128,994 used machines on RESALE, but how to find them? Machine Search
Three welding machines are available. (1) Castolin+Eutectic CASTOWIG 150 G, power supply: 5A/10V to 150A/16V, max. short-circuit current: 0.15kA, weight: 50kg. (2) MIG O MAT WIGSTAR 250i, welding current: 10-250A, duty cycle: 100% at 160A, 60% at 200A. (3) Lorch SEW 200N, voltage: 400V, welding current: 230A, cooling: gas-cooled. (4) Heberle stud welding systems cd System 2010, connected load: 0.6kVA. On-site inspection is possible.
max. wheel diameter: 2500 mm gear width: 1200 mm max. module: 32 min. module: 3 total power requirement: 25 kW weight of the machine ca.: 60 t dimensions of the machine ca.: m Gear , min. / max. 180 / 2,500 mm Module 3 - 32 Helix angle, max. 10 - 35 ° Gear width for straight gears 1,200 mm Stroke length, approx. 100 - 1,200 mm No. of strokes 80 - 350 /min Stroke position adjustable 300 mm Stroke speed 4 - 40 mm Max. weight of workpiece, approx. 18,000 kg Min. / max. no. of teeth 16 / 576 Table size x bore 1,400 x 500 mm Grinding wheel Ø, approx. 500 mm Grinding wheel peripheral speed 34 m/s Total electrical load, approx. 45 kW - 380 V - 50 Hz Weight of machine, approx. 60,000 kg Accessories / Special Features: Hydrostatic guides in grinding slide, table and in all other guideways. Completely covered working area with sliding doors. Automatic grinding process for various cycles, with ...
Injection pressure: 2100bar, injection volume: 595cm³, injection weight: 565g, injection speed: 299cm³/s. Clamping force: 250t, clamping force: 275t, platen dimensions X/Y: 920mm/920mm, opening stroke: 575mm, mold height min./max.: 200mm/685mm, tie bar distance: 585mm, ejector stroke: 175mm, ejector stroke: 180mm, centering: 160mm, operating hours: 62149h. Documentation available. On-site inspection is possible.
max. wheel diameter: 2500 mm gear width: 0 mm max. module: 34 min. module: 1 total power requirement: ca. 15 kW weight of the machine ca.: 15 t dimensions of the machine ca.: 4,20 x 2,00 x 2,90 m Extra große ZR-Prüfmaschine, Gegenhalter The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
End mill, end mill, cutter, face mill, milling head -Manufacturer: PWZ, Attachment milling cutter, Angle end mill, Cylindrical end mill, Original packaging -Type: 100x50x40 251G-TH10 66-007 -Hole: Ø 40 mm -Number: 9x milling cutters available -Price: per piece -Box dimensions: 125/115/H70 mm -Weight: 1.6 kg/pc.
Decoiler Coil weight: 2,5 ton Material width: 50 - 500 mm Coil exterior diameter: 1400 mm Expansion range: 420 - 520 mm Leveller / Straightener Material width : 500 mm Number of levelling rolls: 9 pcs. Diameter of the levelling rolls: 50 mm Number of pinch rolls: 2 pcs. Material thickness: 6 mm Cross section: 3000 sq mm Feeding speed: 6 - 24 m / min
workpiece diameter: 250 mm centre distance: 0 mm honing length max.: mm max. module: 5 Gear Ø, min./max. 10 / 250 mm Module range 1 - 5 Length of teeth / max. table stroke 500 mm Height of centres of tailstocks 220 mm Max. weight of workpiece 50 / 100 kg Honing head swivelling +/- 35 ° Speeds of honing tool 20 - 500 rpm Size of honing tool, Ø x width 300 x 40 mm Workpiece speeds 500 - 3,000 rpm Total adjustment of cross slide 270 mm Rapid traverse of cross slide 50 mm Infeed travel of cross slide, mechanical 1 - 8 mm/Ø Roughing / finishing infeed 1 - 29 / 0.2 - 2.8 mm/sec Table speeds, hydraulic 0 - 6 m/min Total electrical load 5.5 kW - 380 V - 50 Hz Weight 3,200 kg Accessories / Special Features Working parameters can be preset using counters and control units. Automatic working process with workpiece counter. All roughing and finishing infeeds can be adjusted by a decade switch ...
This 5-axis ICON 6-250 was manufactured in 2011, featuring a robust design with a total weight of 52,200 kg and a power capacity of 120 kVA. It includes 6 stations with both horizontal and vertical processing capabilities, a tool magazine with a 12-place capacity, and a CNC plate table with precise positioning. Ideal for complex machining tasks, the machine offers a maximum spindle speed of 12,000 rpm and a torque of 29 Nm. Contact us for more information about this machine.
A Trima CNC gantry machining center is available. Workpiece dimensions X/Y/Z: 2500mm/1100mm/80mm, spindle power: 7.5kW, speed: 24000rpm, tool positions: 10, traversing speed X/Y/Z: 55m/35m/15m/min. Machine dimensions X/Y: approx. 4400mm/2500mm, weight: approx. 3200kg, control: Siemens Sinumerik. The machine has a control defect. The reference run is aborted. Documentation available. On-site inspection is possible.
TBA 19 machines have been developed for the filling of compact formats. The 250 milliliter Slim format is one of the most requested volumes. In this format, the system is used for many types of products. Before and during the repair work, we constantly check the condition of all existing parts and, if necessary, replace them before reassembling the machine. After extensive work in our workshop, we test all machine components intensively. Our aim here is the smooth interaction of all machine groups up to the finished product. These tests at the end of the technical work are particularly important for the later use of the machine. We can find existing errors in the system and fix them before the next production use. TBA 19 machines are available in different development stages. We will be happy to explain the extensive steps to make the system operational again for you. On request, we ca ...
TBA 19 machines have been developed for the filling of compact formats. The 250 milliliter base format is one of the most requested volumes. In this format, the system is used for many types of products. Before and during the repair work, we constantly check the condition of all existing parts and, if necessary, replace them before reassembling the machine. After extensive work in our workshop, we test all machine components intensively. Our aim here is the smooth interaction of all machine groups up to the finished product. These tests at the end of the technical work are particularly important for the later use of the machine. We can find existing errors in the system and fix them before the next production use. TBA 19 machines are available in different development stages. We will be happy to explain the extensive steps to make the system operational again for you. On request, we can ...
: M01.43870 frequency: 50 Hz voltage: 400 V : 24 V connected load: 48 kW rated current: 63 A control: Siemens 840 D turning diameter: 250 mm turning length: 100 mm weight of the machine ca.: 7,5 t turning length external: / innen 100 mm workpiece length - min.: 29 mm workpiece length - max.: 100 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
honing diameter: 80 mm stroke: 280 mm throat: 300 mm total power requirement: 6 kW weight of the machine ca.: 2,6 t Honing Ø 10 - 100 mm Max. honing depth, approx. 250 mm Max. spindle stroke 260 mm Distance between spindle and column 300 mm Mounting height 1,000 mm Table size 350 x 500 mm Height of table above floor 500 mm Spindle speeds in 2 steps, infinitely variable, approx. 85 - 300 rpm 170 - 600 rpm Stroke speed, infinitely variable, hydraulic 0 - 23 m/min Spindle drive 2 kW Total electrical load 6 kW - 380 V - 50 Hz Weight 2,600 kg Accessories / Special Features Built-on 2-station tilting table which accommodates 2 workpieces. Mechanical workpiece clamping, using a manual lever. Hydraulic infeed of the tool. Switch-off via timer. Air measuring device (probably). Honing oil unit. Various splash shields, etc. Condition : Good. Machine can be in ...
turning diameter: 250 mm turning length: 100 mm control: SIEMENS 840 D total power requirement: 35 kW weight of the machine ca.: 7500 kg dimensions of the machine ca.: m E M A G (Germany) Vertical CNC Controlled Hard Turning and Grinding machine with tool turret and workpiece handling System Model VSC 250 DS Year 2004 # M7 28.69324 _______________________________________________________ Turning Ø, max. 250 mm Turning length internal / external 100 mm Workpiece length min./max. 29 – 100 mm 6-positon tool turret Ø / swing-Ø 480/790 mm Workpiece spindle Slide travel, X / Z / stroke 680 / 400 / 200 mm Feed rate / Quick feed X/Z 45/30 m/min. Feed force X/Z 5,5/11 kN Spindle speed 4.300 / 6.000 rpm Spindle drive 28 kW Total electrical load, ...
faceplate diameter: 2500 mm swing diameter: 2865 mm turning height: 3000 mm Control: R & D type: MTC 4 Rest: 2 slide adjustment: 1500 mm turning speeds: 140 U/min tool change unit: 12 Pos. total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Machine is modernized The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was cre ...
This 3-axis MORI SEIKI SL-253B MC/1000 was manufactured in 2000. It features a maximum turning diameter of 260 mm and a turning length of 1,035 mm. The machine is equipped with a spindle speed range of 35â3,500 RPM and a robust turret with 12 stations. If you are looking to get high-quality turning capabilities, consider the MORI SEIKI SL-253B MC/1000 horizontal turning machine we have for sale. Contact us for further details.
This 4-axis HELLER MCH 250 was manufactured in 2005. It features an XYZ travel of 800 x 800 x 800 mm and a pallet size of 630 x 630 mm. The machine is equipped with a 100-tool automatic tool changer and a 6-pallet pool for enhanced productivity. If you are looking to get high-quality machining capabilities, consider the HELLER MCH 250 horizontal machining centre we have for sale. Contact us for further details.
core drilling diameter max.: 25 mm bore depth: 1000 mm swing diameter: mm total power requirement: 25 kW weight of the machine ca.: 12,5 t dimensions of the machine ca.: m T B T (Germany) CNC-Controlled Horizontal Deep Hole Drilling Centre Model BWP 250 Year 1996, but reconditioned mechanically and electrically in 2006 ______________________________________________________________________ _____________ Working range: X Axis, machine column cross 2,000 mm Z Axis, drilling slide horizontal 1,200 mm Drilling depth 1.000 mm Y Axis, drilling slide vertical 1,100 mm Table clamping area 1,200 x 2,000 mm Drilling capacity in solid material, approx. 4 - 25 mm Tool holder taper HSK 50 Spindle speeds 1.260 - 15,000 rpm Feed rates / quickfeed, XYZ, infinitely variable 100 - 10,000/15.000 mm/min. Force rate of feed ...
cutting diameter: 255 mm saw band length: 2765x 0,9 x 27 mm cutting width: 300 x 180 mm turning speeds: 35 + 70 U/min total power requirement: 1,8 kW weight of the machine ca.: 450 t dimensions of the machine ca.: 1,7 x 1,23 x 1,75 m SPECIAL PRICE! Double miter metal band saw, frequency converter hydraulic semi-automatic GBS 250 Super HA-I Easy • miter left 60° + right 45° • Material height sensor (automatic cut start detection) • Frame and gear made from one piece, very quiet cut and very low vibration • Hydraulic vice can be moved sideways a. • Guided, high quality industrial bearings • Solid vice + machine casting • Large machine bed • Machine base with tool compartment and chip drawer • Cut monitoring by ammeter • Cutting pressure feed regulator • Support roller (infeed side) • Ball bearing turntable Semi-automatic function: 1. Clamp material 2. Saw starts 3 ...
This 4-axis HELLER MCP 250 was manufactured in 2000. It features a maximum spindle speed of 6000 rpm and an automatic tool changer with 52 positions. The machine is equipped with twin pallets and offers an XYZ travel of 800 x 800 x 710 mm. If you are looking to get high-quality machining capabilities, consider the HELLER MCP 250 horizontal machining centre we have for sale. Contact us for further details.
This 5-axis SPINNER U5-2520 was manufactured in 2016. It features an impressive X-axis travel of 2660 mm, Y-axis travel of 520 mm, and Z-axis travel of 460 mm. The machine is equipped with a spindle speed of 10,000 rpm and an automatic tool changer with 2x52 positions. If you are looking to get high-quality machining capabilities, consider the SPINNER U5-2520 vertical machining centre we have for sale. Contact us for further details.
Saw blade diameter: 255 mm Sawblade tiltable: 45 ° Cutting height: 75 mm Table dimensions: 640 x 920 (ausgezogen) mm Saw blade: 30 mm Motor output: 1,6 kW connected load frequency: 230 V machine weight ab.: 32 kg Dimensions (L/W/H): 720 x 1080 x 920 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 2,5 kN stroke: 45 mm throat: 90 mm Working height from to: 80 - 220 mm table surface area: 120 x 60 mm weight of the machine ca.: 22 Kg dimensions: 160 x 230 x 390 mm Hand presses with rack HZ 250 The power is transmitted via a rack and pinion construction. she finds their use where during the working process a constant pressure is needed. Precisely manufactured, spindle hardened and ground, unlimited service life Long spindle guide, optimal pressure performance, T-slot according to DIN 650 milled in the middle, sliding blocks fit exactly. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding wheel diameter: 250 mm no. of working stations: 2 Stück connected load frequency: 230 V turning speeds: 2850 U/min total power requirement: 1,5 kW weight of the machine ca.: 25 Kg dimensions: 0,65 x 0,32 x 0,35 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
capacity 90 degrees: round: 255 mm capacity 90 degrees: square: 240 mm : 300 x 180 saw band length: 2.765 x 27 x 0,9 mm mm table height: 870 mm band speed: 18 - 110 m/min Control: CNC total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,63 t dimensions of the machine ca.: 1,8 x 1,85 x 1,85 m Miter band saw, fully automatic GBS 255 Super VA-I CNC • miter left 45° automatic operation • miter left 60° semi-automatic operation (cuts without programming) • Material height sensor (automatic cut start detection) • Frame and gearbox made from one piece, very quiet cut and very low vibration • Removable chip tray (disinfection) • Shockproof and ergonomic control panel with oil-resistant EPDM cover • High performance positioning with incremental encoder (CNC) c. • Top access to the saw, material and feed unit • Hinged safety cover • Fine feed adjustment • Semi-a ...
grinding wheel diameter: 250 mm connected load frequency: 230 V : 90 - 180 U/min weight of the machine ca.: 18 Kg dimensions: 470 x 300 x 440 m Knife sharpening device with variable speed Grinding wheel 250 x 50 x 12mm, grit 220 Leather disc 200 x 30 x 12mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter over bed: 250 mm turning diameter over slide rest: 140 mm turning length: 550 mm turning speeds: 125 - 2000 U/min centre height: 125 mm spindle bore: 26 mm tailstock quill taper MT: 2 MK tailstock quill stroke: 65 mm connected load frequency: 230 V total power requirement: 0,75 kW weight of the machine ca.: 0,135 t dimensions of the machine ca.: 1,25 x 0,6 x 0,6 m Speed in 6 levels 125 - 2000rpm. 3-jaw chuck 125 mm. 4-jaw chuck 125 mm. (Independent) Fixed bezel. Revolving bezel. 4-fold steel holder. chip tray. back panel. spindle protection. Hardened bed rails. Longitudinal feed with left / right switching. Set of change gears. Associated Tools. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
This EMAG VSC 250 vertical turning machine was manufactured in 2011. It features a Siemens SINUMERIK 840Dsl control system, a robust hydraulic 6-jaw chuck, and a flange turret with 12 tool positions. With a spindle speed up to 4500 rpm and a main spindle drive power of 28kW at 40% duty cycle, its ideal for precise, efficient operations. For more information about this vertical turning machine, please reach out to us.
plate thickness: 3 mm blade length: 250 mm angle adjustable from - to: fest 90 Grad table surface area: 900 x 790 mm total power requirement: kW weight of the machine ca.: 0,65 t dimensions: 1,2 x 0,9 x 1,1 m Hydraulic notching machine - Footswitch - 2 pcs. sheet metal stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cutting diameter: 250 mm saw band length: 3150 x 27 x 0,9 mm table height: 700 mm cutting width: 250 x 320 mm cutting speed: 25 - 90 m/min dimensions of saw-band: 2480 x 27 x 0,9 mm : 120 mm : 120 mm : 190 mm Impact energy: 190 mm connected load frequency: 400 Volt total power requirement: 1,5 kW weight of the machine ca.: 0,5 t dimensions: 0,95 x 1,16 x 1,98 m Rock-solid band saw for solid material - Double miter cuts up to 60° - AutoCut - Vice with quick clamping device - Belt tension control - Electric automatic cooling system - Material suggestion The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
This 4-axis HELLER MCH 250 was manufactured in 2007. It features a spindle speed of 6000 rpm and a BT50 tool holder. The machine is equipped with an automatic tool changer that holds 100 tools, enhancing productivity. If you are looking to get high-quality machining capabilities, consider the HELLER MCH 250 horizontal machining centre we have for sale. Contact us for further details.
capacity 90 degrees: round: 255 mm capacity 90 degrees: square: 240 mm : 300 x 180 saw band length: 2.765 x 27 x 0,9 mm mm table height: 870 mm band speed: 18 - 110 m/min total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,63 t dimensions of the machine ca.: 1,8 x 1,85 x 1,85 m Miter band saw, fully automatic GBS 250 Super VA-I MPS • Miter left. 45° automatic operation • Miter left. 60° semi-automatic operation (cuts without programming) • Shockproof and ergonomic control panel with oil-proof EPDM cover a. • Material height sensor c. (Automatic cut start detection) • Frame and gearbox made from one piece, very quiet cutting and very low vibration • Chip tray can be removed (disinfection) • Easy access to the saw, material and feed unit • Foldable safety cover • Fine feed adjustment • Semi-automatic. Cut! Saw automatically with microprocessor control Adj ...
turning diameter over bed: 250 mm turning diameter over slide rest: 140 mm turning length: 550 mm turning speeds: 50 - 2000 U/min centre height: 125 mm spindle bore: 26 mm tailstock quill taper MT: 2 MK tailstock quill stroke: 65 mm connected load frequency: 230 V total power requirement: 1,1 kW weight of the machine ca.: 0,15 t dimensions of the machine ca.: 1,3 x 0,6 x 0,65 m Benchtop lathe 3-axis LCD digital display system fully assembled. Longitudinal feed. 3-jaw chuck 125 mm. 4-jaw chuck 125 mm. Clamping plate. 4-way steel holder. Clock for thread cutting. Drip tray Hardened bed tracks. Emergency stop switch. Forage protection Set of wheels. Appropriate tools. Base cabinet is optional The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 250 mm capacity 90 degrees: round: 80 mm capacity 90 degrees: square: 70 mm capacity 90 degrees: flat: 95x60 mm capacity 45 degrees: round: 70 mm capacity 45 degrees: square: 60 mm capacity 60 degrees: flat: 65x60 mm total power requirement: 1,0 kW weight of the machine ca.: 0,075 t dimensions of the machine ca.: 0,3 x0,8 x0,75 m SPECIAL PRICE! The ideal metal circular saw for workshop and assembly • For miter cuts left up to 45° • For sawing steel, stainless steel and, to a limited extent, aluminum profiles • Spindle vice with double clamping arm for low-burr cuts • Optionally with 230 V or 400 V motor • Automatic cooling directly on the saw blade • Double bearing for saw head • 24 V safety switch in the handle with restart lock • Length stop, assembly tool • Subframe (option) additional price 172,-EUR ATTENTION: Price is without saw blade! (saw bl ...
plate thickness: 8 mm blade length: 250 mm angle adjustable from - to: fest table surface area: 840 x 750 mm total power requirement: 3,0 kW weight of the machine ca.: 1,3 t dimensions: 1,4 x 1,1 x 1,5 m Hydraulic notching machine - Footswitch - 2 pcs. sheet metal stop The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter over bed: 250 mm turning diameter over slide rest: 130 mm turning length: 550 mm turning speeds: 50 - 2000 U/min centre height: 125 mm spindle bore: 20 mm tailstock quill taper MT: 2 tailstock quill stroke: 60 mm metric threading: 0,4 - 3,0 mm thread - inch: 10 - 44 TPI thread - module: 0,2 - 12,5 mm connected load frequency: 230 V total power requirement: 1,0 kW weight of the machine ca.: 0,12 t dimensions of the machine ca.: 1,09 x 0,59 x 0,45 m Equipped with - 20 mm spindle passage - adjustable guideways - Powerful 1.0 kW motor - continuously variable speed Scope of delivery: - 3-jaw chuck 100 mm, - 4-jaw faceplate chuck 125mm - standing and rotating bezel - Splash guard - Feed protection The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Description: Suitable for dressing and profiling diamond and CBN grinding wheels. ccesories: Total enclosure., Motor Upgrade (stronger motors for the wheel being dressed and the dressing wheel),, Wheel motor strengthened to 4 kW,, Dressing wheel motor strengthened to 2,2 kW,, 2 Machine lights 12 V,, Optical linear scale with digital display counter (0,001 mm) X, Z Axes,, 2/3” TV Camera with 15” LCD monitor (microscope with zoom 15‐120X included),, High performance swivelling angle reader (0,05°),, Diamond / CBN wheel spindle speed stepless adjustable 100 - 1000 rpm,, Turning speed of dressing wheel stepless adjustable 200 - 2000 rpm,, Stepless oscillation speed,, Automatic central lubrication,, SIC Wheel dresser manual,, Grinding wheel holder:: HSK 50 E, Diamond grinding wheel diameter: 50 - 250 mm, max. width of grinding wheel: 70 mm, Grinding wheel bore diameter: 20 mm, Speed of ...
Machine designed for profiling and dressing flats, side, angular, radius and special shapes on diamond and CBN wheels. Especially suitable for single or multiple wheel packs., Accessories:, Motor Upgrade (stronger motors for the wheel being dressed and the dressing wheel),, Wheel motor strengthened to 4 kW,, Dressing wheel motor strengthened to 2,2 kW,, 2 Machine lights 12 V,, Optical linear scale with digital display counter (0,001 mm) X, Z Axes,, 2/3” TV Camera with 19” LCD monitor (microscope with zoom 15‐70X included),, High performance swivelling angle reader (0,05°),, Diamond / CBN wheel spindle speed stepless adjustable 100 - 1000 rpm,, Turning speed of dressing wheel stepless adjustable 200 - 2000 rpm,, Stepless oscillation speed,, Automatic central lubrication,, SIC Wheel dresser manual,, Protection cover., Specifications: Wheel spindle taper: HSK50E (alternatives possibl ...
Two Bosch vertical form fill and seal machines are available. 1) Bosch SVB 2501 A, year of manufacture: 1993, bag type: pillow bag, bag weight: 250g/500g, bag length range: 80mm-250mm, max. production output: 40 cycles/min, power consumption: 3kW, machine dimensions X/Y/Z: approx. 1300mm/2500mm/1700mm, weight: approx. 1100kg. Including clipping unit PS mako BS 600-CSP, year of manufacture: 2015. 2) Bosch SVB 3601 L, year of manufacture: 1996, bag type: pillow bag, bag weight: 250g/500g, max. bag length: 400mm, bag width range: 80mm-360mm, max. production speed: 40 cycles/min. Including clipping unit PS mako BS 600-CSP, year of construction: 2015, documentation available. On-site inspection is possible. Expected to be available from mid-January 2025.
Flywheel size: SAE1/14, Mecc Alte ECO38-1L/4C, DER1 voltage regulator, 300kVA continuous / 330kVA stand-by power; Gross weight [kg]: 771
For sale is a ProJet 2500Plus from 2017. The device is in perfect condition, test printing is possible (for an expense allowance, which will be offset against purchase)., Accessories: EasyClean System from 3D Systems, second build platform, Technology: MultiJet Printing
A new belt roasting machine for nuts in the food industry is available. Fuel: diesel/electricity/gas/LPG, output: 2kW, machine dimensions X/Y/Z: approx. 3600mm/1900mm/1950mm, operating hours: 31h. Roasting capacity per hour: hazelnut kernels: 160kg, shelled peanuts: 150kg, shelled peanuts: 35kg, shelled pistachios: 90kg, sunflower seeds: 70kg, pumpkin seeds: 70kg, almonds: 120kg, cashew nuts: 150kg, chickpeas: 120kg. Including salt kettle with a capacity of 35kg and fully automatic high-pressure belt washer. Documentation available. On-site inspection is possible.
bore capacity in steel (diameter): 55 mm arm length: 2500 mm workpiece height max.: - mm total power requirement: 8 kW weight of the machine ca.: 5 t dimensions of the machine ca.: 4 x 1 x 3 m Radial drilling machine MK 5 Spindle holder MK 5 Speed range 30 - 1500 min-1 Feed rates 0.05 - 0.6 mm/rev Space requirement approx. 3.7 x 1 x 3 m Weight approx. 5 tonnes (estimated) Working range: MK 5 x 2500 Drive: 3.7 / 6 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
swing diameter:200 mm weight of the machine ca.:15 t Distance between tips:832,5 mm turning length:380 mm with chip conveyor and belt filter press, infeed and outfeed belt 2 x 12-position revolvers
turning diameter:200 mm swing diameter:260 mm turning height:60 mm
On behalf of a customer, we are selling a 3D Systems MultiJetPrinter type ProJet 2500Plus in very good condition. The machine was used as a dealer demo machine., The machine has been equipped with new drive belts and new filters. All materials have been removed according to the manufacturers instructions. The machine is empty. The printing time is approx. 1400 hours, 181,000 layers were printed with approx. 24KG of building material and approx. 33KG of support material., Equipment:, - 3D Sprint Basic Complimentary Software (on-line activation), Installation: 2016, Print modes: HD - High Definition, Net build volume (xyz) net build volume (xyz) hd mode: 294x211x144mm / 11.6x8.3x5.6in, Resolution (xyz) resolution (xyz) hd mode: 800x900x790 DPI; 32μ (0.0012 in) layers, Accuracy (typical): ±0.025-0.05 mm per 25.4 mm of part dimension. Accuracy may vary depending on printing parameters, ...
carrying capacity: 250 kg number of suction cups: 6 suction cup dia.: 215 mm Vacuum lifter VH 6-250 for the horizontal transport of smooth, dry and airtight panels. Robust supporting structure made of steel, painted in RAL 2000 with low Own weight. consisting of: - 1x galvanized longitudinal beam with a length of 2,400 mm - 3x galvanized crossbeams with a length of 1,000 mm - 6x Springy, articulating and adjustable suction cup holders - 6x suction cups Ø 215 mm, the seal can be separated in case of wear whose metal supports can be changed inexpensively and without tools - 6x ball valves to switch off individual suction cups, thus also smaller formats can be lifted without having to move suction cups or traverses. - 1x spiral connection cable small helix: with an extension length of 3,500 mm, designed as an extension cable with CEE plug and coupling. is routed to the lifting device nex ...
maximum number of results exceeded
please refine your search
