mw 115 used for sale

Key data: 1150 mm, 900 mm, 600 1/min

Basic machine data Used CNC lathe from HWACHEON Make: HWACHEON Type: VT 1150 M Year of Make: 2008 Condition: Very good Control: Name: FANUC 0iTC Travels: x-travel: 610 mm // z-travel: 950 mm Technical data: • Spindle: 600 rpm • 3-jaw chuck ⌀ 1270 mm • Turning diameter: 1150 mm • Turning length: 900 mm • 12-station turret • BMT 85 tool holder • Tool drive: 3000 rpm • Rapid traverse: x = 24 m/min y = 20 m/min • Tool magazine: 12 stations (Capto C8) • Chip conveyor • IKZ (internal coolant supply) • Machine is sold with complete tool package The machine is in a very good condition – hardly used. Machine has only 3269 PGM hours Prior sale is reserved. No liability is assumed for the technical information provided here. The legal provisions apply.

The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Transnorm roller conveyor TS 2800 sorter switch 1980-1250-1150 RA1999 Make: Transnorm Roll width (RB): 1150 mm Nominal/outer width (NB): 1250 mm Length: 1980 mm Diameter rollers: 50 mm distance between rollers: 76 mm Roller conveyor motor: 2x SEW drive motor Angle of the rollers is adjusted pneumatically (see pictures) conveying speed: approx.1,73m/s maximum recommended box/package width: 400 mm Theoretical sorting speed at 600 mm crate length: ca. 4250/h Included: Side guide included on one side Control valve Optionally available: Supports Side guides on both sides Conversion to box width up to 500 mm Barcode scanner Control system (stand-alone unit) System optimization (e.g. replace valves, dual solenoid valve, forward conveyors, frequency converter) for higher flow rate 6000 and more Translated with

Digital Programs TSC, Colour Display, Chromed Air Table, Chromed Side Air Tables, Light Bariers, Standard Accessories

SPECIFICATIONS: Value protection safe with key External dimensions: 550 mm x 500 mm, height: 1150 mm Weight: 285 kg Resistance level: I

swing diameter: 370 - 800 mm weight of the machine ca.: 650 kg dimensions of the machine ca.: 20,41,3 m Open steady rest / setting block - fixed with 4 quills Bed width approx. 360 mm Total base width approx. 720 mm Centre height approx. 500 mm Space requirement approx. 1950 x 400 x 1300 mm Weight approx. 650 kg Working range: approx. Ø 370 - 800 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Schneidmaschine - Guillotine Schneider Senator Senator 115H Year 2003 - Serial-No. M-115H-013-04/10-03 Schnittbreite max. 1150mm / Cutting width max. 1150mm Programm - Duisplay / Program - Display Lufttisch - Chromtisch / Light guard - chrome table CE-Zeichen-Zulassung / CE Certificate Elektr. Anschluss / Power supply 3 Phase 380V - 10A Ersatzmesser / Spare knives Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Key data: 600 mm, 400 mm, 90 mm

Electro-Permanent Magnet Clamping Plate Type 1150V-40/60-14

Connected load 380V 6.8kW 12A with sliding table 1100 mm Table size 1100 x 900 mm Height adjustment with hand crank Integral stop jaws Stops individually adjustable via Siko counter Aigner milling cutter protection device Suction 1x120 1x150 mm Speeds: 2900/4400/6000/8000/10000 rpm

filtration performance: . l/min fleece width: . mm temperature: . °C The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Engine Brand: SWEDIC, Condition: NEW, Engine Cooling Type: Radiator Cooled (std) , Engine Color: Yellow , Engine Condition: New , Turbo Type: None Mounted , Exhaust System: Dry , ECU Present?: no , Starter Voltage: 12 Volt , Injection Type: Mechanical Fuelpump , Generator KVA: 10.5 , Generator Hz: 50 , Generator Volts: 230/400 , Generator Amps: 13.5 , Generator Fases: 3 Fases , , https://www.hamofa.com/stock/generators/swedic-sw-11500-generator-10kv a-new/322, , = More information =, , Year of construction: 1010, Empty weight: 205 kg, Type number: SW-11500 GENERATOR 10KVA

Engine Brand: CATERPILLAR, Condition: USED, Nominal Power @ Nominal Rpm: 783 Kw, Engine Injection Type: DIRECTE INJECTIE , Engine Aspiration Type: TURBO INTERCOOLER , Air Cooling Type: WATERGEKOELDE INTERCOOLER , Nominal Rpm @ Nominal Power: 2100 Rpm, Engine Cooling Type: Radiator Cooled (std) , Engine Color: Yellow , Flywheel Housing SAE: SAE 00 , Flywheel SAE: Unknown , Working Hours: 6873 Hour(s), Turbo Type: Watercooled , Exhaust System: Watercooled , ECU Present?: no , Injection Type: Mechanical Fuelpump , , https://www.hamofa.com/stock/diesel-engines/caterpillar-3412c-9xf-1156 846-used/559, , = More information =, , Type: Engine, Type number: 9XF-1156846

SMG 320 cold forming press for sale. Year of build 1981 Model HPU 315-1300/1150 The machine has a crack in the head piece. Drive power: 2 x 55 KW Oil volume of one tank filling 3800 liters Maximum ram force: 3200 KN Drive cylinder: 3 pieces Cylinder 1: 2000 KN Cylinders 2+3: 600 KN each maximum adjustment: 310 mm Find more here - / Contact us at -

Description Conical Twin Screw Extruder Screws Diameter 45 - 97 Screws Length 390 Barrel zones 3 Nr.1 vent Thermoregulated screws Motor power 15,4 kW Forced feed

Robosoft 411-1153 / 412-1240 / 413-0800

Inclined bucket mixer Manufacturer FMW Type 115200/21H475.1 Capacity 50 litres Material: Stainless steel heated, double jacket

Toyota BT Quick Lift pallet truck 2300kg 1150 mm RA2231 Manufacturer: Toyota Fork length: 1150 mm Fork width: 156 mm Carrying surface width: 520 mm Maximum load capacity: 2300 kg Lifting range: 85 - 200 mm With quick lift, 2x pumping is sufficient to be off the ground, with a maximum load of 150 kg Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

weight max. in kg: 2500 kg fork length: 1150 mm stroke height: min 85, max 200 mm : 155 mm length in width: 540 mm number of wheels: 4 vorne, 2hinten tire equipment: PU/Pu fork arm (length x width x thickness): 1150 x 155 x 50 mm weight of the machine ca.: 0,068 t dimensions: 1,5 x 0,54 x 1,21 m SPECIAL PRICE ! - metered lowering of heavy loads - low maintenance hydraulic unit in steel version - Rounded fork tips for more safety when entering the pallet - Hard chromed piston rod and overload valve - Steering and load rollers ball bearings, for easy running even under load The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A Silex continuous baking and deep-frying oven is available. Production capacity: approx. 1000 portions/h, processes: frying/baking, output: 20kW, machine dimensions X/Y/Z: approx. 4100mm/1200mm/1700mm, weight: approx. 900kg. Documentation available. On-site inspection is possible.

thread splicer machine for veneer model KUPER FW 1150 second hand machine volt. 380/50

Key data: 8000 mm, 3 mm

Machine is in stabillier welded construction with 9 columns, 9 clamping cylinders and 36 coupling joints K38 mounted on a base frame The machine has the following equipment: CNC 8000 Control with Touch Screen TFT Color Display 17 Inch Attachment rail, brush table, upper beam with water seam groove Oil filling, fastening and levelling material, emergency stop rail via the Full length of the machine, integrated emergency stop operation in the foot pedal for upper and lower Bending beam, 2nd foot pedal for 2-man operation, upper bolster protection 2 short-part clamping fingers Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Working length: 8000 mm Sheet thickness max. steel: 3.0 mm Sheet thickness max. aluminium: 4.0 mm Sheet thickness max. VA: 2.0 mm Back gauge (max:.) 1150 mm Back gauge (min.): 150 mm Colo ...

Split nut for Idra die casting machine, TR330x10, 11505195.10, Druckguss Servive, new Special price ! If you have a VAT number, we will gladly issue an invoice without VAT. Condition new The nut is new and fully functional. Split nut, Tr330x10, 2x590x275x285mm high. Approx. 540kg With sliding bushes The nut has been preserved by us. The goods can be viewed, inspected and collected from us at any time. We will also be happy to send you a sketch of the design or deliver the goods to your address. Attention: We offer various columns, adjusting nuts, tie bar expansion nuts and 2-piece nuts from: IDRA D330, D300, D260, D250, Oleopress/OP Die Casting: D285, D250, Frech: D375, D330, D300

Engine Brand: SWEDIC, Condition: NEW, Engine Cooling Type: Radiator Cooled (std) , Engine Color: Yellow , Engine Condition: New , Turbo Type: None Mounted , Exhaust System: Dry , ECU Present?: no , Starter Voltage: 12 Volt , Injection Type: Mechanical Fuelpump , Generator KVA: 10.5 , Generator Hz: 50 , Generator Volts: 230/400 , Generator Amps: 13.5 , Generator Fases: 3 Fases , , https://www.hamofa.com/stock/generators/swedic-sw-11500-generator-10kv a-new/437, , = More information =, , Empty weight: 205 kg, Type number: SW-11500 GENERATOR 10KVA

Engine Brand: SWEDIC, Condition: NEW, Engine Cooling Type: Radiator Cooled (std) , Engine Color: Yellow , Engine Condition: New , Turbo Type: None Mounted , Exhaust System: Dry , ECU Present?: no , Starter Voltage: 12 Volt , Injection Type: Mechanical Fuelpump , Generator KVA: 10.5 , Generator Hz: 50 , Generator Volts: 230/400 , Generator Amps: 13.5 , Generator Fases: 3 Fases , , https://www.hamofa.com/stock/generators/swedic-sw-11500-generator-10kv a-new/8, , = More information =, , Empty weight: 205 kg, Type number: SW-11500 GENERATOR 10KVA

Key data: 6400 mm, 1 mm

used Jorns double bending machine, with the following equipment: - 4 pneum. Clamping finger with short-part clamping finger - Attachment rail - Foot control - Sheet metal cassettes - Upper beam with rebate groove - Hydr. Material thickness adjustment - Clamp and angle stop (Matic) Machine is repaired, checked, cleaned by a specialist and is then fully functional. Test run is carried out. Working length 6400 mm Sheet thickness max. steel 1.5 mm Sheet thickness max. aluminium 2.0 mm Sheet thickness max. VA 1.0 mm Back gauge (min.) 15 mm Back gauge (max.) 1125 mm Colour anthracite/light grey Total power requirement 20 A Dimensions 7332 x 3721 x 2040 mm Weight 9250 kg Upper beam stroke (opening width) 200 mm Bending angle (max.) 145 degrees Crowning manual without roller scissors Number of stands 5 pieces Insertion depth 1150 mm Machine number K13036

Chopper Zeno Type: ZTLL 1150 x 1580 Year of Make: 1988 Rotor width 1150 mm Rotor diameter 380 mm Rotor speed 110 rpm. Hopper capacity approx. 5 m³ Capacity approx. 3 m³/h Hydraulic Moving Floor Both hydraulic cylinders for the moving floor were renewed in 2021. Motor 30 kW Weight approx. 3500 kg

OMEGON Freesbank LxWxH = +/- 1500x 1500 x 2350 mm Table = 1150 x 260 mm All employees speak Dutch, German and English. Prices are exclusive of VAT. Shipping is possible (at an additional cost). (Subject to changes and errors in technical data, information and prices as well as prior sale.)

General SKU079B444 MakeAviteq Vibrationstechnik TypeOA-1150/350-UVB No.6300095-001 Mounted on framecheck Specified Features - Vibro feeder Material finishPolished inside Main Features MaterialStainless steel Length1150 mm Width350 mm Vibro feeders MaterialStainless steel Vibro feeder(1x) Feeder width350mm Feeder length1150mm Feeder height275mm Closedcheck Inlet355x355mm With motor0,3 KW, 230/400 Volt (2x) Information LocationBarneveld Floorspace1,8x0,9 M Total height1,0 M Weight380 KGVibro feedersAviteqConveying systems > Vibro feedersBrand > Aviteq What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

Ball screw with nut, transroll spindle, ball screw nut, threaded spindle, threaded rod, threaded bolt, threaded rod, ball screw drive, linear bearing, -Rexroth: R15104D977/R15104D973 -Shaft: Ø 38 mm -Thread length: 1150 mm -Number: 2x spindles available -Price: complete -Dimensions: 1710/330/H250 mm -Weight: 54 kg

Clamping plate with T-slots, plate field, welding table, welding table, plate boring machine, T-slot plate, -T-slot plate: clamping plate with solid base frame -Length: 1350 mm -Width: 1150 mm -Plate thickness: 100 mm -Plate: with support ribs -Groove width: 26 mm -Groove spacing: 110 mm -Dimensions total: 1350/1150/H825 mm -Total weight: 1000 kg

Work platform, man basket, safety cage, scissor lift, aerial work platform, cherry picker, lifting platform, scissor lift, scissor work platform, work platform, aerial work platform, platform -Work platform: Ideal as an attachment to a telehandler, tractor, or other vehicle... -Manufacturer: GSL, work platform with extendable additional platform from aerial work platform -Platform load: max. 450 kg -Additional platform: Load extended max. 150 kg -Dimensions: retracted 3060/1150/H1300 mm -Transport dimensions: 3060/1150/H640 mm -Weight: 430 kg

Container, grit trap, storage container, transport storage container, storage tank, transport container, settling tank for groundwater lowering -Container: Transport storage container -Capacity: 4000 liters -Inner dimensions: 2990/990/H1000 mm -Connections: see photos -Dimensions total: 3570/1150/H1150 mm -Weight: 780 kg

Square broaching tool, multi-wedge broach, broaching tool, broaching needle, grooving tool, keyway broaching tool, keyway broaching needle -Manufacturer: HS Hasseay Savage, broach push broach -Type: 11518 18MM V -Keyway width: 18 mm -Quantity: 1 piece available -Dimensions box: 395/40/H40 mm -Weight: 1.3 kg

Manufacturer: Costa, Type: CCC + CCC 1150, Year: 1998, Monting of the machine: obenWalze/Walze/Walze , Equipment of machine 2: untenWalze/Walze/Walze, Double sided sanding line: yes, Sanding width mm: 1150, Sanding hight mm: 120, Number of sanding belts: 6, Sanding belt dimensions: 2620 X 1150, Table hight adjustment by engine: yes, Rubber roller: 3 +3, Shore roller 1: 70, Shore roller 2: 70, Walze 3 Shorehärte : 60, Längsschleifaggregate: ca.34, Belt 2 shoe unit: ca.22, Belt 2 synchronous and reverse run: ca.17, Belt 3 synchronous and reverse run: 34/22/17, Table hight adjustment by engine: yes, Combi unit roller/shoe: 8-20, Table hight adjustment by engine: ca 3 + 3, Abrasive belts at bottom: yes, Intermediate sanding of lacquer: yes, Programmanwahl extern: yes, Pressure pads for short workpieces: 150, Year :1998

The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 1 mm, 1 mm, 700 mm

5-Axis CNC Vertical Machining Center Mikron HPM 1150U Year of construction 2013 Heidenhain iTNC 530 NC Rotary Table Table Ø 1,000 mm Table load max. 1,100 kg Table rotation axis c-axis 360° / 0.001° NC swivel spindle Head swivel axis B-axis +16°/-120° / 0.001° X 1,000 mm Y 1,150 mm Z 700 mm Spindle speeds up to 24000 rpm. 238 tool magazine slots Two identical machines (MV-6519/MV-6520) available. The machines come from a former aerospace facility and are in good condition. They ran for about 8 years in continuous operation and 5 years sporadically. Offer number MV-6519 + MV-6520

General SKU321S564 LocationBarneveld CEcheck MakeSitecon Process Engineering Main Features Motor3 KW Length1150 mm Inlet diameter200 mm Specified Features - Horizontal screw conveyor MaterialStainless steel Horizontal conveyor screwcheck Trough-typecheck Diameter180mm Length1600mm Between inlet and outlet1150mm Shaft diameter90mm Pitch200mm Inletdia. 200mm Outletdia. 200mm Motor3 kW 230/400 Volt Screw speed106 rpm With covers(1x) Information TypeTrogförderschnecke Mach.No.910-080-00 Year of construction2009 Floorspace2,3x0,7 M Total height0,8 M Weight350 KgHorizontal screw conveyorsCatalysts & fillersFeed additivesPaper & otherSolventsDetergent & surf.Other pharmaceuticsCosmeticsOrganicsE-waste & metalFood additivesSugarLubricants & oleoDairyAnimal feedOther feedConfectionerySolid pharmaceuticsBeveragesDyes & pigmentsBiopharmaceuticalAPIPlastic & rubberMine ...

Pressure:200 t distance between columns:1910 mm stroke:600 mm distance table/ram, max. stroke up, adjustment up:800 mm table surface area:1900 x 1150 mm pressure of drawing cushion in table:80 t stroke of drawing cushion in table:300 mm die cushion area:1500 x 950 mm table height over floor:800 mm side window:1000 mm ram surface:1900 x 1100 mm return capacity:36 t speed down:400 mm/s speed up:170 mm/s working speed:30,5 mm/s oil volume:1500 l height over floor:4,85 m height beneath floor:2,6 m power requirement:45,0 kW weight:38,0 t dimensions (WxDxH):3,05 x 2,8 x 5,55 m German Safety: permitted for manual loading:UVV 11.064 - VBG 7n5.2 drawing cushion in table:hydraulic

Polar Mohr 115 E, Year: 2001, Pileturner PW-4-ABV, Elevator, ColorDisplay TFT 10.4 Monitor, Programmable with memory, Side air table, Unloader

Length 7 meters, extendable behind part 150cm total 850cm. Concerns trailer from 2017 is unused. Auction-ID: A1-42013-89

Auction-ID: A1-44832-696

Auction-ID: A1-44832-726

Auction-ID: A1-44832-665

Auction-ID: A1-44832-664

Auction-ID: A1-45188-250

Technical characteristics: Control type: FANUC Number of pins: 2 Chuck diameter: 2 x 165 mm Number of tools per turret: 2 x 10 Maximum speed: 3,500 rpm X/Z Fast Forward: 24 m/min X/Z axis travel: 190 / 170 mm

Holder for oil filter MWM 232 for sale Mann & Hummel Part Number: 6751283106 MWM Part Number: 2404242170

Tapping Machine PROGRESS MWB Model 71 1/2 to 2 inch 220 V 1.05 kw with sawing device ! with 2nd set of jaws and 2nd cutting head !' Dimensions: 950 x 500 x 1200 mm

Tapping Machine PROGRESS MWB Model 71 1/2 to 2 inch 220 V 1.05 kw with sawing device ! with 2nd set of jaws and 2nd cutting head !' Dimensions: 950 x 500 x 1200 mm

Combined Cycle CHP Power Plant 12.5 MWe + 1.6 MW Chilled Water This combined cycle CHP plant consists of one Dual Fuel Solar Turbine Mars 100 with 40 bar steam boiler, Siemens SST 060 Back Pressure Steam Turbine and one Double Acting LS Absorption Chiller with electrical, mechanical and control auxiliaries. Plant is maintained according to manufacturer’s instruction. Gas turbine engine was changed to Solar refurbished unit in June 2023 and it has accumulated only about 16000 hours since that. Both the gas turbine and the steam turbine were last overhauled by OEM service in mid-2025 and thus equipment is in good operational condition. This combined cycle CHP (trigeneration) plant delivers 10 MWe of primary electrical output from a Solar Turbines Mars 100 dual-fuel gas turbine, with an additional 2.5 MWe from a Siemens SST 060 back-pressure steam turbine and 1.6 MWth of chilled w ...