126,693 used machines on RESALE, but how to find them? Machine Search
Offer via gebr. outdated - pipe separation and chamfering machine Fabr. GF Type RA4 Saw has been completely overhauled and tested. - Engine re-stored and new seal. - Gearbox re-stored and new seals Technical data: Outer pipe diameter 15-120mm Wall thickness 1 - 10 mm Power connection 200 - 240 V / 50 Hz stepless speed 150 - 270 rpm. Speed levels electronically 1 - 6 Power 1600 W incl. mounting plate used, in good condition.
Offer via gebr. outdated pipe cutting and chamfering machine Fabr. GF GEORG FISCHER Type RA8 / RA230 Saw has been completely overhauled and tested. - completely new engine. - Gearbox re-stored and new seals Technical data: Outer pipe diameter 124-230mm (4" - 8") Wall thickness 1 - 10 mm Power connection 200 - 240 V / 50 Hz stepless speed 40 - 215 rpm. Speed levels electronically 1 - 6 Power 1800 W incl. mounting plate used, in good condition.
Offer via gebr. outdated - pipe separation and chamfering machine Fabr. GF Type RA6 Saw has been completely overhauled and tested. - Engine completely new - Gearbox re-stored and new seals Technical data: Outer pipe diameter 75-183mm Wall thickness 1 - 10 mm Power connection 200 - 240 V / 50 Hz stepless speed 40 - 215 rpm. Speed levels electronically 1 - 6 Power 1800 W incl. mounting plate used, in good condition.
used
Qty. 1 Second-hand JCO pipe press bending line Mfc.: Samyul, ROBO, Shinsung, ChangSong, Rotech, FANUC, Hyupshun, Ingersoll Built: 2003, 2008, 2009, 2013, 2014 Plate material: Mild steel Plate dim.: 16.0 x 5.2 x 0.08 m – L x W x T Pipe dia.: Φ400~Φ1650 mm Pipe Length: 6.0m ~ 16.0 m Scope of supply: JCO Hydraulic Press Tack Welder Machine Sealing Welder Pipe Heating & Rotating Device Inside Welder Outside Welder Calibration Presses Milling Cutter Cutting Machine Bevelling Machine Compressor
Double pipe heat exchanger pipe heat transfer for biogas plant, sewage treatment plant sludge hygienization - used - Manufacturer AEL GmbH Leisnig Type Double pipe heat transfer W202 Fabr. No. 7.0637.940/29-56 Built in 1997 Permissible betieb pressure 6 bar Permissible operating temperature 90°C Content 1090 l Kerb weight 6510 kg Length approx. 11 m Width approx. 3 m Depth approx. 1.5 m
Pipe screw, cement screw used without motor for the conveyance of cement or similar materials with directly attached bearings Total length: 6520 mm Screw aisle length: 6130 mm Screw aisle: 210 mm Shaft of 80 mm, slope progressive at the inlet Opening opposite the driven side: inside 210, flange 280 mm Opening 1 driven side: 250 mm Opening 2 (with lid) diameter: 200 mm Matching motor and overhaul can be offered optionally. Drive via flange motor with coupling
Hyundai RB Onsan Factory, located at Ulsan in South Korea produces welded pipes by means of LSAW – Longitudinal Submerged Arc Welding process. The line is offered complete, featuring advanced HAEUSLER (Switzerland) core equipment. This facility is capable of producing welded pipes with the following specifications: Diameter: 22 to 80 inches Thickness: 6.4 to 25.4 mm Length: 6,000 to 12,200 mm The production line is equipped with a comprehensive suite of machinery altogether ensuring seamless and efficient production of LSAW pipes, including: • Plate edge milling • 3-roll bending • Post bending • Tack welding • Inside welding • Outside welding • Copander • End facing • Pipe inside washing • Hydrostatic tester • X-ray • Semi-correction • Pipe roll conveyor with skid system
Pipe screw conveyor screw inclined conveyor without motor used Our own special machine construction can also be made. Pipe diameter approx. 260 mm Pipe length approx. 4780 mm Screw coil length approx. 4200 mm Inlet/outlet-diameter approx. 250 mm Screw tube top open with lid Price without engine We adapt the engine to their use at an additional cost. Ideal snail for wood chips or similar wood chips. Total approx. 5050 x 1000 x 600 mm 2 pieces available
Sell Steel pipes DN 1200 wall thickness 20 mm, outer PE sheathed and coated inside and elbows DN 1200 Steel pipes DN 1000 wall thickness 14.8 and 16.8 mm, outer PE coated and internal coated Elbows DN 1000 from 10 to 45°
Offer via gebr. Thread cutting machine with pipe saw RA21 Made GEORG FISCHER type KM2, built 1997 Technical data: Thread diameter 3/8" - 2" Power connection 200 - 240 V / 50 Hz With mobile undercarriage with threaded cutting jaws 3/8", 1/2", 3/4", 1", 11/4", 11/2",2" used, in good condition.
Pressure pipe ground MAN 40/54 recon MAN part number: 434.01.012
Exhaust water cooled Recon Part Number: 1206 7084 Attention: We also have various other RECON parts of different manufacturers / types available. We will be happy to send you our current stock list. ---------------------------------------------------------------------- ----------- Sale only to commercial customers! ---------------------------------------------------------------------- ------------ If you have any further questions, please do not hesitate to contact us!
used
Recon Part Number: 1231 4275 Attention: We also have various other RECON parts of different manufacturers / types available. We will be happy to send you our current stock list.
Qty. 1 Second-hand bifilar pipe winding line Mfc.: GRAEWE GmbH Type: AEW 1000 Built: 1998 Tube dia.: 10, 12, 14 & 16 mm Coil core ID: 940 mm OD: 1250 mm Bifilar coiler Type: EW 1000 PLC Simatic S5 Consist of: De-coiler Coiler Ring coiler Bending unit Support table Cutting shear Binding device Electrical Control
tube diameter: 50,8 mm wall strength: 1,0 mm square edge steel: 50 x 50 x 1 mm round bar steel: 25 x 6 mm weight of the machine ca.: 46 Kg dimensions: 0,6 x 0,4 x 0,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hilco Industrial is the selected partner by Hyundai RB to facilitate the sale of new LSAW Welded Pipe complete production lines as well as individual machinery, designed and manufactured by Hyundai RB (South Korea). Based on excellent production capacity achieved over more than 25 years’ experience, Hyundai RB developed its own S.A.W. pipe production lines featuring JCO Press Bending. LSAW Welded Pipe Production Line Main Equipment and features: Shot Blasting – Max 6m/min x width 4,800 Edge milling – Φ800 cutter type x 130kw – Quick tool changing – Max. milling speed: 6m/min. – Automatic calculation of number of milling – Automatic width checking Edge-Bending (Pre-Bending) – 1,500 ton/8t ~60t/6~13.5m – Quick size changing – Max. bending thick.: 60mm JCO Press Bending – 6,000/8,000/10,000 ton (max.13.5M) – PLC with CNC (Recipe memory) ...
Key data: 60
PE pipe extrusion line - 1-screw extruder: 60 mm Ø, 28 L/D with motor: 37 KW (50hp) with AC speed variator, electrical panel with tube head for 16 and 20 mm. - 3 m vacuum and cooling bathtub with vacuum pump: 5.5 hp. - Cooling bath: 2.5m - Drag trolley (Track): 800 x 100 with variable speed drive. - Minimum inner double coil winder: 330 Ø maximum external 1,200.
REMS MAGNUM 4010 LT pipe threading machine was built in 2020 in Germany by REMS GmbH & Co KG. This extremely versatile tool is designed for threading all kinds of pipe and bolt threads. The clamping chuck used prevents material slippage during machining, making the process very stable. The large distance between the clamping chuck and the centring chuck, in turn, allows long pipes to be clamped securely. After machining, the edges of the material are smoothed by an internal deburring device with two blades. The MAGNUM 4010 LT pipe threader on offer weighs approximately 80 kg. Technical specifications of the REMS MAGNUM 4010 LT pipe threading machine - thread types: R, NPT, G, NPSM, Pg, M, UNC, BSW - pipe thread diameter: 16-63 mm / ½ – 4″ - bolt thread diameter: 18-60 mm / ½ – 2″ - pipe thread length (cylindrical): 150 mm - bolt thread length: unlimited - spindle rotat ...
Tube range up to: 48,3x3,25mm (E235mitRm =2xD) Bending radius up to: 125 mm Control: electronic ( + known 4-fold bending angle preselection ) Bending angle maximum: 180° Bending speed: 20°/s Dimensions L / W / H: 2380 / 800 / 1250 mm Weight: approx. 650 kg Electr. Power: 2.4 kW incl. sawing unit with visualization of the saw position via line laser Deburring unit, drive unit for assembly attachments Tube positioning - length and twisting 2-axis positioning indicator, premature mandrel retraction Auto. Mandrel lubrication (minimum quantities) Interface for network connection and data import
: R10-R260 bending speed: 2,5 U/min : 42x3 mm : 42x2,5 mm : 30 mm : 54x2 mm total power requirement: 1,5 kW weight of the machine ca.: 80 kg dimensions of the machine ca.: 410x1000x570 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
1) Drill pipe BTA Ø 43 x 2700 - 20 pcs; 2) Drill pipe BTA Ø 26 x 2700 - 40 pcs; 3) Drill pipe BTA Ø 22 x 2700 - 24 pcs;
: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW weight: 450 kg range L-W-H: 1100x800x1500 mm Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - Footswitch - standard roller set The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
mandrel bending machine Tansfluid DB 628 Year of construction: year 1995 Drive power Drive power 1.5 kW Drive drive hydraulic cylinder & roller chain Pipe range bending type 4-28 mm Bending angle bending angle 190° (without tube) Bending radius bending radius 1.5 x D – 2.0 x D Nominal pressure nominal pressure 250 bar Operating pressure 3095 mm n. right. Flow rate delivery rate 4.5 l/min
Seam closer Schechtel MS Manual Length 1 m
Machine type: Kieserling seven-roll straightening machine Working range: Tubes from Ø 15 mm to Ø 75 mm Rods Ø 20 mm to Ø 65 mm Direction of passage: from right to left Speed: approx. 50 m/min Make Kieserling & Albrecht Type: WRUN 1A Location: Solingen Length 2,400 mm Width 2,000 mm Height 1,900 mm Weight 4,600 kg Country of origin: Germany
Machine type: Bronx six-roll straightener 6CR 4BW incl. saw and roller tables Working range: Tube: from Ø 15 mm to Ø 54 mm Make Bronx, similar to Kieserling, type: Bronx 6CR 4BW
Machine type: Two-roll straightening machine Working range: from Ø 4 mm to Ø 32 mm Direction: From left to right Speed: 24m/min Make Kieserling Type WRPF 20/30 Year of construction: Refurbished in 2023
Inv. Num. : 6907 Type: B/90 Producer: Curvatubi Generated:- Parameters: Tube diameter: 50-60 mm
Offer 23291 Specifications: End processing machine for pipes with six-fold turret - tool holder Tube diameter 6 - 40 mm Max. forming length 100 mm Drive 400 V / 7.5 kW Space requirement approx. W 1200 x D 2100 x H 1500 mm Weight approx. 1400 kg
Key data: 60
Composite Tube Extrusion Line: A- Extruder, brand: Sterling, 1 spindle: 60 mm Ø 25L/D, Motor: 25 hp with variable speed drive and electrical panel. B- Head for small tube: 0.5 mm and more. C- Water-cooled bathtub: 9 meters with pump and tank. D- Tow Cart, Brand: Mild Ltd Boston: 700x150, Motor Output: 1.5kw with variable speed drive. E- Double winder with guide: 600 mm Ø
Used pipetting robot Tecan EVO 150 with Tecan dongle and CDs and accessories .
Type of machine Bültmann Straightener Working range tubes: 10 - 60 mm Speed 10 - 120 m/min Make Bültmann , Type PRM 60/060 Location: Germany Working height approx. 1,500 mm Country of origin: Germany
Hamilton FLOW PCR Setup Instrument The Hamilton FLOW PCR Setup Instrument is a benchtop robotic workstation for fully automated preparation of PCR and qPCR reaction approaches, designed to minimize manual pipetting errors and increase sample throughput. It is typically used in conjunction with Roche Life Science products (such as the MagNA Pure 96 System and LightCycler® 480 Instrument) as part of the FLOW solution. Features and Specifications The Hamilton FLOW PCR Setup Instrument (PSU) is characterized by its precision and ability to integrate into automated workflows. Automation: It automates the pipetting and distribution of PCR components (samples, master mixes, primers) in 96- or 384-well PCR plates. Volume range: The hardware is designed for aspiration and delivery of volumes up to 1 ml. Traceability: It has automatic tracking of barcodes on accessories and con ...
Machine Type: Kieserling Six-Roll Pipe Straightening Machine Working range Ø 5 to Ø 45 mm Flow Direction: Right to Left Speed 37 / 50 / 75 meters/min Make Kieserling, type VRM 35 Year of construction Refurbished in 2023 Location: Solingen Weight approx. 2,000 kg with substructure and drives Country of origin: Germany Delivery terms ex works
Machine type: Kieserling VRM 20 Flow Direction: Right to Left Target speed with 3-speed manual transmission, m/min 37.5 / 50 / 75 Main operation 1.5KW Make Kieserling, type VRM 20 Location: Solingen NRW Length 2,200 mm Width 500 mm Height 1,700 mm Weight approx. 600Kg Country of origin: Germany Delivery condition Ex-works Solingen, free loaded truck
Soundproofed, silent duct fan, TD2000, D315mm, S&P, new Special price If you have a VAT number, we will be happy to issue you with an invoice without VAT. New! - never been used and is completely new, - comes from a spare parts warehouse of a certified production facility, - has very slight storage marks, no effect on function 83 x 40 x 40cm, ca. 30kg 6 months warranty We give you 6 months warranty for these goods from the date of invoice. In case of any defect, which is not the fault of the buyer, the goods can be returned. We will refund the buyer only the product price paid to us. Updating in case of digital components is excluded. Also excluded is liability for direct and indirect consequential damages. Our terms and conditions apply, see our website. Austrian law applies without exception and court location St. Pölten.
Machine Type: Kieserling Nine-Roll Straightening Machine Working range rods Ø 5 mm to Ø 30 mm Flow direction: from right to left Speed approx. 40 m/min Made by Kieserling & Albrecht, type WRUW 1 Length 2,060 mm Width 1,450 mm Height 1,500 mm Weight 3,700 kg Country of origin: Germany Delivery time by arrangement Other: The machine is currently being completely overhauled by our specialist company. The pictures show a machine we have just delivered. The one offered here will be in equivalent condition at the time of delivery!
Machine Type: Kieserling Six Roll Straightening Machine Working range from Ø 18 mm to Ø 100 mm Flow direction: from left to right Speed 37.5 / 50 / 75 m/min. Make Kieserling, type VRM 75 Location Solingen Length 1,970 mm Width 980 mm Height 1,900 mm Weight approx. 3,900 kg Country of origin: Germany Delivery time approx. 12 weeks Other: The machine is completely overhauled by our specialist company.
Machine Type: Kieserling Six-Roll Pipe Straightening Machine Working range Ø 3 to Ø 20 mm Flow Direction Right to Left Speed 37 / 50 / 75 meters/min Make Kieserling, type VRM 000 Weight approx. 800 kg Country of origin: Germany Delivery time approx. 8 weeks
Machine Type: Kieserling Six-Roll Straightening Machine Working range Ø 6 to Ø 60 mm Flow Direction Left to Right Speed 37 / 50 / 75 meters/min Make Kieserling, type VRM 60 Weight approx. 3,800 kg Country of origin: Germany Delivery time approx. 12 weeks
We offer directly on behalf of the owner : Bending press, second-hand Make : Graebener Maschinentechnik (Gräbener) Type : GRNM Year of construction : 2005 Flexural force max.: 16.000 kN ( 1.600 t ) Tool length : 1,600 mm Data at 520 N/mm2 Pipe diameter max.: 1,524 mm Tube diameter min.: 457 mm Sheet thickness max.: 40 mm Max. pipe length: 13.2 m Pipe length min.: 6m Pipe weight max.: 25 t Total power requirement approx.: 245 kW / 400 V / 50 Hz Approx. space: 27 x 3 m Total weight approx.: 90t / basic machine approx. 65t Further technical data and details on request or see data sheets in photos / PDF The machine was built in 2005, worked until 2021 and was professionally dismantled and packed for transport.
Machine Type: Kieserling Six Roll Pipe Straightening Machine Working range Ø 5 to Ø 45 mm Flow Direction Left to Right Speed 37 / 50 / 75 meters/min Make Kieserling, type VRM 35/45 Location Solingen Weight approx. 2,800 kg Country of origin: Germany Delivery time approx. 12 weeks Delivery condition ex works Other: Important: the machine is currently being overhauled by our company. The pictures show a machine we have just delivered. The one offered here will be in equivalent condition at the time of delivery!
Machine Type: Kieserling Nine-Roll Straightening Machine Working range tubes and rods Ø 5 mm to Ø 30 mm Flow direction from right to left Speed 40 m/min Make Kieserling, type WRUW 1 Location Solingen Length 1,600 mm Width 1,400 mm Height 1,600 mm Weight 3,700 kg Country of origin: Germany Delivery time approx. 4 weeks Other: The scope of supply of the machine includes the complete finishing for loading and removing the straightening material, consisting of: pre-bearing with roll-off slope, infeed channel with pusher, discharge channel with ejector, roll-off slope, collection belt trough.
maximum number of results exceeded
please refine your search
