130,400 used machines on RESALE, but how to find them? Machine Search
cutting diameter: 300 mm saw band length: 3320 x 27 x 0,9 mm mm cutting width: 300 mm Control: NC capacity 90 degrees: flat: 330x 260 mm capacity 90 degrees: square: 260 x 260 mm capacity 45 degrees: square: 250 mm capacity 45 degrees: flat: 270 x 200 mm capacity 60 degrees: round: 180 mm capacity 60 degrees: square: 170 mm band speed: 15 - 100 m/min total power requirement: 2,2 kW weight of the machine ca.: 1,1 t dimensions of the machine ca.: 3,3 x 2,83 x 2,23 m Furnishing: - fully automatic electro-hydraulic band saw with additional semi-automatic, semi-automatic-dynamic and manual operation - Automatic cycle (cuts from 0° to 60° left) - Semi-automatic, semi-automatic-dynamic and manual cycle (cuts from 45° right to 60° left) - Manual or semi-automatic dynamic cycle to make cuts outside of series production can be carried out directly without programming. - Numerically contro ...
cutting diameter: 280 mm saw band length: 3320 x 27 x 0,9 mm mm cutting width: 330 mm Control: NC capacity 90 degrees: flat: 330x 260 mm capacity 90 degrees: square: 260 x 260 mm band speed: 15 - 100 m/min total power requirement: 2,2 kW weight of the machine ca.: 1,24 t dimensions of the machine ca.: 3,3 x 2,83 x 2,23 m Attention: special price! •Fully automatic hydraulic band saw •Miter cuts up to 60° left possible •Saw band length: 3650x27x0.9 •Single stroke: 600 mm (programmable up to 10m) •Simple touchscreen operation. •Saw arm made of nodular cast iron - robust and stable •Required space 3.4 m² •Footprint 1900mm wide x 1800mm deep The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
turning diameter over bed: 320 mm turning diameter over slide rest: 200 mm turning length: 900 mm turning diameter in the gap: 320 mm turning speeds: 75 - 2000 U/min centre height: 160 mm spindle bore: 38 mm tailstock quill taper MT: 3 connected load frequency: 400 V total power requirement: 1,5 kW weight of the machine ca.: 0,4 t dimensions of the machine ca.: 1,6 x 0,75 x 1,7 m SINO digital display 3-jaw chuck 200 mm. 4-jaw chuck 200 mm. Faceplate 250mm bezel fixed Quick-change steel holder with 4 pcs. steel holder machine light Chip tray, chip protection wall Hardened and ground bed tracks lining protection machine tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 350 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 110 mm capacity 90 degrees: flat: 200x88 mm capacity 45 degrees: round: 115 mm capacity 45 degrees: square: 110 mm capacity 45 degrees: square: 150x80 mm total power requirement: 1,5/1,8 kW weight of the machine ca.: 0,22 t dimensions: 0,7 x 0,9 x 1,9 m ATTENTION: SPECIAL PRICE! - Miter left/right 45° - head diagonal cuts up to 45° (shifter) - Pneumatic double quick clamping device Vices close when lowering - Ball bearing table - Machine base - Powerful and powerful - High-quality workmanship The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
saw blade diameter: 370 mm capacity 90 degrees: round: 120 mm capacity 90 degrees: square: 100 mm : 180x100 mm Working height: 925 mm saw blade turning speeds: 17 - 70 U/min total power requirement: 3,0 kW weight of the machine ca.: t dimensions of the machine ca.: 1,9 x 1,45 x 2,1 m SPECIAL PRICE! High-performance vertical circular saw Hydropneumatic fully automatic. (20195) · miter left 60° + right 45° · Hydro-pneumatic control of the saw unit · Electro-pneumatic material feed unit · Smooth-running, powerful worm drive with large Transmission ratio, integrated in a stable cast housing for Achieving optimal cutting results · Vice with double clamping arm for low-burr cuts Lateral quick shift when changing the miter · Precision prism guide of the gear head, laterally adjustable · Particularly stable base frame with built-in automatic cooling system · Large chip drawer ...
turning diameter over bed: 250 mm turning diameter over slide rest: 140 mm turning length: 550 mm turning speeds: 50 - 2000 U/min centre height: 125 mm spindle bore: 26 mm tailstock quill taper MT: 2 MK tailstock quill stroke: 65 mm connected load frequency: 230 V total power requirement: 1,1 kW weight of the machine ca.: 0,15 t dimensions of the machine ca.: 1,3 x 0,6 x 0,65 m Benchtop lathe 3-axis LCD digital display system fully assembled. Longitudinal feed. 3-jaw chuck 125 mm. 4-jaw chuck 125 mm. Clamping plate. 4-way steel holder. Clock for thread cutting. Drip tray Hardened bed tracks. Emergency stop switch. Forage protection Set of wheels. Appropriate tools. Base cabinet is optional The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
was in action behind a 2019 FOSS Inline Fat Analysis System Meat Master(TM) II,, for raw meat,, designed to be mobile,, effective width: 400 mm,, feeding distance: 820 mm,, gradient: approx. 60° - length: approx. 3,800 mm,, Delivery height: approx. 2,500 mm,, Delivery distance: approx. 930 mm,, Lug width: 400mm, Stud height: 50mm, Cleat pitch: approx. 200mm, Hygienic version with central scaffold tube. The construction is very open. The belt is removed using round material. Drive and deflection stations are designed with sheet metal parts. In the lower run the, Belt worn by rollers. The conveyor is equipped with a quick clamping system. Thus, the belt can be lifted for cleaning or removed from the side. The belt is positively driven and, also forced, Support:, with rectangular tube support frame with castors, Product Tours:, Plastic profiles swiveling on both sides, Clear width = stud w ...
Loading trolley for all Vollmer ND loading centers available in as-is condition, unpainted or completely new and freshly painted.
Suitable for automatic tooth flank grinding on both sides of carbide-tipped circular saw blades. Accesories: full fairing coolant system Automatic central lubrication. Measuring system for measuring saw blades. Control panel with LCD color display. DNC service. Alphanumeric keyboard. Grinding speed and grinding path depending on the tooth surface, can be adjusted as required. 2 grinding wheel mounts Coolant level monitoring Automatic grinding wheel compensation Prepared for robot operation with automatic loading door oil pan 2 x saw blade magnet holder >Ø 320mm, >Ø 180 mm 1 centering ring., Circular saw blade diameter: 200 - 840mm, Circular Saw Bore Diameter: from 16 mm, Tooth pitch: 6 - 180mm, grinding path: up to 25 mm, tangential relief angle: 0 to 10 degrees, max. grinding wheel diameter: 125 mm, Grinding wheel bore diameter: 32 mm, Grinding spindle variable: 1600 - 5500 rpm,, Conn ...
HSK63-B,F Test Mandrel Suitable for Vollmer machine types: QWD 750 / QWD 760 / QWD 750 H / QWD 760 H / VPulse 500 and all models from the QXD series (200/250/400)
Adaptor for A-axis HSK63-B,F For manual and automatic loading. Suitable for Vollmer machine types: QWD 750 / QWD 760 / QWD 750 H / QWD 760 H / VPulse 500 and all models from the QXD series (200/250/400)
Wire guide elements for metal, spacing 100-200 mm, 15 mm longer Using these wire guide elements reduces the diameter of the workpieces that can be machined. Suitable for Vollmer machine types: QWD 76 P / QWD 750 / QWD 760 / QWD 750 H / QWD 760 H / VPulse 500
Description: external data input station for use with Vollmer ND brand saw blade handling systems. Serves for individual input of the various processing steps of a saw blade. The data input station with integrated router takes over the interface between the machines, to the customers own server or PC
Description: external data input station for use with Vollmer ND brand saw blade handling systems. Serves for individual input of the various processing steps of a saw blade. The data input station with integrated router takes over the interface between the machines, to the customers own server or PC
Suitable for cleaning cooling oil for grinding hard metal., container content: approx. 500 l, Filter performance: approx. 180 l/min, Filter fineness: >0.003mm, Connected load: approx. 4 kW (400 V/ 50Hz), Dimensions: W x D x H approx. 1600 x 1000 x 1000 mm, weight: approx. 1000 kg, mass: about 1000 kg, colour: light gray
A complete packaging and palletizing line for buckets is available. 1) Vollenda 2VNES2-6-E bucket filling machine, year of manufacture: 2009, bucket formats: 2kg-5kg, filling capacity 2kg/5kg: 1200/800 buckets/h. 2) Palletizer Ehcolo EPL 160, year of manufacture: 2009, empty pallet magazine positions: 15, max. pallet dimensions X/Y/Z: 800mm/1200mm/1500mm, palletizing capacity 2kg/5kg pails: 800/1200 pails/h. 3) Wrapping machine Robopac Rotoplat 3000HD, year of construction: 2009, max. rotation speed: 12 rpm, max. wrapping height: 2400mm, power: 11kW, weight: approx. 1400kg. Documentation available. On-site inspection is possible.
CDM VIBRO CLASSIFIER FOR GRANULATES, Constructed in 2003, 8 mm holes on 1st screen, Users manuals, drawings, CE., Available RECONDITIONED, (pictures show the machine prepared for optimizing transport), See how we recondition [HERE](.germanplast.eu/pages/what-we-do), AVAILABILITY: RUNNING
VERTICAL MIXER 20 m3 capacity, total height approx 7.000 mm including transmission group (can be customized), max Ø 2.400 mm.(standard transport), constructed in painted electro-welded carbon steel., inner auger diam.350 mm., lower loading hopper with safety grid and sampling shutter, complete with anti-dust cover, mm.600x500, pulley and belt transmission, protected by carters, inspection doors with safety limits, cleaning hinged door with on bottom of cone for complete discharging, with safety opening, side discharging pipe to big bag with valve mm.at 2.500 mm from ground, max electric level indicator, paddle type, automatic lubricating kit, electric motor 15 kw, complete with control panel., electric voltage: 400 V, 50 Hz, auxiliaries a.c. 24 V, CE compliance, drawings and instructions manual in English., Possible additions: wheeled slide, feeding screw and hopper, extraction auger, b ...
A ViscoTec volumetric filling machine for filling and dosing low to high viscosity products is available. Filling quantity range: 50ml-20000ml, filling capacity: 25l/min, product contact materials: stainless steel 1.4571, machine dimensions X/Y/Z: approx. 1550mm/550mm/750mm, weight: approx. 200kg. Documentation available. On-site inspection is possible.
Strapping capacity: 28/h, strap width: 12mm, strap tension: 100N-3500N, frame dimensions X/Y: 800mm/800mm, working height: 810mm, machine dimensions X/Y/Z: 1430mm/620mm/1540mm. On-site inspection is possible.
Two identical Videojet printers are available. One has only been tested for a few cycles, the other is still in its original packaging. Print heads: 1, max. number of print lines: 5, max. print speed: 278m/min, text storage capacity: 250, max. marking lines: 5, documentation available. On-site inspection is possible.
A VSB Verbufa for the positioning of minced meat, hamburgers, cookies, balls and sticks with high cycle output in packaging and packaging machines is available. Output: 110 portions/min, machine dimensions X/Y/Z: approx. 1700mm/950mm/1650mm, weight: approx. 500kg. Documentation available. On-site inspection is possible.
A mobile diesel three-phase generator set with a Volvo engine and Stamford generator mounted on a Steyr truck is available. 1) Steyr 17S230 truck, payload: 17t, engine power: 230kW, platform length: approx. 9m, engine-gearbox and rear axle: MAN make, including additional tank with a volume of 2000l, mileage: approx. 400,000km. 2) Generator diesel engine Volvo TAD1631GE, power: 485kW, speed: 1500rpm, including exhaust gas turbocharger, intercooler, front radiator, starter, alternator, speed governor, connection housing, intake air filter with fine filter and intake air heating for colder outside temperatures. 3) Stamford HCI544F1 generator, type output (oversized): 670kVA, continuous output: 560kVA. The engine is integrated in the base frame with the fuel tank of the truck (400 l) and the auxiliary tank (2000 l). This makes it possible to produce 10000kWh of electricity at a time. Conditi ...
A Hyfra water recooler is available. Cooling capacity: 5.15kW, max. ambient temperature: 37°C, max. operating overpressure: 29.5bar, refrigerant: R 407c, refrigerant capacity: 2kg, machine dimensions X/Y/Z: approx. 900mm/800mm/1400mm, empty weight: approx. 180kg. Documentation available. On-site inspection is possible.
Four dissolvers from various manufacturers are available. 1) Niemann NLD I, year of manufacture: 1995. 2) Vollrath VDSVY 15, year of manufacture: 1992, shaft length: 700mm, disk diameter: 400mm, tank volume: 400l, tank diameter: 785mm, tank height: 990mm, outlet diameter: 45mm. 3) Vollrath VDSVY 40, year of construction: 1991, tank volume: 400l, speed: 1000rpm, shaft length: 700mm, disk diameter: 400mm, machine dimensions X/Y/Z: approx. 3200mm/800mm/1200mm. 4) Pendraulic WDV 10, speed: 1800rpm, shaft length: 985mm, disk diameter: 275mm, lifting height: 1250mm, machine dimensions X/Z: 560mm/3450mm, weight: approx. 850kg. On-site inspection is possible.
A dissolver basket mill combination machine VMA Getzmann is available. Connected load: 25kVA, flour chamber volume: 4l, container volume range: 75l-750l, product volume range: 50l-400l. The ceramic insert of the flour basket is defective and must be replaced. On-site inspection is possible.
Output: 1000/min, number of cameras: 2. On-site inspection is possible.
Volume flow: 12500Bm³/h, total pressure difference: 40mbar, motor power: 22kW, speed: 3000rpm, machine weight: 1275kg. Components: Dust extraction, water vacuum filter, separator. Including pH value dosing. Documentation available. On-site inspection is possible. Expected to be available from April 2025.
A mobile Vetter gantry crane is available. Load capacity: 1000kg, clear width: 2100mm, height: 3000mm. Documentation available. On-site inspection is possible.
Volume flow: 6300Bm³/h, total pressure difference: 40mbar, motor power: 11kW, speed: 3000rpm, machine weight: 400kg. Components: Dust extraction, water vacuum filter, separator. Including pH value dosing. Documentation available. On-site inspection is possible. Expected to be available from April 2025.
table diameter: 500 mm table load: ? t table height: hor. 235 / Sph. vert. mm groove width: 18 mm total power requirement: - kW weight of the machine ca.: 0,270 t dimensions of the machine ca.: 800640235 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A wet extraction system Ulrich Anlagen und Industrieservice is available. Material: PE/PP/PS/ABS/LDPE/HDPE/MDPE, particle size: less than 1µm, separation efficiency: 97.5%, control system: Siemens S7. Including buffer tank, Almatec AHS 25 heavy-duty membrane pump, MSE 470-30 chamber filter press, working platform, stainless steel filtrate tank and discharge and cross conveyor screw. Documentation available. On-site inspection is possible.
pressure: - t diameter: 3 mm total power requirement: 2 kW weight of the machine ca.: 1 t dimensions of the machine ca.: 1,5 x 1,5 x 2 m rivetting machine Workspace: Ø 3 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A Vollrath multi-shaft mixing plant is available. Container volume: 700l, max. batch capacity: approx. 700kg, agitator disks: 3, agitator disk diameter: 275mm, speed: 2000rpm, motor power: 36kW, stroke: 950mm, machine dimensions X/Y/Z: approx. 2200mm/1250mm/2400mm, weight: approx. 2600kg. Documentation available. On-site inspection is possible.
saw blade diameter: 275 - 315 mm cutting diameter: 80 - 102 mm stroke: - mm total power requirement: 2 kW weight of the machine ca.: 0,4 t dimensions of the machine ca.: 1,5 x 1, 5 x 2 m No. 5230 Cold circular saw with additional gearbox for 4 speeds EISELE VMS II - S - PV ( Typ-Nr. 421 ) Additional gearbox 10/20/40/80 min-1 Cutting speeds 8.5 - 80 m/min Saw blades Ø 275 - 315 mm Space requirement approx. 80 x 90 x 180 cm (plus roller conveyor + fence) Weight approx. 400 kg Working range: Ø 80-102 /flat 160x75/82 Drive: 1,4/1,9 Feed - roller conveyor approx. 2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A lifting, tilting, and sorting system for bulk materials within grid boxes is available. The system lifts the grid boxes approximately 3-4 meters high, tilts them into a transport vibrator, and the parts are then provided to the sorting system in a reduced quantity (feed rate regulation). Load capacity: 1000kg, pressure: 140bar. Documentation available. On-site inspection is possible. Expected to be available from the end of 2024.
saw blade diameter: - mm workpiece-spindlehead motor: 0,18 kW grinding wheel diameter: ? mm total power requirement: 0,18 kW weight of the machine ca.: 200 kg dimensions of the machine ca.: 0,8 0,5 1,6 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
dimension of workpiece: - mm voltage: 230 V : 4 Achsen Anzeige Gerät total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m 4-axis d.r.o. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
volume capacity: max. 2250 m³/h : 2550 pa power capacity: 2,2 kW Suction- Tube: 250 mm Number of working hours: 1450 h power requirement: 2,2 kW Packing: ca. 1200 x 900 x 1600 mm Shipping weight: 250 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 15000 kg height: 790 - 1150 mm width: 1200 mm : ja : 790 - 1150 mm : 120 x 1200 mm Support stand, assembly stand, steel stand, welding table, assembly table, steel trestle, work trestle - Our jack stands are characterized by their stable construction, high load-stable stability and indestructible service life. - galvanized - CE marking - Transport on request The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
diameter: 450 mm faceplate, faceplate chuck, four-jaw chuck, 4-jaw chuck, Facing chuck - 4 jaws - Jaw width 50 x 115 mm - Thickness 85mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
cutting diameter: 350 mm saw band length: 4640 x 34 x 1,1 mm table height: -- mm : 350 mm : 15 - 100 m/min : 4,0 kW : 2800 kg : 2200 x 3200 x 2200 mm Fully automatic band saws with two-column guide for series cuts in particular materials that are difficult to machine and solid material. With this machine, MEP offers you a machine that is technically on the highest level and by using the highest quality materials one is not has an unbeatable, robust and torsion-resistant structure. An extreme Robust saw bow made of gray cast iron ensures the necessary stability impressive cutting results and the strong cast iron columns which the saw arch slides by means of pre-stressed linear guides take care of themselves at maximum load for the highest cutting precision. The modern Machine control (MEP NC 5.0) offers the user maximum ease of use and ensures trouble-free operation. (Check/evaluation/cor ...
saw blade diameter: 370 x 3,0 x 40 mm cutting diameter: 120 mm stroke: -- mm capacity 90 degrees: square: 100 mm capacity 90 degrees: flat: 180 x 100 mm capacity 45 degrees: round: li. 120 / re. 105 mm capacity 45 degrees: square: li. 100 / re. 100 mm capacity 45 degrees: flat: li. 130x100 / re . 130x10 mm capacity 60 degrees: round: 110 mm capacity 60 degrees: square: 90 mm capacity 60 degrees: flat: 90 x 100 mm total power requirement: 1,8 / 2,2 kW weight of the machine ca.: 392 kg dimensions of the machine ca.: 700 x 900 x 1800 mm -The powerful, 2-stage gear was specially designed for cuts in solid material designed -The user has a total of 4 blade speeds for optimal adjustment the material available -The large bearing rotary table with internal table clamping and Precision stops at 0/45/60° ensure quick adjustability miter cuts -The vice with quick clamping (optional is a pneumatic ...
control: SIEMENS 810D turning diameter over bed: 1000 mm centre height: 500 mm centre distance: 2000 mm turning dia. over face-slide: 700 mm spindle bore: 128 mm spindle taper ISO: DIN55027/11 spindle turning speed - stepless: 6.4-1600 U/min tailstock quill taper MT: 6 diameter of quill: 125 mm quill stroke: 280 mm feed - longitudinal/cross: 5000/4000 mm/min rapid traverse longitudinal and cross: 10/5 m/min dimensions of machine: 5600 x 2600 x 2800 mm weight: 9.1 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
with CNC-path-control: HEIDENHAIN type: iTNC 530 for axes: 3 x-travel: 1020 mm y-travel: 560 mm z-travel: 600 mm table surface area: 1000x560 mm table load: 1.35 t tool magazin:: numbers of tools: 40 max. tool diameter: 76 mm max. tool-dia with free toolbox: 125 mm max. tool length: 305 mm max. tool weight: 7 kg milling head: spindle taper:: SK40 spindle turning speed - stepless: 100-10000 U/min Power: 12/18 KW feeds -stepless-: 16000 mm/min rapid motion -longitudinal/cross/vertical: 40 m/min dimensions of the machine ca.: 3x2.3x2.6 m weight of the machine ca.: 6.8 t 3D measuring tracer: RENISHAW OMP40 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 710 mm y-travel: 500 mm z-travel: 500 mm table-size: 1080x580 mm spindle taper: SK40 spindle turning speed range: 10000 U/min tool change unit: 30 weight of the machine ca.: 10 t HEIDENHAIN TNC430 Coolant through spindle www.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 2000 mm y-travel: 550 mm z-travel: 560 mm weight of the machine ca.: 10 t dimensions of the machine ca.: 5.5 x 3.2 x 3.1 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): x mm bore capacity in steel (diameter): x mm throat: x mm throat: x mm bore stroke: x mm bore stroke: x mm POLYHEDRAL DRILLING MACHINE Drilling range: -Square: Spanner opening 3-27mm -Hexagon: Spanner opening 3-32mm Drilling depth: -Square -14mm -Hexagon-13mm Throath150mm Misc accessories More details on www.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding wheel diameter: 300 mm no. of working stations: 2 Stück total power requirement: 1,1 kW weight of the machine ca.: 0.2 t 1x Cup wheel diameter 300mm 1x tangential wheel 260x50mm Drill sharpening device More details on www.marcels-maschinen.ch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
x-travel: 1600 mm y-travel: 900 mm z-travel: 800 mm control: HEIDENHAIN iTNC 530 for axes: 3 table surface area: 1700x850 mm tool magazin:: 30 spindle taper:: SK 40 spindle turning speed - stepless: 100-10000 U/min feeds infinitely variable to rapid traverse: 2-20000 mm/min voltage: 400 V dimensions of the machine ca.: 385x420x325 cm weight of the machine ca.: 18.6 t Coolant through spindle: pressure: 18 bar 3D measuring tracer: RENISHAW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
maximum number of results exceeded
please refine your search
