129,377 used machines on RESALE, but how to find them? Machine Search
Magnetic Drilling Machine, Magnetic Drilling MachineCore Hole Drilling Machine, Metal Core Hole Drilling MachineDR. BENDER Type EK 323Masch No. 180543 year of construction approx. 1988Drilling capacity 23 mmSpindle holder MK 2Spindle speed 160 / 400 / 1250 rpm. Magnet 215 x 105 mmDrilling unit 220 Volt, 50 Hz, 1025 WattE-Magnet 220 Volt, 50 Hz, 65 Watt- Spindle speed via 3 gear stages- Left and right rotation- E-magnet KOCH, type KL32/6- Drill head height adjustment guided in a linear guide- Manual expulsor- Drill stand on
Radial drilling machine WEBO type R4bRFabr. No. 15 / E195 Year of construction approx. 1965Drilling capacity 40 mmThroat: approx. 1250 mmSpindle holder: MK 4Spindle speed: 30 - 1325 rpm. 9 stepsFeed from 0.12 - 2 mm/rev. 9 steps; used
Column Drill ALZMETALL Type AB 4 SVMasch. No. 14805 Year of construction approx. 1980Drilling capacity 40 mmSpindle holder MK 4 - Short quillThroat projection 340 mmQuill stroke 180 mmTable size 710 x 560 mmColumn diameter 160 mmSpindle speed 30 - 765 rpm. infinitely variableMotor power 2.3 and 3.4 kW pole-switchableMains connection 380 volts, 50 Hz- Spindle speed over 2 motor speeds and infinitely variable gear- Gears with 2 gear stages for high torque at low speeds- Spindle on/off via
Column drilling machine GOTHABear power 30 mmSpindle holder MK 3 - long quill, throat depth 350 mmPine stroke 200 mmTable size 460 mmSpindle speed 160 - 750 rpm. 4 stepsFeed rate 0.1 - 0.2 - 0.3 mm/COLUMN diameter 160 mmMotor power 2.2 kWNerg connection 380 volts, 50 Hz- Spindle speed via 4 gear stages- Automatic feed- Rotatable drilling table with mechanical clamping- Table height adjustment via hand crank- Clamping surface at the machine foot 450 x 450 mmSpace required L x W x H 700
Column drill INFRATIREA - ORADEA type PH - 031Series. No. 02434 Year of construction 1975Drilling capacity 40 mmSpindle holder MK 4 - short quillThroat depth 320 mmQuill stroke 250 mmTable size 400 x 400 mmColumn diameter 160 mmSpindle speed 85 - 1500 rpm. 6 gear stagesMotor power 2.2 kWNet connection 400 volts, 50 Hz- Spindle speed via 6 gear stages- Clockwise and counterclockwise rotation- Automatic feed 0.10 - 0.16 - 0.25 - 0.4 mm/U- Drilling table swivelling- Table height adjustment via
Used Radial Drilling Machine DONAU Donauflex 145 Year of Make: 2006 Only a few hours of operation. • Drilling capacity in steel 45 mm • Boom travel 1,050 mm • Drilling radius min. 540 mm / max. 1,590 mm • Spindle speed 15 - 2,800 rpm • Tapping device • Tool holder MK 4 • Hydraulic clamping for boom and lifting column • Electromagnetic feed clutch • Machine light
IBARMIA double drilling machine model BP-50. Year of manufacture 2005. Serial number 043285. Equipped with two drilling heads for simultaneous operations. Pneumatic workpiece clamping system. Integrated cooling system (coolant). Motor power 4.2 kW. Working speeds 750 / 1500 rpm. Electrical connection 380 V / 50 Hz. Acoustic level 78 dB(A). Machine with CE marking. Ideal configuration for series production and repetitive operations. Robust industrial construction on common base. The dimensions are approximate. Auction-ID: A7-44864-2
Drilling machine, column drilling machine, pillar drilling machine, pillar drilling machine, multi-spindle head, multi-spindle drilling head, drilling gear -with two-spindle drilling head Manufacturer Sigloch Schrieder Type: V602 -Drive power: 1.02/0.88 kW -Drill distance adjustable: 18-110 mm -Max. Drill: 2x Ø 6 mm -Table size: 275 mm -Spindle mount: MK3 -Projection: 220 mm -Speeds: 100-2900 rpm -Columns: Ø 100 mm -Spindle stroke: 75 mm -Transmission -Dimensions: 900/400/H1910 mm -Weight: 230kg
KUHN HR 304 D + SITERA 330-20 E – Drill combination (new machine, YOC 2023) For sale is a new KUHN rotary harrow drill combination consisting of HR 304 D and SITERA 330-20 E. KUHN HR 304 D Power Harrow • Working width: approx. 3.00 m • Overall width: 3.12 m • Rigid frame, multiplex gearbox • PTO speed: 540 / 750 / 1000 rpm • 10 rotors, FAST FIT quick-change tines • Working depth: 3–25 cm (up to 31 cm with long tines) • Overload protection with tripping • Three-point hitch cat. 2 or 3 • Max. tractor power: 190 hp • Min. tractor power: 80 hp • Weight: approx. 1,035 kg • Attachment for seed drill KUHN SITERA 330-20 E seed drill • Year of construction: 2023 • Working width: 3.00 m • Transport width: 3.00 m • Number of rows: 20, row spacing: 15 cm • SEEDFLEX 1000 seed drill (double discs) • HELICA volumetric rotary dosing ...
Hilti TE 54 Hammer Hammer Impact Drill Chisel Hammer Combi Hammer Demolition Hammer Auction-ID: A7-45427-126
Würth HL 26-MLS Hammer Drill Impact Drill Combi Hammer Chisel Hammer Auction-ID: A7-45427-217
Hilti core drilling rig untested Auction-ID: A7-45427-139
Cordless hammer drills and cordless screwdrivers as a set in plastic box See pictures Condition: never used / new (5) Auction-ID: A1-45681-875
Electric sharpener, 230v, 50 hz, 14000 rpm Serial: PP70161DF Estimated weight: 8 kg Approximate dimensions: 600x400xh400 mm Auction-ID: A7-44996-152
Manufacturer Heckler & Koch Model AM 444 A Power consumption: 5.5 KW Voltage: 380/400 Volts Spindle holders for vertical and horizontal spindles: 40 Slide movement x = 410nn y = 350mm z = 400mm Vertical clamping table 850 x 255 mm Feed range 0-1500 mm/min Sliding gearbox 12-stage Speed: 63-2800 rpm Step jump 1.4 CNC control CNC 783/m Dimensions (HxWxD) 1.800x2.400x1.700mm Weight 1,500 kg Ref.Nr PLW18 Mistakes reserved!
Drilling capacity in steel: 32 mm Drilling capacity in cast: 40 mm Cutter head milling max.: 80 mm Projection: 220 mm Spindle speed: (12) 75-3200 RPM Spindle retainer: MK 4 Quill stroke: 125 mm Table size: 800 x 240 mm Travel (x / y): 555 / 225 mm Milling head swiveling: - 90 ° to + 90 ° Distance from spindle / table: 60-485 mm Head height: 425 mm T - slot size: 14 mm S1 motor power output 100%: 1,1 / 1,5 kW (400 V) Motor power S6 40%: 1.5 / 2.2 kW (400 V) Machine dimensions (W x D x H) : 1140 x 770 x 1500 mm Approximate weight: 287 kg without stand Features: Quick and easy change of speed using the gear selector switch Versatile application possibilities such as drilling, milling, thread cutting, … High running smoothness by polished, running in an oil bath gear gears Right - and the link run device for thread cutting Quill adjustment by means of ...
Standard ALB ear performance: 30 mm Thread cutting performance: M 20 (option) Thread: M 12 Spindle: MK 3 or SK 30 (option) Quill stroke: 100 mm Longitudinal / cross travel: 350/160 mm Distance spindle/cross table: 80 to 450 mm Table area: 600 x 240 mm Column diameter: 110 mm Total height: Max 1,920 mm Weight: 340 kg Motor pole shift bar: 0.8/1.5 kW Spindle speeds, continuous, selectable: 10 spindle speeds: 80-1,400 rpm 10 spindle speeds: 120-2,160 rpm 10 spindle speeds: 160-2,800 RPM Facilities: A versatile, accurate and handy drilling milling machine. The quiet-running drive and a perfect clamping of Quill guarantee good surfaces when milling. The headstock can be swung out. The stage is precise and precisely adjustable. Pitch 0.05 mm. clamping device for both axes. Full motor protection. Machine incl. Cabinet.
Special price for stock goods! Only while stocks last! Drilling-milling machine: Bernardo Type/Model: FM 45 HSV with digital display Condition: new Drilling capacity in steel: 32 mm Drilling capacity in cast iron: 40 mm Knife head milling cutter max.: 80 mm Projection: 220 mm Spindle speed: (12) 75 – 3200 rpm Spindle holder: MK 4 Pinole stroke: 120 mm Pinole feed: (3) 0.10 / 0.18 / 0.26 mm/U Table size: 800 x 240 mm Travel (x / y): 555 / 205 mm Milling head swivel: -60° to +60° Distance spindle / table: 60 – 485 mm Height adjustment milling head: 425 mm T-slot size: 14 mm Motor output power S1 100%: 1.1 / 1.5 kW (400 V) Motor input power S6 40%: 1.5 / 2.2 kW (400 V) Machine dimensions (W x D x H): 1140 x 770 x 1500 Weight approx.: 308 kg without base Characteristics: - High-torque 2-stage motor, speed range 75 - 3200 rpm - Double-sided swivelling m ...
Mikron WF31D Precision Milling and Drilling Machine Machine with chips and splash guard cabin Equipped with a Heidenhain TNC355 controller Technical Specification The WF 31 D is a precision milling and drilling machine for series production and CNC training. Driven by an automatically shifting step gearbox and Poly-V belts. Vertical spindle can be extended by 90 mm; Conversion from vertical to horizontal machining possible. Ball screws with DC drives allow simultaneous feed movements. Guides are protected against dust, chips and coolant. Specifications Manufacturer: Mikron Type WF31D Control: Heidenhain TNC 355 Longitudinal movement (X): 560 mm Transverse movement (Y): 500 mm Perpendicular movement (Z): 400 mm. Drive power: 3.3/4.0 kW Speed range: 40-4000 rpm Feed speed: 2-3000 mm/min Rapid traverse speed X/Y: 6000 mm/min, Z: 5000 mm/min. Electrical equip ...
bore capacity in steel (diameter): 16 mm throat: 170 mm bore stroke: 50 mm : 16 mm spindle taper: MK2 spindle turning speed range: 50 - 2250 U/min : 320 mm : 145 mm table surface area: 500 x 140 mm connected load frequency: 230 V total power requirement: 0,5 kW weight of the machine ca.: 90 Kg dimensions of the machine ca.: 0,5 x 0,45 x 0,84 m Drilling and milling machine with - variable spindle speed - Digital depth display - Left / right switch - Cross support - swiveling spindle head - Feeds via hand crank - Tool case with content but without digital display The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Radial drilling machine used for drilling and milling Manufacturer: COLLET & ENGELHARD GmbH Type: BUV 1600 Year of construction: 1976 horizontally and vertically swivelling head Drilling capacity: 50 mm Travel arm: approx. 800 mm max column travel: 1000 mm Speed: 14 to 710 rpm Spindle stroke approx. 300 mm 380 V Dimensions: approx. 2600 x 1300 x 3000 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
bore capacity in steel (diameter): 25 mm throat: 175 mm bore stroke: 50 mm : 16 mm spindle taper: ISO 30 spindle turning speed range: 50 - 3000 U/min : 380 mm : 175 mm table surface area: 700 x 180 mm connected load frequency: 230 V max. distance between table and spindle-nose: max. 320 mm total power requirement: 0,75 kW weight of the machine ca.: 150 Kg dimensions of the machine ca.: 670 x 550 x 910 m Drilling and milling machine with large table Digital display SINO 3-axis. Digital display quill stroke. 2 speed levels. Left/Right switch Pan head left/right 90° spindle protection. incl. tool box with various tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 30 mm throat: 200 mm bore stroke: 70 mm : 16 mm spindle taper: MK3 spindle turning speed range: 50 - 3000 U/min : 565 mm : 220 mm table surface area: 840 x 210 mm connected load frequency: 400 V max. distance between table and spindle-nose: max. 470 mm total power requirement: 1,1 kW weight of the machine ca.: 230 Kg dimensions of the machine ca.: 0,75 x 1,05 x 1,3 m Drilling and milling machine with large table Digital display SINO 3-axis. Digital display quill stroke. 2 speed levels. Left/Right switch Pan head left/right 90° Recording MC 3 - B16. Drill chuck 3 - 16 mm. spindle protection. Machine stand. incl. tool box with various tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
BALESTRINI TEAM automatic CUTTING , END MILLING and DRILLING MACHINE machine for joining parts of chairs, living rooms, furniture, etc. the TEAM machine is made up of 3 operating units: 1st unit: circular saw for cutting workpieces to length 2nd unit: spindle moulder for milling 3rd unit: drilling unit with multiple center distance head . there are 9 work programs that can be choiceed and they consist of the possible combinations of use of the 3 operating units. only 2 can be used , or 1 , or even the 3 operating units can work in different sequences . all units are operated by a hydraulic pump to obtain adjustable and smooth movements Technical data : - Cutting unit (circular saw) diam.mm.400. engine power Hp 3 - Moulding unit (spindle moulder) shaft diameter mm.30 . motor power Hp 5.5 max. tool dimensions mm.160, H=mm.120 - Boring unit . engine power Hp 3 . max. depth ...
x-travel: 3.000 mm y-travel: 2.500 mm z-travel: 2.475 mm w-axis: 800 mm rotary table: Juaristi MG-12 Rotary table surface: 2.000 x 2.500 mm T-slots: 11 T-slot - width: 170 mm table weight: 8.000 Kg table rotation: B- Achse – 0,001 ° Control: HEIDENHAIN i TNC-530 diameter of quill: 130 mm speed: 3.000 U/min tool taper: ISO 50 DIN 69871/1-B milling head: swivelling +/-: 2,5/2,5 Grad spindle drive: 30 kW transmission ratio: 2 speeds:: 0-2.500 U/min boring spindle: D`ANDREA UT5-800-S mm/min diameter: 800 mm cross travel: 250 mm Tools changer: 30 pos. Internal cooling system: 20 bar Chip coveyor: Inkl. handwheel: HEIDENHAIN HR-420 weight of the machine ca.: 45 t dimensions of the machine ca.: 9800 x 7320 x 5500 m -TS-3 head, TS-5 column and longitudinal bed INCLUDED: - Part touch probe RENISHAW RMP-60 - External coolant - 20 bar Internal coolan - protecting guards - mobile operator platfo ...
Ref. -No.: 10361 Manufacturer: SCHIESS Year of construction: 2023 Type of control: CNC Control: Siemens, Heidenhain, Fanuc - Configurable as required Storage location: Halberstadt Country of origin: Germany financing: nach Anfrage Support sleeve diameter: 130 mm X-Travel: 3000 mm Y-Travel: 2000 mm Z-Travel: 1600 mm Spindle stroke: 800 mm B-Axis: 360 ° W-Axis: 800 mm Spindle Taper: SK50 Max. Tool Weight: 25 kg Clamping Area: 1250 x 1250 (or configurable as required) mm T - groove width: 22 mm T - slot spacing: 160 mm Swivelling: Configurable as required ° Numbers Of Tools In Magazin: 40, 60, 120, 200, 240 Spindle Speed: 2900 RPM Max. Torque: 2500 Nm Drive Capacity - Spindle Motor: 41 kW
Type MX5116T+ V-380 Work table dimensions 1100x700 mm Sliding table 1085х250 mm Diameter of spindle 35 mm Spindle rotation speed 6000-8000-8000-10000 rpm Max. working thickness 120 mm Motor power 4 kW Dust exhaust outlets Ø90, 200x80 mm Number of wheels(pcs)-3 Wheels diameter-120 mm Wheels width-60 mm Feeding rate-3.5/5/7/10/12.5/16/25/32 m/min Motor power-750w/550w Machine frame - Cast aluminum Feeding direction:Forward/Reverse Transport dimensions 1650x700x1600mm Weight 466 kg Price 3060 Eur (EXW Jonava, Lithuania)
bore capacity in steel (diameter): 32 mm throat: 200 mm bore stroke: 70 mm : 16 mm spindle taper: MK3 spindle turning speed range: 50 - 3000 U/min : 220 mm : 425 mm table surface area: 700 x 210 mm connected load frequency: V max. distance between table and spindle-nose: 470 mm total power requirement: 1,5 kW weight of the machine ca.: 230 Kg dimensions of the machine ca.: 0,75 x 1,05 x 1,2 m Drilling and milling machine with - variable spindle speed - Digital depth display - Left / right switch - Cross support - swiveling spindle head - Feeds via hand crank - Tool case with content The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
20-75- CNC router WOODLAND MACHINERY (new) Type SX1325A-4 Useful working area axis X-Y-Z 2850-2100-150 mm Shaft, air cooled, 6kw+4.5kw x 3 18000 rpm. Engine Hybrid servo Control system LNC system Repeat positioning accuracy 0.03mm Work table vacuum plate Vacuum pump 11kw Maximum speed 50000 mm/min Maximum working speed 25000mm/min Resolution ±0.05 mm System resolution ±0.001 mm Code G Inverter 7.5 kw Voltage 380V/50HZ Transport dimensions 3200x2100x1800mm Weight 2100 kg The price is 23100 Eur
MIKRON Cutter Mod. VCP 1000 Machinable dimensions: square = 125x125 round 152 Machine visible in operation, in excellent condition.
for sale NEW - ALDURO Drilling-Milling Machine BFM 20V2 Drilling capacity up to 20 mm Spindle Holder MK 2 Head swivels +/- 90° Stepless speed adjustment 50 - 2250 rpm Cross table 500 x 180 mm Digital X-travel 195 mm Y-travel 140 mm Motor 1.1 kW, 230 V Machine without base (base), Can be purchased separately Weight approx. 113 kg further models and inquiries to FSA Maschinen AG
INFOTEC CNC machining center Model: 3121 3-axis Year of production: 2016 Dimensions of the machine working area for the axis X & Y: X: 2200mm Y: 3100mm Z-axis head travel: 250 mm Machine speed X, Y, Z: X: 60m/min Y:60m/min Z:12m/min Vacuum table
INFOTEC CNC machining center Model: 2515 5 axis Year of production: 2018 Dimensions of the working area of the machine for the X and Y axes: X 2100 mm Y 3100 mm Z-axis head stroke: 350 mm Machine Travel Speed X,Y.Z: X: 80m/min Y: 80m/min Z: 12m/min Vacuum table BECKER pump HITECO spindle with HSK 63F taper mounting
x-travel: 850 mm y-travel: 630 mm z-travel: 500 mm Control: Heidenhain : total power requirement: 16 kW dimensions of the machine ca.: 5 x 4,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Alzmetall AB 40 SV Price 9500,-€ Drilling capacity : 45mm Spindle : MK 4 Drilling capacity 45mm Spindle MK 4 Speed 65-1750 rpm Feed rate Yes 0.1 - 0.2 - 0.3 Drilling stroke 165mm Connection 50Hz 380V Motor 2.4KW Machine weight approx. 500kg
maximum number of results exceeded
please refine your search
4.000 € 
