mez cz used for sale

MADE BY KAESER TYPE AIRCENTER SK22T S/N 2324 YEAR 2012 POWER (kW) 11 SPEND. (m3/min) 1.85 PRESSURE (bar) 8 INVERTER no WBUD. DEHUMIDIFIER yes EXCHANGER no COOLED (POW/WATER) air ON THE TANK yes 350 L

PROD. ALUP TYPE ALLEGRO110 S/N API178778 YEAR 2020 POWER (kW) 110 kw PUMP. (m3/min) 3.6-19.06 (7.0 bar) 3.72-18.3 (8.0 bar) 3.90-17.16 (9.5 bar) PRESSURE (bar) 10 HR (DOC/GENERAL) 22871 INVERTER YES

PROD. ATLASCOPCO TYPE GA30 S/N API324380 YEAR 2013 POWER (kW) 30 PUMP (m3/min) 5.18 CIS (bar) 8.5

– after technical inspection – made in Poland –DTR TECHNICAL PARAMETERS: Log diameter max. 300 mm log length 500 - 3000 mm motor power 2 x 7.5 kW head spacing manual Feed infinitely adjustable on the inverter wheel diameter 600 mm length of belts 4004 mm Unhooking lines feeder height from the base 810 mm dimensions of the machine (length/width/height): 530 / 200 / 195 cm weight ~ 1200 kg

Used filling tank with capacity of 250 kg by SPOMASZ PLESZEW type CZA7a. New 1999. New, unused, control cabinet. Weight 350 kg. 3 pieces available.

PROD. KAESER TYPE CSD85 SFC S/N 1076 YEAR 2014 POWER (kW) 45 EFFICIENCY (m3/min) 1.99-8.37 CIS (bar) 8.5 HOURS (DOC/OC) FEEDER yes BUILT. DRYER no EXCHANGER yes

PROD. ATLASCOPCO TYP GA90 S/N AIF047037 ROK 1998 MOC (kW) 90 WYDAJ. (m3/min) 14,5 CIS (bar) 7,5

Hydraulic power pack with gate valve ORSTA pump: 10/16-1 TGL 10885 p: 16 Mpa (160 bar) V: 10 cm3/U Engine: MEZ 1AP100L-6 1,5 kW 935 rpm 220 / 380 V 3AC tank: approx. 75 l used, tested ! Dimensions: 920 x 430 x 930 mm

Hydraulic power pack with tank, universal power pack ORSTA 6.3/16 - 40.0/3-0 ( 6.3/16-40.0/3-0 ) TGL 10897 16 MPa ( 160 bar ) 6,3 dm3/min ( 6.3 l/min ) Engine: MEZ 1AP100L-4S 2,2 kW 1430 rpm 220 / 380 V 3AC Tank: approx. 40 l New ! Dimensions: 750 x 380 x 690 mm

Three-phase electric motor, with pump frame MEZ MOHELNICE Type: 4AP90L-4 1,5 kW 1410 rpm 220 / 380 V 3AC 50 Hz Design: B3 IP54 Shaft diameter: Ø 24 mm Wavelength: 50 mm Groove width: 8 mm motor base: 145 x 168 mm hole spacing (parallel to shaft): 125 mm hole spacing ( transverse to shaft ): 140 mm Mounting screws: 4x M8 x 1,25 with pump frame: APOLLO Type: G 199967 pump base: 170 x 180 mm hole spacing (parallel to shaft): 85 mm hole spacing ( transverse to shaft ): 115 mm Mounting screws: 4x M10 x 1.5 New ! Dimensions: 640 x 210 x 245 mm

coolant filter system, coolant system, filter system MZ, FILTER TECHNOLOGY WEIDA EMA 200 coolant tank: 1290 x 610 x 350 mm ( approx. 250 l ) magnetic roller: Ø 130 mm x 450 mm speed: 440 rpm engine: MS562-4 0,0,09 kW 1320 rpm 220 / 380 V 3AC K&S PG056 Gear ratio: 3 coolant pump1: Engine: MEZ BRNO 4AP71-2S 0,37 kW 2800 rpm 220 / 380 V 3AC coolant pump2: Motor: IMB14-71x0,37x3000 0,37 kW 2850 rpm 220 / 380 V 3AC used, tested ! Dimensions: 1210 x 600 x 510 mm

Three-phase electric motor MEZ MOHELNICE Type: 4AP90S-6 0,75 kW 940 rpm 220 / 380 V 3AC 50 Hz Type: B14K IP54 Shaft diameter: Ø 24 mm Wavelength: 50 mm Groove width: 8 mm Flange diameter: Ø 95 / 140 mm bolt circle diameter: Ø 115 mm 4x threaded hole: M8 x 1.25, depth: 20 mm used, tested ! Dimensions: 290 x 170 x 210 mm

Three-phase electric motor MEZ MOHELNICE Type: 2AP63-4 0,0,18 kW 1350 rpm 220 / 380 V 3AC 50 Hz Design: B5 IP44 Shaft diameter: Ø 11 mm Shaft length: 22 mm Groove width: 4 mm Flange diameter: Ø 95 / 140 mm bolt circle diameter: Ø 115 mm 4x bore: Ø 9.5 mm New ! Dimensions: 185 x 140 x 175 mm

Three-phase electric motor MEZ MOHELNICE Type: 4AP80-2S 0,75 kW 2840 rpm 220 / 380 V 3AC 50 Hz Design: B14K IP44 Shaft diameter: Ø 19 mm Wavelength: 40 mm Groove width: 6 mm Flange diameter: Ø 80 / 125 mm bolt circle diameter: Ø 100 mm 4x threaded hole: M6 x 1.0, depth: 10 mm used, tested ! Dimensions: 265 x 155 x 195 mm

Centrifugal pump, water pump APOLLO 4 KSEY-25-002 Q: 1,6 m3/h H: 63,00 m Engine: MEZ 4AP90L-4 1,5 kW 1410 rpm 220 / 380 V 3AC IP54 used, tested ! Dimensions: 750 x 210 x 320 mm

Centrifugal pump, water pump, APOLLO 4 KSEY-25-002 02-008-85-017 Q = 1,6 m3/h H = 63.5 m Engine: MEZ 4AP90L-4 1.5 kW 1410 rpm 220 / 380 V IP54 used, tested ! Dimensions 800 x 240 x 360 mm

Gear pump, feed pump with motor ORSTA BÜG 4 / 4 Qmax: 4 m3/h ( approx. 66,7 l/min ) pmax: 0.4 MPa ( 4.0 bar ) pump: BÜ4,0 / 10 Engine: MEZ Type AP90L-4 1,5 kW 1410 rpm 220 / 380 V 3AC IP54 used, tested ! Dimensions: 590 x 250 x 2830 mm

Centrifugal fan, dust extractor fan, fan, extractor, dust fan, blower -Manufacturer: Kiekens, dust extractor type QTE-280 -Motor: MEZ 4 kW 2920 rpm -Fan wheel: Ø 490 mm -Connection: inlet Ø 280 mm -Connection: outlet Ø 310 mm -Dimensions: 730/610 / H1000 mm -Weight: 99 kg

Drill press, bench drill, column drill, pillar drill -Manufacturer: TOS, high-performance column drilling machine type 40 TF / C -Motor: MEZ 2.2 kW -Speeds: 56 - 2240 rpm -Table size: 400 x 315 mm, travel 600 mm -spindle taper: MK4 -Spindle stroke: 165 mm -Projection: 290 mm -Pillar Ø: 140 mm -Dimensions: 1200/650 / H1990 mm -Weight: 602 kg

coolant filter system, coolant system, filter system SOMMERMEYER SB20 coolant tank: 1200 x 500 x 200 mm ( 120 l ) coolant pump: MEZ BRNO 3COA2-22 0,42 l/ sec ( 25,2 l/min ) engine 0,09 kW 220 - 254 / 380 - 440 V 3AC used, tested ! Dimensions: 1210 x 600 x 510 mm

Chip Conveyor, Hinge Plate Conveyor- Chip Conveyor, Hinge Belt Conveyor SILISTRA TCA 280 x 3221 Inlet: 3210 x 280 mm Free belt width: 280 mm Height inlet: 400 mm Height discharge: 950 mm Motor: 0,,55 kW 220 / 380 V 3AC coolant reservoir: 4450 x 550 x 230 mm coolant pump: APOLLO 4 KSEY-25-002 02-008-85-017 Q = 1,6 m3/h H = 63.5 m Engine: MEZ 4AP90L-4 1.5 kW 1410 rpm 220 / 380 V IP54 used ! Dimensions: 5000 x 1050 x 1250 mm

Hall extraction system, chip filter system, filter system, chip extraction, wood chip extraction, Centrifugal fan, chip extraction fan, fan, suction, chip fan -unfortunately no funding data available -Motor: MEZ type 4AP80-2 -Motor power: 1.1 kW -Speed: 2840 rpm -Connection input: Ø 60 mm -Outlet connection: Ø 400 mm -Base: on castors -Dimensions: 940/540/H1510 mm -Weight: 74kg

We sell a Czwaluk lift truck here. This lifting tipper was designed and built by us. The frame is made entirely of stainless steel has a maximum load of 600kg, a tipping height of 2800mm with a tilting angle of 45., This lifting tipper can be manufactured for you according to your wishes. Whether tipping height or boiler fork , anything possible.

Make SKODA type SUA 125 PA built 1992 place of storage from location country of origin Czech Republic delivery time immediately freight base from location Technical details: turning diameter over bed 1500 mm Turning diameter over support 1100 mm turning length 13000 mm Control SIEMENS 820 T plan disc speed range 0.9 - 315 r pmWork unit weight between tips max. 14000 kg Main drive DC 42 kW Total power requirement 65 kW Machine weight approx. t space requirement approx. m Additional information - CNC control SIEMENS 820 T - increased turning diameter 1500 mm - positioning of the flat disc via M-function or manually in typing mode with digital display - other accessories: + belt grinding device + 2 bezels max. 630mm and 4.8t load capacity + 2 roller blocks max. 950 mm and 7t load-bearing capacity - Hydrostatic main spindle bearing

[ 5000 characters max., no information about the advertiser ] Brand:MODUL Model:ZFWZ 2000/3 Type:Gear Hobbers Year:1981 Location:Czech Republic Specification: Max diameter of gear without tailstock 2100 mm Max diameter of gear with tailstock 1450 mm Max face of gear 1060mm Max module with hobbing head 22 Max/ Min center distance 1240/150 mm Min number of teeth 10 Max pressure angel 45 deg Table dia / number of slots 1800 mm/12 Bore in table / length 600/800 mm Max dia of hob / length 300/330 mm Max weight of workpiece 15000 kg Accessories: Standard milling head Tailstock (no clamping) Set of gear supports (shoes) Set of arbors Set of change gears

Westphal Mechanics C7x Commutator Slot Center Machine No. M64127 Year of construction: 09/2019 The commutator slot center has four processing steps. In the steps, the following components are approached: Contact slot saw Insulating groove saw Deburrs Brush The Stäubli TS 80 Robotor with SP1 control has two grippers that transmit the commutator to the individual stations. Software data: Marking Builder2 (2D) Marking Builder2 (3D) Logo designer Power supply: 3/N/PE AC 400/230 V 50 Hz Control voltage: 24 VDC More information via this link. Further technical data will follow shortly. The roller straightening unit is located in Hildesheim and can be dismantled and picked up there by the customer. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves,  ...

Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßer CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßerb CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

The profile perforating machine INTESO S3130T was manufactured in 2011 in the Czech Republic. Technical parameters: - Maximum internal diameter of the sheet metal coil: 80 mm - Maximum length of the finished product: 3000 mm Technical data : - screen control panel: SIEMENS - maximum length of profiles: 3000 mm - maximum cross-section of perforated profiles: 120 x 80 mm; fi 80 mm - automatic linear feed - optical sensor for automatic control of the correct length of the part - linear positioning of the hydraulic cylinder stroke - non-deformation perforation technology - the possibility of perforating profiles of various shapes - memory of perforation programs - two-sided perforation (in one operation) and one-sided perforation - automatic lubrication - maximum pressure of the hydraulic press in the line: 147 kN (15 tons) Tool accessories for the INTESO S3130 T punchin ...

SincoTec POWER SWING MAG Electromagnetic Resonance Test Bench The POWER SWING MAG is the ideal testing machine for material testing and component testing with low backp and low damping. Due to the resonance principle, the POWER SWING MAG is very energy-efficient, fast and highly accurate. Properties: -High frequencies -Automatic crack detection -Energy efficient -Short test times max force 5 kN displacement 4 mm Frequen range 40..300 Hz Weight 1.5 tons Year of construction 2011 Original price approx. 100.000 € Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

Hinst continuous cleaning system Continuous washing systems from the manufacturer Hinst are designed to treat series parts in large quantities with the highest purity requirements at the same time. Appendices No. 04.333 Year of construction 12.2004 Dimensions approx. WxDxH: 3.80 x 4.30 x 3.80m Incl. - 6 baskets: Basket dimensions: 48,5x48,5x H26cm - Roller conveyor 2,10x52x90cm The continuous cleaning system has already been professionally dismantled and stored with a value of € 3,500 these are included in the purchase price. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

Discus Werke DSH 600/1000 Side Surface Grinding Machine This type of machine is a machine with a motor-driven grinding spindle. The clamping and grinding of the workpieces is carried out with clamping devices tailored to the respective work. The devices are attached to the machine bed. The column saddle on which the motor spindle is mounted serves as a feed, dressing and pendulum slide. Manufacturer: Diskus Werke Model: DSH 600/1000 Serial number: 6299 Type: Side Surface Grinding Machine Cooling lubricant: Isocool 1020 BF Coolant volume: 400 liters Concentration: 2.5% (x factor 1.6 ≙ 4%) Year of construction: 1964 Condition: used The side surface grinding machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure,  ...

White temperature test chamber WT 11-18 KWP 500/40 Spring, summer, autumn and winter - your products must be able to withstand different temperatures during manufacture, transport, storage and use. The temperature test chambers from Weiss Technik help you to test the influence of thermal conditions on the properties, function and service life of your products. Manufacturer: Weiss Technik Type: KWP 500/40 - 180 DU Designation: WT 11-18 Type: Temperature test chamber Test room volume: 500 ltr. Temperature range: -40°C to +180°C External dimensions: 110 cm wide, 173 cm deep and 204 cm high Internal dimensions: 80 cm wide, 85 cm deep and 85 cm high Pressure: 25 bar Voltage: 380 V Frequency: 50 Hz kVA: 4.7 Refrigerant: R 502 Year of construction: 1990 Condition: used Complete plant closure, large selection of mezzanine, pallet racks, shelve ...

TURNING ROLLERS LAMBERT JOUTY CZ100 max load capacity 100 tons auto alignment good conditions, ready to work!

Material test bench / final inspection consisting of the following main components Keyence XG-H500M Digital 5 Million Pixel P/W Camera CCD: 2/3-inch monochrome CCD, squareElement all pixels 11 times read speed, 5,050,000 pixels Scan Method: Progressive (61.2 ms), Interlace (40.3 ms)Interlace is a binning process that sums up the odd rows and even lines. Model CA-DC21E Lighting Controller Type lighting controller For XG/CV-5000/CV-X200/CV-X100 series only Input: Forced shutdown of the lighting: Input voltage max. 26.4 V, min. 2 mA Edition Light control method (1) Constant voltage regulation method (DC lighting) (2) Pulse width modulation method (emission frequency: 100 kHz) [Change of ECU setting] Brightness levels 255 levels digital [Change of ECU setting] Number of connections 2 channels (available for LED connection and terminal block connection) Voltage 12 VDC ...

Fanuc LR Mate 100i High Speed Robot with Control It is a five-axis, modular, electrically servo-driven robot designed for loading and unloading precision machines, welding and material transport. Its hollow joint construction encloses the entire cable routing to avoid getting stuck. The FANUC LR Mate 100i also features brushless AC servo motors that minimize motor maintenance, sealed bearings and drives enable operation in harsh factory environments. Included in delivery is the control unit Mate RJ-2 Robot Specifications Axles: 5 Payload: 3kg H-reach: 620 mm Repeatability: ±0.04 mm Robot mass:32kg Movement speed of the robot J1 180 °/s (3.14 rad/s) J2 180 °/s (3.14 rad/s) J3 225 °/s (3.93 rad/s) J4 216 °/s (3.77 rad/s) J5272 °/s (4.75 rad/s) Robot Motion Range Robot J1 ±160° J2 +150° - 35° J3 +206° - 159° J4 ±120° J5 ±200° (Changes and e ...

Conveyor technology, Knapp, approx. 1.484m, roll width approx. 42cm, ideal for boxes or cartons in 40 x 60cm - used - : Price ex location: only 99.500.-€ (net), dismantled, packed and loaded! Manufacturer: scarce Year of construction: 2017 Element width: approx. 51cm Roll width: approx. 43cm Mainly rollers, but there are also a few climbing bands etc. With various converters, curves, 1 scale, roller strips, Stowage Weight: max. 25kg For an extra charge, carton erectors, carton cappers, carton wrappers, inserts for advertising, etc. are also available for sale. On request, continuous shelves are also available for sale (for an extra charge)! Condition: good Available: from about March 2022 Location: Czech Republic Plan on request!

Numer katalogowy 6349 DANE TECHNICZNE - max szerokość obrabianego elementu 250mm - max wysokość obrabianego elementu 110mm 2 agregaty szlifujące: górny i dolny z góry: - 2 rolki dociskowe poślizgowe - agregat szlifujący 2 walce metalowe + trzewik - rolka dociskowa poślizgowa - taśma gumowa ciągnąca – VACUM z dołu: - taśma ciągnąca - 2 rolki poślizgowe, metalowe - agregat szlifujący 2 walce metalowe + trzewik - 3 rolki wyprowadzające ciągnące, metalowe - czyszczenie papieru przy agregacie górnym i dolnym - elektrycznie ustawiana wysokości szlifowania - oscylacja taśm szlifujących - płynna regulacja prędkości posuwu na falowniku - silniki główne 2×5,5kW - zapotrzebowanie powietrza 8bar - średnica króćców odciągu 4x100mm - wymiary całkowite dł/szer/wys 1400x1200x1850/2250mm - waga 1490kg – do krótkich ele ...

1500 m² mezzanine Schäfer R3000 3-storey Used goods, top condition, as good as new, see pictures Ground floor mezzanine steel construction, above 2 floor shelf system Schäfer Manufacturer SCHÄFER R3000 CAD planning and assembly 3-storey Partial sale possible Negotiation price: on request! Goods are in stock. Transport and assembly possible on request. Viewing possible at any time by appointment. Further information on request. Constantly over 5000 lfm pallet racks from numerous manufacturers in stock. (Changes and errors in the technical data, information and prices as well as prior sale reserved! See our terms and conditions, all prices excl. VAT ex stock) Purchase / Sale We are constantly looking for or offering numerous articles from a wide variety of areas swept-clean company clearances Operational resolutions Fast- flexible - quick ...

4,000 m² Nedcon mezzanine Column grid 800 cm x 600 cm! Used goods, top condition, as good as new, see pictures Height of the upper edge of the stage 370 cm Load 500 kg/m² Flooring different finishes available. Cargo lifts, stairs, railings and accessories sufficiently available CAD planning and assembly possible Partial sale possible Negotiation price: on request! Goods are in stock. Transport and assembly possible on request. Viewing possible at any time by appointment. Further information on request. Constantly over 5000 lfm pallet racks from numerous manufacturers in stock. (Changes and errors in the technical data, information and prices as well as prior sale reserved! See our terms and conditions, all prices excl. VAT ex stock) Purchase / Sale We are constantly looking for or offering numerous articles from a wide variety of areas swept-c ...

1,500 m² Nedcon mezzanine Column grid 800 cm x 600 cm! Used goods, top condition, as good as new, see pictures Height of the upper edge of the stage 370 cm Load 500 kg/m² Flooring different finishes available. Cargo lifts, stairs, railings and accessories sufficiently available CAD planning and assembly possible Partial sale possible Negotiation price: on request! Goods are in stock. Transport and assembly possible on request. Viewing possible at any time by appointment. Further information on request. Constantly over 5000 lfm pallet racks from numerous manufacturers in stock. (Changes and errors in the technical data, information and prices as well as prior sale reserved! See our terms and conditions, all prices excl. VAT ex stock) Purchase / Sale We are constantly looking for or offering numerous articles from a wide variety of areas swept-c ...

Compact machine system for the production of stamped and bent parts made of strip and wire. Tool quick clamping system for shortest set-up times User-friendly machine and process control P CNC 4E Compatibility with RM 35, RM40 and RM4 tools Item condition: very good You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

Compact machine system for the production of stamped and bent parts made of strip and wire. Tool quick clamping system for shortest set-up times User-friendly machine and process control P CNC 4E Compatibility with RM 35, RM40 and RM4 tools Item condition: very good You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

Compact machine system for the production of stamped and bent parts made of strip and wire. Tool quick clamping system User-friendly machine and process control P CNC 4E Compatibility with RM 35, RM40 and RM4 tools Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

Bihler RM 30 E punch bending machine Bihler RM 30 E punch bending machine for the production of stamped and bent parts made of strip and wire. Compact machine system for the production of precision stamped bent parts User-friendly machine and process control Bihler P CNC 400 Compatibility with RM 35, RM40 and RM4 tools Year of construction 2003 Machine housing and perforated plate Specifications Machine power: 5 - 400 strokes/min Feed length: max. 240 mm Backing edge of the strip: max. 80 mm in front of perforated plate Strip bottom edge: 4 mm above center machine Material dimensions: strip width max. 60 mm, wire Ø max. 4 m Material feeder right (176-05-00195.0) 240 mm feed length Specifications Material trailing edge: 80 mm in front of perforated plate Material bottom edge: 4 mm above center machine Material width: max. 60 mm Feed length: max. 240 mm  ...

Thumm SU100 P Current UV Immersion Impregnation System with Exhaust Air Purification System Current UV impregnation is an innovative immersion process for low-voltage round wire windings. In this process, a low DC voltage is applied to the winding and the required process heat is generated very effectively by current flow. When dipping the heated winding, the impregnating agent becomes thin and can thus penetrate into the smallest cavities. With continuous heating, the impregnating resin gels on the hot conductors of the winding, whereby the resin can drain off again after immersing on the cooler sheet metal package. The winding is heated and dried by means of electricity. UV lamps cure the light-sensitive resin on the sheet metal package. By eliminating conventional furnace drying, energy and time are saved. Together with the use of a low-emission impregnating agent, the en ...

Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßer CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

ORDER NO. 6524 TECHNICAL DATA - track width 360mm - shaft width 350mm - max disc diameter 350mm - disc bore diameter 80mm - max cutting height 120mm - table top size 2040x840mm in advance: - ratchets - pulling shaft, toothed - ratchets - smooth sliding shaft - shaft with saws - slip shaft, pressure shaft bottom: - 2 rolls in front of the table top - guide - ratchets - caterpillar - central lubrication of the track - electric shaft lifting with saws 0.55kW - electric body lifting 0,55kW - smooth regulation of the feed speed - diameter of the extraction connection 140,125mm - main motor 45kW - overall dimensions L/W/H 3530x2220x2200mm - weight about 4000kg ADVANTAGES – Czech production – 2 slip rollers in the countertop – used multisaw – very good condition Net price: 62900 PLN Net price: 13978 EUR depending on the price 4,50 EUR  ...

Schroeder & Bauer WB 32-1 Universal wire and belt bending machine Wire feed Plain text display Press force monitoring Wire straightener Bosch stripping devices Bracket and brush motor with mounted tool W32/1-32 Soundproof cabin Fäßerb CU wire with stamped parts Switchboard Item condition: very good Description of the manufacturer, deviations possible. You purchase the machine as it can be seen in the pictures. The punch bending machine is located in Hildesheim and can be dismantled and picked up by the customer there. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

ORDER NO. 6591 TECHNICAL DATA - track width 450mm - shaft width 450mm - disc bore diameter 80mm - shaft diameter 60mm - min dial diameter 300mm - max dial diameter 400mm - max cutting height 250mm - max width of input material 860mm - min length of the workpiece 800mm in advance: - repellers - pulling shaft, metal pressed pneumatically - repellers - pulling shaft, metal, pneumatically pressed - pressure - shaft with saws - pressure - 2 pulling shafts, metal pressed pneumatically bottom: - metal roller, slip roller - guide - repellers - caterpillar - shaft with saws - caterpillar - smooth adjustment of the feed speed on the inverter 4-40m/min - main motors 2x75kW - feed motor about 3kW - electric body lift up/down 0.55kW - electric shaft adjustment with saws 2×0.18kW - central lubrication - diameter of the extraction connection 2x300mm  ...