pellet extruder used for sale

Koller head with 5 wheels, used

For sale is a used pelletizing line that has pelletized fertilizers based on wood fibers with cattle manure and fermentation residues in the last 4 years (approx. 5,000 h in total). Various well-known manufacturers are installed such as Amandus KAHL pellet mill / continuous mixer, Bühler hammer mill / conditioner, CPM pellet cooler, Wynveen pellet screen, Rako / Apullma conveyor technology Achievement: 1. Wood chips with cattle manure, dried approx. 1.5 t/h 2. dried, separated compost / dried digestate approx. 2.5 t/h 3. According to the manufacturer KAHL, the press can produce up to 3 t/h in the biomass Since the customer is now converting his business, it is for sale. In principle, the aim is to sell the entire line, a partial sale of the components is also possible by arrangement. The main components are: -Conveyor - Grinding: Hammer mill with screen drum, 2-fold ma ...

CENTRIFUGAL DRYER for pellets (to go with an existing pelletizer), for a 350/400 kg/h capacity of PE PP ABS PS PC flakes, made of sturdy AISI304 stainless steel with vertical axis, driven by a 2.2 kW 3 Ph.asynchronous motor,, complete with soundproofed discharge cyclone, stainless steel tank for water recovery and recycling, 1.1 kW water ump,, equipped with drainage for overflowing, HEAT EXCHANGER GROUP, made of painted carbon steel, internal copper tube bundle, with removable head to facilitate cleaning, fixed to the tank using brackets, float with water replenishment valve, Electrical board of machine wiring, Users manual, CE compliance, installed power - used power in work: about 60-65% : 2.2, conditions: new machine, type: for granulate - this machine goes after the pelletizer, capacity: 300-450 kg/h

TECNOVA RECYCLING EXTRUDER for BIO - PE PP ABS PC PS, Barrel with 90 mm screw diam. 37 L/D, Crammed feeding unit, Is working with BIO at 70 rpm yielding 270 kg/h, with PE at 100 rpm yelds 120 kg/h, N.1 degassing point, hydraulic screenchanger, water ring pelletizer from Gamma Meccanica, drying centrifuge, rotating classifier, electric cabinet for omplete management of the line, availability: 4 weeks for reconditioning or 1 week for AS IS, capacity: 120-270 kg/h, conditions: reconditioned, type: 90 mm. crammed feeder for light scraps

SCREW : 100MM MOTOR : 45 KW REDUCER : ZLY250 SPEED : 250 250KGS/HOUR REMARKS : 1)WOODEN CASE PACKAGE 2)NOT INCLUDE INSTALLATION COST 3)SINGLE SCREW EXTRUDER (1 PCS) 4)MOULD (1 PCS) 5)COOLING FLUME (1 PCS) 6)DRY MACHINE (1 UNI) 7)ELECTRICAL CHANGE NET SYSTEM (1 UNI) 8)PELLETIZER (1 UNI) 9) high temperature wire (FOC 30 m) Pelletizing Auto Pusher + Conveyor #1

Industrial pellet press manufactured by Bühler, model DPUC, designed for the continuous production of pellets from different raw materials. The equipment incorporates a 6 mm die and is prepared for a capacity of approximately 2.5 tons per hour, depending on the product and process conditions. The press is equipped with a roller compression chamber, conditioner for product pre-treatment and support bed. The assembly is complemented by a stainless steel worm conveyor, intended for feeding or evacuating the product in the pelletizing line. Technical characteristics DPUC Model Year of manufacture 2005 Production 2,500 Kg/h In your state

Münch RMP 660 pellet press for the production of wood pellets and biomass pellets from sawdust, wood shavings and other organic waste materials. The machine is suitable for industrial pellet production, offering high pressing capacity and consistent pellet quality. Ideal for wood processors, sawmills and biomass plants. Technical data: Screen: 6 mm Motor: 2 x 90 kW Inner diameter of die: approx. 660 mm Number of press rollers: 2 Pressing capacity: up to approx. 3–5 t/h Condition: Gebraucht Location: Tauberbischofsheim, Germany

Motor Power 200 kw Dics diameter 6 mm Used for wood pellet production Can be inspected under power

Pellet mill for straw / hay / alfalfa and much more ! Plant is about 500 hours. Running . Flat die 8mm and Koller head are included '

3 × AMANDUS KAHL 65-1500 Flat Die Pellet Mill – NEW 2025, in original crates Three brand-new AMANDUS KAHL 65-1500 pellet mills (2025), never installed, still in original factory crates. Ready for immediate delivery from Istanbul, Turkey. Kahl’s flagship and the largest flat die pellet mill on the market: up to 12 t/h per mill, up to ~36 t/h for all three. The mills come from a cancelled project and are offered at an attractive price well below the factory price. Package includes: 3 complete pellet mills with hydraulic, lubrication and oil systems EAPR automatic press control with 3 switch cabinets and remote maintenance 12 flat dies 1500 × 100 mm (9 × 8 mm, 3 × 10 mm) 72 pan grinder rollers, 18 breaking arms with knives Technical documentation (EN/TR) Technical data: die diameter 1500 mm, 630 kW drive, 10–12 t/h per mill. Suitable for wood, biomass, straw and gre ...

Content 136 m3, equipped with release ramp with chain hoist, size 5000x5000x7300 mm. Please note! This lot is part of a combination lot. Namely lot 22. Auction-ID: A1-51255-12

315 kW/450 hp, 1500 rpm, reading hours 816, equipped with receiving hopper with jacks. Equipped with digital Pro-face touchscreen/HMI. Total dimensions approximately 1600x4160x7300mm. Please note! This lot is part of a combination lot. Namely lot 21. Auction-ID: A1-51255-3

12 pieces ring dies Paladin 2400 CAV for pelletizing mill Andritz type Paladin 2400-250/ 2R BM Perforation 16/22 mm Pockets milled out for special rolls Material X46Cr13 unused = new Price per unit net ex location 6,250,-- € + VAT Sale from BL Brandenburg Code Q17

Extruder 70 mm - 24 L/D with pipe head up to 63 mm, calibration tank 6000 mm Caterpillar extractor, saw

Roller die line consisting of:- 1 x Troester 200mm pin barrel extruder Type QSM200K-16D power roller feed, 10 rows of 8 pins, L/D ratio 16:1 Serial no. 1816/88, year 1988, With temperature regulation unit, 282kW ASEA DC variable speed motor mounted on rails (moves away from calender to clean out etc) Hydraulic sheeting head linked directly to:- 1 x Adamson 24in dia x 68in wide two roll calender, peripherally drilled rolls cross axis, bush type bearings, motorised nip adjustment with unidrive gearbox 277kW ASEA DC variable speed motor Hydraulic clamping device for extruder Set of 4 x cooling drums Dual wind up and liner applicator Chalking Unit Siemens PLC control. Complete line in excellent condition. PRICE: On request.

Troester 150mm dia PIN extruder Type: QSM150K, Serial no. 8622/80, Year of manufacture: 1980, but refurbished by Troester 2000 (new screw and barrel section) Power roller feed, L/D ratio 16:1 8 rows of 8 pins, fitted with ASEA 212kW DC variable speed motor and controls (1800rpm). Complete with controls etc and in very good condition.

1 x David Bridge 15/18\ Dump Extruder with 40\ Face x 20\ die Roller Die. Spare parts available. Screw L/D 5:1, Crammer. Length of Barrel 7ft. Right angle turning unit for product flow. 200HP DC variable speed motor

Kobelco Twin Screw Roller Head Extruder (horizontal type), Model TSR-330 Roller die assembly (TSR-33H005H) 38in wide x 16in dia Roller die moves away from the extruder/mixer section via hydraulic ram. driven by 102kW DC variable speed motor through Hansen reduction gearbox (on flexible coupling so roller die can move forwards/back). Twin screw dump extruder 330mm screw dia driven by 90kW DC variable speed motor through Hanson reduction gearbox. In very good condition. Previously running underneath an F270 Banbury. Complete with all controls, manuals and documentation etc.

We´re offereing successfully since many years twin-screw compounding extruders >> NEW segmented screws and cylinders, LD ratio due to your request Side-feeders, vacuum ports and accessories Please contact us for further information

Francis Shaw 18/22\ Dump Extruder, Crammer feed Length of Screw 9ft 6\. Reliance 400hp D.C., 1150 r.p.m., 480 volt. Large Hopper/Chute to next floor level.

1 x Werner & Pfleiderer 400mm dia dump extruder, Type: EAE400, Fabrik nr 221284, Werk nr 416295, Year: 1985, double hydraulic crammer feed, feed section 965mm wide, L/D ratio 8:1, with 235kW DC variable speed motor, Sheeting head to produce up to 1000mm wide sheet. Complete with controls and hydraulics etc.

Used EXTRUDER twin screw (TWIN SCREW EXTRUDER) for the production of cereal flakes: Producer: PAVAN Model: TT92 Year: 2002 Dimensions: 6580 x 4150 x 3000 Weight: 2400 kg Productivity: 500 kg / h Power: Description: A twin-screw extrusion device as a result of a continuous and automatic process of a great variety of flour and cereal starches / tubers, both mixed and pure. The materials from the dispensing unit are pre-mixed using a suitable device equipped with counter-rotating blades (double shaft mixer), and then enter the mixing tank for kneading and homogenization. From the mixing tank, through a suitable screw device (forced supply), the mixture is pressed into a group of cooking cylinders in which the cylinders are heated to the desired stage, according to a predefined and automatically controlled temperature profile. compatibility of extruder screws, which are repla ...

1 x Francis Shaw 45mm dia coldfeed rubber extruder, M/c no. 4513, Year: 1992, power roll feed, L/D ratio 15:1, hinged straight head with c\clamp, cored scred + jacketed barrel with built in temp control unit. Complete with control panel and in very good condition. Box of dies included.

Iddon Cold Feed Extruder. 2.5" screw dia. 10/1 LD Ratio. Motor Size 20.4/5.5 HP

Multiple extruders

Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.

Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

Key data: 100 , 140

Stock No.2452 1 used, partially overhauled and functionally tested pelletizing line Throughput up to 500 kg/h depending on the material, consisting of: Tamping unit Kreyenborg SW 100, drive 7.5 kW Extruder BKG single screw Ø 100 mm – 35 LD, Drive 132 kW – AC frequency controlled Screw speed up to 143 rpm.-1 screw depth 14 mm Heating capacity approx. 35 kW installed 1x athm. Degassing zone Screen-pack-changer Double piston Kreyenborg K-SWE 160 RS back-flush self-cleaning with screen surface 244 cm² BKG underwater pelletizer AH 300, complete with: Start-up valve incl. Hydraulic station Granulator with drive 4 kW Water pump 2.2 kW By-pass system, water tank with heating 9 kW installed and heat exchanger BKG granulate centrifuge TWE 300 with drive 3 kW pellet classifier table Control board and Siemens material feed conveying, big-bag filling station � ...

1 x Buss PR200? Ko-Kneader, supplied fully refurbished by Buss in 1995, G130 gearbox, 11 L/D ratio, with 340kW dc motor and controls. Including oil heater and TCU 2t/hr output. Spare screw and barrel segments.

1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.

Key data: 30 , 28 , 110

Plant for the production of filament for use in 3D printers Capacity up to 10 kg/h consisting of 30 mm extruder, stainless steel trough, puller and winder with traverse guide

Key data: 30 , 28 , 110

Single-screw extruder with new 7,5kW drive, new gear box, new cylinder and new screw 30 mm - 28 d, nitrated new ceramic heating elements, cooling fan, temperature sensors Control cabinet integrated in the machine frame Machine frame on wheels Stainless steel hopper

According to the description below

Extruder KE 90 x 30-D for manufacturing of von TPE foam and compact profiles screw diameter: 90 mm L/D ratio 30:1 (2700mm) extruder with 11 temperature-controlled zones (electrically heated by fluids) Siemens electric drive, motor 45kW at 2500rpm year of construction 1996, machine in very good condition (preliminary used in test operations) melt application device (gear pump) double profil head (also used for extrusion-coaded framework belts) electric equipment partially available extruder mounted on movable baseplate

Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.

Extruder Petersen VAP 65

Nordson / Puffe Extruder Plant Ex20 -1xPS01-1xPE20-1 for melting hot melt adhesives and thermoplastics, feeding as granules. Melting capacity according to the manufacturer's specifications up to 20 litres/h (EX20) Price: 45.000, -- € plus 19% VAT (Gross price incl. VAT 53.550, -- €) EXW Manufacturer: Nordson / W. Puffe Hotmelt-Technology Model No.: Ex20 -1xPS01-1xPE20-1 Year of manufacture: 05/2006 Serial No. 226260231/001 Power: 15 kW, connection 380V three-phase current Emergency stop, traffic light, CE mark Made in Germany Compact system mounted on a stable rolling frame (H= 198 cm, W= 160 cm, D= 110 cm) consisting of Nordson extruder, gear metering pump, Lenze worm drive, control cabinet with Allen-Bradley control, graphical user interface, storage tank, operating manual. Auxiliary: Labotec Minifeed Suction Conveyor MF60 Serial No. 12-103-00669 (Owner's man ...

Industrieöfen- Fertigung und zirlguss Reparatur jeglicher Art Wartung und Einregulierung von Industriebrennern Industrieöfen für Öl, Gas oder elektrisch beheizt Umfangreichen Sortiments an Feuerfeststeinen, Feuerfestmassen, Isoliermaterialen und Gießereihilfsstoffe namhafter Hersteller. Renovierungen und Instandsetzungen von Ofenanlagen Brenner einstellungen von Ofenanlagen schoenheider Modernisierungen von Ofensteuerungen Umrüstu ng von elektrischen Öfen auf gasbeheizte Öfen Umrüstung alter Heizsysteme auf Rekuperation gienanth Öfen Verzinkungsofen Ve rgüteofen Anlassofen Industrieöfen Glühofen Ovens laboratory ovens industrial furnaces industrial furnace plants Industrial Furnaces high-temperature chamber furnaces hardening furnace anlageHärteöfen Annealing furnaces Conveyor belt Abg aswäscher Abkühlungsöfen Abwärmerückgewinnung Aluminiumgiessereimaschinen ...

Key data: 150 mm

Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg

EXTRUDER

Drive : 12 KW

T-Die Serial No.: L 1081-041391 // Calender Serial No.: F 1201-041392 Haul-Off Serial No.: F 1201-041392-T Max. winder speed: 50 m/min Type: Film system 1080 mm usable width Equipment / Additional information: Max. gross output PP up to 1000kg/h with film width up to 1200mm A special feature is the winding system, which can cut narrow films (150 mm - 100 mm) or for example 8 x 175 mm or even 2 x 700 mm one nozzle lip with a max. film thickness of 2mm up to 1000kg/h. Total power consumption: 211 kW/h Main engine power: 250 kW Min. 068 mm film thickness in PS / min. 0.75 mm in PP Maximum calender speed: Max. 50 m/min. mechanically possible Consists of: -Dosing system 5-chamber Maguire -Extruder (160 mm screw) Amut EA 160 // Age: 2003 -Screen changer (for cleaning in food production) -Melt pump -Slot die (1 insert) 120 cm -Lip with max. film thickness up to 2mm up to 1 ...

Material: PE, PP, PS, ABS / Details: DC motor 220 kW, degassing, dcrunner, screw diameter 70 mm, LD: 32, Throughput: approx. 400 - 600 KG/hr.

We have for sale little used Hunan Fumach Twin screw extruder. This extruder has undergone a complete overhaul where all electrical wiring has been refurbished, ABB motors, Siemens logic, etc. The modification work has been done in Finland and the modifications have been given the CE mark. The extruder meets all the directives required by the EU Twin-screw Extruder FMHE72 which can be used for processing cereals, snack food, Nutrition, rice protein, reengineering, Starch gelatinization, caramel, rice products, pet food, Aquatic product feed, etc. Manufacturer: Hunan Fumach Foodstuff Engineering & tech. co. Ltd Type: FMHE-72-24 Year: 2017 Production capacity: 300-1200 kg/h Screw type: Twin screw, diameter 72 mm Screw length diameter ratio: 24D Screw rotation speed: 50—500r/min Screw torque: 2100N.M Oil pump motor: 1.1 kw Barrel temperature: -20-300℃ Die temperatu ...

Food Extruders single and twin screws for various applications : breakfast cereals, corn flake, pet food, full fat soya, snacks We overhaul many models and have in our stocks machines like Clextral BC 45/82, wenger 175 ... also walter single screw. Milin Gentieg cereals Britany, France processing equipments has been specialising for years. We organise deliveries to any destinations for single machines or complete lines from cleaning to flaking and extrusion

Extruder Rieter SP 650/600

EDI Autoflex Extrusion Die width 900 mm.

Farrel Twin Screw / Rollerdie Extruder complete available with Motor and Inverter Description attached!

Barwell Hydraulic Extruder – Used For sale: a used Barwell hydraulic extruder, designed for processing rubber compounds and elastomers. Barwell machines are well known worldwide for their robust construction, reliability, and consistent performance in industrial applications. The machine has been operated in an industrial environment, regularly maintained, and remains in good technical condition. Ready for further use after installation. Key features and advantages: Hydraulic drive ensuring smooth, stable, and precise extrusion Heavy-duty, solid construction for long service life Reliable operation, even with demanding rubber compounds User-friendly operation and easy integration into existing production lines Proven Barwell quality, widely trusted in the rubber industry Applications: Extrusion of rubber profiles and semi-finished products Preparation o ...