mixer 1500 used for sale

Thermal system, fan heaters, heating elements, radial heaters -Manufacturer: Karl Klein, fan with heater: HVL 150 -Fan: Type ENG 3-6 K/S30 -Power: 100 W / 7.8 m³/min -Heating attachment: Type 8.0104 1500 W -Inlet: Ø 170 mm -Outlet: Ø 55 mm -Quantity: 3x blowers available -Price per piece -Dimensions: 280/250/H270 mm -Weight: 6.2 kg/piece

Gear motor, electric motor, electric gear motor, stainless steel motor, stainless steel gear motor, stainless steel bevel gear motor, permanent magnet synchronous motor -Manufacturer: Bauer, adjustable stainless steel gear motor -Note: Frequency converter required -Type. SNFA5E09XA4-TF/VA-TM -Engine: speed 150-1500 rpm -Power: 1.1 kW -Hollow shaft: Ø 38 x 1750 mm -Protection class: IP65 -Dimensions: 645/200/H220 mm -Weight: 53 kg

Overhead crane, crane, electric hoist, manual trolley, trolley, crane trolley, crane trolley, crane trolley, trolley, girder trolley, monorail trolley, hoist -Manufacturer: Steel, crane chassis with electric cable winch -Cable pull: Type AS 2008-16 2/1 -Load capacity: 1500 kg -Roller spacing: 153 mm, dimensions see photos -Drum speed: 16.0 / 4.0 m/min -Main stroke/fine stroke: 8.0/2.0 m/min -Lifting height: approx. 9.0 m -Drive unit: FU-A 11 43 22 -Travel speed: 20.0/5.0 m/min -Transport dimensions: 1120/1020/H380 mm -Weight: 226 kg

Reluctance motor, electric motor, three-phase motor, electric gear motor, reluctance motor -Manufacturer: KSB, electric motor type 132S-BWA7F3NNWDWAZKS -Power: 7.5 kW -Speed 50 Hz: 1500 rpm -Speed 100 Hz: 3000 rpm -Design: B5 -Shaft: Ø 38 x 80 mm -Protection class: IP 55 -Number: 1x available -Price: per piece -Dimensions: 470/345/H300 mm -Weight: 56 kg

Operating pressure: 13 bar Refrigerant type: R410A - 2 Kg Auction-ID: A7-45347-661

First vertical machining center X-axis travel: 1,500 mm reach to 2000 mm Y-axis travel: 700 mm Z-axis travel: 600 - 700 mm Table dimensions: 1,700 x 700 mm Maximum Table Load: 1,200 - 1,500 kg Spindle Mount: BT-40 Total Machine Weight: approx. 9,000 - 10,000 kg Floor Dimensions (W x D): Approx. 4,200 x 3,000mm Maximum height: 2700mm Auction-ID: A7-44885-20

The industrial gas burner is designed for fire temperatures up to 1600 degrees Celsius and is infinitely regulated by a servo motor Transport dimensions: approx. 5100 mm long, 2800 mm wide, 3500 mm high Including: 1 x platform, 1x tipper, 1x steel table, 1 x ZPF Therm control cabinet and 1x hydraulic power unit. Auction-ID: A1-45447-3

- Operating conditions of this machine: unchecked. - Dimensions for transport approx. 1400 x 1200 x 2200 mm. - Approximated weight 300 kg. - This item is delivered loaded by truck. The costs of dismantling and loading are those that are specified as additional costs. Auction-ID: A7-44536-37

Revised in 2018 With piece counting table, up to 3 kg capacity. With floor platform, up to 1500 kg capacity, with digital display Weighing ground plane dimensions approx.: 1125 × 1500 mm useful Counting table dimensions: 270 × 290 mm Auction-ID: A7-45181-36

Featured; Air conditioning ; Radio; Heated seats. Various malfunctions visible on the Dashboard Auction-ID: A1-42013-206

Machine description of the Monforts, model KNC 5 1500 Machine description of the Monforts KNC 5 1500 Working range / Arbeitsbereich ▪ Distance between centers / Spitzenweite : 1500 mm ▪ Turning diameter over cross support / Umlaufdurchm. über Shelf Slits: Ø 290 mm ▪ Turning diameter over bed / Circlaufdurchmesser über Bett : Ø 500 mm ▪ Travel of the transverse carriage / Transporting distance of the Planschlittens : 265 mm ▪ Bed width / Bed width : 360 mm Spindle head / Spindle stock ▪ Spindle diameter in the front bearing / Spindle diameter. am progressing Bearing : Ø 100 mm ▪ Spindle mount / Spindle depth nach : DIN 55027 Size 8 ▪ Spindle drilling 71 mm ▪ Inner cone of the spindle metric 80 Hauptantrieb ▪ Stufenlos adjustable current flow system (100%/40% ED) 11/16.5 kW ▪ Gesamtdrehzahlbereich 2 – 2,800 min-1 ▪ Getriebestufe I 2 - 280 min-1 ▪ Getrieb ...

Lifting magnet, load capacity 1500Kg, see pictures. Condition: never used / new (5) Auction-ID: A7-45761-750

Lifting magnet, load capacity 1500Kg, see pictures. Condition: never used / new (5) Auction-ID: A7-45761-755

Equipped with spare rotor, hydraulically operated hopper valve, machine is V-belt driven (V-belts available), detachable hopper, Interchangeable basket. Auction-ID: A1-42370-21

equipped with machine running on external 400V or on integrated Perkins diesel engine with Crievemore generator, track undercarriage, track width 400 mm, radio remote control, vibrating feeder, 1500 mm throughput belt, cross discharge belt, rear discharge belt, Auction-ID: A1-42370-3

Construction hoist / passenger lift 7 persons lifting capacity 2000 Kg equipped with BS platform tow rope 50 meters including roof good working condition and complete Auction-ID: A1-40135-77

excluding tooling; including 4th axle; equipped with updated 2018 CNC control with touch screen and software Auction-ID: A1-45793-14

Transport - Case 117 x 58 x 70cm filled with 18 LTS SLT 15002 silver with safety's and rail mount Auction-ID: A1-45889-1643

4 Floodlights 1500W Outdoor suitable IP54 230 V Auction-ID: A1-45889-2684

Auction-ID: A1-45889-2876

CNC LATHE Inv. No. 13.113C1 Make PBR Model T30 SNC x 1500 Control SIEMENS 805T Year 1996 Centre Distance 1.500 mm Max. Swing over Bed Ø 600 mm Max. Swing over Cross Slide Ø 410 mm Max. Swing in Gap Ø 960 mm Spindle Bore Ø 105 mm R.P.M. 47 – 2.000 (in 2 ranges) kW 15/22 Volts 400 Cycles 50 Including: Automatic Turret, 8 positions Enclosed guarding Coolant Auction-ID: A1-45737-172

Control Type: Selogica Closing System: Hydraulic TECHNICAL DATA Closing Force: 1500 kN Clearance between Tie Bars: 470 mm x 470 mm Platelet Dimensions: 650 mm x 650 mm Mold Size: Min 250 mm Maximum Opening Stroke: 500 mm Maximum Distance Between Platens: 750 mm Screw Diameter: 45 mm Shot Volume / Shot Weight: 230 ccm / 210 grams PS Injection Pressure: 1670 bar GENERAL DATA Motor: 37 kW Heaters: 10.2 kW Operating Hours: To be verified EQUIPMENT Language: German Hydraulic core: x1 Air valve: Yes Service booklet: Yes Additional equipment: Robot access Auction-ID: A7-45917-3

48V/10Ah; unused; 5854 Auction-ID: A1-45901-716

Control Type: Selogica Closing System: Hydraulic TECHNICAL DATA Closing Force: 1500 kN Clearance between Tie Bars: 470 mm x 470 mm Platelet Dimensions: 650 mm x 650 mm Mold Size: Min 250 mm Maximum Opening Stroke: 500 mm Maximum Distance Between Platens: 750 mm Screw Diameter: 45 mm Shot Volume / Shot Weight: 230 ccm / 210 grams PS Injection Pressure: 1670 bar GENERAL DATA Motor: 37 kW Heaters: 10.2 kW Operating Hours: To be verified EQUIPMENT Language: German Hydraulic core: x1 Air valve: Yes Service booklet: Yes Additional equipment: Robot access Auction-ID: A7-45917-2

This lot consisting of full stock Modiform pots diameter 9cm 5 degree pot grey 1 palette 1x +-15000 pieces New Auction-ID: A3-43520-17316

Rühle Tumbler MKR 600, with vacuum, scraping arm, container size 600 liters, LED control, direct cooling by strong cooling unit, mixing and kneading, up to 25 rounds per minute, all stainless steel, with loading device, comfortable emptying of the goods by standard carriage size, refurbished. The machine is currently in the overhaul and can be tested in Koblenz, Germany.

Producer: Suhner Description: - Capacity- 2000l - Brand new microprocesor Mikster MCM 023 - Variable drum speed - Automatic control - Variable pressure level - Pressure measurement; 0-99 % - Manual work mode - 50 programs easy to change - 6 cycles to one program, max cycle time 100h, two phases on cycle - Total time one phase 99 minutes - Brand new inverter Lenze Section responsible for vacuum; - Vacuum pump Busch 36m3 /h - Vacuum valves Danfoss - Total power 5.5 KW ( main motor 4KW + pump 1,5 KW ) - Total weigth 1500 kg - Fully made of stainless steel

MTI P-10 laboratory mixer The laboratory mixer is suitable for mixing, homogenizing, dispersing and suspending of low-to high-viscosity products, heated, pressure and vacuum resistant Heating cooling jacket 5 bar Product space-1 / 0.75 bar Tank 15 l, Volume 11 litres. The machine includes two containers heated, presses a vacuum pump and a dispensing device to high-viscosity products from the mixing container. The documentation is available.

Are you looking for spare parts for your cone mixer? We have the most common spare parts suitable for various brands such as Nautamix, V-Mix, Vrieco mixeretc. in stock, or can produce them quickly and cost-effectively in our workshop. - Mixed screws - Replacement or replacement gearbox - Replacement or replacement of swivel arms - Gears, shafts, seals - Top bearings - Cross joints - Radial bearing - Outlets - Usw. We also have a repair and maintenance service. We would be happy to make you a non-binding offer. E-mail: t.roechter@heiligbv

You are looking for replacement parts for your cone mixer? We have the most common spare parts for various products such as E.g. Nautamix, v mix, Vrieco-mixer etc. in stock, or they can customize quickly and cost-effectively in our workshop. -Mixing augers -Spare or replacement transmission -Spare or replacement swing arms - gears, shafts, seals -Top bearings -Universal joints -Radial storage -Outlets -Etc. In addition, we have a repair and maintenance service. We like to submit a non-binding offer. E-mail: t.roechter@heiligbv

Ruhle MKR 220 high tech tumbler with cooling and vacuum.

Rühle Tumbler MKR 150, with vacuum, mixing- and scraping arm, container size 150 liters, adjustable Touch-PC control, direct cooling by strong cooling unit, mixing and kneading, up to 50 rounds per minute, all stainless steel, comfortable emptying of the goods by standard carriage size. You are very welcome to test the machine in our facility in Koblenz, Germany.

Vakona ESK 125 Tumbler, vacuum mixing and tumbling machine, the machine comes with tumbling arm and mixing arm, container size 125 liters, MC control, direct cooling by strong cooling unit, mixing and kneading, all stainless steel. You are very welcome to inspect and test the machine in our facility in Koblenz, Germany.

Height 2130 Width 1410 mm Length 2130 mm Weight 1500 kg Capacity 1200 l Voltage Electrical: 400V 50Hz 3N Installed Power 9.1 kw Main material Stainlees Steel Load 1000 kg Mixing System Spiral With Paddles Product discharge Pneumatic dampers, front Mixer type Vacuum Mixer Shafts amount Double Shaft

Ruhle Miknetum MGR 900, newest generation of Tumbler, with vacuum, mixing arm, container size 900 liters, filling size 675 Liters, intelligent touch-PC control, direct cooling by strong cooling unit, mixing and kneading , up to 25 rounds per minute, all stainless steel, loading device, comfortable emptying of the goods by standard carriage size You are very welcome to test the machine in our facility in Koblenz, Germany.

Wolfking” mixer-grinder Type TSMIG 1250/200 twin shaft paddle mixer mixer capacity 1.250 L. 200 mm – head with tool trolley all stainless steel dimensions mixer (l x w x h) : ± 2.350 x 2.000 x 2.600 mm loading height : 2.200mm pneumatic lid suitable for cooling with N2 or Co2

Anschlagmaschine 20 l, Fabr. Rego

Rühle Tumbler MKR 300, Ruehle Hightech Tumbler with vacuum, incl. mixing and tumbling arm, container size 300 liters, Touch-PC control, direct cooling by strong cooling unit, mixing and kneading, up to 25 rounds per minute, all stainless steel, with loading device. You are very welcome to inspect the machine at our facility in Koblenz, Germany. If you have any questions, please do not hesitate to contact us.

Blender Talsa MIX95P; 400 V, new, Bowl capacity 95 litres, engine completely in stainless steel, separate stirrer and Bowl drive, 1 speed, forward and return, Bowl tilt, Dimensions Lxwxh approx. 108x80x120cm, weight 170kg New machine, built in 2018

with mixing and Meng arm cooling vacuum

New machine - Contents: 1,000 litres when water is filled - Usable volume: approx. 800 litres depending on product characteristics - Maximum filling weight 1,000 kg - The mixer has a central bottom outlet - Containers, lids, swivel arm, mixing screw, V2A outlet housing

Foldable technical desk The ideal solution for lighting mixer, sound mixer or FOH Whenever it has to look good Several available Birch plywood, sanded and stained, desk can be folded flat and consists of one piece Auction-ID: A1-45889-30

Type: HM 200, high-performance mixer, partly in VA, Y:00, 1987, 6.5 / 9.5kW, 2 knife heads, control cabinet, completely on base frame, drives can be polum-switched.

Farrel Pomini model F620 Banbury internal mixer, net mixing chamber volume: 710 litres Machine number 6515. Original year of manufacture: 1972, but body replaced 1998 approx batch weight at SG 1 - 533kg, 4 wing rotors, drilled sides, fully stellite welded chamber, rotors and floating weight, S.S.A. dust seals, hydraulic drop door with linear actuator, pneumatic hopper, unidrive gearbox with 2 x CEM 1475kW, 1550A, 1000V, 800/1000rpm DC variable speed motors, Drive controls included, but operator controls not available. In good condition (only used for tyre compound masterbatch). Spares available: Door top (new), hinge shaft (new), 2 x dust seals, hopper seals and bearing seals.

Type: VGL 5000. Double-current mixer in standard steel version with 5,000 l. useful content, cylindrical mixing tank and conical bottom, with vertical middle screw, distribution arm and power line controller, rectangular connector for pocket filter, manhole, lower Screw bearing with air flushing, pneumatic flat slider at the outlet.

Farrel Pomini Model OOC Lab Banbury Internal Mixer machine number: 7511, Year: 1976 Net Volume: 4.24 Litres pneumatic hopper 30kW DC variable speed motor. Complete with control panel etc and in very good condition.

Thyssen Krupp model GK270NC Banbury type internal mixer, 4 wing tangential rotors, Year of manufacture: 2003 Latest Continental design chamber! Hydraulic hopper + power pack. Body and hopper only in good condition. Unidrive gearbox and motor can be quoted for if required (same centres as 11D or F270).

Material: stainless steel Engine: 7,5 kW Convey length: 2850 mm Convey width: 500 mm Very good condition. You can also get the entire system with all components.

1 x Farrel model F270 Banbury internal mixer, Machine number: 98M5023, Year 1999, 270 litre capacity, 2 wing rotor design, FYH type dust seals, Hydraulic drop door with linear actuator, Process oil system, Pneumatic hopper. with semi unidrive gearbox, AC variable speed motor, 550V (includes 11kv > 550v transformer). Alstom \Syncdrive\ AC variable speed drive controller, 1265 KVA, 550V, digital drive new in 2001. With Promtec Control system (complete but PLC missing). In feed conveyor and dust extraction system also available if required (at additional cost). Spare motor also available. Complete and in good condition (still installed at a factory in UK).