126,679 used machines on RESALE, but how to find them? Machine Search
Hydraulic press, single-column high-speed press, C-column press, oil-hydraulic press - Pressing force of the ram: approx. 35 tons -Clamping table: 500 x 470 mm -Insertion height: 650 mm -Insertion width: 275 mm -Dimensions: 1300/900/H3200 mm -The machine can be dismantled to a height of: 2700 mm -Weight: approx. 1500 kg
Code: 0136 Brand: ITALPRESSE Model: FORMATIC 20.9 Hydraulic fluid membrane press Two sided lamination of veneer to panels shaped or profiled on one face and flat on the other to produce cabinet door raised panels, drawer fronts, desk tops, table tops, kitchen tops, etc. 3-D lamination of plastic foils (PVC, PPE, ABS, Transfer foil ) to panels sheped or profiled on one face to produce: cabinet doors, drawer fronts, desk tops, table tops, kitchen tops, store fixture components, room doors, etc. Platen dimensions mm 2000 x 900 Daylight mm 325 Cylinder stroke mm 325 Heating electric boiler Kw 27 Thrust ton 300 ton N° 3 thrust cylinders Hydraulic unit power Kw 5,5 Pressure control manometer Automatic pressure reset Opening timer Overall dimensions mm 3300 x 1400 x 2400 h Weight kg 8100
Nominal force: 2500 ton Ram stroke: 190 mm Number of strokes in 1 minute: 20 Shut height: 800 mm Bolster plate-to-ram adjustable stroke: 15 Table size: 1250x1400 mm Weight 124.230T
2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.
used canning press / packaging press Manufacturer: WAGNER Type: WDSP 7000 Year of construction: 1993 specifications: Pressing force: 70 t Specific pressing pressure: 318 kg/cm² Drive power: 15 kW / 400 V Duct format: 550 x 400 mm Filling opening L x W: 1,150 x 550 mm Compaction chamber: 700 x 550 x 400 mm Total stroke: 2,100 mm Machine length: approx. 5,500 mm Machine width: approx. 1,920 mm Capacity: approx. 1.5 t/h (depending on material) Package size, WxHxL: 550 x 400 x 280 - 550 mm Package weight: approx. 20 - 40 kg (depending on the setting of the package length) Machine weight: approx. 3,500 kg
Key data: 400 t, 800 mm
Oil-hydraulic double-column press 400 T with sliding table Press type: Double column press Thermally neutral 80 – 120 °C Number of operating pages 1 page Forces Pressing force max. 4000 kN Free tear-off force max. 400 kN Print build-up time Closed tool steel on steel Max. 4 sec. Dimensions: 3,800 mm long and 4,475 mm wide Max. opening width 800mm Stroke 800mm Table height above floor 1100mm Height above ground (height) approx. 4300 mm Hall height min. 5500 mm Parallel deviation at 20°C +/- 0.1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of the press without consumables and table top approx. 28 tons Press table Table size 1500x1500 mm Velocities Quick closing at 100 mm sec. Pressing speed 8 – 3 mm sec. Acoustic pressure Sound pressure level, measured at a height of 1.5m on the control pane ...
Pressure testing device, measuring device -with trailing-pointer -Max. pressure: 20 bar -High-pressure hose -Dimensions: 400/160/H200 mm -Weight: 4 kg
Proportional pressure control directional control valves, solenoid valves, pneumatic valves, air valves, pressure valves, valve blocks, control blocks -Operating pressure: 8 bar 120 psi -Dimensions: 200/85/H75 mm -Weight: 2 kg
Pressure sensor -Type: 3405BM2X2X2920 -Measuring range: 0-250 bar G -Max. Pressure: 1034 bar G -Input: 10-30 VDC -Output: 4-20 mA -Number: 2x available -Price: per piece -Weight: 0.5 kg
Pressure regulator intermediate plate -Type: LR-ZP-A/B-D2 35428 -From: 0 bar to: 12 bar -Price: per piece -Quantity: 8x Available -Weight: 2 kg
Hydraulic pressure switch -Type: TGL10952 -Adjustable: from 0 to 320 bar -Price: per piece -Number: 9 available -Weight: 0.5 kg
Proportional pressure control directional valve, solenoid valve, pneumatic valve, air valve, pressure valve, valve block, control block -Operating pressure: 8 bar 120 psi -Dimensions: 200/85/H75 mm -Weight: 2 kg
5/2 Pressure Booster -Type: DPA-40-10 537273 -VN: 43 -1: 2.5-8 bar 2: 4.5-10 bar -Weight: 1.5 kg
Proportional pressure control directional control valves, solenoid valves, pneumatic valves, air valves, pressure valves, valve blocks, control blocks -Operating pressure: 8 bar 120 psi -Dimensions: 200/85/H75 mm Price: per piece -Quantity: 2 available -Weight: 2 kg/piece
Hydraulic pressure switch, pneumatic pressure switch -Type: EDS 1100-050-1-009 -Pressure: 25 bar -Operating voltage: 24 VDC -Signal output: 0-5 VDC -Weight: 0.3 kg
Hydraulic pressure switch, pneumatic pressure switch -Type: EDS 1691-NC-016-000 -Pressure: 16 bar -Operating voltage: 24-20 VDC -Signal output: 4-20 mA Price: per piece Quantity: 2 available -Weight: 1 kg
Pressure valve, pressure gauge, pressure indicator, manometer -Measuring range: 0-6 bar -Fitting: Ø 63 mm -Thread: M12/1.5 mm -Price: per piece -Quantity: 10 available -Weight: 0.2 kg
Pressure switch -Type: C6045D 1043 -0.2-3 mbar -220/240 VAC 50 Hz 12(2) A -Pmax: 100 mbar -Protection class: IP 40 -Quantity: 3 pieces available -Price: per piece -Weight: 1.2 kg/piece
High-pressure radial fan, dust extraction fan, exhaust gas extraction, welding fume extraction, extraction, fan, pressure blower, vacuum blower -Engine power: 0.37 kW -Performance data: not available -Connection input: Ø 65 mm -Connection output: Ø 60 mm -Dimensions: 510/480/H470 mm -Weight: 49 kg
FRITZ MÜLLER ZE 625-4 hydraulic press was built in Germany by Fritz Müller GmbH & Co. KG. The machine has been continuously maintained and upgraded throughout its service life. The first major overhaul was carried out in 1988 by the manufacturer’s service Machinenfabrik Mueller-Weingarten AG. A second overhaul was carried out in 2020, during which the press was brought up to current safety requirements. As part of this overhaul, a new control system based on a SIEMENS SIMATIC S7 PLC controller and a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel was installed, the entire electrical system was replaced, seals were replaced and light curtains were installed. The FRITZ MULLER ZE 625-4 is an extremely versatile press designed for even the most demanding metal forming operations. It is capable of performing operations such as deep drawing, stamping, forging, straightening large w ...
ARISA S-2-630-240-120-LD mechanical press was built in 2005 in Spain by Arisa S.A. (now Nidec Press & Automation Co. (NP&A)). The machine on offer is an excellent choice for series production of components used in the broadly defined automotive or machinery industry. It enables even the most demanding metal forming operations, such as precise punching and stamping of metal parts. In addition to its standard purpose, depending on the tooling and material feed systems used, the machine can also be used as a transfer press or progressive press. All machining processes are performed with a high press force of 630 tonnes. The drive system, in the form of a flywheel and an eccentric gear, cooperating with two connecting rods, ensures even torque transmission and smooth control of the slider movement. The slider, on the other hand, is guided at eight points using roller guides, which increas ...
NIDEC ARISA S-2-500-240-120-FD mechanical press was built in 2006 in Spain by Nidec Press & Automation Co. (NP&A). It is an extremely versatile press that is used in the series production of components for the broadly defined automotive or machinery industry. It enables even the most demanding metal forming operations, i.e. precise punching and stamping of metal parts. In addition to its standard purpose, with the appropriate tooling and material feeding systems, the machine can also be used as a transfer press or progressive press. All processes are performed with a high press force of 500 tonnes. The drive system of the NIDEC ARISA S-2-500-240-120-FD press is based on a flywheel and an eccentric gear, cooperating with two connecting rods. This solution guarantees even torque transmission and a smooth working cycle. The slider, on the other hand, is guided in multiple points by rolle ...
Inv. Num. : 6992 Type: LKT 250 Producer: METALPRESS Created: 1963 Parameters: Ram stroke: 120 mm Plunger adjustment: 100 mm Machine weight: 2700 kg
Specifications Maximum pressure: 54 tons Power supply: 400V / 7.5 kW Press force: 5.62 kg/cm² Year of construction: 2005 Bale size: 1200x800x1200 mm Productivity: approx. 2 bales/hr Bale weight: approx. 500 kg Price: on request Machine is fully functional, after technical supervision. Price also includes paint renovation.
Description The Actuator Pressure Controller (APC) is a pressure control system developed for the calibration and testing of pneumatic control boxes. With this APC, it is possible to generate a pressure or vacuum level to be reached instantly or with a predefined control ramp. In addition, an external sensor can be used to measure the pressure obtained. It is possible to check the calibration of a pneumatic control box with a complete hysteresis cycle, defining all the parameters of the adjustment process. The pressure data from the sensors is recorded and analysed to check the maximum permissible hysteresis, either as an absolute value or as a proportion of the movement of the control box. Different control configurations can be saved and reloaded on demand. The calibration control cycles are carried out via 3 ports, 2 inlets from the test bench supplying the APC box with dry and clean ...
Specifications Maximum pressure: 12 tons Power supply: 380V/ 5.5 kW Press force: 2.5 kg/cm² Year of construction: 1985-1993 Bale size: 800x600x(600-1000)mm Productivity: approx. 3 bales/hr Bale weight: approx. 100 - 200 kg Price: on request Machine is fully functional, after technical supervision.
maximum number of results exceeded
please refine your search
100 € 
