø 275 mm -Connection output: Ø 270 x 130 mm -Dimensions: 1000/800/H700 mm -Weight: 252 kg
radial fan, dust extraction blower, fan, extraction, dust blower, blower, exhaust fan -Manufacturer: Nedermans, Dust extraction blower exhaust fan 500725 -Motor: 0.37 kW 3000 rpm -Fan wheel: Ø 290 mm -Connection: Inlet Ø 130 mm -Connection: Output Ø 120 mm -Dimensions: 540/420/H520 mm -Weight: 24 kg
maximum number of results exceeded
please refine your search
