mtu 12 v used for sale

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Single column - eccentric press PELS - RICHTER type PEKR 125Masch. No. 20684 Year of construction 1967Compressive force 125 ton. Projection 430 mmTable size 1100 x 750 mmPlunger area 890 x 650 mmTable opening 400 mmStroke adjustment 6 to 115 mmRam adjustment 100 mmInstallation height largest stroke top max. 450 mmClamping pin bore 50 mmStroke rate 60 strokes/min. Table height above floor 900 mmMotor power 7.5 kWNerg connection 380 volts, 50 Hz- overload protection by crushing plate in the plunger- compressed air

Internal threading machine Hagen & Goebel type HG 124Masch. No. 4112 Year of construction approx. 1980Cutting capacity in steel M3 to M10Cutting capacity in cast iron M3 to M15Cutting capacity in brass M3 to M17.5Throat depth 250 mmPine stroke 80 mmTable size 345 x 245 mmSpindle speed 200 - 1000 rpm. Motor power 0.55 / 1.0 kWNerg connection 380 volts, 50 Hz- 6 speed levels via belt change (3 steps via belt + 2 motor speeds)- thread pitch via guide cartridge- 2 pieces guide cartridges with 0.8 mm and 28 G

Eccentric punching machine HAULICK + ROOS type RVD 125Double column - Eccentric pressMasch. No. 212560 Year of construction 1981Compressive force 125 ton. Table size 880 x 800 mmTable opening 470 x 140 mmStand width 900 mmStand width laterally 415 mmRam stroke 45 mmRam adjustment range 0-80 mmInstallation height in the picture 340 mmStroke rate 50 to 300 strokes/min. Engine power main drive 22 kWNe-connection 380 Volt, 50 Hz- Double connecting rod engine with 4-bearing eccentric shaft for off-center tappet pressure

Clamping table with T-slotsClamping plate, clamping block, groove tableClamping cube for radial drilling machineClamping surface top: L x W = 1200 x 800 mmClamping surface side: L x H = 1200 x 200 mmOverall height: 400 mmD- Grooves: 20 mmD- Groove spacing: 200 / 60 mmOverall dimensions L x W x H: 1200 x 800 x 400 mmWeight: 680 kg; used

Electric chain hoist crane DEMAG type PM 12LF ManuliftElectric crane with one-handed operationFabr. No. 5877813 year of construction 1990Load capacity 125 kgHook travel 3.5 metersLifting speed 12 m/min. Fine lifting speed 2 m/min. Motor power 0.32 / 0.05 kWNeching connection 400 Volts, 50 Hz1 Load train = 125 kgManulift Hand control directly on the crane hookGood condition; used

A complete cutting line for sheet metal processing is available. 1) Decoiler Schleicher H-B4-1250, year of manufacture: 1983, power: 11kW, max. load capacity: 12500kg, strip thickness range: 0.5mm-1.25mm, max. strip width: 1100mm. 2) Straightening machine Schleicher RM 8-53/160, year of construction: 1980, power: 7.68kW, strip thickness range: 0.5mm-1.25mm, strip width range: 300mm-1000mm. 3) Trimming shears. 4) HSK HSKW/SF shears, year of manufacture: 1993, max. strip thickness: 1.5mm, max. material width: 1280mm. 5) Stacking line Schleicher, year of manufacture: 1980, max. load capacity: 1000kg, strip width range: 300mm-1000mm, strip thickness range: 0.5mm-1.25mm, feed length range: 200mm-1250mm, power: 1.5kW. On-site inspection is possible.

Machine name: Filter presses frame used Manufacturer: Passavant Type: 1200 x 1200 mm Year of Make: 1991 Design: Bridge spar press Filter pressure: 15 bar Press capacity: Possible approx. 2200 liters m2 Procedure: Closed Filter area: Possible approx. 160 m2 Plate format: For 1200 x 1200 mm Number of plates: Without plates but suitable 66 with 30mm cake thickness Plate Conveyor: Automatic Filter Cloth Washer: Yes Cake thickness: 30 possible Dimensions: L 6,700 x W 1,800 (2,400) x H 2,250 + 500 mm Curb weight: Approx. 14000 kg Tech. Documentation: Yes Note: Without plates but with 66 carriages for hanging the filter plates Accessories: A light barrier and a filter cloth washer Condition: Used Price: On request

Robot FANUC ARC Mate 120iC Année 2012 6 axes Charge utile : 3 KG Portée : 1811 mm Répétabilité : 0,08 mm Poids. : 250 kg

Completely new spark plugs from serie 6 of Jenbacher. Reference 1214569

Lift table HANDY type 1250E Table size: 700 x 700 mm Capacity: 250 KG Year of construction: 1998 Maxi lifting height: 1350 mm Voltage: 12 V Dimensions (L x W x H): 1400 x 600 x 1900 mm Weight: approx 250 KG

Lift table HANDY type 1250E - No 2 Table size: 700 x 700 mm Capacity: 250 KG Year of construction: 1998 Maxi lifting height: 1350 mm Voltage: 12 V Dimensions (L x W x H): 1400 x 600 x 1900 mm Weight: approx 250 KG

Cast iron marble plate on feet Length: 1200 mm Width: 1200 mm Height on feet: 780 mm Weight: approx 1,5 T

Two injection moulding machines Krauss Maffei are available. 1) Krauss Maffei KM 50 C1, year of manufacture: 1999, injection unit: SP220, screw diameter: 30mm, L/D ratio: 23, injection pressure: 2500bar, shot volume: 85cm³, machine dimensions X/Y/Z: approx. 3200mm/1350mm/1800mm, weight: approx. 2500kg, control: MC4, operating hours: approx. 86000h. 2) Krauss Maffei KM 125 C1, year of manufacture: 2000, injection unit: SP520, screw diameter: 45mm, L/D ratio: 20, injection pressure: 1878bar, shot volume: 217cm³, machine dimensions X/Y/Z: approx. 4500mm/1550mm/2200mm, weight: approx. 5500kg, control: MC4, operating hours: approx. 82000h. Documentation available. An on-site inspection is possible.

length: 1200 mm width: 800 mm table height: 880 mm Plate thickness: 60 mm weight of the machine ca.: 0,6 t dimensions of the machine ca.: 1,20,80,9 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

TDK GEN20-120-1P230, TDK-Lambda 19 Inch Laboratory Power Supply 44 mm package 0 - 20 V/DC / 0 - 120 A Clocked Input voltage range 85 - 265 V/AC Integrated RS-232 / RS-485 interface External, analogue programming and monitoring Type (general): Rack-mount Item condition: Used, in perfect condition R11B1_EK You can find more laboratory power supplies - new and used - in our shop! International shipping costs on request!

A vertical glass storage cabinet TMB with integrated lighting for inspecting glass sheets is available. Load capacity: 2000kg, machine dimensions X/Y/Z: approx. 6550mm/1250mm/3600mm, weight: approx. 1750kg. The lighting may need to be checked and possibly replaced. An on-site inspection is possible.

Kaeser CSD 122 SFC screw compressor built-in inverter 2.2-10.5m3/min, 75kW, 8.5bar Manufacturer: Kaeser Type: CSD 122 SFC Year of manufacture: 2006 Operating pressure: max 8.5bar Power: 75kW Capacity: 2.2 - 10.5 m3/min Operating hours: 96244 h (Last service: 88854 h) Inclusion dimensions: 1100 x 2200 x 1900 mm Net weight: 1600 kg

The scope of delivery includes: 01x Stand Protector, II. Choice (New) Manufacturer: SSI Schaefer Suitable for frame profile type: P213, P215, P217 Material colour: yellow Total height: 1,000 mm Total width: 130 mm Inner width: 122 mm Suitable for frame profile: 120 mm Total depth: approx. 65 mm Side size: 75 x 75 mm Material thickness: 4.00 mm Height deflector: 50 mm Drill hole diameter: 9 mm Drill hole spacing: 250|300 mm Weight | Pcs.: approx. 7.97 kg Number of holes: 08 pcs. Incl. mounting material consisting of: 08x Hexagon Bolt M8x30 mm 08x Hexagon Nut M8 16x washer M8 General information about the article: This item is only available for pickup. A more than desired transport or shipment of this item is additional costs, which are charged separately depending on the place of delivery. or scope of delivery can be queried from us.

Transnorm curved belt conveyor right bend 125°-775-600 IR600 RA2012 Technical details: Manufacturer: Transnorm Type: Belt Curve 125° right TS 1500-100 Curved belt conveyor Year of manufacture: 2001 Angle: 125° Running direction: right inner radius (IR): 600 mm belt width (GB): 600 mm Speed: please contact, motor not yet mounted Belt type: smooth, KT36 Drive location: outside pulling Condition: good condition / fully functional Scope of delivery: without supports & sideguide (please inquire if required) Optional: supports & sidequides Price plus VAT ex central warehouse Dr. Sonntag GmbH & Co. KG 97076 Würzburg Features: condition: good (used) Nominal / inner radius in mm: 600 Nominal / outside width in mm: 670 Belt width in mm: 600 angle: 109° Driven: YES Running direction: RIGHT Engine type: SEW Eurodrive Conveyor speed m / s: 1,0 scope of delivery: without supports and side  ...

Transnorm conveyor belt GF 12330-600-500 RA2072 Technical data: Conveyor length (NL): 12330 mm frame width (NB): 600 mm, 700 mm with motor belt width (GuB): 500 mm Overall height (BH): 80 mm, 430 mm with motor Supporting feet: optionally available Conveying speed (v m/s): 0,25 Drive: SEW gear motor R27 DT80N4 Electrical data: 50Hz V380-500, kW 0,75 S1 Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Frequency converter for stepless speed change Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: Construction year: 2001 condition: good (used) Conveying length in mm: 12330 Nominal / outside width in mm: 600 Belt width in mm: 500 Driven: YES Engine type: SEW Eurodrive Zentralantrieb mit Spannstation KW: 0,75/S1 Conveyor speed m / s: 0 ...

Transnorm belt conveyor GF 2200-1120-1000 RA2391 Technical data: Conveying length (NL): 2200 mm Framework width (NB): 1120 mm belt width (GuB): 1000 mm Framework width including Motor (MB): 1500 mm height (BH): 110 mm Side guides height: 400 mm Drive: SEW gear Motor with Movi-Mot Conveying speed m/s: freely adjustable between 0.4-1.3 m/s Electrical data: 50Hz V380-500, kW 1.1 Optionally available: Supports Prices net plus VAT. ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2018 condition: good (used) Conveying length in mm: 2000 Nominal / outside width in mm: 1250 Belt width in mm: 1100 Driven: YES Engine type: SEW Eurodrive KW: 1,1/S1 Conveyor speed m / s: 0,5-1,5 scope of delivery: including side guides without supports, including Movimot frequency converter For individual, professional advice, simply contact us. Simply contact us by phone ...

Transnorm belt curve conveyor left 30°-1270-1100-IR900 RA2303 Technical data: Frame width (NB): 1270 mm Frame width with Bearing cover: 1390 mm Frame width with Bearing cover and gearbox: 1480 mm belt width (GuB): 1100 mm height (BH): 250 mm height motor below: 300 mm height including motor (MH): 550 mm Inner radius (IR): 900 mm Conveying angle: 30° degrees middler conveying speed (v m/s): 1,0 m/s Drive: SEW motor motor with frequency converter Electrical data: 50Hz V380-500, kW 1,5 / S1 Belt: KT 96 new Year of construction: 2021 Height Sideguides: 194 mm Optionally available: Supports Prices net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2021 condition: new Nominal / inner radius in mm: 900 Nominal / outside width in mm: 1270 Belt width in mm: 1100 angle: 30° Driven: YES Running direction: LINKS Engine type: SEW Eurodrive K ...

Transnorm belt conveyor GF 4080-1310-1200 RA1862 Technical data: Conveying length (NL): 4080 mm Framework width (NB): 1310 mm belt width (GuB): 1200 mm height (BH): 120 mm Side guides height: 100 mm Drive: SEW Motor Electrical data: 50Hz V380-500, kW 0,55 Side guides on both sides: includet Optionally available: Supports Frequency Converter Prices net plus VAT. ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2018 condition: good (used) Conveying length in mm: 4080 Nominal / outside width in mm: 1310 Belt width in mm: 1200 Driven: YES Engine type: SEW Eurodrive KW: 0,55/S1 scope of delivery: including side guides without supports For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. W ...

The machine is in good technical condition, testing is possible by prior arrangement.

Offer 73066 Specifications: - Sanding belt dimensions approx. 2000 x 150 mm - Surface grinding opening approx. 560 x 150 mm - Sanding belt speed approx. 30 m/sec. - Contact washer B 150 / D 200 mm - Drive pulley B 150 / D 200 mm - Drive 400 V / 3 kW - Working height adjustable - separate mot. Dust extraction - Space requirement approx. W 750 x H 1050 x D 1500 mm - Space requirement para. approx. W 750 x H 1250 x D 750 mm - Weight approx. 180 kg

loading area: mit Untergestell weight: 125 kg length: 900 mm height: 350 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press brake with Stäubli robot cell press Manufacturer: LA G Model: GBS R 1250 50 The machine was only used for a very short period of time.

Gun: PH-3N, voltage: 400V, weight: 50kg. Supplied with operating manual, 2x ground cables with clamp BMS/BMK, gas connection, HZ-stud holder, adapter piece and key. An on-site inspection is possible.

Height=1.35 m, Overall length= 0.86 m, Overall width= 2.02 m, Net weight= 355 kg,

Height=1.27 m, Overall length= 0.98 m, Overall width= 0.7 m, Net weight= 170 kg,

Height=1.59 m, Overall length= 1 m, Overall width= 0.8 m, Net weight= 132 kg,

Height=1 m, Overall length= 1.2 m, Overall width= 1.3 m, Net weight= 83 kg,

Manufacturer: SPINNER Model: SERVO - LOAD 80 - 1200 Year of Manufacture: 2011 Voltage (U): 3/PE ~ 400 V Frequency (f): 50/60 Hz Input Current (Iᵍ): 5 A Fuse Rating (Iₙ): 10 A Find more here - / Contact us at -

Height=1.75 m, Overall length= 3 m, Overall width= 1.7 m, Net weight= 1050 kg,

pressure: 125 t chamfer lenght: 3050 mm distance between columns: 2550 mm ajustment speed: 90.0 mm/sec working feed: 10.0 mm/sec return speed: 75.0 mm/sec stroke: 140 mm dayligth: 375 mm column arm: 250 mm table width: 90.0 mm work height max.: ca. 950 mm Number of working hours: 14.100 h total power requirement: 13.5 kW weight: 8500 kg range L-W-H: 3630 x 2300 x 2505 mm From a maintenance workshop Good / well-maintained condition With only approx. 14.100 operating hours () Equipment: - CNC electro-hydraulic press brake - DELEM CNC control - model DA 58 Swiveling control panel, front left 2D graphic programming & product display Tool & program library - CNC-controlled axes: Y1+Y2 / X1+X2 / R1+R2 / Z1+Z2 / CNC crowning - CNC electro-motorized backgauge (X axes) Stop system with 2x CNC-controlled gantries - CNC electro-motorized height adjustment of the backgauge (R axes) - CNC ele ...

thread dia.: M5 - M24 turning speeds: 70 - 200 U/min working area: max. 1200 R angle adjustable from - to: 0 - 90 Grad voltage: 230 V engine output: 1200 W weight: 65,0 kg - with micro spray system for constant cooling & minimal Cooling lubricant consumption - Includes blow-out device to remove chips, ensuring optimal visibility on the borehole - Includes quick-change chuck for using taps for Through and blind holes - Swivel motor unit for thread cutting at any desired angle between 0° and 90° - Higher accuracy compared to manual thread cutting, thread is guaranteed right angle (90°) - high productivity, significant time savings compared to manual Threading - Quick-change chuck with integrated slip clutch prevents breaking of the tap - Includes large radius swivel arm for easy positioning tap on the workpiece - For thread cutting in steel, stainless steel, aluminum and non-ferrous met ...

thread dia.: M6 - M36 turning speeds: 30 - 150 U/min working area: max. 1200 R angle adjustable from - to: 0 - 90 Grad voltage: 230 V engine output: 1200 W weight: 65,0 kg - Includes quick-change chuck - for use with taps - for through holes and blind holes - Swivel motor unit for thread cutting - at any desired angle between 0° and 90° - Higher accuracy compared to manual thread cutting - Thread is guaranteed to be right-angled (90°) - High productivity - significant time savings compared to manual thread cutting - Quick-change chuck with integrated slip clutch - Includes swivel arm with large radius - for easy positioning of the tap on the workpiece - Highly economical due to low investment and maintenance costs - For thread cutting in steel, stainless steel, aluminum and non-ferrous metals Scope of delivery - Operation via touchscreen - Digital drilling depth display - Quick-change ...

bore capacity in steel (diameter): 50,0 mm arm length: 320 - 1.220 mm workpiece height max.: 330 - 1.170 mm turning speeds: 25 - 2000 U/min spindle taper MT: 5 MK base plate: 1300 x 980 mm threading: 42 M quill stroke: 335 mm total power requirement: 4,0 kW weight of the machine ca.: 3000 kg. range L-W-H: 2035 x 1000 x 2830 mm Furnishing: - Large-sized base plate, ideal for processing large workpieces - Thick-walled, polished column for increased sliding properties of the boom - Extension arm and drill head with independent hydraulic clamping - Simple height adjustment of the extension arm using a lifting motor - Ideal for drilling, countersinking, reaming and thread cutting - Hardened and ground gears, running in an oil bath - Good gliding ability of the drill head on the boom - sanded surface Scope of delivery: - Cube table - Drill chuck arbor MK 5 / B 16 - Reducing sleeves MK 5/4, MK  ...

pressure: 60.0 t chamfer lenght: 1270 mm distance between columns: 1000 mm column arm: 410 mm ram stroke speed: 160 mm/sec work speed: 10.0 mm/sec return speed: 165 mm/sec work stroke: 275 mm dayligth: 530 mm table height: 900 mm table width: 90.0 mm back stop - adjustable: max. 800 mm oil volume: 150 ltr. voltage: 400 V engine output: 7.5 kW Weight: 4320 kg range L-W-H: 2250 x 1960 x 2750 mm Demonstration/demo machine () From our showroom (like new) With very few operating hours -------------------------------------------------- CNC press brake with special equipment Version ERGO - knee room for the operator flexible articulated arm mount for the controller increased installation height increased cylinder stroke as well as increased bending beam speeds -------------------------------------------------- Furnishing: - DELEM CNC control model DA-66T graphic/touch screen 2D graphi ...

weight max. in kg: 1250 kg turning speeds: 2,0 U/min height: max. 1.120 mm Torque: Tisch 490 Nm weight: 685 kg The Siegmund Roto-Positioner is ideal for welding, Assembly and maintenance work. The positioning takes place via a hydraulic one Turn and tilt function. The Siegmund Roto-Positioner is also included equipped with a continuously height-adjustable axis. Furnishing: - Hydraulic rotation of the clamping plate - Tilt range up to 95 ° - Hydraulic height adjustment and tilt function - including hand control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 400 mm y-travel: 350 mm z-travel: 400 mm tool taper: SK 40 spindle turning speed range: 1,0 - 4.000 U/min feeds: 0 - 2000 mm/min quill stroke: 60,0 mm table-size: 650 x 350 mm T-slots: 14 H7 Control: TNC 124 engine output: 5,5 kW weight: 1800 kg dimensions of the machine ca.: 2000 x 1000 x 2100 mm New price ~ 55.000 euros () Furnishing : - Universal tool milling machine - HEIDENHAIN pattern control TNC 124 - The control panel can be swiveled to the right of the machine - hydraulic tool changer (DIN 69872) - Vertical milling head - SK 40 - X-axis feed .. 0 - 2000 mm / min - Y-axis feed .. 0 - 2000 mm / min - Feed Z-axis .. 0 - 2000 mm / min - Central lubrication, electrical - coolant device - Chip tray - Operating instructions for machine + control Special accessories included: - hydraulic machine vice - many tool holders - HEIDENHAIN HR 410 electronic handwheel The data for ...

pressure: 50.0 t chamfer lenght: 1275 mm distance between columns: 1040 mm column arm: 250 mm ram stroke speed: 225 mm/sec work speed: 0 - 9.8 mm/sec return speed: 160 mm/sec work stroke: 215 mm dayligth: 512 mm table height: 800 mm back stop - adjustable: 600 mm control: DELEM DM 51 operating pressure: max. 300 bar oil volume: 150 ltr. voltage: 400 V engine output: 6.0 kW Weight: 4300 kg range L-W-H: 1930 x 1510 x 2390 mm current new price approx. 80.000 euros special price on request good / well-maintained condition () - in checked condition - machine video - https://www.youtube.com/watch?v=5L8L2AYv0PU ------------------------------------------------------- PLACKE electro-hydraulic CNC press brake specially developed for the production of small parts The advantages: • Low energy consumption • High operating comfort • Wide range of applications • Fast, robust, low-noise • W ...