mikron 400 u used for sale

micrometer precision measuring tool factory Suhl 300 - 400 mm TGL 15046-1 pitch: 0.01 mm with protective box, dimensions: 635 x 395 x 55 mm used, tested ! Dimensions (packaging): 650 x 410 x 70 mm

Feinzeiger micrometer, with dial gauge Feinmesserfabrik Suhl 300 - 400 mm TGL 15046-1 pitch: 0.01 mm with protective box, dimensions: 700 x 390 x 54 mm used, tested ! Dimensions (packaging): 720 x 410 x 70 mm

Gear motor, electric motor, electric gear motor -Manufacturer: Groschopp, geared motor -Gearbox: Type E 2 ai= 7 -Speed speed: approx. 400 rpm -Motor: Type WK 0341501 0.12 kW / 2800 rpm -Shaft: Ø 10 x 30 mm -Protection rating: IP44 -Total dimensions: 225/150/H115 mm -Weight: 4.4 kg

Marx Transformatorenbau GmbH & Co. KG Transformer Type: DAY 516 Pri: 3x480V/777A Sec: 3x400V /909A 60Hz 630kVA Two Wöhner LTS-3 630A load disconnectors are installed at the tap, each equipped with three Siemens 400A and 630A NH3-gG.

Ismet Transformer Type: DAWT-G 40.0 SKU: 731288 Pri: 3x400V +/-5% Sec: 3x230V/3x100.5A 50/60Hz 40kVA Enclosed With circuit breaker Möller NZM N1-A100

A transformer in a SwiBox control cabinet is offered here. It is fully wired with terminal blocks and an Allen & Bradley CAT140-CMN-6300 SER C motor circuit breaker. There are three 4x10mm² cables with open ends. One FLEX-JZ in and two AWM 2587 out. The control cabinet has the compartment with transformer, terminal blocks and motor protection at the bottom and a 19" compartment at the top. The cabinet is 120cm high and 100cm deep. Everything is in very good condition. The front door opens a bit hard. PRI: 3 x 400V SEC: 3 x 208V, 3x60A 50/60Hz

Bath warmer, immersion bath warmer MAZURCZAK ROTKAPPE® B-PS 630/2,2-400Ds Item no.: 1003042001 P: 2200 W ( 2.2 kW ) U: 400 V 3AC immersion depth: 600 mm diameter: Ø 54 mm IP65 approx. 1.4 m Connection cable New ! Dimensions: 710 x 117 x 94 mm

Bath warmer, immersion bath warmer MAZURCZAK ROTKAPPE® B-WKB 350-1200/6,0-400Ds no.: 1947902017 P: 6000 W ( 6,0 kW ) U: 400 V 3AC immersion depth: 350 mm ( vertical ), 1200 mm ( horizontal ) diameter: Ø 44 mm IP65 approx. 2.8 m Connection cable New ! Dimensions: 1260 x 500 x 94 mm

DC motor, servo motor, actuator ENGEL GNM3175-G11.1 75 Watt ( 0.075 kW ) 3000 rpm Operating voltage: 24 V DC 4.1 A shaft with gear: Gear diameter: Ø 16.1 mm Gear length: 12 mm, 21 teeth flange: Ø 56 / 48.4 mm hole spacing: 70 mm 4x threaded hole: M4 x 0.7, depth: 10 mm angle between threaded holes: 90° approx. 0.3 m Connection cable New ! Dimensions: 165 x 57 x 55 mm

Lifting Magnet, Lifting Magnet, Permanent Lifting Magnet TECNOMAGNETE MAXX 1500 Load capacity: max. 1500 kg Bearing surface: 320 x 160 mm used, tested ! Dimensions ( without lever ): 400 x 170 x 300 mm Dimensions ( transport ): 430 x 400 x 300 mm

Compact cylinders, pneumatic cylinders, double-acting FESTO DNC-32-600-PPV-A 163304 1463254 piston diameter: Ø 32 mm stroke: 600 mm rod diameter: Ø 12 mm rod thread: M10 x 1,25, Length: 22 mm max. 10 bar with flexo coupling: FK-M10X1,25 ( 6140 ) used, checked ! Dimensions: 750 x 45 x 72 mm

Discharger for 2-component adhesives SULZER MIXPAC® DP 400-85-01 mixing ratio: 1:1 / 2:1 operating pressure: max. 6 bar compressed air supply: max. 8 bar with pressure relief valve ! used, tested ! Dimensions: 480 x 330 x 93 mm

Description: 4-jaw chuck Ø 400 mm, including 4x clamping jaws 2590 weight approx.: 50 kg, Approx. Onsite Dimension. (l x w x h): 660 x 470 x 350 mm

Description: 60 x LED panel 48W LED SMD 60x60 cm 4000K SUPER ECO natural white. 5800 Lumen, CRI >, 80 - SMD LED (110-240V), LED driver included, Lifespan: 30,000 hours, Beam angle: 120 degrees, Suitable for indoors. Approx. Onsite Dimension. (l x w x h): 800 x 1,200 x 1,300 mm, weight approx.: 65 kg

Description: 10 x Floodlight 400W LED waterproof IP65 - 6500K daylight - 40,000 Lumen - Size: 52.6cm x 34.5cm x 10cm - COB LED - voltage 85-265V 50/60Hz - LED driver included - lifespan 30,000 - beam angle: 110 degrees - Ra >, 80 - Suitable for indoor and outdoor use. Approx. Onsite Dimension. (l x w x h): 800 x 1,200 x 850 mm, weight approx.: 120 kg

Description: 100 x Batten light 36W LED - 120cm - 4000K Neutral white - IP20 dustproof - dim: 1200 x 38 x 61mm - AC (185 - 265V) 50/60Hz - Lifespan 30000 hours - Beam angle: 120 degrees - Suitable for indoor use Approx. Onsite Dimension. (l x w x h): 800 x 1,200 x 1,500 mm, weight approx.: 180 kg

Description: Magnetic force 40 KGF - permanent. Dense polarity for machining small and thin pieces. High-strength magnet system. Activation and deactivation by hand lever. In the OFF position, a weak reverse shot takes care of facilitating the removal of parts. With longitudinal and transverse stop. The item that is delivered is NOT the one shown in the pictures, but an equal one Approx. Onsite Dimension. (l x w x h): 550 x 350 x 110 mm, weight approx.: 70 kg

Description: Chuck for self-centering lathe 3 + 3 jaws 400 mm, body in ground cast iron, closing with helical ring, concentric manual clamping, tempered jaws The item that is delivered is NOT the one shown in the pictures, but an equal one Approx. Onsite Dimension. (l x w x h): 500 x 470 x 245 mm, weight approx.: 74 kg

S/s filter tub, inside dimensions: 3250 mm x 400 mm x 600 mm, total dimensions: 3350 mm x 500 mm x 600 mm.

Subal pre proofer, model: KN4 400, number: 0407201, year of construction: 2004, 1 kW, 400 baskets, 4 baskets per row, dimensions each basket: 200 mm x 130 mm, cloth outfeed belt, belt width: 270 mm, total dimensions: 3200 mm x 1800 mm x 2700 mm.

Verbufa forming machine, type: MFD 400, type number: 51276-C-0012, serial number: 2085952, year of construction: 2008, 230 V, 50 Hz, 10 A, dimensions: 1400 mm x 1500 mm x 1700 mm. Including 2 crates with parts.

Hein storage and pre-baking chamber, 400 V, inside dimensions: 700 mm x 1000 mm x 1950 mm, total dimensions: 880 mm x 1300 mm x 2630 mm.

A.E.W. Engineering bandsaw, model: 400, type: MK.11, serial number: LHS229791, 380 V, 4-7 A, dimensions: 1150 mm x 1000 mm x 1900 mm. Without saw blade.

A.E.W. Engineering bandsaw, model: 400, type: MK-11, serial number: LH-164 188, 415 V, 3 Ph, 6.2 A, dimensions table: 1040 mm x 900 mm, total dimensions: 1040 mm x 1070 mm x 1900 mm.

Henkelman mobile vacuum machine, type: 400, number: 40204042, year of construction: 2002, 400 V, 3 Ph, 50 Hz, 10 A, 2.7 kW, chamber: 760 mm x 510 mm, seal length: (1x) 810 mm, (1x) 510 mm, Busch vacuum pump, total dimensions: 940 mm x 770 mm x 1150 mm.

AEW-Thurne Ltd bandsaw, model: 400 Bandsaw, serial number: 1335094, year of construction: 2006, 415 V, 3 Ph, 50 Hz, 6 A, 250 kg, dimensions table: 1060 mm x 860 mm, total dimensions: 1070 mm x 900 mm x 1930 mm.

Vibronics Ultrasonic Bath Brand: Vibronics Power 1.8 kw; Serial number: 6092 Total dimensions L: 2800 mm; W: 1700 mm; H: 930 mm; Tank size: WxHxD= 1350x720x990 mm Frequency 25 kHz equipped with 4x generators

Cooling unit Water recooling unit DALEX type DRF 2 Masch. No. 38913719 Year of construction 1989 Volume flow 0.35 m3/h Cooling capacity 1950 Watt Operating pressure 2 to 3 bar refrigerant R 134a Device was converted from R12 to R134a Operating overpressure 18 bar Pipe connection thread 3/4? Tank volume 600 x 400 x 350 mm = approx. 80 litres Mains connection 380 volts , 50 Hz Space requirement L x W x H 900 x 800 x 1020 mm Weight 100 kg good condition; used

Reel on and off reel, reel GSW SCHWABE Type LHD 50/800 Probe Double unwinding reel, double uncoiler Fabr. No. 5775 Year of construction approx. 1995 Coil weight 50 kg per side Coil width max. 130 mm Coil inner diameter 155 - 445 mm Coil outer diameter 850 mm Plant discs 850 mm Start-up rings 850 Center reel shaft to reel foot 980 mm - Reel structure manually rotatable by 180 with latching steps - central spread via rotary lever adjustment - mechanical disc brake, adjustable brake shoes via knurled screw Space requirement L x W x H 1000 x 850 x 1500 mm Weight 190 kg good condition; used

Istz an air conditioning / heater, functional but unfortunately the electronics is defective! Either as a spare parts dispenser or repair electronics.

The Breaker device is used to form a foil on a roll, it enables the insertion of an opening-closing tape. The machine is powered by 380V.

size L: 2500 mm; dimension W: 2500 mm; size H: 2450 mm; Refrigeration compressor: Yes; Evaporator: Yes; total size L: 3000 mm; overall dimension W: 3000 mm; overall size H: 3150 mm; description: steel frame; cold room walls thickness 135 mm; outside cold room door; control panel; stainless steel ventilation grilles; working condition; The buyer must take care of the transport and truck with loading crane

Documents installation-drawing.pdf Technical information Physico-chemical separation / distillation unit. Year: 2015 Installation ATEX 3G IIBT4, inside the installation: zone 1G Operating mode: continuous - batch - semi-batch. Pressure: Vacuum - 3 barg max Boiler size: 50 Litres (Possible 200 Litres) Flow rates: Approximately 180 Kg/hr feeding a water/ethanol mixture (90/10) at atmospheric pressure with a reflux rate of 5. Theoretical number of trays: 20 --> Possible feeding in 3 points: 4 structured packing beds, 4 liquid redistributors (3 with recenters) Dimensions: Unit made as a skid, in hot-dip galvanised steel frame with dimensions 2400 x2400 x 4000MM high. Utilities / sources : Steam: 3 bar eff 143?C 30 to 80kg/h Cold water 25-30?C : 2-5m3/h Chilled water 5-10?C : 0.5m3/h Compressed air : 6bar eff Nitrogen inerting : 4.5 bar eff Electri ...

Previous use: distilled water Capacity: 100 L/H Material: glass Year: 1993 The unit includes : Level regulator Electrical control box Frame Pump Coil heat exchanger (1.2 bar max) Electric tank heater 5000W 200 litre glass tank Tubular exchanger (1.2 bar max) Photoelectric level Boiling chamber Stainless steel coil boiler: stainless steel 316 (1.2/1.5 bar max)

Modular unit, format processing unit, cutting unit, milling unit, profile milling unit, jointing milling unit, trimming unit, double-end profiler, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine, finishing unit, buffing unit -Manufacturer: Homag, 3 milling units and 2 buffing units from the BRANDT KS 25 edge banding machine -Buffing units: Motor KMER 0.18 kW 1360 rpm -Polishing roller: Ø 145 mm, height and depth adjustable / swiveling -Milling units: Motor Perske / Homag, see photos on nameplates -Voltage: 220 V / 200 Hz -Price / fee: complete -Dimension total. 1200/800 / H590 mm -Total weight: 243 kg

Nummerier- Perforierwerk / Imprint unit Numbering- Perforation Unit Heidelberg GTO46 Nummerier- und Perforierwerk fuer Heidelberg GTO46 Imprint unit Numbering- and Perforation Unit for Heidelberg GTO46 -Online-Video-Inspection by Skype-Video- -We would be very pleased with your visit - more machines on Stock- -Available Immediately - Can be inspect- -On Stock Emskirchen / Nuernberg - Can be test-

Nummerier- Perforierwerk / Imprint unit Numbering- Perforation Unit Heidelberg MO Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nuernberg - Can be test

The rewinder / perforator is used to rewind the foil from the thimble to the thimble with the control of the foil rewinding length. It also allows you to make perforation at a certain length. Thanks to this machine, it is possible to make very long pieces of foil, used in industry or agriculture. The machine is powered by 380V.

Used dosing unit CANOL, type: P10-E -in bakery condition- 2 pieces available - Built in 1998 and 2000 - Condition: Bakery condition, ready for immediate use - Number of nozzles: 1 piece -El. Connection: 400 V, 50 Hz, 037 kW Viewing and test run are possible by arrangement.

Manufacturer : Confitrac sprl Model: CDS-161205 Year : 2017 Type: Deodoriser Condition: new, never used. Document : CDS-P&ID-Deo-500-Electrique.pdf Installation consisting of : - A horizontal cylindrical shallow bed deodoriser divided into two horizontal compartments, supported by two supports and offering the possibility to treat either 250 kg in one compartment or 500 kg in two compartments. - A horizontal buffer tank equipped with a product inlet/outlet, vacuum outlet and sight glass. Volume: +/- 460 litres. - 2 shell and tube heat exchangers - 1 electric heater - 2 electric heating resistances - Other equipment: control and dosing valves, flow meter, steam drying ramp, etc. - Electrical cabinet Materials: all parts in contact with the product are made of stainless steel 304L and 316L. Insulation: 100 mm rock wool. Documentation and drawings available.  ...

Maho MH 600P X: 500 - Y: 400 - Z: 400 mm Max longitudinal travel X-axe: 500 mm Max cross-travel Y-axe: 400 mm Max travel Z-axe: 400 mm Power on spindle: 5,5 kW Admission in boring head (ISO): SK 40 Spindlespeeds: 20 > 2000 rpm Table size: 720 x 410 mm Digital screen: Heidenhain 3 axes Length: 1800 mm Depth : 1500 mm Height: 1800 mm Weight: 2 ton

Punching units, punching unit, punching bracket, punching tool, non-driven clinking and shearing units, forming bracket -Manufacturer: SUPRA, punching bracket GN4 type PA80 400 with punching tool -Throat: 400 mm -Punching capacity: mm -Matrix: Ø 75 mm -Dimensions: 570/120/H140 mm -Weight: 27.6 kg

Kallfass Universa 400 with shrink tunnel and grab section Kallfass Universa 400 Year 2006 The system is immediately available. The Universa 400 is included in the price of the complete system. The machine is technically overhauled and is in very good condition. Technical data: - Length of cross welding punch: 450mm - Welding punch passage: max. 200mm - Min. product length: 80mm - automatic length compensation to reduce the punch gap - Welding punch monitoring - Control: Siemens S7-300 - Operating terminal with Siemens touch panel - Welding punch with replaceable welding strip - Side welding knife combination, can also be exchanged for a wheel knife system - Processable films PE and PO - Year of construction 2006 - Kallfass Compact 450 SO shrink tunnel - Gripper section with inline belt - Book magazine on gripper section - Ionization for blocking loose leaves - Cur ...

Kallfass Universa 400 with shrink tunnel, SlipTorque roller belt and conveyor belt Kallfass Universa 400 built in 2005 The system is immediately available. The price of the complete system includes the Universa 400, the Schlichter shrink tunnel, a SlipTorque roller belt and a conveyor belt. The machine is technically overhauled and is in very good condition. Technical data: - Length of cross welding punch: 450mm - Welding punch passage: max. 200mm - Min. product length: 80mm - Metronic embossing system - Control: Siemens S7-300 - Siemens Touch TP277 operator terminal - Welding punch with replaceable welding strip - Side welding knife combination, can also be exchanged for a wheel-knife system - Processable films PE and PO - Year of construction 2005 - Simple shrink tunnel DS-600 with switchable rotating bars - Conveyor belt 1000 x 400mm - SlipTorque roller conveyor 2 ...

Used thermoshrink packaging machine by Kallfass UNIVERSA 400 ECO including shrink tunnel Compact 450-SO.

General SKU098A526 LocationBarneveld MakeRPA Aoustin Process Technologies Darnetal TypeNovamix NX-400 Mach.No.891-A Pressure Working pressure jacket2 Bar Main Features MaterialStainless steel Volume400 Ltr. Motor30 KW Specified Features - Universal mixer MaterialStainless steel 1.4404 (316L) Universal mixer(1x) Capacity400 Ltr Vessel sizesdia. 915x700mm With covercheck Pneumatic operated outletdia. 200mm With jacket(24 Ltr) With motor30,0 KW (Ex) With lump breakercheck With motor5,5 KW, 380 Volt (Ex) Information Year of construction2002 Floorspace2,5x2,3 M Total height2,6 M Weight3600 KG ATEX compatiblecheckUniversal mixersRpa AoustinMixers > Universal mixersBrand > Rpa Aoustin What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspec ...

General SKU213W136 LocationBarneveld MakeDiosna TypeP-400A Main Features MaterialStainless steel Volume400 Ltr. Motor24 KW Specified Features - Universal mixer Universal mixercheck Capacity360 Ltr. (max. 400 Ltr.) Vessel sizesDia. 1200x617 mm With covercheck Inletdia. 820 mm Pneumatic operated outletcheck Outletdia. 290 mm With motor21/24 kW Rotor speed65-130 rpm With lump breakercheck With motor4/5,2 kW Rotor speed1500/3000 rpm MaterialStainless steel 1.4301 (304) Information Mach.No.250-037 Mounted on framecheck Mounted on legscheck With switchgearcheck Floorspace2,50x1,90 m Total height2,60 m Weight2100 kgUniversal mixersDiosnaMixers > Universal mixersBrand > Diosna What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the m ...

Description: Grinding length: 320 mm center height: 100 mm Center width: 400 mm Swiveling screen cover Incremental measuring system with digital display Machine light Grinding spindle speed: 1800 - 1970 - 2170 1/min Grinding wheel large: 350 mm Grinding wheel small: 250 mm Max. Width: 50 mm Coolant capacity: 180 liters Filtering capacity: 60 l/min Internal grinding device: 25000 1/min Approx. Onsite Dimension. (l x w x h): 1,800 x 1,700 x 1,600 mm, weight approx.: 2,000 kg

Description: Center height 100 mm Center width 400 mm grinding length 320 mm grinding wheel speed: 1800 / 1970 / 2170 rpm grinding spindle motor 3 kw internal grinding spindle 22000 / 28000 rpm internal grinding diameter 8 - 60 mm grinding depth 14 - 60 mm Approx. Onsite Dimension. (l x w x h): 1,800 x 1,700 x 1,600 mm, weight approx.: 2,000 kg