muller 800 t used for sale

Foot switch, safety foot switch, foot pedal, foot controller, foot remote control, pedal actuator -Manufacturer: L-TEC, Pedal actuator foot remote control type FC-4 -Connector plug: 5-pin -Overall dimensions: 300/155/H190 mm -Weight: 4.2 kg

BM-TEC Fat Baking Line Year of construction 2015 Stainless steel total 3 pieces High-voltage connection up to 200°C digital control / control unit Automatic feeder Electric Lifting + Lowering Height: 105cm Width: 390cm Depth: 10cm

Miwe rack oven Type: Roll-In e+ RI 1 0610-TXXL Year of construction: 2020, 2019, 2017 and 2016 with fuel oil burner (convertible to gas burner) Stainless steel cladding for 1x trolley 58×98cm with extractor hood and fan with drive-on ramp 400/230V 3/N/PE 50Hz very good condition Height: approx. 263cm Width: approx. 160cm Depth: approx. 160cm

Key data: 750 kN, 150 mm

Control: STE 328-89-1 1/2" complete TOX Powerhouse: S75.160.200.12D Table size: 996 x 695 mm Installation height: 600 mm Total stroke: 150 mm Power stroke: 10 mm Weight: 5700 kg Electrical connection 230 V

Electric motor, three-phase motor -Manufacturer: Verhagen, electric motor type 4P.T063D4 unused -Power: 0.37 kW -Speed: 1400 rpm -Shaft: Ø 11 x 20 mm -Construction: B14 -Protection class: IP 55 -Dimensions: 210/122/H155 mm -Weight: 5.0 kg

Tecnopool spiral cooler, model: TW650 Raffreddamento - type: TW 3 650 1491, 400 V, 3 Ph, 50 Hz, 60 A - north - south, plastic mesh belt - model: SX, number: 2PO400066 - tape width: 630 mm - product height: 100 mm - insertion height: 1000 mm - exit height: 4500 mm, 25 floors - 2 Alfa Laval evaporators - 3 fans each - model: ILBWH632GD - serial number: AA2257461 - year of production: 2011 - overall dimensions: 8400 mm x 5300 mm x 5300 mm - total length of the belt 422 m DISMANTLED

150 m pallet rack Jungheinrich type MPB Used goods very good condition, see pictures Height 3.9 m Depth 110 cm, blue Load 8.4 tons Beam length 2.7 m yellow Carrier with ballast /compartment 2400 kg Negotiation price: € 8.990,-- net from stock Offer consists of: + 52 pcs. frame pre-assembled, depth 110 cm, height 3.9 m +204 pcs. beam, length 2.8 m, 2400 kg ballast/compartment +408 pcs. Suspension locks +208 pcs Concrete Anchor Load plates, documents, etc. are a matter of course. Further accessories can be found in the accessories catalogue. Goods are in stock. Transport and assembly possible on request. Viewing possible at any time by appointment. Further information on request. Constantly over 5000 linear meters of pallet racking from numerous manufacturers. (Changes and errors in the technical data, information and prices as well as prior sale ...

32 Sulzer TW11 130” narrow single colour and MW Serial 45000 to 69000 18 machine MW 14 machine single colour Accessories Per Loom 6 Harness shafts 6 Frames 6 Cam Heald wire, and dropper as one machine 1 Beam 1 Cloth role 1 IRO Looms are running and in very good condition

electric motor, three-phase motor -Manufacturer: elsto, electric motor type AM-TK71BA2 -Power: 0.55 kW -Speed: 2640 rpm -Shaft: Ø 14 x 30 mm -Design: B3 -Protection class: IP 55 -Dimensions: 300/185/H145 mm -Weight: 8.3 kg

Electric motor, three-phase motor -Manufacturer: Verhagen, electric motor type 4P.T063D -Power: 0.37 kW -Speed: 1340 rpm -Shaft: Ø 11 x 17 mm -Construction: B14 -Protection class: IP 55 -Dimensions: 215/165/H130 mm -Weight: 4,8 kg

Geared motor, electric motor, electric geared motor -Manufacturer: Motovario gearbox type NMRV/030 -Speed: 91 rpm i 15.0 -Engine: Neri Motori type T56B4 -Power: 0.09 kW / 1360 rpm -Hollow shaft: Ø 14 x 60 mm -Protection rating: IP55 -Dimensions: 265/110/H155 mm -Weight: 4 kg

Twino Double Arm Dough Machine Advantages: less dough heating, gentle kneading process Tabletop Simple digital control Timer with 5 speeds and 10 kneading levels for 1.5 - 6 kg dough / 1 - 4 kg flour Water capacity 0.5 - 2 L Arm rotations 36 - 64 rpm Net weight machine 49 kg Motor power 750 W Connection: 230V 50Hz New machine 24 months warranty More TOP bakery machines in stock!

Double Arm Kneader Twino 12 Advantages: less dough heating, gentle kneading process Tabletop Simple digital control Timer with 5 speeds and 10 kneading levels Dishwasher safe for 3 - 12 kg dough / 2 - 8 kg flour Water capacity 1 - 4 L Arm rotations 36 - 65 rpm Net weight machine 88 kg Motor power 1500 W 230V 50Hz New machine with warranty More TOP bakery machines in stock!

Spiral Kneader Dough Machine Turri Model: ISFE 120 very robust technology! Mobile kneading machine with 2 brakes 2 LED timers, 2 gears, temperature display flour dust hood, Stainless Steel Boiler and Spiral for max. 120 kg of dough, Boiler left/right barrel Connection: 400V, 13.5 Amp., 32A-CEE plug Dimensions: 790 x 1300 x 1300 mm, WxDxH Used machine overhauled with 6 months warranty More TOP bakery machines in stock!

Simatic panel, operator panel, machine control, interface panel, control panel, operating unit, control panel, keyboard -Manufacturer: Witron, Teubner Metalwo Panel Display -Type: TAST21-IBS-S2-T2 -Number: 2x panel available -Price per piece -Dimension: 270/65/H220 mm -Weight: 1.8 kg/pc.

Machine reamers, reamer, reaming tool, locating knife cutting set -Manufacturer: Günther, Attachment reamer, machine reamer, Titex-Special -Socket: conical Ø 17-19 mm -Diameter: 37 mm -Dimensions: Ø 37 x 56 mm -Weight: 0.2 kg

Hydraulic unit, hydraulic pump, hydraulic pump, universal unit, gear pump, double hydraulic pump -Manufacturer: Orsta, double hydraulic pump -Pump 1: Type A 6.3 R -Pump 2: Type C 16-2 R -Motor: VEM KMR 112 M4 5.5 kW / 1440 rpm -Total dimensions: 725/250/H290 mm -Weight: 65 kg

vacuum furnace, chamber furnace -Vacuum furnace: with vacuum pump -Chamber size: D500/W400/H400 mm -Thermostat: up to max. 320°C -Vacuum pump: power 1.1 kW -Total dimensions: 890/800/H1785 mm -Weight: 180 kg -Control: Two-point control using program control

Electric motor, three-phase motor -Manufacturer: ATB, electric motor 80S 3327277-056 -Type: TAF 0.55/4-7 -Power: 0.185 KW -Speed: 1400 rpm -Shaft: Ø 20 x 60 mm -Type: B5 -Protection class: IP44 -Dimensions: 230/148/148mm -Weight: 8.1 kg

Tung-Yu Cold Forming Press 22” x 24” deep platens 12” daylight Pressure up to 35/40ton Year 2015 Overall dims: 1.2m deep x 1.8m x 2m high Weight: 2000kgs +/-

Control module, compact control unit, fan coil control, electronic module -Manufacturer: Meitav-tec, Universal Fan Coil Control -Type: MIGA1-FC-SUPER -Operating voltage: 230 volts -Cardboard dimensions: 170/90/H45 mm -Weight: 0.5 kg

Food extrusion product coating, drying and cooling line SCHAAF TECHNOLOGIE GMBH TYPE 318 COATING DRUM 1600 For the application of various taste and aroma giving materials by using various aromatising techniques. The special drum profile offers the following main advantages: - optimal Rolling of the product for uniform coating - minimum possible friction/damage of the product surface - no hidden corners, easy to clean, bacteriologically optimal surface. Adjustable drum speed, by frequency controlled AC gear motor 1.5 kW. Drum diameter: 1600 mm Drum length: 4000 mm Drum height: 3270 mm TYPE 284 DRUM DRIER/ROASTER 1600 PTFE Newly developed short and medium range infrared roaster for special thermal post treatment of expanded extrudate. The whole drum is coated with a low-wear PTFE layer. This ensures processing of extremely sticky coated extrudates. Unlike the conve ...

9 drawers Weight: 293 kg Dimensions LxWxH: 720x725x1000mm Included content: Listing see photo

1 fixed setting stick with roller quills 1 moving setting stick

Drilling diameter 3-25 mm in ELB Drilling depth in one stroke (mm) 810 with resetting 1,200 Tapping up to M20 – larger by milling Manual tool changer Spindle holder SK 40 altv. HSK 63 Drive power 5.5 kW / ED 100 Travel X (longitudinal) 1,050 mm Travel Y (vertical) 800 mm Table load up to 2,500kg Table size 1,000 x 1,500 mm CNC rotary table 0-360° manual

balancer, machine balancer, spring balancer, cable extension, weight compensator -Manufacturer: Fein, Balancer spring balancer -Load capacity: 1-3 kg -Number: 2x spring balancer available -Price: per piece -Dimensions: 260/200/135 mm -Dependent weight: 3 kg/piece

Gear motor, electric motor, electric gear motor, bevel gear motor -Manufacturer: Neri, gear motor -Gear: Speed: approx. 105 rpm -Engine: Type T63BN/4 -Power: 0.18 kW / 1400 rpm -Shaft: Ø 25 x 80 mm -Protection class: IP54 -Dimensions: 365/125/H165 mm -Weight: 8.1 kg.

Offer up to 2 UTX Techlon 200 round slings (polyester) here. WLL: 20000kg EWL: 5m Unfortunately, they have been dragged over the hall floor a few times and are now quite dark, but they are technically very well preserved, have no cracks or cuts and the blue shield is completely present. Last test 01/2021, no more use after 07/2021

Key data: 500 , 2840 , 4

TRADE Plane Model CM500

Radio system, antenna contact module, wireless RF modem, Modbus -Manufacturer: TRL, radio system wireless RF modem ovp -Type: IRIS RS485-EXT-02 -Number: 2x module available -Price per piece -Dimension: 135/65/H30 mm -Weight: 0.1 kg

Radio system, antenna contact component, wireless RF modem, pico cell antenna -Manufacturer: CP Technologies, Pico Cell Antenna 2.4 GHz Ovp -Type: WAN-2185 -Number: 2 antennas available -Price: per piece -Cardboard dimensions: 280/240/H85 mm -Weight: 0.7 kg

ELEKTRISCHER KASTENOFEN Verwendungszweck : Pulverhärtung Maximale Temperatur : 220ºC Das Heizsystem des Ofens ist als Zwangskonvektionssystem ausgelegt. Es basiert auf dem Prinzip, dass die Luft des Ofenvolumens mit Hilfe eines Umwälzgebläses in den Ofen gepumpt wird und die Ofentemperatur durch die Wärmeübertragung der Luft, die durch die Heizeinheit strömt, erhöht wird. Die Wände des Ofens und der Heizeinheit bestehen aus modularen Blechen und hochdichten Isolierplatten. Luftverteilungskanäle mit regulierbaren Klappen im Inneren des Ofens sorgen dafür, dass die Ofentemperatur an jedem Punkt gleichmäßig ist. Die Temperaturregelung ist digital und ermöglicht eine präzise Einstellung der Ofentemperatur. Die Heizeinheit wird seitlich, hinten oder oben am Ofen angebracht und besteht aus einer isolierten Heizkammer, einer Heizzelle mit Widerstand im Inneren, eine ...

12 galvanized conveyor belts, belt width 650 mm, capacity 150 to 200 t/h Lengths from 8 meters to 60 meters Left - clockwise rotation, with traction drive 037 KW Tel. 01715213204

CABLE POWDERING MACHINE FOR ELECTRICAL CABLES EXTERNAL DIMENSIONS Length : 1.000 mm Width : 1.000 mm Height : 2100 mm CABLE PASSAGE Size : 100 mm diameter Height from ground : 1.000 mm Cable insulation material : PVC, PE, XLPE to be used Cable size to be powdered: 5–70 mm diameter HIGH VOLTAGE UNIT Input voltage : 14V 16kHZ Output voltage : 100 kV Max. current : 120 µa Polarization : Negative TECHNICAL SPECIFICATIONS OF THE MACHINE Input : 220V 50 Hz Installed power : 1 KW Extraction fan : 3.000 m³/h 0,75KW Vibration : 0,15KW 220V Compressed air : 6-10 bar Air consumption : 300 lt/min Filtration : 320x300mm polyester filter Filter cleaning : Automatic Powder recycling : Vibration sieve Powdering method : Application by 2 electrodes, electro static application

Product number: 2830 Type: TRF630 Serial number: 6700597-9144-21 Year of construction: 2006 Compressed air: 6 Bar Water: 1.5 - 3 Bar Power: 3 x 400V, 50Hz, 15kW Dimensions: 1100 x 2050 x 1500 mm Weight: 635 kg

Automatic Groove and Grip Hole Eyelet Machine Hang Type 115-20 incl. Conveyor Belt and Ceiling Magazine Built in 1988 OKU-Automatic eyelet sorter, Conveyor belt Length 2,500, width 500 mm, Folding unit HANG, Benefit Investors Machine is in good condition

material width: 300 mm material thickness: 3 mm no. of straightening rolls: 7 weight of the machine ca.: 0,5 t dimensions of the machine ca.: BxTxH m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

1. LIQUID SPRAY BOOTH The spray booth is designed for ventilation and filtering of paint overspray during manual painting application. VENTILATION SYSTEM Side draft ventilation provides high efficiency during paint application. The filter wall is manufactured modularly from galvanized sheet metal panels and the extraction fan is placed on the upper part of the filter wall and choiceed with plastic propeller to prevent the risk of spark formation. The electric motor is placed outside the extraction duct and there is no direct contact of the motor with the polluted air. FILTRATION SYSTEM The extraction filter is on the back surface of the spray booth filter wall and is used in 2 stages with 99.9% efficiency. In order to increase filtration efficiency, cardboard filter and paint stopper fibreglass filter are used as 2 separate layers. The warning lamp on the control panel indicates th ...

PULVERBESCHICHTUNGSANLAGE, TRANSFER-TYP Aushärteofen - Gas, Diesel oder elektrische Quelle Pulverbeschichtungskabine - Zyklontyp oder mit Patronenfilter Pulverbeschichtungsanlage - manuelles oder automatisches System Hängefördersystem - Raupenfahrwerke und Rumpfform Wir bieten die besten technischen Lösungen und wettbewerbsfähige Preise Deutschsprachiger Ansprechpartner in Deutschland Kontaktieren Sie uns für weitere Informationen und Angebote VOGAMAKINA Ltd. abcs://vogamachine.com info@vogamakina

TRANSFER TYPE POWDER COATING LINE Curing oven - gas, diesel or electrical source Powder coating booth - cyclone type or cartridge filtered Powder coating equipment - manual or automatic system Overhead conveyor system - tracks trolleys and frull structure Contact us for quotation We provide the best technical solutions and competitive prices German speaking contact in Germany VOGAMAKINA Ltd.

Disc valve, flapper valve, ball valve, butterfly valve, gate valve, gate valve, diaphragm valve, diaphragm stop valve -Manufacturer: Sisto, gate valve diaphragm valve orig -Type: THM6-02 DN40 PN40 A105 H.64806 -Number: 2x valve available -Price per piece -Dimension: 285/140/H200 mm -Weight: 6.4 kg/pc.

1. ELECTRICAL BOX TYPE OVEN Purpose of use : Powder curing Maximum temperature : 220ºC The furnace heating system is designed as forced convection system. It is based on the principle of pumping the oven volume air into the oven with the help of a circulation fan and increasing the oven temperature with the heat transfer provided by the air passing through the heating unit. The walls of the furnace and heating unit are made of modular sheet metal and high density insulated panels. Air distribution ducts with regulated flaps inside the oven ensure that the oven temperature is homogenous at every point. The temperature control device is digital type and provides precise adjustment of the oven temperature. The heating unit is placed on the side, rear or top of the oven and consists of an insulated heating chamber, heating cell with resistance inside, circulation fan that can opera ...

Inductive sensor, electronic sensor, sensor cable, connection cable, connection cable -Manufacturer: Telemecanique, ready-made sensor cable orig -Type: XZC-P1164L10 -Order No.: 076312 -Number: 17x cables available -Price per piece -Dimensions packaging: Ø 210 x 40 mm -Weight: 0.5 kg/pc.

Inductive sensor, electronic sensor, sensor cable, connection cable, connection cable -Manufacturer: Telemecanique, ready-made sensor cable orig -Type: XZC-P1164L5 -Order No.: 076311 -Number: 10x cables available -Price per piece -Dimensions packaging: Ø 190 x 30 mm -Weight: 0.3 kg/pc.

Butcher Boy TCA32 Mincer Stainless mincer, on stand, 100mm diameter throat, with mincing plate, 3Ph

Make : Tetra Pak / FBF Model : 500 Capacity : 500 litres per hour stages : 2 Bar : 250 Location : Dairy Machinery UK Condition : Good

core boring: 70-560 mm bore depth: 20000 mm drilling diameter: 70-500 mm core boring capacity in St 60 - reboring: special: 560-1000 mm workpiece diameter: 3200 mm workpiece weight: 200 t faceplate diameter: 2900 mm speed of boring spindle:: 100 - 500 U/min feed range: 3 - 2000 mm/min boring spindle drive: 55 kW spindle head drive: 150 kW workpiece turning speeds: 230 U/min control: Fanuc total power requirement: - kW weight of the machine ca.: - t 2010 Retrofitted equipped with: - Fanuc Control - 4-Jaw Chuck - Oil Pressure Head - Boring Head - Drill Head - 2-Point Rollers Steady Rest (4) - 3 Point Steady Rest (2) - Bar Rest (2) - Coolant & Coolant Piping - Chip Conveyor - Honing Oil Tank & Honing Tool Bars The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roller chain, drive chain -per package: Length: 5 m -Size reinforced: 16B-1 1-way 1 x 17.02 -Quantity: 23 x pieces packages available -Price: per package -Package weight: 14 kg/piece

Balancer, machine balancer, spring balancer, cable extension, weight compensator -Manufacturer: KW, spring balancer type F2 with locking mechanism -Load: 98-176 N -Cable extension: 1.9 m -Quantity: 2x spring balance available Price: per piece -Dimensions: 225/125/H340 mm -Weight: 10.3 kg/pc.

800 x 600 470 mm 137 Piece(s)