mikron 400 u used for sale

faceplate diameter: 3500 mm turning diameter: 4000 mm centre distance: 16000 mm turning speeds: 0,71-33,5 U/min Rest: 2 tailstock quill taper MT: max. workpiece weight -without tailstock: 6300 kg max. workpiece weight between centres: 18000 kg Plate area: mm total power requirement: 31 kW weight of the machine ca.: 60 t dimensions of the machine ca.: 22x5x4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Cutting area at 90° Ø 135 --- flat W 250 x H 85 mm --- 4-carat 100 x 100 Miter: 22.5°L - 45°L - 90° - 45°R - 0°R HM circular saw blade Ø 400 mm Two-hand operation

Saw blade Ø: 360 mm Cutting range at 90° round: 110 mm Cutting area at 90° rectangle: 110 x 400 mm Cutting range mitred at 45° round: 110 mm Cutting area mitred at 45° rectangle: 110 x 280 mm Cutting speed: 16 - 50 m/min Drive motor: 380 V, approx. 1.5/2 kW Space requirement: 2600 x 1150 x 1600 mm Weight: approx. 1000 kg

max. wheel diameter: 400 mm gear width: 275 mm max. module: 6 Overall size: 300x330x245 cm weight of the machine ca.: 5,5 t dist. cutter spindle - workpiece spindle: 40/265 mm hob turning speeds: 50-400 U/min Specification: Max wheel diameter: 400 mm Min module: 1 Max module: 6 Table diameter: 370 mm Max wheel diameter: -With counterstay: 340 mm -Without counterstay: 400 mm Max axial offset: 275 mm Max tangential adjustment: 100 mm Tooth helical angle: 45 degrees Max cutter diameter: 145 mm Max hobbing length: 170 mm Hob turning speeds capacity: 63-180 U/min Feeds infinitely variable axial: 0,2-10 mm/U Feeds infinitely variable tangential: 0,1-5 mm/U Radial for spur gears: 0,1-4 mm/U Radial for worm gears: 0,025-1 mm/U Rapid traverse axial: 500 mm/min Rapid traverse tangential: 250 mm/min Radial for spur gears: 400 mm/U Radial for worm gears: 100 mm/U Motor power: 7.4 kW The data for t ...

diameter: 400 - 550 mm bore: 90 - 95 mm Various used face plates: Face plate 1 = 500 mm, short taper Din 55027 Gr. 8 = € 530.00 Face plate 2 = 550 mm, short taper Din 55027 Gr. 8 = € 530.00 Face plate 3 Röhm = 400 mm, short taper Din 55027 Gr. 6 = € 470.00 Face plate 4 = 315 mm, short taper Din 55027 Gr. 6 = € 260.00 Jaws can only be adjusted individually via threaded spindles. Machine dealer with own stock of 1600 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

SNA-10. 2 Emergency Power Systems - Complete System Manufacturer: Heinkel Aggregatebau GmbH Technical Data: - Heinkel SET HE500/396; 500 kW; 400 V; 722 A; 1500 rpm - IP 20, brushless synchronous machine AEG Rotaduct - 2 units Type DKBH4407/04; 3-phase AC; 280 kW; 400 V/404 A, 50Hz - 1500 rpm; 50Hz; cos φ 0.8; Built: 1991 - Diesel generator by MTU, Diesel tank: 1 unit, capacity: 1425 l - Starter battery; 2 units Hoppeke power HC 125300 - Dry cooler by Alfa Laval; 2 × 6 fans; 793.52 kW; each 50 m³/h - Ventilator: 90460 m³/h; Two-circuit cooler; Rooftop installation Find more here - / Contact us at -

Crushing system force: 120 t, Open box dimensions: 5000x2400 mm, Engine: Scania, Type: diesel, Year of construction: 2001

faceplate diameter: 3300 mm swing diameter: 4000 mm turning height: 3050 mm workpiece weight: 25 t faceplate turning speed range: 8 - 40 U/min ram swivable +/-: 30 ° main drive motor: 55 kW Control: Heidenhain TNC 640 total power requirement: ca. 85 kW weight of the machine ca.: 85 t dimensions of the machine ca.: 8,0 x 7,7 x 6,7 m Conversion and modernisation in 2024 equipped with: - CNC control Heidenhain TNC 640 & Handwheel - 2 swivelling ram supports (1x CNC controlled) - chip conveyor The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Halliburton HD 400 Pump Container . EX-container, VOLVO diesel engine D16. Diesel tank. Fan. Halliburton with 6" valve - can be replaced.

Offer 24228 Specifications: - Welding current 400 A 60% ED - 320 A 100% ED - Welding current adjustable from 20 A to 400 A - Current consumption 400 V / 46 A - with: - E. - Welding cable - Ground cable -Trunk - Space requirement approx. W 450 x H 750 x D 600 mm - Weight approx. 150 kg

Technical data: Type : Casting resin transformer Finish : Dry Make : ABB Year of construction : 2000 Condition : Used Rated power : 1250 KVA Medium voltage : 10 KV Low voltage : 400 V Groupset : Dyn 5 Frequency : 50 Hz Cooling Type :AN Gross vehicle weight : 3090 kg Nationwide delivery included.

Decoiler Coil weight: 4,5 ton Material width max.: 520 mm Coil exterior diameter: 1600 mm Expansion range: 460 - 530 mm Leveller / Straightener Material width : 20 - 400 mm Number of levelling rolls: 7 pcs. Diameter of the levelling rolls: 60 mm Number of pull out rolls: 4 pcs. Diameter of the pull out rolls: 60 mm Material thickness: 0,4 - 3,5 mm Feeding speed: 2 - 10 m / min Roll feeder Material width max.: 310 mm Material thickness: 3,0 mm Material thickness at max. width: 2,8 mm Material thickness at max. cross section: 850 sq mm Number of feeding rolls: 2 pcs. Diameter of feeder rolls : 80 mm Feeding speed: 104 m / min Required power: 1,5 kW

Capacity: 250 - 400 ton V ? Ring nominal force: 20 - 200 ton Counter ram nominal force: 10 - 100 ton Ram stroke: 30 - 200 mm V-Ring stroke: 40 mm Counter ram stroke: 40 mm Max. die size: 765 x 760 x 610 mm Number of strokes: 40 s.p.m. Approach speed: 120 mm / sec Return speed: 135 mm / sec Working speed: 5 - 50 mm / sec Die Weight total: 2400 kg

Inv. Num. : 8264 Type: MA-400HA Producer: OKUMA Created: 2008 Parameters: Work table length: 400 mm Work table width: 400 mm Maximum spindle speed: 8000 1/min X-axis travel: 560 mm Y-axis travel: 610 mm Z-axis travel: 625 mm

Manufacturer: Frenostat Bremsgerät Typ 2000 Hilger und Kern, Type: 400/60/3132000, Model: 137700,

Manufacturer: Klöckner Möller AMX Frequenzumrichter, Type: AMX3-460-16-400, FREE TEXT: ULN:460 F:50/60, Free text 1: UN: 460V , Free text 2: IN 16 Ampere,

Manufacturer: Doppelgehrungssäge, Type: DKG 400 A, Year: ca.1984, Control: Hand , Pneumatical clamping system: yes, Saw blade tiltable up to °: 45-90, Schnitthöhe min-max mm: ca. 70, Schnitttiefe min-max mm: 100, Schnittlänge min-max mm: 3500, Power saw engine kW: 3 KW,100 Hz, Width adjustment by engine: yes, Action controlled: yes, Saw blade diameter max mm: 300, rotations controlled: 4500, Bohreinheit Horizontal: 100, On customer order: inkl. Bohrstation, Year :ca.1984

Manufacturer: Doppelgehrungssäge, Type: DKG 400 A, Year: 1984, Control: Hand / Teilautomatik, Pneumatical clamping system: yes, Saw blade tiltable up to °: 45-90, Cutting hight max mm: ca. 70, Cutting lenght max mm: 2500, Power saw engine kW: 3, 100 Hz, Width adjustment manually: yes, Width adjustment by engine: yes, Action controlled: yes, Saw blade diameter max mm: 300, rotations controlled: 4500, Exhaust diameter mm: 100, inkl. Bohrstation, Year :1984

Manufacturer: Düspohl, Type: DGK 400, Year: 1980, Control: Hand, Pneumatical clamping system: yes, Saw blade tiltable up to °: 45 - 90, Cutting hight max mm: ca. 70, Max. cutting depth in mm: 150-2600, Max. cutting depth in mm: 150-2600, Power saw engine kW: 2,2, Width adjustment manually: yes, Saw blade diameter max mm: 300, rotations controlled: 5800, Exhaust diameter mm: 100, Year :1980

Manufacturer: Maskiner, Type: LPFK 2P 400 HKM, Year: 1997, Steuerung : Programm, Foil wrapping machine mm: yes, Foil stations: 2, Intermediate conveyor mm: yes, Shrinking tunnel mm: 300, Auslaufband mm: no, Electrical power shrinking tunnel kW: ca 30, Gesamtanschlusswert kW: 30, Foil 1 width mm: variable, Foil 2 width mm: variable, Through running hight mm: 150, Working width mm: 220, Year :1997

internal diameter: 800 mm grinding depth: 500 mm swing diameter: 850 mm total power requirement: kW weight of the machine ca.: 6,4 t dimensions of the machine ca.: m Used internal cylindrical grinding machine with face grinding device in special design with enlarged swing diameter and extended, hydraulic transverse movement Reconstructed and modernized 1995 in the Glauchau manufacturer’s plant, put into operation 1996 1. TECHNICAL DATA 1.1 Working area Grinding diameter in the workpiece guard internal grinding, min./max. mm 30/630(800) External grinding, max. mm 800 Grinding depth, up to approx. mm 500 Table stroke mm 800 Workpiece diameter, max. mm 800 Swing diameter in workpiece protection, max. mm 800 Without workpiece protection, approx. mm 850 Distance from workpiece spindle head to grinding spindle carrier, max. mm 1225 Adjustment of the internal grinding device on the table, max ...

NARGESA MC 400 3-roll bending machine was built in 2015 in Spain by PRADA NARGESA, S.L. The machine, designed for precision machining of steel components, is an excellent choice for the production of, among others, gates, fences, railings and balustrades. The extremely rigid body is distinguished by the use of guide shafts and 3-axis rollers made of hardened steel, whose drive eliminates slippage during the rolling process. This solution, combined with independent, manual adjustment of the lower axes, increases overall ergonomics and productivity. The NARGESA tube and profile bending machine weighs 365 kg. Technical specifications of the NARGESA MC 400 tube and profile bending machine - number of rollers: 3 - roller diameter: 130 mm - roller rotation speed: 8 rpm - number of shafts: 2 - shaft diameter: 40 mm - shaft usable length: 80 mm - power: 1.5 kW - power supply: 3x 400 V ...

Key data: 390 KW

Perkins 4008TESI-LC Containerised Natural Gas Cogeneration Plant. Hours: 0 Voltage: 400 V Scope of supply: Complete Cogeneration plant in container, gas heat exchanger, Control Panel WOODWARD EASY GEN 3000. Available for sale from Gas Engine Exchange . Please check our full range of equipment at gasengineexchange.com.

Nominal Power: 400 ton Stroke par minute: 16-48 Adjustable stroke: 10-250 mm Table dimension: 1200 x 1200 mm Ram dimension: 1200 x 1200 mm Distance table – slide: 1000 mm Adjustment slide : 200 mm Motovariator: 22-66 HP

REF-2391-B COMAS DRV 400 DOSING-DEPOSITING MACHINE WITH 5 NOZZLES Manufacturer: COMAS Model: DRV Type: 400 Serial no.: 3793 Year of manufacture: 2005 Dosing machine/depositor for the production of pastries Fitted with 5 standard conical nozzles (12 mm diameter) Voltage: 380V / 3-phase Working width: 400 mm Overall belt dimensions (mm): 2,200 x 530 (LxW) Overall machine dimensions (mm): 2,250 x 1,400 x 1,750 (LxWxH)

x-travel: 560 mm y-travel: 560 mm z-travel: 630 mm Control: MSX 701 III MAPPS Main spindle:: Max. rpm: 14.000 min/-1 power capacity - main spindel: 18,5 / 11 kW max. Torque: 120 Nm tool taper: MAS BT 40 distance spindle center to table: 80 - 640 mm distance Spindlenose and center of table: 100 - 730 mm pallet changer:: numbers of pallets: 2 size of pallet: 400 x 400 mm max. workpiece weight: 400 kg max. workpiecediameter: 630 mm max. workpiece height: 900 mm change time of pallets: 6,0 sec b - axis: 0,001 ° Tool-Presetter:: number of toolpositions: 60 pos. tool taper: MAS BT 40 max. tool diameter: 70 / (140) mm max. tool length: 400 mm max. tool weight: 8,0 kg feeds:: rapid traverse ( X / Y / Z ): 50 m/min feed speeds: 0 - 50.000 mm/min Tipp feed: 0 - 1.260 mm/min total power requirement: 35 kVA weight of the machine ca.: 9,8 t dimensions of the machine ca.: 5,5 x 3,5 x 2,8 m Docume ...

Wide-chamber pin mill with grey cast iron housing, output / throughput: 600 kg/h max. (depending on material), required motor power: 12 kW to 22 kW (optional). Rotor and stator disc in very good condition. Cleaned, anti-rust primed and repainted. Rust protection inside can be easily removed before commissioning.

Max pressure: 400 ton Table size: 1000 x 650 mm Between columns: 1000 mm Lower and upper table are heated Max temperature: 200° C Height: 2600 mm Weight: 9 ton Capacity: 400 ton

Key data: 400 KW, 500 kVA, 400 V

The largest model in Electroquell's range. The 500 kVA (400 kW) generator with a Ricardo motor is suitable for shopping malls, industrial plants and large investments. Ricardo Motor ComAp IL-NT AMF25 controller Brushless alternator Weatherproof housing Drip pan Possibility of continuous operation 24 hours a day Power: 500 kVA / 400 kW Voltage: 400 V Current: approx. 722 A Fuel: Diesel EN 590 Additional options: ATS system, remote communication, cooler for 55 degrees Warranty: up to 60 months

Behringer HBP 400 Depth of throat: 400 mm Max height of workpiece: 400 mm Length of band saw: 5800 x 38 x 1,3 mm Power needed: 5 kW Length : 2900 mm Depth : 2500 mm Height: 2100 mm Weight: 2,7 ton

Stainless Steel Continuous Mixer Manufacturer : MWM Type: 400 V-K Content: 400 litres Technical specifications : Machines No. 650 Continuous Mixer with Inclined Bucket Mixing Tool and Chopper Dimensions: length 3.00 m, height 1.00 m + 1.10 frame, width 1.30 m Engine: Power 15 kW, 1,460 /94 rpm Mixing shaft 94 rpm

Size: 980 x 600 mm Equipments: Investment table with tabulator 98 x 60 cm 4 head paper drills Speed regulation

Specifications will follow asap

Transnorm conveyor belt GF 2100-400-300 RA2405 Technical data: Make: Transnorm Model: TS 6565 motor-driven belt diverter D=65mm Conveyor length (NL): 2100 mm Frame width (NB): 400 mm, 600 mm with motor Belt width (GuB): 300 mm Overall height (BH): 200 mm Support feet: optionally available Conveyor speed (v m/s): 2.0 Drive: Nord Electrical data: 50Hz V380-500, kW 1.1 S1 Drive pulley: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Lateral guide on one and both sides Frequency inverter for stepless speed change Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Construction year: 2017 condition: Ausstellungsstück Conveying length in mm: 2100 Nominal / outside width in mm: 400 Belt width in mm: 300 Driven: YES Engine type: Nord KW: 1,1/S1 Conveyor speed m / s: 2 scope of delivery: without supports and side guides For indi ...

Labeller Manufacturer: HERMA Type H 400 V16R No. 9908984 E-No. 785097 Year of construction 2006

weight max.: 10 / 20 (einzeln / Satz) t workpiece diameter: Ø250 - Ø4600 mm gear diameter: 380 mm turning speed drive gear steples: 130 x 1300 mm/min total power requirement: 2x 0,75 kW weight of the machine ca.: 750 kg / 500 kg dimensions of the machine ca.: mm Steel rollers, dia. 380 mm Idle rollers with motor driven displacement of rollers Continously variable speed of drive rolls The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Qty. 1 Second-hand shredder Mfc.: METSO Denmark A/S Model: M&J Eta PreShred 4000S Built: 2013 Condition very good Working hours: 11,347 Power supply: Voltage 400 V AC, 50 Hz Main motor: 2 X 200 kW Rated current 760 A Main motor, full load current 2 x 341 Amp., PLC controller Drive principle, hydrostatic transmission with power consumption limiter. Working cutting cassette: 2 shafts Operating asynchronously Speed: 33 rpm Number of rotary knives: 2 x 12 pieces Number of lower, fixed knives 2 x 24 pieces Bearings 2 x 2 barrel

Pneumatic power chuck, Diameter 400 mm, Big Bore 140 mm 3 jaws, centrically clamped

Labeller Manufacturer: HERMA Type H 400 8 L Serial No. 20923342

Kersting belt conveyor Ejector Placer Separator GF 2880-510-400 RA2409 Technical data: Conveyor length (NL): 2880 mm frame width (NB): 510 mm belt width (GuB): 400 mm Overall height (BH): 780 mm intake and 640 mm output Supporting feet: includet Conveying speed (v m/s): with Frequency converter for stepless speed change Drive: Drum motor Electrical data: 50Hz V380-500, kW 0,55 S1 Drive drum: Ø = 100 mm Belt return roller: Ø = 100 mm parcele size: (max 550) x (390...420) x (max 200) LxWxH Controling and pneumatic included Optionally available: Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: Construction year: 2014 condition: good (used) Conveying length in mm: 2880 Nominal / outside width in mm: 510 Belt width in mm: 400 Driven: YES Engine type: Trommelmotor KW: 0,55/S1 Conveyor speed m / s: freely adj ...

DEMAG ERGOTECH VIVA 800-400 injection moulding machine was built in 2001 in Germany by Demag Kunstofftechnik (currently Sumitomo (SHI) Demag Plastics Machinery GmbH). This highly efficient machine is used for the economic production of plastic parts of different colours, shapes and sizes. These parts are produced using the reliable injection moulding method, which involves feeding plasticised plastic into a mould and then clamping it with high press force. The machine’s high-performance components, including a precision mould clamping system operating at a maximum force of 80 tonnes, ensure high repeatability of the manufactured products. The DEMAG injection moulding machine weighs 3750 kg. Technical specifications of the DEMAG ERGOTECH VIVA 800-400 injection moulding machine - maximum mould clamping force: 80 t (800 kN) - screw diameter: 35 mm - maximum injection weight PS: 157  ...

Key data: 270 mm, 470 mm, 270 mm

Turning length: 470 mm Turning diameter over bed: 270 mm Turning diameter over cross slide: 145 mm Spindle speeds: 56 - 4000 rpm Spindle Passage: 26 mm Digital Readout: On X and Y Axes Country of origin: Netherlands Engine power: 1.75 hp Machine weight: 900 kg Machine LxWxH: 1200 x 460 x 1200 mm

AUTOMATIC EDGE BANDER machine model STEFANI MONOBETA 4000 second hand machine with Instruction Booklets for the application of edges in PVC, veneer, melamine, ABS , thin solid wood strips for furniture, furnishings, kitchens, bathrooms, doors, panels and various XILIA positioner system technical data : tiltable gluing group: 0° / 7° min. height of gluing panel mm.10 max. height of gluing panel mm.60 min. thickness roll edge mm.0.4 max. thickness roll edge mm.3 max. thickness wood edge mm.25 min. panel width mm.60 min. panel length mm.110 adjustable feed speed: from 8 to 22 mt./min. electric press lift telescopic support for large panels soundproof cabin composition : 1. gluing group with glue tank 2. pressure rollers 3. edge feeder 4. end-cutting unit for front and rear vertical cutting of the excess edge - n.2 motors 0,44 Kw at 12000 rpm 5. trimming unit ...

Key data: 4000 mm, 2000 mm, 575 mm

Pair of cast iron angle plates Drilling diameter: Ø 27 mm Width: 575 mm Depth: 2000 mm Total height: 4000 mm Unit weight: approx 6 T

Key data: 2500 kN, 40 mm

Manufacturer: ARBURG Type: Allrounder 630 H 2500-400 Control: Selogica Year of Make: 2019 Technical data closing page Clamping force: 2500 kN Wooden dimensions h x v: 630 x 630 mm Panel size h x v: 900 x 900 mm Min. installation height: 300 mm Max. installation height: 750 mm Plate spacing max.: 1300 mm Opening travel: 550 mm Ejector stroke: 225 mm Ejector force: 86 kN Centering of movable plate D: 160 mm Centering fixed plate D: 160 mm Technical Data Spray Side Screw diameter: 40 mm Displacement: 201 cc Spray pressure: 2000 bar Worm torque: 550 N Outdoor injection flow: 251 g/s hp Dimensions & Weight Machine dimensions LxWxH: 7.05m x 2.05m x 2.35m Total Weight: 13050KG Equipment Screen text German CEE socket 16A Machine including handling Machine with water battery Machine without material hopper Machine without protective enclosure Levelling elem ...

Lg.Nr. 24029 Specifications: - Saw blade diameter up to 400 mm - Cutting range at 90° around 130 mm - Square 120 mm - Rectangle 300 x 40 mm - or 240 x 85 mm - at 45° around 130 mm - Square 110 mm - Rectangle 245 x 40 mm - Mitre adjustable Li + Re each 0 - 90 ° - 2 cutting speeds 13 + 26 m/min - Drive 400 V / 1.2 / 1.8 kW - Feed speed of the saw blade hydr. Infinitely variable - Coolant device - Material replenishment machine - Space requirement approx. W 2400 x H 1850 x D 1100 mm - Weight approx. 1250 kg

Step conveyors, step lift conveyors KÖBERLEIN & SEIGERT Type A 400 / 2000Feeding technology, feeding system, incline conveyors, inclined conveyors, steep conveyorsFabr. No.03-3964 Year of construction 2003Slide width 400 mmSlide thickness 40 mmConveyor stages 10 piecesTransfer height on the incline conveyor 2200 mmTransfer height on the side of the feeder 1800 mmFilling height 750 mmConveying slope 75Motor power 1.5 kWMotor speed 1450 rpm. Mains connection 400 volts, 50 Hz- Low-wear sliders- Electromechanical drive-

Vibratory Spiral Conveyor / Sorting Device / Spiral Conveyor / Vibratory Conveyor RNA Shaking Bowl, Sorting Device / Screw Feeder with Vibratory Conveyor for Screwing TechnologyFeeding System, Feeding DeviceManufacturer: RNA Rhein-Nadel Automation GmbHTyp: SRC-N 250-2LSer.- No: 03611 Year of Construction: approx. 2000Pot Diameter Bottom: 300 mmPot Diameter Top: 350 mmPot Inner Height: approx. 25 mmSorting Track Width: approx. 30 mmTotal Height (Drive + Pot with Sorting Path): 380 mmOscillation Frequency: 100 Hz / 6000 min-1Power supply: 230 volts, 50 Hz- The

Center height: 195mm, center width: 1250mm, turning diameter over bed/faceplate/in bed gap area: 400mm/245mm/585mm, spindle bore: 54mm, speed: 2500rpm, power: 7.5kW, rapid traverse face pull/longitudinal pull: 1.5m/3m/min, quill: MK5. Machine dimensions X/Y/Z: approx. 2600mm/1500mm/1600mm, weight: approx. 1800kg, control: GE Fanuc. Documentation available. On-site inspection is possible.

Saw blade diameter: 2x400mm, max. cutting length: 4000mm, cutting angle: +/-45°. Documentation available. On-site inspection is possible.