mikron 400 u used for sale

Tie rod cylinders, hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Piston diameter: approx. 35 mm -Piston rod: Ø 32 mm -Stroke: 450 mm -Quantity: 1 piece available -Dimensions: 645/55/H70 mm -Weight: 6.7 kg

bore capacity in steel (diameter): 20 mm throat: 195 mm bore stroke: 80 mm boring spindle: MK 2 table surface area: 320 x 300 mm total power requirement: 0,75 kW weight of the machine ca.: 0,072 t dimensions of the machine ca.: 0,7 x 0,4 x 1,1 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Rear axle, steering axle, forklift axle, steering cylinder, hydraulic cylinder, support cylinder, hydraulic piston, pressure piston -Piston rod: Ø 55 mm -Condition: used -Stroke: 135 mm -Dimensions: 550/160/H120 mm -Weight: 20 kg

2 knife speeds 2 mixing speeds 2 separate bowl speeds emptier With loader Auto command 3000 K yoc 2017 only 1.603 running hours 125 kW total connected power

Key data: 1200 , 800

Clamping table in absoult as good as new condition! (Distort pictures, but table is straight!) The table comes from the area of a turbine assembly and is in top condition! Metrics: Width 1.200mm Depth 800mm Height 800mm Weight 700kg Number of T-slots 7 pieces T-slot table

technical details: - suitable for heavy starting machines - 18 l large tank = long running time - electronic voltage regulation (AVR) - Thermo-magnetic circuit breaker against overload and short circuit due to defective loads and cables - Insulation monitoring = safe personal protection - Oil deficiency shutdown - E-Start = high comfort Metrics: - Length: approx. 842 mm - Width/depth: approx. 523 mm - Height: approx. 557 mm - Weight: approx. 96 kg Drive: - Engine: Honda GX 390 - Power factor: 0.9 cos ɸ - Starter: E-Start / Hand Start - Type of fuel: Gasoline - Tank capacity: 18 l - Consumption at 75% load: 2.2 l/h - Sound pressure level Lp: 72dB(A) - Sound power level Lw: 97 dB(A) Generator: - Type: Synchronous - Rated voltage: 230 V - Apparent power at LTP: 7.2 kVA - Active power at LTP: 6.4 kW - Apparent power at COP: 6.0 kVA - Active power at COP: 5. ...

tube diameter: 50,8 mm wall strength: 1,0 mm square edge steel: 50 x 50 x 1 mm round bar steel: 25 x 6 mm weight of the machine ca.: 46 Kg dimensions: 0,6 x 0,4 x 0,5 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Morse taper sleeve, tool holder, Morse taper, Morse cone, taper sleeve, adapter -Adapter -Recording: MK6 -Tool holder: Ø 30 x 85 mm -Number: 1 recording available Price: per piece -Total length: 290 mm -Weight: 8.6 kg/piece

Labeler, make Krones, type: Universella 18-8-6. with 2 glue pumps, conveyors, sets for 0,25 lt + 0,33 lt Gastro crown cap, 0,33 lt Longneck screw cap, 0,5 lt NRW brown crown cap, 0,5 lt NRW white screw cap, 0,7 lt GDB screw cap, 0,75 lt Gastro screw cap, built 1998.

V-belt pulley, pulley -Recess: Ø 150 -Diameter: 310mm -Strap: 1 -V-belt width: 10 mm -Receptacle: Ø 60 mm -Weight: 17kg

Labeller, make Krones, type: Universella 600-15-8-6-130, 2 aggregates for cold glue label at body, shoulder, back; Videojet dating built 1995

Grinding wheel puller, cup wheel puller, double bench grinder puller, flat grinder puller, cylindrical grinder puller, puller head, dressing head for grinding machines -Support: 150 mm -Number: 1x disc puller available -Price: per piece -Dimensions: 192/94/H128 mm -Weight: 5.3 kg

Dividing head, dividing head, tool holder for grinding, drill grinding machine, milling cutter grinding machine, drill grinding holder, milling cutter holder -Accessories for: dividing head -with: hand crank -Dimensions: 390/400/H200 mm -Weight: 28 kg

Electric motor, three-phase motor -Power: 0.75 kW -Speed: 1370 rpm -Shaft: Ø 18 mm -Construction: B5 -Protection class: IP 44 -Dimensions: 340/201/H160 mm -Weight: 10.6 kg

Crimping jaws, crimping tools for cable end sleeves, wire end sleeves, cable lugs -for: cable end sleeves -Sizes: approx. Up to 28 mm² -in the suitcase -Dimensions: 490/300/H70 mm -Weight: 22.4 kg

Monitor with control panel, 2TT1001KAN03C, Unipo, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Consists of: - Monitor 2TT1001KAN03C, - Operator panel 7BXCTRLP000B, - bezel 7FPX0995X500, Function guarantee! For second hand parts, we can not provide conventional warranty and guarantee. However, we give you a functional guarantee. If the device does not work in the course of commissioning, you can return the goods and we will refund the purchase price.

Dear customers currently we offer you a used tape saw with sliding table of the brand HEMA. Here are the technical data of the machine: Roll diameter: 500 mm Cutting height: 500 mm Cutting width: 1,200 mm Blade length: 5770 mm Sliding table left half of the table: 1,150 mm right half of the table: 1,200 mm Table length: 3.150 mm Sliding travel: 3,150 mm Particularities: Machine is already dismantled! New leaf guides at the top and bottom! Price plus VAT, which will be shown separately on the invoice. Shipping possible for an extra charge! If you have any questions, please do not hesitate to contact us.

Dear customers currently we offer you a used tape saw of the brand HEMA. Here are the technical data of the machine: Table: 800 x 750 mm Cutting width: 680 mm Super cutting height: 480 mm Roll diameter: 700 mm Saw blade length: 5,000 - 5,150 mm Power: 3 kW Speed: 1,400 rpm Precision table swivel device with handwheel and rack Engine brake Dimensions: 1,290 x 800 x 2,300 mm Weight: approx. 580 Kg Price plus VAT, which will be shown separately on the invoice. Shipping possible for an extra charge! If you have any questions, please do not hesitate to contact us.

Edge grinding machine Work table swivel 45° Grinding height 150 mm Table dimensions 1440 x 710 mm 2 speeds for sanding belt 12/24 m/min 37qqrtber Height adjustment 130 mm from the unit

Machine vise, sturdy vise, drill vise -Jaw width: 164 mm -Back height: 45 mm -Clamping depth: max. 153 mm -Number: 1x vices available -Price: per piece -Dimensions: 530/200/H117 mm -Weight: 42 kg

Dear customers currently we offer you a used tape saw of the brand HEMA. Here are the technical data of the machine: Table: 1,275 x 895 mm Cutting width: 780 mm Super cutting height: 640 mm Roll diameter: 800 mm Saw blade length: 6,000 mm Power: 4 kW Speed: 1,650 rpm Precision table swivel device with handwheel and rack Engine brake Dimensions: 1,500 x 950 x 2,700 mm Weight: approx. 720 Kg Price plus VAT, which will be shown separately on the invoice. Shipping possible for an extra charge! If you have any questions, please do not hesitate to contact us.

pneumatic hydraulic machine vice, hydraulic vice, hydraulic vice, NC power clamp -pneumatic hydraulic: machine vice -Jaw width: 160 mm -Back height: 51 mm -Span width: max. 330 mm -Dimensions: 550/200/H125 mm -Weight: 47 kg

Dear customers currently we offer you a used tape saw of the brand HEMA. Here are the technical data of the machine: Table: 540 x 600 mm Cutting width: 380 mm Super cutting height: 300 mm Roll diameter: 400 mm Saw blade length: 3,320 mm Dimensions: 815 x 640 x 1,820 mm Weight: approx. 230 Kg Price plus VAT, which will be shown separately on the invoice. Shipping possible for an extra charge! If you have any questions, please do not hesitate to contact us.

pneumatic hydraulic machine vice, hydraulic vice, hydraulic vice, NC power clamp -hydraulics defective -Jaw width: 160 mm -Jaw height: 53 mm -Span width: max. 340 mm -Dimensions: 550/250/H135 mm -Weight: 55 kg

electric motor, three-phase motor -Power: 1.5 kW -Speed: 1400 rpm -Shaft: Ø 24 mm -double shaft output -Design: B3 -Protection rating: IP33 -Dimensions: 370/250/H190 mm -Weight: 16 kg

Dear customers currently we offer you a used tape saw of the brand HEMA. Here are the technical data of the machine: Cutting width: 865 mm Super cutting height: 700 mm Roll diameter: 900 mm Saw blade length: 6,550 mm Power: 5.5 kW with engine brake with CE incl. blade guide for particularly wide band saw blades! Dimensions: 1,630 x 1,080 x 2,825 mm Weight: approx. 950 Kg Price plus VAT, which will be shown separately on the invoice. Shipping possible for an extra charge! If you have any questions, please do not hesitate to contact us.

Hydraulic vice, machine vice, hydraulic vice, high pressure vice, hydraulic vice -Sale: as a spare part carrier -Jaw width: 160 mm -Back height: 50 mm -Span width: max. mm -Lower part: 1 -Dimensions: 330/550/H160 mm -Weight: 47 kg

Carel HeaterSteam UR020HL10S isothermal Steam Humidifier Carel HeaterSteam UR020HL10S is an isothermal steam humidifier. It produces steam by heating heating elements immersed in a steam cylinder filled with water. This can be normal tap water or completely demineralized water. The heat generated by the heating elements heats the water up to a temperature of 100 °C. Specifications: Dimensions: (L x W x H): 690 x 438 x 887 mm Weight: 63 kg Steam output: 20 kg/h Power: 15 kW Power supply: 400 V/3 Vapour pressure: 0...3600 Pa Steam connection: 40 mm Water supply connection: 3/4"G outside More items - new and used - can be found in our shop! International shipping costs on request!

Bezel, stick, lynette -Bottom parts: different sizes -Price: on request -Number: 4x bezel lower parts available -Price: per piece -Dimensions: -Weight: kg

Three-phase motor, electric motor -Power: 0.18 kW -Speed: 1390 rpm -Shaft: Ø 14 x 30 mm -Construction: B3 -Protection class: IP 44 -Number: 1x available -Price: per piece -Dimensions: 220/125/H165 mm -Weight: 4.3 kg

Pneumatic cylinder, standard cylinder, air cylinder, pneumatic stamp, air stamp -Stroke: 100 mm -Piston: Ø 80 mm -Piston rod: Ø 25 mm -Total length: 300 mm -Total length extended: 400 mm -Price: per piece -Number: 1x available -Dimensions: 95/95/H300 mm -Weight: 3.6 kg

Pneumatic cylinder, standard cylinder, air cylinder, pneumatic stamp, air stamp -Stroke: 105 mm -Piston diameter: 80 mm -Piston rod: 22 mm -Total length: 357 mm -Total length extended: 462 mm -Price: per piece -Number: 1x available -Dimensions: 96/96/H357 mm -Weight: 6.75 kg

Pneumatic cylinder, standard cylinder, air cylinder, pneumatic stamp, air stamp -Stroke: 200 mm -Piston diameter: 80 mm -Piston rod: 22 mm -Total length: 445 mm -Total length extended: 645 mm -Price: per piece -Number: 2x available -Dimensions: 96/96/H445 mm -Weight: 6.6 kg

Two-station machine for stacking canisters up to 10 ltr. Year of construction 2000. With PWDS and SFDR. Clamping force 200 kN. With aftercooling stations and needle bubbles. Also included is the conveyor belt for canisters. Good condition

Welding fume extraction table Welding table DCE UMA150HG5 dedusting Welding table with integrated suction with filter Manufacturer dust control equipment dust collectors Type UMA 150H G5 Rest according to photos

Pneumatic cylinder, standard cylinder, air cylinder, pneumatic stamp, air stamp -Stroke: 430 mm -Piston: Ø 80 mm -Piston rod: Ø 25 mm -Dimensions: 95/95/H683 mm -Weight: 1.35 kg

Frequency converter, frequency converter, drive converter, controller, variable speed drive -Type: Microdrive-3 UDZ-70 -Power: 33-44 kW -Connection: 380-480 V -20/+5% 48-62 Hz -A: 70 A -Dimensions: 440/145/H685 mm -Weight: 35 kg

Amplifier unit, amplifier -Type: DT110-U15-A-C2 -Series: multiNCDT -Dimensions: 65/170/H40 mm -Weight: 0.38 kg

WEINIG moulder model UNIMAT 17A with 8 shafts: -useful working measures 170x120mm -gimbal towing and pneumatic pressure -variable feed speed from 6.3 to 36.5 mt/min -Double wheel of upper feed before the 1st shaft -tandem feed groups in front of the 2nd and 4th shaft -fluted plane from 1st to 6th shaft -2000mm long entrance plane -manual lubrication pump of the table Tree layout: 1-under 2-right 3-left 4-right 5-above 6-under 7-above (free space below)    8-Universal

Flange bearing -Bore: Ø 20 mm -Mounting hole: Ø 12 mm -Bore distance: 64 mm -Dimensions: 130/130/H50 mm -Number: 16x available -Price: per piece -Weight each: 1.7 kg

Replacement blades for cutting machines -Knife size: 127x25.4x1.1mm -Urschel: 46097 -Number: 33x available -Price: per piece -Weight: 25 g/piece

WEINIG moulder model UNIMAT 17N with 8 shafts: -useful working measures 170x120mm -gimbal towing and pneumatic pressure -variable feed speed -top feed wheel before the 1st shaft -tandem feed groups in front of the 2nd and 4th shaft -2000mm long entrance plane -with SACOT automatic loader -manual lubrication pump of the table Tree layout: 1-under 2-right 3-left 4-right 5-above 6-under 7-above 8-Universal

Pneumatic cylinder, standard cylinder, air cylinder, pneumatic stamp, air stamp -Stroke: 200 mm -Piston diameter: 50 mm -piston rod: 16 mm (connection M16 x 1.5 thread) -Total length: 383 mm -Total length extended: 583 mm -Price: per piece -Number: 1x available -Weight: 1.35 kg

Pneumatic cylinders, air cylinders, pneumatic rams, air rams -Stroke: 80 mm -Piston diameter: 80 mm -Piston rod: 16 mm (connection M16 thread) -Total length: 260 mm -Total length extended: 340 mm -Price: per piece -Number: 1x available -Weight: 1.95 kg

electric motor -Power: 0.25 kW -Speed: 2800 rpm -Brake: 220 V -Shaft diameter: 14 mm -Design: B14 -Protection class: IP 44 -Dimensions: 275/140/H176 mm -Weight: 9 kg

Electric motor, three-phase motor -Power: 0.37 kW -Speed: 705 rpm -Shaft: Ø 14 mm -Flange: Ø 200 mm -Construction: B5 -Protection class: IP 54 -Dimensions: 265/200/H220 mm -Weight: 16 kg

Electric motor, three-phase motor -Power: 0.37 kW -Speed: 705 rpm -Shaft diameter: 24 mm -Construction: B5 -Protection class: IP 54 -Price: per piece -Number: 5x available -Dimensions: 290/170/H205 mm -Weight: 13 kg

Packaging machine Kallfass Universa 5050; good condition; cleaned and tested; Frame size 500x500mm; Passage height 100mm; with Tunnel Compact 650 S; Passage width 650mm; Passage height max.400mm; Cooling fans L-sealer Kallfass Universa 5050; good condition; cleaned and checked; frame size 500x500mm; product hight max.100mm; with tunnel Compact 650 S; working width 650mm; working hight max.400mm; cooling unit.

Electric motor, three-phase motor -Power: 1 kW -Speed: 2750 rpm -Shaft diameter: 15 mm -Construction: B5 -Protection class: IP 54 -Number: 1x motors available -Price: per piece -Dimensions: 215/120/H180 mm -Weight: 10.5 kg

Gear motor, electric motor -Speed: 8.5 rpm -Power: approx. 0.18 kW -Construction: B3 -Diameter shaft: Ø 40 mm -Protection class: -Dimensions: 565/255/H255 mm -Weight: 44 kg