natural gas engine used for sale

Key data: 250 KW, 310 kVA, 400 V

UK Power Generators LTD have Containerised Package of 250kW Gas Generator for sale, see below the technical specification of the unit: Make: Scania Model: 6R20.1BO Rated Output: 250 kWe Fuel : Gas Serial No: 003837 YOB: 2014 Volt: 400 V Frequency: 50 Hz Speed: 1500 RPM Type: Containerised The unit has been maintained throughout its life and available on request upon inspection. The Containerised Package include the exhaust silencers, air ducting and table cooler radiator (pictures are attached). For any further enquiry and pricing information, feel free to reach us at: Enquiriesukpowergeneratorsltd 00447956518924

Machine type MIG/MAG welding system Make Merkle Type RedMIG 1600 K Connection voltage 1 x 230 volts Setting range 25 - 160 amperes Switch-on time 30% ED at 160 amperes 60% ED at 130 amperes Current setting 7 switching stages Cooling transformer by built-in fan Cooling burner gas-cooled Design mobile compact system Wire feed 4-roll drive Hedging 16 Ampere Dimensions L x W x H 800 x 460 x 620 mm Weight 65 kg Age 12 months Condition workshop-tested, very good, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 157 G, 3 mtr. Long 1 piece ground cable 4 mtr long, 25 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire, D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece glass 90 x 110 mm white 1 piece protective glass 90 x ...

LHS Lagertechnik, supplier of new and used storage technology. We provide you with racking systems, industrial trucks, accessories and other warehouse inventory. In this ad, you will buy as follows: - Nilfisk SR1500 HP Sweeper - Serial number: 50602935 - Drive GAS - Hours: 470 - Operating length: 1:800 mm - Operating width: 1,200 mm - NEW UVV -Headlight Device works and can be tested on site Self-pick-up welcome / Free loading / Shipping can be organized nationwide / Please inquire about your transport costs. Sale of used goods without guarantee and warranty. Errors / prior sale of used goods expressly reserved.

Centrifugal compressor in landfill gas use. Technical data sheet located as an attachment. The compressor is located in a very good condition, is until end of July 2018 in the operation and is very robust (casing). Pressure difference 180mbar and 15 kW drive motor. Radial blower used for landfill gas utilization. Technical specification see attached data sheet. The blower is in good technical condition and still in operation on a bio-gas plant in Germany untill end of July 2018. Pressure drop 180 mbar with 15kW electrical drive.

FOR SALE... OVERHAULED TURBOCHARGERS ABB VTR 254-11 & BBC VTR 214-11 TO WHOM IT MAY CONCERN; WE VE BELOW LISTED OVERHAULED & REPORTED TURBO CHARGERS AT OUR STOCK. READY TO TRANSPORT AND USE... ABB VTR 254-11 HZTL 428765P2 nNmax 523 nBmax 497 tMmax 680 C tBmax-650 C SFUSO1 YEAR OF BUILT 2010 BBC VTR 214-11 NoHT 399285 their 635 Tmax 680 V 01113 R 012 H 04109 W 12206 E 03221 U 023 YEAR OF BUILT 2012 IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CIONTACT WITH US. Capt. Ayhan Ugurluba BEST regards; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 90 Mobile: + 905556084850 aliagamarine.com TURKEY

Machine type MIG/MAG welding system Make MERKLE Type RedMIG 3000 D Connection voltage 3 x 400 volts Setting range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current setting 14 switching stages Cooling transformer by built-in fan Cooling burner gas-cooled Execution of mobile industrial plant with separate DV case Wire feed 4-wheel gearbox DV 26 Hedging 16 Ampere Dimensions L x W x H 940 x 445 x 1,040 mm Weight 140 kg Special accessories VB-cable 1.6 mtr. Long Age 9 months Condition very good, as new Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece pro ...

Machine type MIG/MAG inverter welding system Make Merkle Type MobiMIG 320 K Plant No. 118.362 Connection voltage 3 x 400 volts Setting range 25 - 320 amperes Switch-on time 40% ED at 300 amperes 60% ED at 270 amperes 100% ED at 240 amperes Current setting infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Design portable assembly system Wire feed gearbox 4-wheel gearbox DV 26 Hedging 16 Ampere Dimensions L x W x H 600 x 300 x 565 mm Weight 32 kg Age 6 months Condition workshop-tested new incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 pie ...

Second-hand Hybrid forklifter LPG gas and petrol Loading capacity 3,000kg Engine K25 Japan Long forks 1.820mm lifting height 3,000mm solid tyres Colour red Including.: Duplex mast, side shifter, seat belt, rain cover, toolbox, manual

Number: VH503 Number: 1 piece Control cabinet for the continuous gas analysis for measuring gas preparation Cabinet disc is available and whole! Delivery possible by arrangement Make: ABB Type: unknown Extract of the component list: ABB Measuring gas conveying unit Advance SCC-F ABB Measuring gas cooler Advance SCC-C RITTAL Filter Fan SK 3326100 WINKLER Filter for electrically heated sample lines AF2055/06/200 DURAG 2 unit of operation & evaluator for combination probes D-RX 250 FESTO 2 valve & filter blocks Collecting container among other things, Dimensions:. 2000x800x650 mm (HxWxD) Weight:.. approx. 180 kg

Sealing plates 1.5 x 1.5 m from 2 to 8 mm thickness. Asbestos-free. Made in Germany Price â?¬ 2,00 / kg

10 tons Gaz hose (for house connection) 8 mm and 12 mm Complete roles Made in Germany â?¬ 2,00 / kg

GEA Plate heat exchanger NT50T CDS-10 with 10 plates in very good condition Material: 1.4405 Min./Max. permissible pressure: 0 bar / 6 bar (both sides) Min./Max. permissible temperature: 0.0 °C / 100 °C Test pressure: 7.8 bar Volume: 0.82 / 1.03 L Kerb weight: 83 kg Width: 320 mm Height: 670 mm Depth: 600 mm Connections: 2x Flange DN50 2x Flange DIN 11851 (milk pipe thread) Number of plates: 10 Last refrigeration/heat medium: water-glycol mixture Seals: EPDM

GEA Plate heat exchanger NT50T CDS-10 with 10 plates in very good condition Material: 1.4405 Built: 2007 Min./Max. permissible pressure: 0 bar / 6 bar (both sides) Min./Max. permissible temperature: 0.0 °C / 150 °C Test pressure: 7.8 bar Volume: 0.82 / 1.03 L Kerb weight: 88 kg Width: 320 mm Height: 670 mm Depth: 600 mm Connections: 2x Flange DN50 2x DIN 11851 (milk pipe thread) Last heat medium: steam Seals: EPDM

GEA plate heat exchanger VT10 CDS-16 with 10 plates in very good condition Built: 03/2006 Min/Max permissible pressure: 0 bar / 10 bar (both sides) Min./Max. permissible temperature: -10 °C / 100 °C Test pressure: 13 bar Volume: 3.0 / 3.3 L Kerb weight: 133 kg Width: 290 mm Height: 920 mm Depth: 570 mm Refrigeration/heat medium: propylene glycol Connections: 4x Pipe nipple DN 50 Device can be inspected at any time in 76694 Forest upon request.

51 MW - CCGT comprising 3 x 12 MW Solar Gas Turbine generator and 1 x 15 MW steam turbine generator Model : TITAN 130 Capacity : 12 MW Voltage ; 11 KV / 50 Hz Qty : 3 sets Titan 130 + 1 set STG Year : 2012 Running hr : 6000 hrs since new

Complete 48 MW Westinghouse W251-B11A Gas Turbine with a Brush electric generator, 3000 rpm, 50 HZ, 11.5 KV, may be modified as Dual Fuel GT ied

Key data: 1000 , 1250 , 400

WAUKESHA P9390GL 1 MW 400V / 50 Hz / 1000 rpm, only 6000 hrs, year 1996, dismantled from Landfill station

Key data: 4000 , 5000 , 10500

14 nos. used MWM gas generator TCG2032V16 4 MW 10.5KV / 50 Hz, year 2011 About 40,000-44,000 hrs.

Machine type MIG/MAG welding system Make MERKLE Type RedMIG 2800 K Connection voltage 3 x 400 volts Adjustment range 25 - 280 amperes Switch-on time 30% ED at 280 amperes 60% ED at 210 amperes Current setting 14 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 4-wheel drive DV 26 Fuse 16 Ampere Dimensions L x W x H 800 x 460 x 655 mm Weight 80 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch 3 mtr. Long 1 piece ground cable 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece of protective glass 10 DIN 1 piece of white glass 1 piece spare part box, kpl ...

Machine type MIG/MAG welding system Make Merkle Type RedMIG 1600 K Connection voltage 1 x 230 volts Adjustment range 25 - 160 amperes Switch-on time 30% ED at 160 amperes 60% ED at 130 amperes Current setting 7 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 2-roll drive Fuse 16 Ampere Dimensions L x W x H 800 x 460 x 620 mm Weight 65 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 157 G, 3 mtr. Long 1 piece ground cable 4 mtr long, 25 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 roll of welding wire, D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece of lens 90 x 110 mm white 1 piece of protecti ...

Machine type MIG/MAG welding system Make MERKLE Type RedMIG 2000 K Connection voltage 3 x 400 volts Adjustment range 25 - 200 amperes Switch-on time 30% ED at 200 amperes 60% ED at 140 amperes Current setting 7 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 2-roll drive Fuse 16 Ampere Dimensions L x W x H 800 x 460 x 655 mm Weight 70 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch, 3 mtr. Long 1 piece ground cable 4 mtr. Long 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece of protective glass 10 DIN 1 piece of white glass 1 piece spare part box ...

A complete power plant consisting of 3 JEBANCHER units is now available. Below are the details: 2x Engines Model J616C - Power: 2519 kVA (2.519 MW each) - Overhauled (E60) in 2011 - Operating hours since overhaul: 20,503 hours - Manufacture date: 1997 - Serial numbers: 1200959 / 1200956 1x Engine Model J320 GS S04 - Power: 1366 kVA (1.366 MW) - Overhauled (E60) in 2011 - Operating hours since overhaul: 19,059 hours - Manufacture date: 1997 - Serial number: 1200954 Total power capacity: 2 x 2.519 MW + 1.366 MW = 6.404 MW Scope of supply includes: - XT3 Diane control panel - GEC ALSTHOM transformers: 3 units (2x 2500 kVA, 1x 1600 kVA) - Gas line - Heat exchanger - Smoke exchanger - Pumps - Table cooler (radiators) - Oil tank Location: Paris, France For more information, please feel free to contact us.

Fronius magicwave 2600, with wire feeder can be used for the robot welding. Machine is in great working condition, equipped with longines controls, wire feeder and welding gun connections for the robots.

Intelligent Gas Flow Meter, 5860S/BC1GA0BA1B1, Brooks Instrument, new We have set the lowest price for the new part on the market. We still have several identical and other such devices, but the amount is ending. Buy more than 1 piece there is still a great discount. As good as new in original packaging! The part was bought from a spare parts warehouse of a company and has never been in operation, is completely as good as new and in its original packaging. - High-quality mass flow meter for gas - Max. 300 bar Functional guarantee! We cannot provide a conventional warranty and warranty for second-hand parts. Since we know that the device works, we give you a functional guarantee when you purchase it. If the device does not work within 6 months of purchase, you can return the goods and we will refund the purchase price.

Key data: 2700 KW, 11000 V

Jenbacher 620 Containerised Gas Generating Set with 2.7 MW of Output Power Manufacturer: Jenbacher Model: J620 Year of remanufactured: 2023 Voltage: 11kV Power Output: 2.7 MW Frequency: 50 Hz Speed: 1500 RPM Additional Features for these Units: Brand New Units: All units are newly remanufactured. High-Quality Containers: Premium containers with diamond deck flooring. Exterior Construction: Durable green steel casing. Ventilation: Large louvered vents on upper sections for optimal airflow. Access Doors: Secure entry doors with labelled panels for easy identification and access. Exhaust Stacks: Large black exhaust silencers for noise reduction and efficient emission handling. Foundation: Elevated on sturdy metal supports for stability and ease of maintenance. Table Cooler Radiators: For efficient cooling. Exhaust Silencers: For noise emissio ...

Machine type MIG/MAG inverter welding system without BiPower Make Merkle Type MobiMIG 280 K Plant No. 123.035 Connection voltage 3 x 400 volts Adjustment range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 4-wheel transmission DV 26 Fuse 16 Ampere Dimensions L x W x H 470 x 255 x 545 mm Special accessories ColdMIG welding process, e-welding MIG soldering, filler wire welding Weight 27 kg Age 2 years Condition workshop-tested, very good, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer Argon w ...

Key data: 2188 KW, 2702 kVA, 6300 V

CHARACTERISTICS OF GENSET ✓ Jenbacher J616 G.S-NL | YOM 2004 | Power 2,188 kWe | Natural gas Generator AVK 2,702 kVA | 6,300 V | 50 Hz | cosφ= 0.8 AVAILABLE EQUIPMENT ✓ Genset with auxiliaries included Diane XT control panel and synchronizer ✓ Generator high voltage switchgear 6.3 kV, protections cabinet ✓ Lub oil system, gas valves, crane, radiators HT circuit, cooling towers LT circuit, heat exchangers, control valves, water and oil pipes, exhaust silencer. ✓ Documentation related to the installation. CURRENT STATUS OF PLANT ✓ Plant stopped in 2023 due to commercial reasons. ✓ Genset crankshaft it is turned periodically. ✓ Run test is possible but with some associated costs: necessary filling lub oil circuit with new clean oil, and some minor checkings. ✓ Genset was always maintained under LTSA by Jenbacher ✓ Genset history: No failure ...

Key data: 2745 KW, 3400 kVA, 6300 V

CHARACTERISTICS OF GENSET ✓ Jenbacher J616 G.S-NL (GS-J11 engine) | YOM 2016 | Power 2,745 kWe | Natural gas Generator Leroy Somer 3,400 kVA | 6,300 V | 50 Hz | cosφ= 0.8 AVAILABLE EQUIPMENT ✓ Genset with auxiliaries included Diane XT control panel and synchronizer ✓ Generator high voltage switchgear 6.3 kV ✓ Step-up transformer EFACEC 6.3/15 kV 3,500 kVA (YOM 2017) | Auxiliaries transformer ✓ Lub oil system, gas valves, crane, radiators HT circuit, cooling towers LT circuit, heat exchangers, control valves, water and oil pipes, exhaust silencer. ✓ Documentation related to the installation. CURRENT STATUS OF PLANT ✓ Plant stopped in 2023 due to commercial reasons. ✓ Genset is kept hot and crankshaft it is turned periodically. ✓ Genset is ready to run. ✓ Genset was always maintained under LTSA by Jenbacher ✓ Genset history: No failure ...

Key data: 400 KW

MAN E2842 LE322 Complete TRIGENERATION Plant Hours 14,500 Year 2017 Fuel NAT GAS Voltage: 400 V Scope of supply: The plant includes Engine, Alternator, Prefabricated Room, Intercooler, Skid, Aircooler, Gas Ramp, Radiator, Heat Exchanger, New / Exhaust Oil Exchange System, Exhaust Gas Chimney, Control Panel (Siemens), electrical panels, silencer, gas compressor, metering systems, pumps, chiller, afterburner, various stainless steel pipes. Capacity 401 kW. It is currently limited to 355 kW to work with low emissions. Also available in a cogeneration-only setup (180,000 €). Available for sale from Gas Engine Exchange. Please check our full range of equipment at gasengineexchange.com.

Key data: 8000 KW, 7425 kVA, 11000 V

CHARACTERISTICS OF GENSET ✓ Wärtsila 16V32SG | YOM 2015 | Real power of the motor is 8.000 kW (in plate) | Effective design power was reduced to 7.400 kW in order to get adapted to legal power stated at permits (there was a gas turbine in this plant before installing this Wärtsilä genset) | Fuel: Natural gas ✓ Generator ABB 7,425 kVA | 11,000 V | 50 Hz | Cos = 0.98 AVAILABLE EQUIPMENT ✓ Genset with auxiliaries included control panel and synchronizer ✓ Generators high voltage switchgear 11 kV, protections cabinet ✓ Lub oil system, gas valves, crane, radiators HT circuit, cooling towers LT circuit, heat exchangers, control valves, water and oil pipes, exhaust silencer. ✓ Main step-up transformer SIEMENS 8000 kVA | 11 / 15 kV | YOM 2015 ✓ Auxiliaries transformer EFACEC 400 kVA | 0.4 / 15 kV | YOM 2009 ✓ Heat recovery boiler for steam generation | Y ...

Key data: 1487 KW

CUMMINS GQSK60 Gas Generator – In Excellent Condition! Looking for a reliable, powerful, and immediately available gas generator? The CUMMINS GQSK60 is the perfect choice for your needs. This generator is in excellent condition and has low operating hours. CUMMINS GQSK60: Excellent condition Low operating hours: Enjoy efficient operation with plenty of potential for many years of trouble-free use. Immediately available: No long wait times Fully equipped: The generator comes complete and ready for installation, including the control panel, breaker, gas line, exhaust silencer, and cooling system. Simply connect the gas and power supply. GAS POWER HOLLAND

Engine Make Jenbacher Engine Type JGS 620 GS Power KW/RPM 3044/1500 Fuel Natural gas Generator Voltage 10500 V Hz 50 Year of Manufacturing 2011 Running Hours 42666 30k service done at 32.000 hours GAS POWER HOLLAND 00316 38 63 90 71 whatsapp

Machine type MIG/MAG inverter welding system without BiPower Make Merkle Type MobiMIG 280 K Connection voltage 3 x 400 volts Adjustment range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 4-wheel transmission DV 26 Fuse 16 Ampere Dimensions L x W x H 470 x 255 x 545 mm Special accessories ColdMIG welding process, e-welding MIG soldering, filler wire welding Weight 27 kg Age 12 months Condition workshop-tested, very good, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer Argon with 2 pressure gau ...

Key data: 2679 , 6300

Available One complete Jenbacher 616 plant from 2016, with 33,000 operating hours. All maintenance has been performed by the official service. The engine has a power output of 2,679 kW and an electrical output voltage of 6,300 V. The generator brand is Leroy Somer. Scope of supply includes: Genset, cooling system, transformer, DIANE XT4 control system, fans, generator circuit breaker, gas train, low and high temperature pumps and heat exchangers, silencer, and heat recovery system from exhaust and oil. The plant is disassembled and ready for loading at our warehouse. Boroscope inspection, maintenance records, and inspection reports are also available. You are welcome to visit and inspect the assets at any time.

Key data: 812 KW, 400 V

Complete 812kW containerised CHP Himonsia / Siemens HGS-810 T5 LPG generating set Make and model: Himonsia / Siemens HGS-810 T5 LPG Scope of supply: 40ft Container (67dBA1m), Engine (Siemens), Alternator (Stamford), Control Panel (Comap Controller), Remote Radiator and Heat Exchanger. The Engine is currently being rebuilt with 4 x heads already replaced and the following spares available with the unit: 7-cylinder head gasket kits 1-cylinder head 1- exhaust manifold section 1-water temperature sensor Maximum service cost estimated at £30,000. Available for sale from Gas Engine Exchange . Please check our full range of equipment at gasengineexchange.com.

Machine type MIG/MAG inverter welding system Make Merkle Type MobiMIG 180 K Connection voltage 1 x 230 volts Adjustment range 25 - 180 amperes Switch-on time 20% ED at 180 amperes 60% ED at 110 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 2-wheel transmission Fuse 16 Ampere Dimensions L x W x H 450 x 210 x 480 mm Special accessories ColdMIG welding process E-welding, MIG soldering Filling wire welding Weight 17 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 157 G, 3 mtr. Long 1 piece ground cable 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-200 coil, 5 kg 1 can  ...

Forty two (42) Quality Used Cummins/Aggreko NCH20-QSK60G22, Dual Frequency 1875 kVA, 480v. 60 Hz. or 1875 kVA, 400v. 50 Hz. Natural gas generator sets. These 1875 kVA units are set for continuous an parallel to gird IPP applications. These units have less than 5000 hours of use since new. The generator is a gas engine driven alternator with control electronics, mounted on a bedplate and housed within a custom-built 20ft stackable container. The standard package is composed of the following: Alternator and engine assembly, Pressurized oil system, Automated control system, Instrumentation, Safety provisions, Engine cooler pack, Silencer, Gas lines including external Low Pressure Gas Train & internal Solenoid Valve The engine and alternator are integrally mounted. This assembly is isolated from the bedplate base by rubber isolation mounts. A 20ft containerised Gas Cooling Module (G ...

Machine type MIG/MAG inverter welding system with bi-power setup Make Merkle Type MobiMIG 280 K - BiPower Connection voltage 230/400 volts Adjustment range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 4-wheel transmission DV 26 Fuse 16 Ampere Dimensions L x W x H 470 x 255 x 545 mm Special accessories ColdMIG welding process, e-welding MIG soldering, filler wire welding Bi-Power Setup Weight 27 kg Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reduc ...

Machine type MIG/MAG welding system Make CEBORA Type MIG STAR 550 S Plant No. 991502 Connection voltage 3 x 400 volts Setting range 40 - 500 amperes Switch-on time 60% ED at 500 amperes 100% ED at 390 amperes Current setting 32 switching stages Cooling transformer due to built-in fan Cooling burner water-cooled Execution of mobile industrial plant with separate DV-case Wire feed gearbox 4-wheel drive Fuse 32 Ampere Dimensions L x W x H 1,000 x 500 x 1,250 mm Weight 190 kg Age approx. 25 years Condition workshop-tested, good, incl. UVV test protocol Special accessories 3 x throttle pick-ups Scope of delivery Welding system with the following accessories: 1 piece welding torch 3 mtr. Long 1 piece ground cable 1 piece pressure reducer Argon with 2 pressure gauges 1 piece spare part box kpl. Equipped 1 piece user manual Warr ...

Machine type MIG/MAG welding system Make Merkle Type CompactMIG 220 K Connection voltage 3 x 400 volts Setting range 25 - 220 amperes Switch-on time 40% ED at 220 amperes 60% ED at 170 amperes Current setting 7 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 4-wheel gearbox DV 26 Fuse 16 Ampere Dimensions L x W x H 870 x 480 x 740 mm Weight 90 kg Special Accessories Display Automatic wire Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 157 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield  ...

Natural Gas Power Plant 58.3 MW / 50 Hz Wartsila 6 × 20V34SG with Auxiliaries This power plant was originally built by Wärtsilä in 2011 as a turnkey project without heat recovery boilers. Later, the owner added 4 × 3.7 MW / 18 bar exhaust gas steam boilers with auxiliaries, which are available as optional items. The plant was in operation until 2017, accumulating approx 21000 operating hours per engine. All scheduled services were performed by Wärtsilä Service, including the 16,000-hour and 24,000-hour services, completed just prior to dismantling in 2021. This ensures that the gensets are fully maintained and do not require servicing before re-commissioning. After shutdown, all equipment—including cables, pipes, and OEM modules—was professionally dismantled, tested, packed for transportation, and placed in storage. Control cabinets are stored in a heated warehouse, wh ...

Machine type MIG/MAG welding system Make MERKLE Type CompactMIG 400 DW Connection voltage 3 x 400 volts Adjustment range 25 - 400 amperes Switch-on time 35% ED at 400 amperes 60% ED at 310 amperes 100% ED at 230 amperes Current setting 14 switching stages Cooling transformer due to built-in fan Cooling burner water-cooled Execution of mobile industrial plant with separate DV-case Wire feed 4-wheel gearbox DV 26 Fuse 16 Ampere Dimensions L x W x H 940 x 445 x 1,040 mm Weight 170 kg Special accessories display, automatic wire, VB cable 1.6 mtr. Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 504 W, 3 mtr. long 1 piece ground cable 4 mtr. long, 70 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 ...

Machine type MIG/MAG welding system Make MERKLE Type CompactMIG 400 K Connection voltage 3 x 400 volts Adjustment range 25 - 400 amperes Switch-on time 35% ED at 400 amperes 60% ED at 310 amperes 100% ED at 230 amperes Current setting 14 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Execution of mobile industrial plant Wire feed 4-wheel gearbox DV 26 Fuse 16 Ampere Dimensions L x W x H 940 x 480 x 760 mm Weight 140 kg Special accessories display, automatic wire Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 307 G, 3 mtr. long 1 piece ground cable 4 mtr. long, 70 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non ...

Key data: 1560 KW, 4160 V

Introducing the MWM TCG 2020 V16K generator, a powerhouse of energy efficiency and reliability. Built in 2010, this generator is in pristine condition, unused and ready to deliver exceptional performance. With a rated power of 1418 kW and the ability to run on a variety of gases, including natural gas, biogas, mine gas, sewage, or landfill gas, it offers versatility like no other. Equipped with a Marelli Generators alternator, this generator boasts a power output of 1560 kW, operating at 4160 V with a speed of 1500 RPM and a frequency of 60 Hz. Weighing 16500 pounds, this robust machine is located in the USA and is competitively priced for your convenience. For more information on this top-tier MWM generator, contact us

Machine type Electrode inverter welding rectiveror Make Merkle Type LiteARC 180 Connection voltage 1 x 230 volts Adjustment range 20 - 170 amperes Switch-on time 25% ED at 170 amperes 60% ED at 130 amperes 100% ED at 115 amperes Current adjustment infinitely variable max. weldable material thickness 4 mm Cooling inverter by built-in fan Version of portable assembly line Fuse 16 Ampere Dimensions L x W x H 360 x 140 x 230 mm Weight 5 kg Age 12 months Condition workshop-tested, very good, as new incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece ground cable 1 piece electrode cable 1 piece hand shield 1 piece of lens 90 x 110 mm, white 1 piece protective glass 90 x 110 mm, 10 DIN 1 piece slag hammer, heavy version 1 piece steel wire brush, 2-row 1 piece mains plug 230 V, ful ...

Machine type Electrode inverter welding rectiveror Make Merkle Type LiteARC 160 Connection voltage 1 x 230 volts Adjustment range 15 - 160 amperes Switch-on time 25% ED at 150 amperes 60% ED at 90 amperes 100% ED at 80 amperes Current adjustment infinitely variable max. weldable material thickness 4 mm Cooling inverter by built-in fan Version of portable assembly line Fuse 16 Ampere Dimensions L x W x H 360 x 150 x 240 mm Weight 6 kg Age 12 months Special accessories Carrying strap Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece ground cable 1 piece electrode cable 1 piece hand shield 1 piece of lens 90 x 110 mm, white 1 piece protective glass 90 x 110 mm, 10 DIN 1 piece slag hammer, heavy version 1 piece steel wire brush, 2-row 1  ...

SUMERA MOTOR SMG-100LG-S gas generator was built in 2018 in Poland by SUMERA MOTOR Sp. j. The machine, which is powered by natural gas, ensures uninterrupted operation of machinery and industrial systems in the event of power cuts or in conditions where electricity cannot be supplied. All components of the machine, including the 100 kVA motor, are located inside a soundproof enclosure that significantly reduces noise levels. The SMG 100LG-S generator weighs 1690 kg. Technical specifications of the SUMERA MOTOR SMG-100LG-S gas generator - fuel type: natural gas - rated power: 100 kVA (80 kW) - rated current: 144.6 A - rated voltage: 230/400 V - rated frequency: 50 Hz - rated power factor: 0.8 cosφ - performance level: G3 - degree of protection: IP 44 - maximum operating temperature: 40°C - weight of the SUMERA MOTOR machine: 1690 kg

core engine Centaur 50. The turbine and associated gearbox have been completely base overhauled after last operating and are a ready-to-install for a zero-hour turbine exchange. After the overhaul, there was no active operation / no installation. The turbine and gear box Sale Solar Centaur 50 Base overhauled core engine: Manufacturer Solar Turbines - Type CENTAUR 50 SoLoNox - Year of construction 2022 Zero-hour core turbine and gearbox - Electrical output 4,040 kWel - Speed 14,944 rpm 50Hz - Fuel Natural gas H - Design temperature 15° C - Turbine inlet temperature 665 °C (1.229 °F) - Gearbox with zero operating hours - Turbine control Solar TTS4

Gas Engine Generator Set (CHP/BHKW) MAN for natural gas Model E2866E 95 kWe Spec number 524806 Serial number 27093890484901 Stamford generator UC1274E2 400V/50Hz, 140 KVa 202 Amp year 2000 Serial number 0117910/02 Scope of delivery: - Generator set - Control panel

Gas Engine Generator Set (CHP/BHKW) Waukesha for natural gas Model H24GLD 330kWe Serial number 80371/01 Stamford generator HC1534C2 400V/50Hz, 500 KVa 721 Amp year 2005 Serial number C145320 Scope of delivery: - Generator set - Control panel - Gasline section as displayed - Exhaust gas cooler as displayed