127,695 used machines on RESALE, but how to find them? Machine Search
I sell a tenon machine for parallel milling, grooves for pallet tape etc. WACO T2-SL Year of construction 1984. Groove width 30mm. Motor 3,3kW Made in Germany. Available the same. With dokumentazion.
Notching milling machine -automatic hydropneumatic milling feed -for milling cutters max.: Ø 250 mm
Table clamping surface: 300 x 1100 mm Travel x: 780 mm Travel y: 250 mm Travel z: 410 mm Cbgaxkvf39 Spindle holder: SK 40 Pinole stroke: 100 mm Spindle speeds: 31.5 - 1400 rpm Feeds longitudinally and transversely: 12.5 - 630 mm/min Feeds vertical: 6.3 - 315 mm/min electr. Connection: 380 V, 5.5 kW Space requirement: 1770 x 1500 x 2050 mm Weight: approx. 2200 kg
Counter holder, counter bearing, bearing block, pillow block, bearing for milling machine -Dovetail: 118 by 160 mm 32 mm high -Drawing with the photos -Number: 1x counter bearing available -Price: per piece -Dimensions: 340/95/H220 mm -Weight: 15.4 kg
Table milling machine, table milling machine -Spindle: comes from a Lubimez bench milling machine -Table milling machine: with rigid spindle -Dimensions: 800/800/H400 mm -Weight: 95 kg
Counter holder, counter bearing, bearing block, pillow block, bearing for milling machine -Swallowtail: 75 by 110 mm 25 mm high -Drawing with the photos -Dimensions: 215/70/H200 mm -Weight: 10 kg
Double end tenoner, edge processing machine, scoring motor, chipper motor, electric motor, spindle motor, milling motor -Power: 6.3 kW 5800 rpm at 100 Hz -Voltage: 380 V -Acquisition shaft: Ø 40 mm -Tool: mm -Dimensions: 540/260/H150 mm -Weight: 43 kg
ORDER NO. 6623 TECHNICAL DATA - diameter range of machined pins 200mm - min length of input material 1100mm - infinitely variable feed speed + front/rear - knife head drive motor 15kW - feed motor 1,7kW Successively: - 2 toothed pulling shafts - 4-knife head - 2 smooth pulling pin shafts - electrically adjustable knife head - electrically adjustable shafts - dimensions length / width / height 3570x1300x1700mm - weight about 4000kg ADVANTAGES – German production - the possibility of turning poles into a cone – used turner, very good condition Net price: 159900 PLN Net price: 35533 EUR depending on the price 4,50 EUR (Prices may fluctuate with higher fluctuations)
Control Siemens Sinumerik 828D Speed [rpm] 12000 Travel X/Y/Z [mm] 900/460/520 Tool pick-up BT40 General: Control system Sinumerik 828D X/Y/Z travel 900/460/520 mm Speed 12,000 rpm Tool holder BT40 Spindle: Belt spindle technology Speed 12,000 rpm Power 18 kW Torque 117 Nm Rapid traverse X/Y/Z 36/36/30 m/min Tool holder BT40 Tool magazine: Technology Chain Magazine (ATC TYPE) Number of stations 30 pieces Work table: Clamping area 1050 x 460 mm Table load 600kg Equipment / Accessories: Chip disposal chip conveyor Coolant supply IKZ plant Setup operation Electronic handwheel Miscellaneous Rinsing gun
Sales Description ------------------- This large CNC axis drive spindle originates from a high-precision gantry-type milling machine and has been fully refurbished, including complete replacement of all bearings. With a total length of approximately 367 cm and a robust construction designed for heavy-duty machining, it is ideal for machine builders, retrofit projects, and industrial users seeking a reliable, ready-to-install spindle unit. The spindle is stored in our warehouse in Bavaria, Germany, and is available for immediate delivery. Transport organization can done by IBA - the costs to be paid by the customer. Further detail information are provided in the attached datasheet as PDF-File. -------------------------------------------------------------------- Sales description This large CNC final drive spindle comes from a high-precision gantry milling machi ...
CNC machining centre HERMLE U 1000 T – universal milling machine For sale is a high-quality CNC universal machining center from the renowned manufacturer Hermle, model U 1000 T. The machine impresses with its stable design, high precision and versatile applications. Ideally suited for toolmaking, single part production and demanding milling work. General information: Machine Type: CNC Machining Center / Universal Milling Machine Manufacturer: Hermle Model: U 1000 T Year of Make: 1999 Control: Heidenhain TNC 426 Condition: Used, good general condition, functional Shipping time: Immediately available Technical data: Travel (X / Y / Z): approx. 1000 / 630 / 550 mm Table size: approx. 1200 × 630 mm Tool holder: SK 40 Spindle speed: up to approx. 7000 rpm Tool magazine: approx. 16 places Quill stroke: approx. 75 mm Milling head: swivel 0 – 90° (unive ...
Radial drilling machine used for drilling and milling Manufacturer: COLLET & ENGELHARD GmbH Type: BUV 1600 Year of construction: 1976 horizontally and vertically swivelling head Drilling capacity: 50 mm Travel arm: approx. 800 mm max column travel: 1000 mm Speed: 14 to 710 rpm Spindle stroke approx. 300 mm 380 V Dimensions: approx. 2600 x 1300 x 3000 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
used
Machine Details Warehouse number 1105-03692 Machine type Milling machine - Universal HERMLE brand Type fp 1000 Year of construction 1988 Control type CNC Control heidenhain 355 Storage location HAGUENAU Country of origin Germany Delivery time IMMEDIATELY Freight base EXW Technical details x-travel 700 mm y-travel 630 mm z-travel 500 mm Control heidenhain 355 Tool holder SK 40 (DIN 69871) Table clamping surface: 1000 x 490 mm Spindle speed gear stage 1 25 - 400 1/min. Spindle speed gear stage 2 401 - 1260 1/min. Spindle speed gear stage 3 1261 - 4200 1/min. Feed 5 m/min Rapid traverse 10 m/min Swivel of the milling head + / - 90 ° Pinole diameter 110 mm Pinole stroke 95 mm Total power requirement 18 kW Machine weight approx. 5 t Information with coolant device Sale without clamping devices
MAHO C Axis Machine Table - Table diameter: 600 mm Good condition fully functional can be visited and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article, in order to avoid misunderstandings, can be viewed before the purchase and tested under electricity. Please ask questions before buying to avoid ambiguity. For general questions or an appointment for a viewing, I can be reached at any time at the telephone number below or above. Errors in the description and prior sale excepted. VAT will be shown separately on my invoices. Shipping with freight forwarder.
CME FCM 9000 Bed milling machine 5-axis Table size 9500 x 1200 mm. Travel X-axis 9000 mm. Y-axis 1500 mm. Z-axis 1500 mm. Maximum table load 5000 kg/ Mtr. Vertical milling head can be swivelled by 1°x1° CNC control Heidenhain TNC 430 CB If you have any questions about the machine, as well as a scheduling for viewing, please contact us by phone or e-mail.
Equipped with Festo walk-through device Auction-ID: A1-45188-187
CNC-Universal milling machine MAHO MH700 C Table: 900 x 500 mm Travels: -X: 700 mm -Y: 500 mm -Z: 450 mm Spindle stroke: 100 mm Spindle taper: ISO 40 Spindle speed range: 20 - 3150 rpm Total power need: 40 kva Control: Maho / Philips CNC 432 Machine weight: 3,3 tn
Jig boring/Milling machine HAUSER 3DR Travel X: 400 mm Travel Y: 200 mm Travel Z: 400 mm Spindle: 2 speeds Cone:CM2 Spindle exit: 120 mm 2 speed ranges 60-1500 RPM / 1500-3000 RPM Table size: L 590 mm x W 320 mm Speed variator at the spindle 2 advances Auto descent: 0,03 mm/min - 0,06 mm/min X-axis functional with Mitutoyo devise Y and Z axis: defective scale Voltage: 380 V Width: 1500 mm Depth: 1700 mm Height in low position: 1800 mm Weight: approx 1,5 T
Emco F3 - Milling Machine - Vise - Workplace lighting - Coolant device - Tools & Machine Feet Technical data Working Range: - Slide path longitudinal: 300 mm - Slide path transverse: 200 mm - Vertical slide path: 350 mm - Quill stroke for vertical milling spindle: 45 mm - Vertical milling head swivel: ± 90 ° Clamping surface: - Table dimensions: 600 × 200 mm - 4 T-slots: 12 x 21 mm - Groove spacing: 45 mm Spindle: - Tool holder: DIN 2078 / SK30 - Tool clamping: Pull-out screw M12 - Spindle speeds: 80 / 160 / 245 / 360 / 490 / 720 / 1100 / 2200 rpm Automatic feed for longitudinal slides: - Feed force: 1600 N (160 kp) - Speed: 20 - 200 mm/min (infinitely variable) - Rapid traverse: 1200 mm/min Coolant Facility: - Tank capacity: 30 l - Flow rate: 15 l/min Three-phase motor: - Power: 1.1 / 1.4 kW (60% ED) - Speed: 1400 / 2800 rpm Dimensions: - Dimensio ...
Type: Univer FC 100 Power: 1.2 kW Power supply: 380 Volt Current consumption: 3 A Weight ca: 125 kg Directly from the customer used from November from CH-Pratteln available.
AVIA VMC 650 - Vertical Machining Center Recording: ISO 40 X/Y/Z: 650 / 540 / 620 mm The AVIA VMC 650 vertical machining center has been specially developed for the production of small to medium quantities. With a maximum workpiece weight of 700 kg, even heavier parts can be machined without any problems. The high rapid traverse speeds of 25 m/min in the X, Y and Z axes ensure high efficiency of the machine. With a spindle speed of 10000 rpm, a very good surface is guaranteed for a wide variety of materials. - Heidenhain iTNC 530 HSCI CNC control - Tool changer with 24 positions - Chip screw conveyor - Year of construction 2012 Technical data Table: - Table size: 800 x 540 mm - T-slots (size/spacing/number): 18 mm / 100 mm / 5 - Max. workpiece weight: 700 kg Spindle: - Type: Cartridge - Tool holder: ISO 40 according to PN-92/M-55085/01 (DIN 69871A) - Tightening ...
bore capacity in steel (diameter): 25 mm throat: 175 mm bore stroke: 50 mm : 16 mm spindle taper: ISO 30 spindle turning speed range: 50 - 3000 U/min : 380 mm : 175 mm table surface area: 700 x 180 mm connected load frequency: 230 V max. distance between table and spindle-nose: max. 320 mm total power requirement: 0,75 kW weight of the machine ca.: 150 Kg dimensions of the machine ca.: 670 x 550 x 910 m Drilling and milling machine with large table Digital display SINO 3-axis. Digital display quill stroke. 2 speed levels. Left/Right switch Pan head left/right 90° spindle protection. incl. tool box with various tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 30 mm throat: 200 mm bore stroke: 70 mm : 16 mm spindle taper: MK3 spindle turning speed range: 50 - 3000 U/min : 565 mm : 220 mm table surface area: 840 x 210 mm connected load frequency: 400 V max. distance between table and spindle-nose: max. 470 mm total power requirement: 1,1 kW weight of the machine ca.: 230 Kg dimensions of the machine ca.: 0,75 x 1,05 x 1,3 m Drilling and milling machine with large table Digital display SINO 3-axis. Digital display quill stroke. 2 speed levels. Left/Right switch Pan head left/right 90° Recording MC 3 - B16. Drill chuck 3 - 16 mm. spindle protection. Machine stand. incl. tool box with various tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
NC Rotary Table Brand FIBRO, type 11.13.6.15.5.11.11.4.0120 T2 Diameter 800 mm Height: 240mm The indicated retail price is net.
HOFLER HF 2000L hobber/gasher with both internal/external heads Year: 2013 Installed in 2020 Less that 200 working hours Table diameter: 1500mm Table loading: 18000kg Working stroke (external hobbing): 1760mm Working range above table (external hobbing): 150-1910mm Working range above table (internal hobbing): 250-1460mm Counter support-end face above table: 800-2300mm External toothing, Max: 2000mm Internal toothing, Max: 2400mm CNC control: Siemens 840D Complete weight: 61000kg Equipped with counter support
First commissioning: 2016 Control: Heidenhain iTNC 530 incl. handwheel HR 520 X-axis: approx. 2,500 mm Y-axis: approx. 3,000 mm Z-axis: approx. 1,250 mm A-axis: ± 110° C-axis: ± 300° Clamping table Clamping surface: approx. 2,500 x 3,250 x 400 mm 2-axis milling head VH30 Spindle power: 60 kW Spindle speed: max. 22,000 min-1 Torque: 95 Nm Tool holder: HSK 63A Tool tensioning: hydraulic Coolant supply: outside and inside Blowing air: Outdoor Drives Linear axes Feed speed X-, Y-, Z-axis: up to 60 m/min Axle acceleration X-, Y-, Z-axis: up to 5 m/s2 Connection data Connected load: 190 kVa Fuse: 315 A Dimensions, weights Space requirement machine with peripherals: approx. 10,000 x 9,000 x 5,650 mm Total weight: approx. 55,000 kg Colour Housing, portal, control cabinet: RAL 7035 light grey Milling head and applications: RAL 6038 luminous green ...
Important information on the auction and processing: Pick-up is only possible after prior written appointment. Only the item designated in the heading (only the machine) is for sale. Objects, attachments, tools, pallets, shelves or other materials visible in the photos are not part of the auction unless they are expressly mentioned in writing in the item description. All dimensions, weights, technical data and operating hours are approximate indications. No guarantee is given for correctness and completeness. Deviations are reserved. A forklift (1.6 t) is available by arrangement. There is no entitlement to free loading assistance, unless it is not time-consuming. In the event of extraordinary or disproportionate effort, we reserve the right to charge separately for any additional expenses incurred. The buyer is solely responsible for dismantling, loading and transporting. Mining is ...
Important information on the auction and processing: Pick-up is only possible after prior written appointment. Only the item designated in the heading (only the machine) is for sale. Objects, attachments, tools, pallets, shelves or other materials visible in the photos are not part of the auction unless they are expressly mentioned in writing in the item description. All dimensions, weights, technical data and operating hours are approximate indications. No guarantee is given for correctness and completeness. Deviations are reserved. A forklift (1.6 t) is available by arrangement. There is no entitlement to free loading assistance, unless it is not time-consuming. In the event of extraordinary or disproportionate effort, we reserve the right to charge separately for any additional expenses incurred. The buyer is solely responsible for dismantling, loading and transporting. Mining is ...
KORRADI UW 10 with Heidenhain equipment, details see pictures, immediately available
GeneralUniversal machining centre New DMG MORI Design; Control: CELOS with Siemens 840D sl Operate Technical DataFeed rate longitudinal/transverse/vertical50000/50000/50000 mm/minRapid traverse longitudinal/transverse/vertical50/50/50 m/minWorking area 1Longitudinal400 mmCross400 mmVertical375 mmTool changerType of magazineChain Type of gripperDouble gripper Number of tools60 Max. tool weight6 KgMax. tool length300 mmMax. tool diameter with occupied adjacent pockets80 mmMax. tool dia. with free neighbouring pockets130 mmFloor space/WeightDimensions (L x W x H)6,21 x 6,58 x 2,69 (6,21 x 7,38 x 2,69) mWeight approx.7200 KgPackage Mill / TurnPackage Mill / Turn NC-Mill-turn table 450x450 mm / 17.7x17.7 in rounded down to d460 mm / 18.1 in C-axis direct drive, speed max.1,200 rpm Integrated balancing system Motorspindle 20-20,000 rpm power 35/25 kW (40/100% ED) tool taper HSK-A63 according D ...
Milling machine MACMOM M 100, year of construction 1970. Without table. At call.
Graule AKF 6/250 - Year of construction 1999 - Engine brake - very good condition - technically tested and fully functional
maximum number of results exceeded
please refine your search
250 € 
