mikron 400 u used for sale

BERNARDO Variomill FU 2000E Servo universal milling machine was built in 2020 in Austria by PWA Handelsgesellschaft m.b.H. The machine, distinguished by its stable design made of grey cast iron and the use of modern technologies, is the perfect choice for machining heavy, oversized workpieces. All linear axes are driven by high-performance servo motors, which guarantee appropriate accelerations and feed rates in each direction. What’s more, the X axis has been coated with a special Turcite B coating to reduce the effect of slippage. All of this, combined with extensive equipment, maximises the precision and repeatability of the produced parts, even during the most intense challenges. The Variomill FU 2000E Servo vertical milling machine weighs 4500 kg. Technical specifications of the BERNARDO Variomill FU 2000E Servo milling machine - feed in the X/Y/Z axis: 1400/700/500 mm - rapi ...

Manufacturer: TOOL-TEMP Model: TT-28000 DG Type of Machine: Temperature Control System Voltage (Volt): 3-phase, 380–415 V Power (Watt): 3 × 9000 W Frequency (Hz): 50 Hz Refrigerant Gas (Gas): R-134a Refrigerant Quantity: 10 kg Find more here - / Contact us at -

Parallel Lathe JET PROMAC 941 V Between points: 500 mm Maxi Ø on bench: Ø 240 mm Maxi Ø over saddle: Ø 140 mm Spindle diameter: Ø 21 mm Spindle speed: from 100 to 1700 RPM Square turret Chuck: 3-jaws Ø 125 mm Year of construction: 2012 - Almost new Spindle motor: 1,3 kW Threadings: Metric + Whitworth Tailstock: CM2 Variable speed drive for the spindle Supplied with one 4-jaws chuck Ø 125 mm Supplied with the gears for threading Electronic tachometer Voltage: 220 V mono Dimensions (L x W x H): 1200 x 600 x 1400 mm Weight: approx 200 kg

Key data: 500 mm, 400 mm, 400 mm

Deckel FP 4M Active with 3-axis active digital display, Year of manufacture 1996 Table clamping area 800 x 460 mm Travel X / Y / Z 500 / 400 / 400mm Spindle speed 50 - 2500 rpm Feed rate 8 - 630 mm/min Rapid traverse 1500 mm/min Quill stroke 90 mm Tool holder SK 40 Hydraulic Tool Clamp Very good condition!

GeneralVertical Machining centre; Control: DMG MORI ERGOline IV Multi-Touch CharacteristicsTable surface900 x 600 mmTool Magazine with30 PositionsMovement X / Y / Z600/600/510 mmRapid feed X / Y / Z30/30/30 m/minAC main driveSpindle speed range 20 to 15.000 rpm AC main drive:20/14,5 kW (40/100% DC) Tool taper SK40 DIN 69871 Tool clamping according to DIN69872Direct measuring system X,Y,ZDirect Measuring System X, Y, Z inclusive Air Purge for Measuring SystemTouch Probe Heidenhain TS 460Touch Probe HEIDENHAIN for workpiece measuring Option includes: - TS 460 Touch probe with optical signal transmission - measuring cycles - calibration ring - case for equipmentTouch probe Heidenhain TT160Touch Probe HEIDENHAIN for tool length and diameter measurement Option includes: - TT160 probe for tool measurement - measuring cycles with tool breakage monitoring - calibration tool Note: Additionally to ...

CharacteristicsTable surface900 x 600 mmTool Magazine with60 PositionsMovement X / Y / Z600/600/510 mmRapid feed X / Y / Z42/42/42 m/minGeneralVertical Machining centre; Control: DMG MORI ERGOline IV HEIDENHAIN TNC 7 Spindle speed range 20 to 12.000 rpmSpindle speed range 20 to 12.000 rpm AC main drive:13/9 kW (40/100% DC) Tool taper SK40 DIN 69871 Tool clamping according to DIN69872Direct measuring system X,Y,ZDirect Measuring System X, Y, Z inclusive Air Purge for Measuring SystemProduction Package 80 barProduction Package 80 bar Option includes: - Internal coolant supply 80 bar - Tank capacity: 600l with papertype filter - Chip conveyor (scraper type) with tank capacity: 200 l (left) - Bed flushing via M-Function - Coolant spray gun for swarf removal - EActive cooling systemActive cooling system for selected mechanical components in order to increase machine thermal stabilityAir coola ...

Turning diameter: 320mm, turning length: 1000mm, spindle clearance: 80mm, speed: 3150rpm, travel X/Z: 265mm/1000mm. Machine dimensions X/Y/Z: approx. 5500mm/2400mm/2400mm, weight: approx. 7000kg, control: Traub System TX-8. Including a tool set, three-jaw chuck and bar chuck with collets. Documentation available. On-site inspection is possible.

Key data: 140 °C, 10 kW

Max. heating capacity - 140°C Heat transfer medium – water Power: 10 kW Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended

Univ. swivel, tilt and turn tableAttachment table for Univ. tool barrel machineTable size 630 x 250 mmGroove width 14 mmRotatable and tiltable +/- 30Swivel +/-45- 4x T-grooveWeight approx. 120 kg; used

Key data: 140 °C

Temperature control unit of the tools - Tool Temp TT-118K / MP-988 (3 pcs.) Year of Make: 2020 Location: Lodz, Poland Description: Max. heating capacity - 140°C Heat transfer medium - water Power: 29.3 Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended All offered devices are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected device or to participate in live technical tests at our company in Łódź. Price: On request

Key data: 160 °C, 20 kW

Temperature control unit of the tools - Single STW 180/1-18-70-N1.1 (2 pcs.) Year of Make: 2013 Location: Lodz, Poland Description: Max. heating capacity - 160°C Heat transfer medium – water Power: 20 kW Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended All offered devices are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected device or to participate in live technical tests at our company in Łódź. Price: On request

Key data: 140 °C, 10 kW

Temperature control unit for tools - Wittmann Tempro Plus (15 pcs.) Year of manufacture: 2009-2018 Location: Lodz, Poland Description: Max. heating capacity - 140°C Heat transfer medium – water Power: 10 kW Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended All offered devices are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected device or to participate in live technical tests at our company in Łódź. Price: On request

Key data: 90 °C, 10 kW

Temperature control unit for tools - Wittmann Basic-C90 Year of Make: 2015 Location: Lodz, Poland Description: Max. heating capacity - 90°C Heat transfer medium – water Power: 10 kW Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended All offered devices are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected device or to participate in live technical tests at our company in Łódź. Price: On request

Key data: 90 °C

Temperature control unit of tools - Tool Temp TT-188 (20 pcs.) Year of construction: Location: Lodz, Poland Description: Max. heating capacity - 90°C Heat transfer medium – water Power: 9850 watts Device has: - a vacuum pump - a vacuum chamber - a function to suck medium out of tools - The device can be integrated with the machine, unattended All offered devices are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected device or to participate in live technical tests at our company in Łódź. Price: On request

Linear unit, linear axis, portal axis with servo drive, synchronous servo motor, electric slide, loading unit, linear guide with servo motor and pneumatic gripperREXROTH INDRAMAT Type: MKD0771B-061-KP1-KNIdent No. 247238 0001Year of construction: 2000Axis movement: 2400 mmCarriage length: approx. 500 mmTotal length: 3520 mm- pneumatic feed pliers (clamping pliers with 2 Festo compressed air cylinders)- Standard linear guide 65 x 25 mm- basic profile made of steel- ball screw 32 x 10 mm- pneumatic with position indicator- Permanent Servo Motor Type:

Univ. swivel, tilt and turn table presumably DECKELUniversal tool milling machine attachment tableTable size: 700 x 400 mmGroove width: 14 mmGroove spacing: 46 mmMounting plate: width 550 mm x height 300/240 mm- Swivel and tiltable +/- 30- Rotatable 360Weight approx. 140 kg; used

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 33064 Year of construction approx. 1960 Overhauled in 2012Travel distances X: 300 mm Y: 150 mm Z: 330 mmTable size 600 x 210 mmSpindle holder MK 4 - S20 x 2Spindle speed vertical 95-1900 rpm. 12 stepsSpindle speed horizontal 60-1200 rpm. 12 stepsMotor power 1.1 and 1.4 kWNerg connection 380 volts, 50 Hz- Feed in the X and Y axis- Pinol displacement on the vertical milling head- Fixed angle table- Coolant device with mechanical pump in the machine foot-

Univ. Swivel, Tilt and Turn Table DECKELUniversal Tool Milling Machine Attachment Table suitable for FP 2L or FP 3L or FP 4LNr. 2314-0301 Year of construction: approx. 1975Clamping surface: 1000 x 520 mm- 6 clamping grooves 16 mm, distance 90 mm- Clamping plate can be rotated horizontally to the right and left up to 45 degrees- Tiltable from/to the machine +/- 15 degrees- Swivel +/- 15 degrees- Swivel table, tilting table, angle tablePermissible load max. 1000kgWeight: 400kggood condition; used

Hydraulic power unit with hydraulic pump BOSCH REXROTHHydraulic power unit Year of construction approx. 2000Operating pressure pump1: 10 barVolume flow pump1: 24 litres/min. Engine power pump1: 1.5 kWoperating pressure pump2: 120 bar (max.140 bar)Volume flow pump2: 44 litres/min. Engine power pump2: 11 kWTankle capacity: 200 litresMains connection: 400 volts, 50 Hz- 2 independent hydraulic pumps, each with its own drive motor- 6 hydraulic valves built- Cleaning cover in the oil tankSpace requirement L x W x H 1000 x 700 x 1200Weight:

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 52185/08 Year of construction 1968Travel distances X: 300 mm Y: 150 mm Z: 340 mmTable size 600 x 250 mmSpindle holder SK 40 - S20 x 2Spindle speed 40-2000 rpm. 16 stagesMotor power 1.0 and 1.4 kW pole-switchableMains connection 380 volts, 50 Hz- Feed in the X and Z axis- Two motor speeds and 8 gear stages- Pinol shift on the vertical milling head 60 mm- Fixed angle table- Coolant device in the machine foot- Adjacent control cabinet- Counter holder

Univ. tool milling machine directly from one resolutionMilling machine DECKEL type FP 4Masch. No. 1/0687 Year of construction 1978Travel X: 700 mm, Y: 400 mm, Z: 450 mmTable clamping surface 860 x 500 mmSpindle holder SK 40 - M16Spindle speed 31.5 - 1600 rpm. 18 stepsQuill displacement horizontal and verticalMain spindle drive 4 kWNet connection 380 volts, 50 Hz- Digital display 3-axis HEIDENHAIN- Universal swivel-tilt turntable- Coolant device in the machine base- Machine vice- none

Clinch unit TOX - Pneumatic-Hydro Tox pressHydro-pneumatic press TOX Pressotechnik POWER PACKAGEType type CRS 03.62No.: 207599.2Year of construction approx. 2005Pressure capacity: max. 80 kN = 8 tonProjection: 20 mmInstallation height: 32 mm- Built-in clinch tool- pneumatic valve for control- Push-through joining or clinching- For making a form-fit connection of 2 sheets without perforating or heating the sheets- Mounted on the stand- with the simplest electrical control and Foot switchWeight: 230 kgComes from

Welding turntable - Welding rotary device with housingRound welding deviceLoad capacity approx. 50 kgTurning chuck diameter 300 mmTurning chuck speed 1.0-15 rpm. Mains connection 230 volts, 50 Hz- Spiral lathe chuck with inwardly stepped chuck jaws- Speed control infinitely variable via potentiometer- Drive via gear motor, direction of rotation left- Start via electric switch- Welding current transmission with sliding contact- Extraction connection 160 mm- Interior lightingDoor opening W x H 715 x 1060 mmInterior dimensions W x D x H

Slot head for milling machine, milling head, CCCP / USSR STANKO Type 1502Nr: 200 Year of construction 1974Stroke size: max. 60 mmStroke rate: approx. 200 - 500 strokes/min. Tool holder: 12 x 17 mm with clamping plateHole spacing machine-flange plate: 245 x 185 mmMounting hole: 17 mmCentering diameter on the machine flange plate: 190 mm- Stroke size adjustable via eccentric adjustment- The drive is as with the normal vertical head from the machine gearbox- Drive via driver, centric in the centering diameter- Degree scaling at the

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 51265/08 Year of construction approx. 1967Travel distances X: 300 mm Y: 150 mm Z: 340 mmTable size 600 x 2100 mmSpindle holder SK 40 - S20 x 2Spindle speed 40-2000 rpm. 16 stagesMotor power 1.0 and 1.6 kW pole-switchableMains connection 380 volts, 50 Hz- Feed in the X and Z axis- Spindle speed over 2 motor speeds and 8 gear stages- Pinol shift on the vertical milling head 60 mm- Fixed angle table- adjacent control cabinetSpace requirement L x W x H 1100 x

Hydraulic power unit with hydraulic pump BOSCH REXROTH / HYDRONORMAHydraulic power unit Year of construction approx. 1985Operating pressure: max. 65 barVolume flow: 20 litres/min. Fuel tank capacity: 110 litersEngine power: 3 kWMortor speed: 1440 rpm. Mains connection: 400 volts, 50 Hz- 1 piece hydraulic vane pump MANNESMANN REXROTH, type 1PV2V3-40/25RA01MC63A1- 1 piece drive motor KATT, type FFN 100L- 1 piece pressure reducing valve BOSCH REXROTH, type DR 8 G433/100 YM- 1 piece return filter- 1 piece 4/2-way hand valve (e.g. for retracting and extending a double

Hydraulic power unit with hydraulic pump RACINE / VICKERSHydraulik gensetOperating pressure: max. 44 barVolume flow: 13 litres/min. Tank capacity: 40 litersEngine speed: 950 rpm. Engine power: 0.75 kWNetz connection: 380 Volt, 50 Hz- 1 piece hydraulic vane pump PVQ-PSS=-06CR-J11- Hydraulic tank with maintenance cover and oil level sight glass- 2 pieces hydraulic hoses with 12L connections, length = 950 mmSpace requirement L x W x H:: 700 x 400 x 750 mmWeight: 97 kg (without oil content); used

Table unit from a DROOP & REIN portal milling machineClamping plate with T-slots made of cast steel-gray cast ironTable unit with clamping plate and very solid guidewayTable clamping surface 5500 x 2000 mmTravel distance of the table clamping plate approx. 3100 mmTable height-height 1050mmTable load: max. 20 ton. Ball screw: 100 mmThread pitch: 20 mm (single)- Machining table very stable on the bed- Metal telescopic guideway cover - comes from a DROOP & REIN portal milling machine- Longitudinal table movement over

Universal temperature control unit WEINREICH type WTD 4Temperature control unit with electric heating and connections for external coolingFabr. No.: 11932217 year of construction 1993Temperature max. 140CBorcing pressure max. 6 barPump capacity 30 l/min. Tank volume 4 litresHeating capacity 4 kWeergisation capacity heat exchanger 15 kWCotor capacity of the pump 0.37 kWUmrune water supply + return G 3/8Cooling water flow + return G 3/8Total capacity 4.4 kWNe-connection 380 volts, 50 Hz, CEE plug-in temperature control medium water

Filter fitting, filter unit COMPAIR for compressor systemsCompressed air filterType: CF 0087B ZPFabric no: 3363006 / 05 / 005Operating pressure: max. 16 barThreaded connection: G 1 1/2Flow rate: approx. 8.5 m³/min Filter element no: CE 0087B- Filter housing made of aluminiumWeight: 5 kgDimensions L x W x H 125 x 110 x 420 mmgood condition; used

Universal face and boring head LENZ type LPA 1SSpindle tool, spindle head similar to WOHLHAUPTER UPA3Tool holder: SK 40 - M16Adjustment accuracy: 0.01 mm- Accessories as shown- Storage boxWeight: approx. 5 kggood condition; used

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 34338 Year of construction approx. 1965Travel distances X: 300 mm Y: 150 mm Z: 340 mmTable size 600 x 200 mmSpindle holder MK 4 - S20 x 2Spindle speed vertical 95-1900 rpm. 12 stepsSpindle speed horizontal 60-1200 rpm. 12 stagesMotor power 1.0 and 1.5 kW pole-switchableMains connection 380 volts, 50 Hz- 3-axis digital display HEIDENHAIN, type VRZ 753 B- Spindle speed over 2 motor speeds and 6 gear stages- Feed in the X and Z axis coolant device with

Univ. Tool Milling Machine DECKEL Type FP 1Masch. No. 28317 Year of construction approx. 1960Travel distances X: 245 mm Y: 150 mm Z: 340 mmTable size 600 x 210 mmSpindle holder horizontal MK 4 - S20 x 2Spindle speed vertical 95-1900 rpm. 12 stepsSpindle speed horizontal 60-1200 rpm. 12 stepsMotor power 0.8 and 1.1 kW pole-switchableMains connection 380 volts, 50 Hz spindle speed over 2 motor speeds and 6 gear stages- Feed in the X and Z axis coolant device with mechanical pump in the machine base

Cooling unit, cooling water recirculating cooler, water cooler, chiller O. HellwigYear of construction: approx. 1995Cooling capacity approx. 6 kWNight cooling unit 3 kWaverse refrigerant R422DWasser tank capacity approx. 35 litresFlow volume circulation pump 40 litres/minPump capacity 0.63 kWWasser connections 1/2 inchMains connection 380 volts, 50 Hz- temperature setting via rotary potentioSpace requirement L x W x H 1100 x 750 x 140 mmWeight 285 kg; used

Hydraulic punch, punching rack for the use of punching units JOKA type HP-SHydraulic hole punch, hydraulic press for punching bracketYear of construction approx. 1995Printing capacity 5 ton. Projection 155 mmStroke approx. 20 mmPunching unit width max. 54 mmPunching unit height max. 220 mmDie holder 48 mmMotor power 1.5 kWNeching connection 230 volts, 50 Hz- for the universal use of punching units JOKA SW 20 or SWD 20- Projection of the punching units can be larger, can be pushed through to the rear- Stroke release via

Univ. NC Tool Milling Machine KUNZMANN Type WF 3/4Masch. No. 341020 Year of construction 1998Travel distances X: 400 mm Y: 320 mm Z: 400 mmTable size 650 x 350 mmSpindle holder SK 40Spindle speed 40 - 2500 rpm. Feeds X, Y and Z axis 0 - 1000 mm/min. infinitely variableRapid traverse X, Y axis 4000 mm/min. Rapid traverse Z-axis 3000 mm/min. Quill adjustment vertical 60 mmDrive power Spindle motor 3 KWnet connection 400 volts, 50 Hz- CNC line control Heidenhain TNC 124- Spindle speed via 2 gear stages and

Hydraulic power unit for mobile clinching pliers or mobile former ECKOLD type HA 500 / 2Fabr. No. 737 / 783 Year of construction 1991Hydraulic power unit type HA 500 / 2Operating pressure 50 - 500 bar adjustableFlow rate 2.6 l/minTank capacity 16 litresEngine power (hydraulic) 3 kWNead power 380 Volts, 50 Hz.Control voltage 24 Volts, DC pressure line with screw coupling- With solenoid valve HAWE GS 2-2- mobile on 4 swivel castorsWeight without hydraulic oil 125 kggood condition; used