mi used for sale

26,000 litre milk tank / agitator tank / storage tank made of V2A Properties: Volume 26000 L Material V2A (AISI 304) 1.4301 Total height 7200 mm Cylinder height 4500 mm Diameter 3400 mm Surface outside 2B=IIIC ground Surface inside 2B=IIIC ground Description: Topsoil: Clapper bottom 2 crane eyes Level measurement 1/2" CIP line with CIP cleaning Tank cylinder: Manhole 450 x 370 mm Agitator mixer Stelzer type SN-63 H D2 - side with propeller (for tank ST2 right, for tank ST1 left) Socket 1/2" Subsoil: Clapper bottom with foot ring Outlet surround with flange connection Sensor for level measurement Important note: The agitator installed here contains a seal that must be protected from dry running.

Key data: 600 mm, 400 mm, 310 mm

A Mitsubishi MV2400R is being sold Travel: X-axis: 600 mm Y-axis: 400 mm Z-axis: 310 mm U/V axis: +/- 75 mm Type: 4-sided frame table hardened with automatic adjustment Vertical sliding door as a water bath machine Table size: 840 x 640 mm Workpiece sizes: max. 1050 x 820 x 305 mm Workpiece weights: max. 1500 kg Wire ̄: 0.1 to 0.3 mm for wire coil holder 10 kg Control: MITSUBISHI M800 with 19" Full-Touch Monitor (incl. hand pilot with configurable LCD monitor) Closed control loops min. axis resolution 0.05 μm Generator: Fine finishing generator H-FS AE II Digital Generator Equipment: Tubular drives with linear scales (X/Y/U/V) Hand-held pilot with configurable LCD monitor 20-kilo wire station Angle Master Advance II Set Wear parts box Ergolux Lamp Corehold function Job Planner Filter Pump Pressure Sensor Operating data output Free software update if needed  ...

3-storey tank / agitator tank / storage tank made of V2A 60,000 + 60,000 + 30,000 liters = 150,000 liters Properties: Volume 150,000 L Tank chamber 1 30000 liters Tank chamber 2 60000 liters Tank chamber 3 60000 liters Manufacturer: rind Milfor Total height 20000 mm Material V2A (AISI 304) 1.4301 Surface outside bright rolled 2b Surface inside bright rolled 2b Inner diameter 3650 mm Outer diameter 3750 mm Number of feet 6 Last use Acid, lye Weight 16000 kg Description Caustic Tank K1 Factory No. 3341 Ab. Re: Temp. 4÷ 95°C Insulation made of PU rigid foam panels Dimensions per hive tank: Tank chamber 1 for return water: Volume: 30,000 liters Height: 3,600 mm Inner diameter: 3,650 mm Tank Chamber Description: Cone bottom on topsoil N6 - Overflow DN 100 N2 - DN 300 Ventilation with vapour drain N3 - DN25 CIP with inlet pipe DN 50  ...

Microstep MG 6001.25 PRBG Working Area : 6000mm x 2500mm Kjellberg 360i with automatic gas console With rotator 1 x Autogenous 1 x drilling unit with tool changer Including filter system more information on request

16,000 litre milk tank/ agitator tank / pre-stacking tank Properties: Volume 16000 L Material V2A (AISI 304) 1.4301 Total height 3500 mm Cylinder height 2800 mm Inner diameter 2900 mm Outer diameter 3100 mm Surface outside 2B=IIIC ground Surface inside 2B=IIIC ground Description Tank was used for the pre-stage of finished product. Topsoil: Inclined cone base 2 crane eyes CIP Cleaning Vent nozzle Thermometry Tank cylinder: insulated 6 cm Manhole 450 x 350 mm Agitator mixer Stelzer type DRK6P/12 with propeller CIP ball under the agitator Thermometry Level measurement Subsoil: Flat bottom with 3% slope Residual drain pipe with flanges Motor Tank 1/4 - Agitator to the left of Manhole Agitator Mixer Stelzer Type DRK6P/12 No.39139 IP44 Re Art. S1 7.571.5 kW 970/480 rpm 50 Hz 380 V YY/Y switch. 16 ...

A machining center Chiron, which was completely overhauled in 2013, is available. Travel path X/Y: 6000mm/630mm, rapid traverse: 60m/min, tool positions: 92, tool holder: HSK-A63, speed: 12000rpm, torque: 140Nm, milling axes: 5, weight: approx. 20000kg, control: Siemens S840D, operating hours: 77344h. Includes scraper belt conveyor, OKZ preparation, Knoll VRF 250 vacuum rotary filter, high-pressure pump (70bar), emulsion mist extraction (2x800m³/h), central partition for pendulum machining, hydraulic unit (210bar), and Kohn linear clamping system with 8x hydraulic vices Multi 2000MFS 125/680 HD. Documentation available. An on-site inspection is possible.

Punching force: 400 kN (holes e.g. 20 m in 15 mm steel) Cuts 150 x 10 mm on the flat steel shear With pipe notch on the steel bar shears Foot switch for stroke release Support table on the punching side Quick-change device Range of tools is included in the price

Cooling Capacity : 206 RT Total Input KW : 119.1KW KW/Tons : 0.5774 Fluid Flow : 124.5 M3/hr Incoterm: EX WORK Currency: USD Commercial: Aaron Tan (yytantopglove.com.my)

WITH HOT FOIL STAMPING DEVICE M. No.: T171 074 N Format: A4 Number of colors: 1

Two semi-automatic angle welding machines Minipack with L-seal for shrink film are available. Packaging capacity: 900 packages/min, sealing bar dimensions X/Y: 840mm/600mm, max. film roll diameter: 300mm, max. film roll width: 800mm, working table height: 930mm, machine dimensions X/Y/Z: approx. 2100mm/1000mm/1250mm, weight: approx. 250kg. Documentation available. An on-site inspection is possible. Sale of individual units is possible.

frequency: 50 Hz weight of the machine ca.: 2,510 t dimensions of the machine ca.: m 3-axis machining centre Microcut Challenger 2412 Technologies: Drilling / thread machining, form milling (3 D), milling, HSC milling without vice Table Size: 30 x 14.3 Max Table Load: 550 LBS X Axis: 24 Y Axis: 12 Z Axis: 20.47 Spindle Speed: 8,000 RPM Spindle Taper: 40 Spindle Motor: 5.5 HP ATC: 16 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Groove/Perforating Machine Petratto Minibat 2; cleaned and tested; Working width 450mm; Format max.700x450mm, min.200x150mm; Creasing distance 0.1mm; Sniffer; Program memory; Incl. Grooving tool; Rental possible. Creasing and perforating machine Petratto Minibat 2; cleaned and checked; workimg width 450mm; size max.700x450mm, min.200x150mm; Creasing distance 0.1mm; vacuum feeder; program memory; incl. creasing tool; can be rent.

For sale are intercoolers from a Mitsubishi S12R. The coolers were subjected to a test run ex works. When they arrived at our place, they were dismantled and stored. Traces of storage available Condition: as good as new (test run ex works) Model: S12R Part Number: 37755-10101 Alternative: 37755-20100 37755-20010

Manufacturer: MINOX Type: MTS 2000/1 Built in 1999 Surface: 2.5 m² Dimensions diameter: 180 cm Weight: 1200kg Space requirement: 240 cm x 240 cm Available quantity: 2 pcs. Condition: used, fully functional

Compressor COMPAIR L22 SR-10 Volume 2.86 m³/min Properties: Identification number 100016088/0009 Built-in compressor 6115 Order no. 10698941 Compression medium AIR/LUFT Length 800 mm Width 700 mm Total height 1400 mm Weight 355 kg Volume flow 2.86 m³/min Suction pressure 1 bar Step pressures 10 bar g Speed 3600 min ̄¹ Installed motor power 22 kW Voltage 400 V Phase 3 Ph Frequency 50 Hz

x-travel: 6000 mm y-travel: 630 mm z-travel: NC-Schwenkkopf mm Control: total power requirement: -- kW weight of the machine ca.: 19,5 t required space: -- m Condition: Used Specification: Vertical CNC machining center Chiron MILL 6000 high speed with NC swivel head Year of manufacture 2004, completely overhauled in 2013 by the manufacturer Chiron - Siemens 840D (PCU50, NCU572.4) - NC swivel head - Long part machining up to max.: 6,000 mm - Machining of the front side, horizontal with swivel head right/left - Pendulum machining via center partition wall max.: 1,773 mm - 4 hydraulic double vices - High-speed package: - Motor spindle D 12,000 rpm, 140 Nm - Travel distance X: 6,000 mm / Y: 630 mm - Rapid traverse in X/Y/Z: 60 m/min - Production package: - Crown belt conveyor, ejection height 1,050 mm - IKZ preparation - KNOLL VRF250 vacuum rotary filt ...

Manufacturer: Chiron Model: MILL 6000 high speed with NC swivel head Year of Manufacture: 2004 Major overhaul: 2013 Operating hours: 77,374 h Weight: 19,500 kg Power Supply: 3/N/PE ~ 50/60 Hz Working Voltage: 400 V Control Voltage: 220/24 V Power Consumption: 52 kVA Rated Current: 75 A Fuse: 80 A Last spindle replacement: March 2021 (approx. 7,300 spindle hours since) Technical Data: - Control: Siemens 840D (PCU50, NCU572.4) - NC swivel head - Travel paths: X 6,000 mm / Y 630 mm - Rapid feed: X / Y / Z = 60 m/min - Motor spindle: 12,000 rpm, 140 Nm - Tool change time (chip-to-chip): 3.0 sec (vertical), 4.7 sec (horizontal) - Tool magazine: 92 tool positions, HSK-A63 Find more here - / Contact us at -

Coordinate measuring machine Inv. Num. : 8632 Type: MICRO-MS 343 Producer: Tesa Created: 1997, GO 2020 Parameters: Machine dimensions: 800x750x1370 mm New Reflex system

Assortment of measuring tools, calipers Digital depth caliper Mitutoyo 571-203-10, measuring range 300mm Digital gate valve Garant 412601/150 (manufacturer probably Mitutoyo), measuring range 150mm Digital caliper unknown, measuring range 150mm Analogue caliper Expert, measuring range 300mm The batteries have been renewed or are in order. The measuring tools can be demonstrated on site by appointment. We offer only machines that are ready for demonstration in our warehouse, see "other offers of this year". provider".

Two digital calipers Digital caliper Mitutoyo 551-231-10, measuring range 300mm Digital caliper Mitutoyo 500-181-U, measuring range 150mm The batteries have been renewed or are in order. The measuring tools can be demonstrated on site by appointment. We offer only machines that are ready for demonstration in our warehouse, see "other offers of this year". provider".

Number of spindles: 5 St. Working width: 240 mm Working height: 120 mm Length of the planing table: 2500 mm Feed motor: 4 kW Feed speed: 6-36 m/min. Weight: ca. 3500 kg control: SCM Control 10 SCM Superset NT with workpiece return ---------------------------------- The machine is in cleaning and completely checking process at the moment. Brief Summary: ---------------------------------- - 5 spindles - Powerful motors - Left and upper spindles controlled for width and height - With workpiece return to the operator 1st spindle ---------------------------------- First lower horizontal spindle Motor with brake 7.5 kW Diameter 40 mm Speed 6,000 rpm 2nd spindle ---------------------------------- First right vertical spindle Motor with brake 7.5 kW Diameter 40 mm Speed 6,000 rpm T-set quick-clamping system 3rd spindle ---------------------------------- First left vertical spindle Motor with bra ...

x-travel: 560 mm y-travel: 500 mm z-travel: 400 mm Control: TNC 360 spindle speed:: 40-4.000 U / min total power requirement: 7,5 kW weight of the machine ca.: 2,6 t dimensions of the machine ca.: 2,6 x 1,8 x 2,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning length: 600 mm turning diameter over bed: 360 mm turning diameter over slide rest: 190 mm bed width: 295 mm number of spindle speeds: 45 - 2240 U/min. spindle bore: 33,0 mm tailstock quill taper MT: MK 3 feed: Längs 0,02-0,8 mm/U feed: Quer 0,0125-0,5 mm/U total power requirement: 5,5 kW weight of the machine ca.: 1900 kg range L-W-H: 2050 x 950 x 1280 mm Refurbished and repainted in 2013 Costs around 16.000 euros Furnishing: - WNW NILES 3-jaw chuck Ø 200 mm - Multifix steel holder size B with inserts - revolving center points - chuck key - Movable tailstock - Operation manual The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 4.0 mm : 3.0 mm : 30 - 120 Grad blade length: 150 x 150 mm work height max.: 900 mm table:: 1000 x 650 mm engine output: 3.0 kW weight: 850 kg range L-W-H: 1250 x 1000 x 1160 mm Furnishing: - Notching machine with angle adjustment 30° - 120° - Simple and functional Touch Pad control panel Set-up stroke Single stroke continuous stroke - Plexiglas protection for better transparency - hardened knives also for cutting stainless steel - planed table surface to avoid tilting or slipping of the metal sheet - adjustable lift height adjustment - Waste bin - free-moving footswitch - Operation manual BOSCHERT angle adjustment: - the one-piece 30° upper knife is within one tool both with a left and directly connected to a right lower knife - once for each notch over 30° left and once on the right. - the swivel adjustment becomes pneumatic, immediately after completion of the first notch, ...

Fully automatic sheet dispenser PAL-Cut 800 The Palcut 800 cuts paper quickly and precisely into intermediate sheets of the desired length, directly from the roll. Fully automatic sheeter PAL-Cut 800 sheet dispenser, which cuts intermediate layers quickly and precisely in the desired length. The sheet dispenser is suitable for continuous operation in an automatic palletizing system and for companies with high sheet consumption. The Palcut 800 works with rollers of max. 800 mm width. Type designation: PAL-Cut 800 Length: 1853 mm Width: 1380 Height: 1739 for roll width up to: 800 mm Mounting height: 1,368 mm Working speed: 480 pcs/h Power connection: 220 V, 0.18 kW Operating mode: fully automatic Weight: 370 kg Link PAL-Cut 800 More items - new and used - can be found in our shop! International shipping costs on request!

CNC vertical machining center Type: Mikron VCE 800 Pro Manufacturer: GF AgieCharmilles Year: 2011 Control: Heidenhain iTNC 530 X: 800 mm Y: 500 mm Z: 540 mm Table: 910 x 500 mm Max table load: 1100 kg Max spindle speed: 14000 rpm Tool magazine: 24 positions Machine weight: 5000 kg Cooling and rinsing through the center of the spindle. Work and tool probe included New spindle in 2018 Machine in good condition, under power Find more here - / Contact us at -

Table sheeter Fritsch Mini 520 0.5Lx0.5L Year of manufacture: 2013 Machine technically checked-cleaned with dry ice. Belts have signs of wear. Machine tested

Properties: Length 1000 mm Width 650 mm Total height 1000 mm Operating temperature range 80° C Working overpressure range 5 bar Volume 2000 L Material V2A (AISI 304) 1.4301 Fabr No. 30178 Ab. Operating overpressure 5 bar Ab. Operating temperature 80°C

x-travel: 200 mm y-travel: 60 mm z-travel: 500 mm speed of measurment: 0,02 - 20 mm/s 0: X = 0,05 µm 0: Z = 1 µm mg traversing speed: X = 0 - 80 mm/s base plate: 600 x 450 mm weight of the machine ca.: 164 kg dimensions of the machine ca.: 766 x 482 x 1166 mm CE signed: Contracer contour measuring device, high-performance measuring system for automatic series measurement with motorized Z-column on granite plate. Straightness guidance of the X-axis via ceramic and automatic raising and lowering of the probe tip. Measuring range Z1 - axis = 60 mm. Table, screen and PC. The software can measure, evaluate and document. Machine dealer with own stock of 1600 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

- Z Axis 1100 mm - X Axis 1310 mm - C Axsi Endles - Working range stage 1: 4000 - 8500 mm - Working range stage 2: 4000 - 11.500 mm

- Closing force up to 18000 Kg - Opening force up to 15000 Kg - Driven table in & out feed - Upper table 270 Gr - Upper size 900 x 550 

- Pressure 0 - 250 Bar - T Size T-22 - Opening force 35 Ton - Closing force 150 Ton - Distance between column 2130 mm - Table height over floor 770 mm - Upper table rotation 180 Grad

- Table size 3500 x 2500 mm - Siemens Simatic OP7 controller - Max. work load 80 Ton - New price 1 Mil EUR - Working force up to 250 Bar - Power 30 kW

- Milling cutter lazer Guided - Working range 2000 - 8000 mm - Designed for Mobile use on gauge 3000 mm

- Bowl volume 120 liter - Out side diameter 910 mm - Width processing channel 210 mm - Overal channel length 1950 mm - Power 0.75 kW

Cap feeder for various types of caps, tubes, small bottles, etc. Stailess steel Year 2005

Punching force 45 t. 2 pcs. available from stock (Video under power on request)

Built in 1999 electric scissor pallet truck Load capacity 1,000 kg Lifting height approx. 80 cm Delivery date: immediately Price on request. We supply and install worldwide.

Manufacturer: MiSeq Model: Illumina Year of Manufacture: 2015 the device has performed 472 runs so far. Electrical Information - Line Voltage: 100V–240V - Frequency: 50/60Hz - Power Consumption: 400W Find more here - / Contact us at -

Air conditioner – "The ideal solution for climate control in proofers and prepared rooms." Features: - Energy-saving - Easy installation and operation - Device dimensions W x D x H: 425 mm x 205 mm x 1650 mm - Temperature and humidity adjustable - For fermentation rooms up to 12 m³ - Plug-in free-standing device Connection 400V, 16A-CEE plug New device with warranty + spare parts service

Deck Oven Miwe Condo C-3-1208 Miwe Condo Model: Type: CO.3.1208 Bottom heat and top heat can be controlled individually Chassis mobile with brake Connection 400V, 3 x 16A-CEE plugs Water connection 3/4 inch, water drain DN 40 Dimensions: 1500 x 1300 x 1950 mm, WxDxH Used oven

WITH TRIMMER p/n: 2654000N SN: 060900759 Format: up to SRA

• Output approx. 40 cycles/min. • 2 filling hoppers, manual product feeding • 2 vibrating pots • Robot Mitsubishi RH-3SDHR, max. load 3 kg • Vacuum gripper • Product transfer, e.g. into blister cavities of a blister machine, by inserting the product transfer area of a blister machine into the machine. • HMI programme control with touch screen • Drive 220V/50Hz This machine is offered at a special price and sold as-is without technical inspection.

Used manual batch ultrafiltration line for cottage cheese made by Agros Milko-Polska. Capacity: 2.500 kg of finished product in 8 hours, concentrated to 72% dry matter. New: 1996

206 Tons Midea Inverter Water Cooled Chiller - R134a a. Cooling Capacity : 206 RT b. Total Input KW : 119.1KW c. KW/Tons : 0.5774 d. Chilled Water In/Out : 12.0/7.0 Deg C e. Fluid Flow : 124.5 M3/hr f. Evaporator Pressure Drop : 75.3 KPA g. Condenser Water In/Out : 29.4/34.4 Deg C h. Water Flow : 144.5 M3/hr i. Condenser Pressure Drop : 60.2 KPA j. Starter : VFD k. Refrigerant : R134a l. Dimension (mm) : 3538 L X 1450 W X 2130 H Incoterm: EX WORK Currency: USD Commercial: Aaron Tan (yytantopglove.com.my)

MITUTOYO Crysta Apex CRT-A910 coordinate measuring machine was built in Japan by Mitutoyo Corporation. This extremely advanced machine, characterised by the highest accuracy and objectivity, is used for highly accurate workpiece measurements. Workpiece measurements are performed using the contact or non-contact method, which are then represented as a set of coordinate points. The use of this method makes it possible to measure parts with very complex shapes, which cannot be measured with ordinary measuring instruments. The MITUTOYO Crysta Apex CMM measuring machine is offered with a PC with software. Technical specifications of the MITUTOYO Crysta Apex CRT-A910 measuring machine - measuring range in the X/Y/Z axis: 900/1000/800 mm - measuring resolution: 0.1 µm - measuring speed: 300 mm/s - PC with software - compressed air pressure: 0.4 MPa - compressed air consumption: 50 l/m ...

- Double guideway two box way construction - Head changer for Multi-Face machining off larger compontents - ATC tool changer for Horizontal and vertical milling head swivabel - Distance table spindle nose    213 - 1093 mm - Distance table spindle center  130 -  ...mm - Indexing Horizontal head 5 Degrees x 72 positions - HeidenHain iTNC530 with HR410 handwheel - Spindle torq 1018 Nm ISO50  - Universal Huron type milling head

For sale here is the Bauer Mini - Verticus 3 300bar breathing air compressor with Bauer B-Kool refrigerant dryer and a storage tank 3 x 50l 300bar. 85 hours of operation. Comes from a research facility and is very rarely used.

Travel X/Y/Z: 800mm/550mm/550mm, tool holder: HSK63, spindle speed: 12000rpm, tool positions: 65, control: Siemens 840D, spindle hours: approx. 16000h. 3-axis robot System 3R Transformer WorkMaster, year of manufacture: 2008, transfer weight: 150kg, stroke: 1500mm, pallet positions: 2x12. Including System 3R GPS 240 zero-point clamping system, Knoll chip conveyor, Knoll paper band filter, Blum LaserControl laser measuring system, Renishaw 3D probe, and oil mist extraction. Documentation available. An on-site inspection is possible.

Agitator tank, make Schwarte - Milfor, year 2015, unused, for oil and other liquids,, stands on load cells,, Content: 1,000 liters, Inside diameter: 1,000 mm,, cyl. height: 1,250 mm,, outlet height: 500 mm,, single-walled/uninsulated on the top floor,, double-walled / insulated on the cylindrical shell and underbody,, with pressure-resistant heating/cooling system, Jacket space: 30 liters,, Permissible operating temperature: up to max. 85°C.