mh 800 e used for sale

THERMO SCIENTIFIC 8000 WJ CO2 Incubator / Oven Water Jacket Technology (WJ) Model 3429 Capacity: 184L CO² range: 0 to 20% CO² inlet pressure: 103.4 kPa. CO₂ sensor: CT Temperature range: +5°C UT to +50°C. HEPA filter inside. Glazed interior door. Aluminum control panel with digital display. 4 stainless steel shelves 1 container of water External dimensions HxWxD: 100x66x60cm. Interior dimensions HxWxD: 68.1 x 54.1 x 50.8 cm. 230V 50/60Hz. Net Weight: 120.2 kg Equipment tested at 37°C with a CO2 level of 5% In excellent working order and aesthetics Slight rust marks on the back of the outer shell (see photos) HEPA filters will need to be replaced The equipment will be delivered with the water jackets emptied. It is imperative to fill them in before you can use the equipment according to the manufacturer's recommendations Year of Manufacture: 2009

Used roasting/baking oven from Food Design Applications – Ireland Model: MSOG/2-100/800 Burners: Lanemark International Heating power: two burners: 2x 170kW = 340kW It is possible to connect steam. It can also work as a cooler, dehumidifier Two independent zones Electric blow height adjustment Electric blowing force adjustment Electric belt speed control Direct wash possible Indirect heat distribution system (tubular heat exchanger) Lower waste tray Stainless Tape, Braided with Belt Tensioning System Complete stainless steel chimneys, including exhaust gas control fans Natural gas Dimensions: Chamber (tunnel) height (adjustable) max. 250mm Tape width 950mm Belt width – working space 920mm Length of the whole machine 10250mm Baking Length 8000mm Machine width 2030mm Height with motors 3250mm Acid-resistant design.

LCD monitor with electronic for Cybelec DNC 800, 804, 806 control . only a few years in use. Supplier / Manufacturer : TSUBIS Germany , Art Nr: LCD10-0072

2015 Laem System VIS100-800 1. General Characteristics The VIS Machine is designed to correct alignment errors and remove defective spans from finished reels of APET sheets. The machine is bidirectional, allowing the web to run through the machine in either direction: during the first passage (from right to left), the web is checked by the operator and if necessary the defective spans are eliminated with the help of a splicing table. Once the reel has been cleaned and rewound, it can be unloaded, or if necessary, processed again (from left to right), especially if the material is printed. The splicing table is located in a comfortable ergonomic position, and it is designed to facilitate the splice (top and bottom) of rigid materials. 2. Web materials to be handled - The doctoring machine can unwind, process and rewind APET/PE materials The thickness range to be considered is 50 � ...

Cold wall plasma system this system has only been put into operation and has not been in use since then. It is used to activate surfaces or can also be used for nitriding processes. The equipment is as good as new and has never been in full production Usable space diameter 800mm Usable space height 1100mm Max. load 1500kg Operating hours only approx. 250h. Technical data: Usable volume DM 800mm H1100mm Max. load 1500kg Max. process temperature 580°C Pressure sensors manufacturer Pfeiffer - Model: CCR 373 Mass flow controller manufacturer Alicat (Ar, N2, CH4, H2) Vacuum pump manufacturer Pfeiffer Duo 65M Plasma generator specification Find more here - .ucymachines/ Contact us at - sales@ucymachines

The machine is in good technical condition, after prior agreement it is possible to test it. with the Siemens Shopturn system, including the feeder, the machine is fully equipped. BASIC PARAMETERS Working space max. turning Ø: ≈ 410–500 mm max. length: 800 mm distance between spindles: approx. 1020 mm swing diameter above the bed: ~700 mm realistic: ideal for shafts, flanges, bodies up to ~800 mm Travels (axes) X: ~480 mm Y: 100 mm Z: ~800–845 mm B axis: 110 (5-axis machining) C axis: 360 (indexing + interpolation) this makes it a full-fledged turn-mill (not a classic lathe) Spindles main spindle speed: ~5000 rpm power: ~25–34 kW passage: approx. 76–87 mm counter spindle speed: ~6000 rpm milling spindle (main difference compared to a classic lathe) speed: up to 12,000 – 20,000 rpm power: ~19–22 kW taper: HSK-A63 or Capto C6 allows: milling drilling tapping 5-axis simultane ...

PEDDINGHAUS Hydraulic 800 hydraulic punching machine was manufactured in Germany by Paul Ferdinand Peddinghaus GmbH. This highly reliable machine is used for the precision machining of angle bars and flat bars. It enables the punching of square and round holes in structural steel workpieces with a maximum thickness of 25 mm. The machining process is performed with a high press force of up to 80 tonnes by means of punches. The perfectly balanced design of the machine maintains excellent stability even during the most intensive challenges. All of this makes the PEDDINGHAUS Hydraulic 800 an excellent addition to industrial facilities and locksmith workshops. The total weight of the machine is approximately 1500 kg. Technical specifications of the PEDDINGHAUS Hydraulic 800 punching machine General data - maximum press force: 80 t (800 kN) - throat depth: approx. 200 mm - working heigh ...

Drawer cabinet, tool cabinet, steel cabinet, workshop cabinet, steel locker -Tool cabinet: Steel cabinet, 2 doors, solid construction -Width: 800 mm -Depth: 630 mm -Height: 1790 mm -Shelves: See photos for layout/height -Weight: 100 kg

Falch Pressure Washer R10/800, 1000 bar; only 2939 hours in use; complete with accessories as well as two rotary guns. Price basis for negotiation: 15.000,00€ net! If you have any questions, please call 0049 176 70044689 Mr. Becker Purchase and sale of scaffolding/formwork systems and construction machinery; Formwork restoration at fair conditions. Company SFS Meisterbetrieb Andreas Becker e. Kfm. Tel. 07305/9562350, Fax. 07305/9562352 mobile: 0049 176 70044689 Mr. Becker Office/ Storage Address: Birkenstraße 15 89185 Humlangen- Hüttisheim Ulm Registration Court: HRA722943 VAT ID NUMBER: DE279047055

Kitzinger Dishwasher Type Contino 800 Q BS3 REKU Year of Make: 2012 Noise exposure 85 dB (A) Output approx. 800 baskets/planks per hour possible Electr. Connected load: approx. 100 KW Washing temperature approx. 50°C Rinse temperature approx. 80°C Fresh water consumption: approx. 400 l/hour Tank volume approx. 1500 litres (pre-wash and main wash tank) Blow-off from 3 sides with 3 motors Max. throughput dimensions crates: 400mm high x 650mm wide Max. throughput dimensions of sheets/planks (portrait): 440mm high x 60mm wide Dimensions approx. LxWxH: 12,000mm x 2,200mm x 2,700mm Weight: approx. 1,500 kg - immediately available from STOCK

Müller-Dokument-Logistik-System, Inserting Machine – used - : Price from location: 39.500.-€ (net)! Manufacturer: Müller Type: 2016 Year of Make: 2016 6984F: Drive compartment incl. STOP 6978D Envelope Turner 8006C Inserting machine C5 / DIN long (approx. 6,000 cycles/h) 6628C/4 Multi-Channel System 6825C Folding machine (bottom-top) incl. STOP incl. stop on off 6822C-SCHALLSCH Soundproofing for Folding Machine 6822C-SCH-36583 Soundproofing for 6825C 6786D-L Collection Tray 6730C-L-STOP Transfer 6692D Sequencer 6784C-L Handover 6600D-12K Automatic Cutting Machine incl. Power Supply 6600BH Brush Holder 6875C Center Knife A4 tall, stacked, 2-up, pinfeed, face top / foot first always 2 sheets, Order Z-A Original price: over 100.000.-€ Condition: good Available: immediately Location: Lohne

Transnorm curved roller conveyor 180°-900-800 IR800 RA2233 Technical data: Manufacturer: Transnorm Type: TS 2712 curved 180° Built: 2001 Condition: good (used) Engine: fully functional Angle: 180° Inner radius RN: 800 mm (nominal radius) Outer width: 900 mm Clamping length: 800 mm Engine Type: SEW Gear Motor, R17DT71D4/TH Engine Power: V 380-500, kW 0.37 Drive: chain drive Conveyor speed: contact us Weight: 260 kg Scope of delivery: without supports Optionally available: Supports Lateral guide on one and both sides Frequency inverter for stepless speed change Length adjustment (longer/shorter) Other roller conveyors/roller curves with chain transmission Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg Features: Drive type: Chain overdrive Construction year: 2001 condition: good (used) Nominal / inner radius in mm: 800 Nominal / outside width in ...

The scope of delivery includes: 01x Wooden beams, used Species: Spruce / Fir Cross-section: approx. 200 x 100mm Total length: approx. 2,800 mm Weight | Pcs.: approx. 25.67 kg The price shown corresponds to the pick-up price for a wooden beam in the specified dimensions. Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is associated with additional costs, which will be charged separately depending on the delivery location or scope of delivery.

BT pallet lifter, max. lift 800 kg to up to 600mm. In very good condition, excellent quality steel from Sweden.

MBO foldering machine T 800, config.: 6-4, built 2004, format: max: 78 x 120; min: 15 x 25 cm with Piab air system , serial equipment, slitting shafts in all units and manuals. In very good condition technically as well as folding rollers. More photos on request. Navigator control unit MBO T 800.1-1-78/6- first folding unit 6 pockets auto adjustable MBO T 800.1-2-78/4- second unit 4 pockets manual adjustable Can ship worldwide.

MBO folder type T 800 6-4, built 2005. With PIAB air system, Navigator control, steel plate in feeder, serial equipment-slitting shafts and manuals. Configuration: 1. MBO T 800 1-1-78/6: folding unit 1 have 6 pockets that can be automatically adjusted 2. MBO T800 1-2-78/4: folding unit 2 have 4 pockets that are manually adjusted 3 MBO Stream delivery. TESTED. All rollers in very good condition. One auto pocket needs new servo motor. Available immediately. Can ship worldwide.

- max. open blacnk width 800 mm - straigh line - automatic crash lock bottom - gluing system with discs - machine in production

; Gross weight [kg]: 7200; Engine: Cummins QSK19-G11; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 1065

Automatic Transfer Switch - ATS Panel - ATI Panel, 800 Ampere - Applicable for generators up to 550 kVA; Gross weight [kg]: 110

Transnorm conveyor belt GF 22000-900-800 RA2186 Technical data: Conveyor length (NL): 22000 mm frame width (NB): 900 mm, 1000 mm with motor belt width (GuB): 800 mm Overall height (BH): 80 mm, 430 mm with motor Supporting feet: optionally available Conveying speed (v m/s): 0,5 Drive: SEW gear motor, R27 DRE80M4/MM15/LN Electrical data: 50Hz V380-500, kW 1,1 S1 Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Frequency converter for stepless speed change Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany Features: Construction year: 2014 condition: good (used) Conveying length in mm: 22000 Nominal / outside width in mm: 900 Belt width in mm: 800 Driven: YES Engine type: SEW Eurodrive Zentralantrieb mit Spannstation KW: 1,1/S1 Conveyor speed  ...

Ref.nr: 00911 Name of the system Vertical Inside Broaching Machine The electromechanically driven broaching machine is suitable for the precise and economical production of internal profiles, keyways and gears. Thanks to their robust construction, very smooth running and automated process sequences, it is ideally suited for use in series production. Manufacturer: Frömag Model Type FSR 6-800 MZB-PPC Year of construction 2008 Holder for three broaching needles Hub 800 mm aVersion: Vertical internal broaching machine Pulling force: 60 kN Connected load: 15 kW Control: FRÖMAG Commander PP-10 Broaching tools: 3 pieces Machine Dimensions (L x W x H): approx. 1,050 x 900 x 3,800 mm Condition Fully functional, currently dismantled, but if necessary this can also be demonstrated with the agreement of the seller Submission date Immediately

GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmTransverse stroke300 mmLongitudinal stroke850 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Spindle bore87 mmDiametre of spindle nose170h5 mmSpindle diametre on front bearing130 mmTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-6000 rpmPower max. (40% DC)10 kWMain drive 1Drive power (100% DC)25 kWTorque (100% DC)280 NmSpeed range25 - 5000 rpmAccuracy at point stopping0,01 degreeFloor space/WeightDimensions (L x W x H)3,99 x 2,69 x 1,99 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the application of an alternating speed for vibration sensitive s ...

GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmTransverse stroke300 mmLongitudinal stroke850 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWSpeed range25 - 5000 rpmTorque (100% DC)280 NmC-Axis Speed-200 rpmTorque of C-Axis (holding torque)225 NmAccuracy at point stopping0,01 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-4000 rpmPower max. (40% DC)11,3 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,69 x 1,99 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the  ...

GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmTransverse stroke300 mmLongitudinal stroke850 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose220h5 mmSpindle diametre on front bearing160 mmSpindle bore102 mmMain drive 1Drive power (100% DC)33 kWSpeed range20 - 4000 rpmTorque (100% DC)580 NmC-Axis Speed-200 rpmTorque of C-Axis (holding torque)580 NmAccuracy at point stopping0,01 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-6000 rpmPower max. (40% DC)10 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,69 x 1,99 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the a ...

GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmLongitudinal stroke850 mmTransverse stroke300 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle diametre on front bearing130 mmSpindle bore87 mmMain drive 1Drive power (100% DC)33 kWSpeed range20 - 4000 rpmTorque (100% DC)580 NmC-Axis Speed-200 rpmTorque of C-Axis (holding torque)225 NmAccuracy at point stopping0,01 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-4000 rpmPower max. (40% DC)11,3 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,69 x 1,99 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the  ...

GeneralCNC Turning Centre with C axis and tool drive; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways700 mmTurning diameter410 mmTransverse stroke300 mmLongitudinal stroke850 mmMax. Turning Length800 mmClamping chuck diameter max.315 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWSpeed range25 - 5000 rpmTorque (100% DC)280 NmC-Axis Speed-200 rpmTorque of C-Axis (holding torque)225 NmAccuracy at point stopping0,01 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-4000 rpmPower max. (40% DC)11,3 kWFloor space/WeightDimensions (L x W x H)4,46 x 1,88 x 2,30 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the  ...

01 set Picanol Air-Jet Weaving Looms, type OmniPlus 800 – 220-4R YOC 2010, working width 220 cm, 4 weft colors Stäubli electron. dobby 2881 – 16 shafts installed, Sumo motor, electron. take-up and warp let-off, max warp beam flange dia. 1,000 mm, off-loom take-up

pressure: 75 t stroke: 250 mm daylight longitudinal/sideways: 800 x 215 mm dayligth: 170 - 885 mm working pressure: 7,5 - 8.5 bar weight of the machine ca.: 0,45 t dimensions: 1,2 x 0,8 x 2,1 mm Hydraulic/pneumatic workshop press Cylinder can be moved sideways pneumatic foot pedal Winch for table height adjustment 2 pcs. pressing blocks CE marking The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Manufacturer: Jac Year of manufacture: 2023 Condition: , 1 year warranty( display unit) Cutting thickness: 4-30 mm Speed: 120-240 slices per minute Control: Touchscreen Knife: Teflon round knife for versatile bread types Knife drive: Planetary-geared knife Electrical: 230V / 1Ph / 0.75kW Dimensions (T x B x H): 380 x 340 x 160 mm

This 5-axis DN SOLUTIONS DVF 8000 was manufactured in 2022. It features impressive X-axis travel of 1,020 mm, Y-axis travel of 850 mm, and Z-axis travel of 805 mm. The machine includes a maximum workpiece diameter of 1,000 mm and a spindle speed of 18,000 rpm. If you are looking to get high-quality machining capabilities, consider the DN SOLUTIONS DVF 8000 universal machining centre we have for sale. Contact us for further details.

Vertical injection moulding machine manufactured in 1998. This Arburg 1200 TS 800-60-350 features a clamping force of 800 kN and includes two injection units: a vertical unit with a Ø22 mm screw and a horizontal unit with a Ø35 mm screw. If you are looking to get high-quality injection moulding capabilities, consider the Arburg 1200 TS 800-60-350 machine we have for sale. Contact us for further details.

This 3-axis SPINNER TC 800 110 MC was manufactured in 2009. It features a collet chuck for clamping and includes a dust extraction system. Optional equipment includes a bar feeder, parts catcher, turret with driven tool, chip conveyor, and tailstock. If you are looking to get high-quality turning capabilities, consider the SPINNER TC 800 110 MC horizontal turning machine we have for sale. Contact us for further details.

Metal Band Saw manufactured in 1993. This Friggi 2MF/AUT 800 x 800 2C features a cutting capacity of 800 x 800 mm and a round diameter of 800 mm. It is equipped with a powerful 7.4 kW saw blade motor and a hydraulic pump with a delivery rate of 58 L/min. If you are looking to get high-quality cutting capabilities, consider the Friggi 2MF/AUT 800 x 800 2C machine we have for sale. Contact us for further details.

This 3-axis Soraluce SM 8000 Bed Type Milling Machine was manufactured in 1999. It features an impressive X-axis travel of 6,250 mm, Y-axis travel of 1,200 mm, and Z-axis travel of 1,500 mm. The machine includes a spacious table dimension of 8,000 x 1,100 mm and a powerful 30 kW spindle. If you are looking to get high-quality milling capabilities, consider the Soraluce SM 8000 machine we have for sale. Contact us for further details.

A horizontal Malnati glass washing and drying machine is available. Nominal working width: 800mm, glass thickness range: 2mm-8mm, min. glass dimensions X/Y: 100mm/100mm, min. glass sheet spacing: 50mm, feed speed: 3.5m/min, washing brushes: 4. Machine dimensions X/Y/Z: approx. 2400mm/1350mm/1300mm, weight: approx. 1000kg. Documentation available. An on-site inspection is possible.

For sale 2 second-hand ALSTOM electrical transformers, in good general condition, from an industrial facility. Features: Brand: ALSTOM Power: 800 kVA Type: Three-phase transformer Frequency: 50 Hz Cooling: Oil (ONAN) Condition: Pre-owned Quantity Available: 2 units These transformers are ideally suited for industrial plants, MV/LV networks, production sites, logistics platforms, biogas plants or any project requiring a reliable power supply. ✔ Hardware available immediately. ✔ Visit possible by appointment. ✔ Loading on trucks possible. ✔ Transport in France and internationally on request. Price: Contact us. Do not hesitate to contact me for more information, additional photos or to arrange a visit.

New shredder Brand: REINBOLD Type: AZR 800 Special 22 kW The AZR series is known for its power. By means of the solid construction the machine also shredders bulky and bigger workpieces. Standard equipment: A row of round knives Ø40 mm with concave shape Turbo coupling Pusher Strenghed screen Switch cabinet with SPS control and 5 m cable Automatical switch-off function at empty container Safety package with gear box end switch and reverse counter Vibration damping machine feet GS-sign (dust tested) & CE-sign Technical data: Hopper opening: approx. 800 x 1200 mm Fill height: approx.1.610 mm Container volume: approx. 1,1 m³ Working width of the rotor: approx. 740 mm Rotor Ø: 354 mm Power main motor: 30 kW - 400 V - 50 Hz. - 3 Ph. Power hydraulical motor: 0,75 kW - 400 V - 50 Hz. - 3 Ph. Rotor speed: approx. 90 rpm. Number of blades: 20 pcs. round knives Kin ...

x-travel: 8000 mm y-travel: 2500 mm z-travel: 1000 mm control: Heidenhain TNC 355 taper ISO: 50 spindle speeds: 20 - 1800 mm voltage: 380 V total power requirement: 27,6 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Technical data Weingarten Mechanics Press 800 to Year of construction 1999 Nominal pressing force from 12.7 mm before UT 8000 kN Working stroke rate 10 - 40 strokes/min Setup stroke number 5 - 15 stroke/min Plunger stroke 200 mm Maximum tool installation height 1200 mm Stroke at the bottom, adjustment at the top Minimum tool installation height 900 mm Plunger adjustability 300 mm Standard tool installation height (closed tool if power setup springs are present) 980 mm Table top dimensions, length x width 3600 mm x 230 mm Plunger plates dimensions, length x width 3600 mm x 23 Passage between the uprights in length 3600 Passage between the uprights in width 2300 Standard infeed height above press table 750 mm Inlet height adjustment range 620 - 800 mm Quick Tension Plunger Plate: Hollow piston cylinder, variable 4 pcs. on each side Too ...

This 5-axis Okuma LB 3000 EX MYW 800 was manufactured in 2011. It features a maximum turning diameter of 410 mm and a distance between centers of 1,020 mm. The machine includes a robust tool turret with 12 positions and a maximum spindle speed of 4,200 rpm. If you are looking to get high-quality turning capabilities, consider the Okuma LB 3000 EX MYW 800 horizontal turning machine we have for sale. Contact us for further details.

description: 180 ° curve conveyor suitable for different tray formats. Belt width 800 mm Radius 1800 mm New-quality motor can be offered with the desired requirements width: 4450 mm length: 2500 mm serial number: 642-92-900 S176 Besides buying and selling of conveyors and machines our strength lies particularly in services and project planning, as for example in rebuilding and adapting of your installation as well as in overhaul and relocation of machines. You have a first idea or even a concrete plan? It does not matter how far your project is, we support you in every phase! Or do you want to sell or market your machine? We also buy machines or provide you with a marketing concept. Ask for your individual offer or visit us in Knetzgau. Concerning bigger projects we can of course also visit you in your company to do an on-site survey. Our DRINK techni ...

Workbench, work table, assembly bench, assembly table, worktable, wooden workbench table, aluminum workbench table -Workbench: Workbench table with drawers / solid construction, height adjustable -Width: 2000 mm -Depth: 800 mm -Height: 760 mm, adjustable, see photos -Weight: 74 kg

Workbench, work table, assembly bench, assembly table, work table, base -Base frame: Work table tubular frame frame with mounting plates for swivel casters -Width: 1200 mm -Depth: 800 mm -Height: 720 mm -Quantity: 1x workbench available -Weight: 29 kg

GeneralVertical Machining Centres; Control: DMG MORI SLIMline® Multi-Touch control CharacteristicsMaximum load (table centre)800 KgDimensions (L x W x H)3,3 x 2,7 x 2,94 mRapid feed X / Y / Z30/30/30 m/minMovement X / Y / Z800/560/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with30 PositionsMax. torque83 NmTorque (100% DC)57 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWSpeed max.12000 rpmTable surface1100 x 560 mmWeight approx.5550 KgDirect measuring system X,Y,ZDirect Measuring System X, Y, Z inclusive Air Purge for Measuring SysteminlineMASTER® spindle 12.000 rpminlineMASTER® spindle 12.000 rpm Spindle speed range 20 to 12.000 rpm Tool Taper SK40 DIN69871 with BIG PLUS inteface Tool clamping according to DIN69872 Power: 13kW (40% DC) / 9kW (100% DC) Torque: 83 Nm (40% DC) / 57 Nm (100% DC) bearings oil-air lubrSK40 interfaceTool clamping SK 40 for pull-studs DIN 69872NC-D ...

max. format 78 x 115 cm Year of construction 2002 MC Control Counting device MCC 3 Round stack feeder Dual feed 6 fold pockets in the parallel fold section Downstream knife shaft Window rebate bag Vertical stack delivery Delivery date: immediately Price on request. We supply and install worldwide.