manual book used for sale

1 x Smit 660mm dia x 2100mm wide two roll mill, Rebuilt 2005, manual nip adjustment, Lunn type safety bars, Back roll surface fluted, Front roll smooth finish. Bush type bearings with flood lubrication, compact \Jahnel\ right angle drive gearbox. with 180KW DC variable speed motor and controls. Strip knives to front roll. Heavy duty 2 part bedplate. Extra Information: Front roll 29 teeth Back (fluted roll) 32 teeth Friction ratio 1:1.1 Motor 180kW DC variable speed, 1300rpm, Gear box ratio 1:9.8 Bullgear 122 teeth, Pinion gear 18 teeth (Ratio 1:6.777) Therefore approx roll speeds as follows: Input motor speed 1300rpm: Front roll 21.53 rpm Back (fluted) roll 19.6 rpm

Kobelco Twin Screw Roller Head Extruder (horizontal type), Model TSR-330 Roller die assembly (TSR-33H005H) 38in wide x 16in dia Roller die moves away from the extruder/mixer section via hydraulic ram. driven by 102kW DC variable speed motor through Hansen reduction gearbox (on flexible coupling so roller die can move forwards/back). Twin screw dump extruder 330mm screw dia driven by 90kW DC variable speed motor through Hanson reduction gearbox. In very good condition. Previously running underneath an F270 Banbury. Complete with all controls, manuals and documentation etc.

Nakata Zoki Kobe, Japan (Troester design) Duplex Extruder Unit Dual 150mm dia PIN Type Extruders, Year of manufacture: 1990, with Roller Feed, and duplex Die. L/D ratio 16:1 Number of Pins: 10 Rows x 8 Pieces, Spare Pins included. Screw Speed 45 r.p.m. Motors 185kw D.C. variable speed, 415 volt, 3ph, 50hz. Full Books and Drawings available. Thyristor Drives included. Starter and Control Panel for Lower Extruder only. Die usable Width 18\\, In good condition.

Cat.-Nr. 11-3210 new Basic Equipment The Brew House is complete with all equipment. All equipment are with high standard an very simple to use. This 10 hl Brew House is built as 2 devices-brew house manual version with manual butterfly valve. It is possible to make 2 brews/day (40 hl) Technology All the pipes can be cleaned and sterilized in the circuit over the pump included. a) In the mash boiler the mash will be cooked, then it will be pumped with one beer pump made of stainless steel from mash boiler to the lauter tun. b) After the lauter wort will be pumped back to the mash boiler. c) After emptying the lauter tun the grit floor will be removed. The lauter tun will be changed to a whirlpool. d) After cooking the hops a special injection valve is introduced inside the lauter tun so that it can be used as a whirlpool. Mashing Tun / Wort Boiler Volume brutto: ...

Cat. No. 11-3210 New Plant description Sudwerk This small-sud plant comprises all components for a complete and fully functional brewing plant. All system parts used have a high quality standard and are characterized by their ease of use. The two-device brewhouse consists of a mash/spice pan and a purified vat, which is also used as a hot tub. Technical description All pipes are cleaned by a circulation pumping system. a) In the mash pan, the mash is boiled, then the mash is pumped with the beer pump into the purifier pond. b) When bluish, the wort is pumped back into the mash pan. c) After bluish, the purified vat is cleaned and the sieve bottom removed. A special injection nozzle is installed on the cylinder wall at the bottom of the läuterbottich. As a result, it can also be used as a hot tub after removing the mobile screen floor. d) After boiling the hops  ...

Collin Two Roll Lab Mill, Roll size: 150mm dia x 400mm wide Hydraulic nip adjustment, Model: WALZWERKE 150, Year of manufacture: 1988, Power: 19kW Electric roll heating with oil - operating temp 50 to 220 C Each roll variable speed from 0 -30 rpm Manual lubrication, programable controls. In very good condition. Manuals/drawings available.

Gaulin MC15-5TPS homogeniser, 3850 l/u, 350 bar. 2 stage, manual operated homogenising valves, Fully overhauled, as new condition.

1 of used tray-/padshrinkpacker, make KHS Kisters, type Innopack TSP 80 V with 180-degree (clockwise) curve and shrinktunnel, new 2004. Machine has an 8-lane infeed and is capable of producing trays (and/or) pads either single lane (i.e. 24 cans/bottles per tray/pad) or dual-lane (i.e. 12 cans/bottles per tray/pad) in shrinkwrap film (print-registered), at a maximum capacity of 80 cycles (i.e. 80/160 trays) per minute. Operating direction: from right to left as seen from operator\s station. With Allen Bradley Control Logix PLC / Panel View 1000, Indramat servo drives, ITW Quattro hot-melt unit. Both packer and shrinktunnel easily adjustable via servo\s and spindles for various formats as well as single-/dual-lane. Wired for 480V/60Hz. Various manuals available. Equipment in excellent condition!

1 x Bridge 84in x 26in/22in dia two roll mill, manual nip adjustment, Cored rolls with rotary joints fitted, Bronze bush type sleeve bearings, with Hagglunds hydraulic drives fitted to each roll, 160kW motor with pump to each roll for variable roll speed/friction. Drives fitted in 1988 (Marathon type). Complete with controls etc and in good working condition. Fabricated bedplate.

Crosscut and miter saws with maximum cutting height of 200 mm stable grey cast iron construction precise ball bushing guide of the tool slide on hardened and ground steel shafts Manual saw feed fast up to 65 ° horizontal MITRE setting and 60 ° vertical for adjustable fixed stops lower blade guard to extractor can be connected Machine mounted on mobile machine base with 1,5 mtr. long rollers left and right left side with scale and stop position slider Technical data: Engine: 400 V / 5.0 kW Speed: 2800 RPM Cutting length: 420 mm (at 90 °) Cutting height: 200 mm (at 90 °) Miter range horizontal: 45°-90° - 20 ° Miter range vertical: 60° - 90°-30° Saw blade diameter: 520 mm Dust nozzle: 100 mm Weight: 490 kg

Lifting and Turning Device for beverage paper roll consists of: Jumbo Reel Lifting and Turning Device for beverage carton paper rolls, your choice: manual (manufacturer BT), with battery electrical lifting (manufacturer Tetra Pak)or with battery electrical lifting and autom. hydr. turning (manufacturer BT)

used pipe points cleaning master / atlas type 02V92 construction year: In 1993 nominal width: DN200 nominal pressure: PN100 manual: no

Workspace tip height 102 mm centre distance - with normal headstock with 450 mm - reduction gear headstock 375 mm - over the cheek 200 mm - over the slide 120 mm spindle poles spindle nose for collets type Schaublin W25 spindle bore 25 mm collets passage 20 mm reduction ratio of 1:5 Raedergetriebes cheek height x width x length 168 x 130 x 1000 mm cheek from cast iron, trapezoidal profile as lathe 102 N and dovetail, hardened and ground. Sledge greatest way on the cheek width 400 mm runner - length 90 mm top runner above 80 194 mm way manual adjustment 20 mm shank of tools 12 x 12 mm cross slide width length 94 300 mm way manual adjustment 100 mm bed slide length of leadership on the cheek 250 mm screw lead screw for longitudinal turning and threading, Ø 40 mm screw hardened, Ground thread, slope 4 mm speed range RPM 270 3000 rpm turning 0.02 0.3 mm / Rev. Tapping largest slope  ...

Built: 2003 Location: Germany Brand: TetraTop Model: TetraTop 170V Availability: instantly Technical details: Volume (ml): 1,000 ml, 750 ml, 500 ml Tray Type: TetraTop Flat Top Capacity: 9,000 cartons / h Filling machine TetraTop 170V, commissioning 2004, purchase contract 2003. The rated power of the machine is 9,000 EH /h. Formats: 1,000ml cartons, 750ml cartons and 500ml cartons mileage as of 31.08.2011: 13,772 operating hours. • 1x GSU for granulate transport • 1x granulate hopper • 1x HCCU for foam cleaning • 1x Volume adjustment type 190V converted to stainless steel cylinder • 1x 20 replacement cartridges • 2x tetraPak type Capper 20 screw-on machines for screwing on 38mm screw caps • 1x manual roller transporter for inserting the rollers into the ASU • 1x roller truck for roller transport • 1x retrofit air conditioner Rittal for  ...

Used chamber filter press / filter press Rittershaus & Blecher / R & B 500 x 500 Side holm guided Plate size: 500x500mm Cake thickness: 25 mm Useful length: 2200 mm Chamber number: 47 pieces Filter pressure: 15 bar Closing pressure: min. 220 bar / max. 260 bar Cake volume: approx. 3.9 m3 Total filter area: approx. 17.4 m2 Expiration: closed Plate material: PP Plate transport: manual Filter cloths: optional Pump: Abel diaphragm pump optional

Attachment: Chamber filter press - as good as new, demonstrator Hours of operation: No Usage area: Chamber filter press, pilot plant, wine press Design: page Holm led Filter plate format: 390 x 390 mm Plate number: 14 Filter plates: PP Thickness: 25 mm Filter cloths: optionally available in voting on the medium Procedure: open Filter surface: approx. 2.8 m sq Presses contents: approx. 35 dm3 PCB package length: 391 mm Filter pressure: 15 PSI Plate transport: manually Frame: Steel Product-contacting parts: PP + stainless steel Dimensions: Lxwxh approx. 1695 x 750 x 630 mm Weight: 610 kg (photo identical plant) Pumps: optional Purchase or rent: Tours of the facilities in consultation with us to work. Added: multiple attachments are there about End of April available. Order please, because the demand is very high. You want to rent this facility or to buy? Contact us, we are available.

1 x Francis Shaw model K1 Intermix MK4, Installed new in 1991, fully maintained and checked over by HF in 2005. Net chamber volume: 5.5litres, pneumatic hopper, hydraulic drop door discharge, with Thrigge Scott 45kW DC variable speed motor and controls. Castell Key interlock system Complete and in excellent condition. Chamber and rotors are like new! O/a dimensions: 3m x 1.2m. Can be seen working. All manuals/documentation available.

Attachment: Chamber filter press used Usage area: Chamber filter press, pilot plant Design: page Holm led Filter plate format: 400 x 400 mm Plate number: 15 Filter plates: PP Thickness: 25 mm Filter cloths: optionally available in voting on the medium Procedure: open Filter surface: approx. 3.0 m square Presses contents: approx. 37 dm3 PCB package length: 700 mm Filter pressure: 15 PSI Plate transport: manually Pumps: optional Buying or renting: Visit the facilities in consultation with us to work. You want to rent this facility or to buy? Contact us, we are available.

used injection nozzle cleaning master construction year: In 1993 nominal width: DN200 nominal pressure: PN100 manual: no two machines same to construction exist

Used membrane chamber filter press / filter press Rittershaus & Blecher / VEB Stassfurt 1000x1000 ( Mix package) Plate size: 1000x1000mm Cake thickness: 40 mm Useful length: 5500 mm Number of plates: 60 pieces Filter pressure: 8 bar Membrane pressure: 15 bar Expiration: closed Plate transport: manual Filter cloths: optional Membrane mix package The plant is in good condition. The system is available 15 times !

Used membrane chamber filter press / filter press Rittershaus & Blecher /1000x1000 ( Mix Package) Plate size: 1000x1000mm Cake thickness: 40 mm Useful length: 5500 mm Number of plates: 60 pieces Filter pressure: 8 bar Membrane pressure: 15 bar Expiration: closed Plate transport: manual Filter cloths: optional Membrane mix package The plant is in good condition. The system is available 8 times !

The canister-filler "D-K2-5000" is a pneumatic driven semi-automatic unit. The product to be filled will be aspirated through a tube and filled with a volume piston into the positioned canister. The positioning of the canister under the filling head happens manually. The filling range is max. 5,000 ml. With different programm settings bigger canister can be filled also (e.g. 30 Liter canister). - Capacity: 300 cans/h (depends on product, filling volume, packaging, etc.) - semi-automatic version, movable on wheels volume dosing of liquid and slightly pasty products - Volumetric filling quantity - Pneumatic electric system - The filling process is started by a foot switch - All wetted parts made of stainless steel and food-approved plastics (product-specific changes possible on request) - Dimensions: approx. 1,200 x 1,200 x 1,600 mm Optional: - Multiple sizes shoul ...

Working diameter: 40 - 250 mm Automatic work piece loading and removing for ball diameters: 40 - 105 mm Manual loading for diameters: 105 - 170 mm Direct ball attaching: 170 - 250 mm Rotation speed, stepless: 10 - 300 rpm Grinding spindle speed range: -160 - 3150 rpm -80 - 1580 rpm -38 - 775 rpm -20 - 385 rpm Weight: 6,5 tn Electrical connection: 17 kW Year of manufacturing: 1991

The small laboratory press MHSP5 can perform very well with the round stamp (70 mm diameter) deformations of many materials. By delivering fine (0.5 mm per wheel revolution), deformations are carried out very accurately. Small punching or stamping operations are possible. The press is driven by a worm gear screw jacks, which requires minimal hand strength by high reduction ratio. The pressing frame consists of stable-dimensioned polyamide PA6G. Here are some technical data:-static force 5 KN (0.5 to) - portable presses frame made of polyamide PA 6 G, very stable design, with FEM program added - spindle manual jacks 20 mm, pitch 5 mm - with Handwheel diameter 120 mm and handle - gear ratio 1:10, per the Handwheel 0.5 mm screw - table size 235 195 mm - clearance width 190 mm - stamp size diameter 70 mm with 4 holes 8 mm for mounting a major stamp Very easy operation with spindle and w ...

used filter press Hoesch - cast iron small filter press from cast iron to the filter of liquids solutions, dirty waters, oil, biooil, rapeseed oil-used - with handwheel - downpour filter records 30x30 cm - with collective tub - tilled manual pump - dimension ca 1,00x0,5x0,7 m - weight approx. 300 kg with hand pump the arrangement stands to the rent and for the purchase at the possession.

Attachment: Chamber filter press-neuwertig demonstrator Hours of operation: No Design: page Holm led Filter plate format: 250 x 250 mm Number of plates: 8 Filter plates: PP Thickness: 25 mm Filter cloths: optionally available in voting on the medium Procedure: open Filter surface: 0.56 m m² Presses contents: approx. 7 dm3 PCB package length: 379,2 mm Filter pressure: 15 PSI Plate transport: manually Product-contacting parts: PP + stainless steel Dimensions: Lxwxh approx. 960 x 400 x 360 mm Weight: 350 kg Pumps: optional Purchase or rent: Tours of the facilities in consultation with us to work. Added: multiple attachments are there about End of April available. Order please, because the demand is very high. You want to rent this facility or to buy? Contact us, we are available.

REWA 470 / 27 Product no.: RE-HU-2015-0801-1 Equipment: refurbished dewatering equipment Type: Chamber filter press 470/27 with high pressure piston diaphragm Abel Design: page Holm led Filter plate format: 470 x 470 mm Plate number: 27 Filter plates: PP Thickness: 30 mm Procedure: open Filter cloths: optionally available in voting on the medium Open filter surface: approx. 10.1 m ² Presses contents: approx. 135 dm3 PCB package length: 1600 mm Filter pressure: 15 PSI Closing pressure: approx. 380-410 bar Plate transport: manually Pumps: Abel piston diaphragm high pressure pump Accessories: depending on the type and customer Extra services: On this complex guarantee months between 6-12. Condition: The system is in good condition and is ready for use immediately. Buy or rent: Visits of facilities in consultation with us in the work. You want to rent this facility or to buy? Contact  ...

1 of used wrap-around /traypacker, make ZVT (KHS), type Innopack WP 030 VH. New 2000. Operating side; left. Capacity upto 30 cartons/trays per minute (depending on product and blank dimensions). Siemens S7 PLC with OP 17, Indramat Servos, Nordson hot-melt unit. Wired for 400V / 50 Hz. Used for packing various 330 ml upto 2.000 ml glass and PET bottles as 8/12/20/24 on tray or in full wrap-around cartons. Last used as tray-packer only. Various manuals available. Condition: good. Dismantled and available cleaned ex-warehouse The Netherlands.

NEW Bainite model BMIM95 95 litre intermeshing type mixer Customs Tariff CN Code: 8477.8093 Manufacturer: Bainite Machines Pvt Ltd Net chamber volume: 95 litre Rotor speed: 6 - 60 rpm Rotor type: HP-5 design (intermeshing) Dust seals: SSA (self-sealing arrangement) Motor power: 420kW, 1000rpm AC motor, 3ph, 50Hz, 380/400V Discharge door: Hydraulic drop door with linear actuator and toggle latch. Two (2) J Type thermocouples mounted in door top as standard One (1) Single acting pneumatically operated oil injector Feed Hopper Assembly: Hydraulically operated Floating weight: single ?V? bottom type Gearbox: Full unidrive type with S.F. 2.25 Bedplate: Fabricated steel Ancillaries: Dust stop lubrication (1.5HP x 2), hydraulic pump unit (20HP) Three (3) Zone closed loop temperature control (TCU) Electrical Controls: Schneider make variable frequency drive (VFD) controls with ...

1 of used shrinkpacker (sleever with shrinktunnel), make KHS Kisters, type SP 035 V Basic, new 2003. Operating direction: left. Capacity upto 35 cycles/minute (in overspeed). Metering-belt type infeed. For over-wrapping & shrinking pre-packed trays. Last used for various collations of glass / PET bottles (330 - 2.000 ml) on tray. Suitable for print-registered film. With Siemens S7 PLC and Simatic OP, Indramat drives. Wired for 400 V / 50 Hz. Various manuals available. Condition: good. Available ex-warehouse The Netherlands.

Used line for the production of the co-extrusion by PST Forming method. PTI - The twin screw extruder DS 92/28   2x screws with a diameter of 92 mm The length of screws 28 x L / D Snails closed system with internal temperature control, deep nitrided, with degassing on the cylinder, extruder equipped with a vacuum pump with filter, Siemens Servo Motor power: 60 KW Torque: Nm 15700 Screw rotation: 0 - 50 rev. / Min. Zones with ceramic heaters with an intense cooling: 5 x 5 KW Cooling Zones: 4 Performance with hard PVC, depending on the materials and tools: max.600kg / h Length: 4500 mm Width: 1600 mm Height: 2300 mm           Extruder equipped with a microprocessor control SIEMENS type Extrusion Pro Pak visualization 2. Co-Extruder PTI - The twin screw extruder DS 68/28 Snails with a diameter of 2 x 68 mm Length of the screws: 28 x L / D Snails cl ...

High speed press Original Manufacturer by: BRUDERER Type: BSTA 30 Technical data: Stroke power 300 KN (30 tons) Adjustable speed 100 - 600 strokes per minute up to 10 strokes in one second Equipped with synchronized BBV feeder Feed pitch up to max. 60 mm adjustable, highly accurate With PLC control Three working mode: single punch, complete stroke and full automatic Emergency stop Pneumatic clutch and brake Weight approx 2.5t Automatic in feed, fully synchronized with punching moment Tool and coiler not included (price on request) Technical Air 8 bar Operators instruction manual Machine with new CE certificate Overhauled - Rebuilt by Silicon plus

Used eccentric screw pump Bornemann E2H 1024 Built: 1993 Power: 4 kW Voltage: 400/690 V Flow rate: 10 m3/h Speed: 370 rpm Viscosity: 10000CST Conveyor pressure: 2 bar Suction flange: DN80, top Pressure flange: DN65, axial Manual: yes Machine number: 329495

Attachment: Chamber filter press used semi mobile Model: pilot plant on platform mounted Design: page Holm led Filter plate format: 400 x 400 mm Chamber number: 20 Thickness: 25 mm Filter plates: PP Filter cloths: optionally available in voting on the medium Filter surface: approx. 4.72 m m² Presses contents: approx. 56 dm m³ PCB package length: 1024 mm Filter pressure: 15 bar Closing pressure: 380 bar Operating temperature: min 10° MAX 50° Plate transport: manually Pumps: optional Motor voltage: 380 V Control voltage: 230V - 24 V Optional accessories: according to customer requirements and design Condition: It is a complete semi-mobile system on platform mounted, incl. control cabinet as full drainage system. This compact drainage system is easy to transport and can be taken in a very short time in operation. Appendix: Selling without trailer You want to rent this fac ...

we offer for MRI-use... Medrad MRI Dual-Head-Injector Typ: Spectris incl. TESTING FROM OEM Technican - Injector Head PEDESTAL unit - Head control unit - optical Transmitter/Receiver - Display control unit - Master control unit - Operation manual...englisch language - cable/etc. fully tested from OEM technican YOU ARE WELCOME TO INSPECT

Qty. 1 Second-hand ingot caster plantMfc.:Sistem TeknikBuilt:1/2015Stopped in 4/2015Recycling capacity:5000 Ton/annumQty. 12 Units of Pyrotek moldsDim. of aluminium ingot: 1000 x 1000 x 500 mmWeight:500 kgCharging material: Aluminium cans, profiles, sheets, motor blocks, wheels etc.Scope of supply:Aluminium shredderMagnetic separator Aluminium de-coating machine Baler Aluminium gas furnace Aluminium casting system Gas generator Mass ARUN spectrometer Air compressor, conveyors, forklift, ect.Shredder and magnetic separation conveyorMfc.:YSSType:Mono shaft shredder J600Capacity:500 kg per hour high power electrical shredding machineMono shaft shredder stylePLC automatic control unit Siemens?Hydraulic unit for material pushing to shredding wheelCurrent control for shredder reverse †safe usageShredded aluminium pass onto conveyor unitMagnetic separation system for steel removalElec ...

Standard equipment Manual heavy duty band saw machine with hydraulic Sawframe reduction for miter cuts from 45 ° left to right 65° Saw frame made of sturdy cast iron construction Massive round table Oil bath gearbox consisting of bronze wheel with hardened and ground steel worm Carbide Guide and adjustable roller bearings Quick clamping Vice with additional quick adjustment and quick release lever Electric high-performance Coolant pump Mechanical blade tension with electric blade monitoring Control tool Free delivery including packaging

Engine power: 1,1 kW, 230V / 1PH motor coolant pump: 50 W Feeding: manual Blade speed: 20-65 m / min Number of steps: infinitely variable Band saw blade dimensions: 1,735 x 12.7 x 0.9 mm length Vice open/closed: 1,120 / 930 mm width without / with material stop: 510 / 720 mm Height lower / upper final position saw bracket: 1240 / 1,590 mm Net weight: 100 kg G & pieces 3300150SE Option: 3 Piece bi-metal band saw blades HSS

Q Ferquenzumrichter 140kVA ABB - AV GmbH ACS607-0140-3 Fig. 4 quadrant converter (Rückspeisefähig!) compl. built in switch cabinet. Dimensions H = 2010 T = 640 B = 1200 (2-door). Technical data: Eingangsfreq. 46.63 Hz Ausgangsfreq. 0.. 300 Hz U = 380TH. 415V IP21 (Cabinet) Wiring diagrams available ABB Manual: ABC://abc05.ABB.com/global/Scot/scot201.nsf/veritydisplay/fdc8e06693b9 114ac2256df0003fe70e/$file/en_6047hw_5d_scrres_plus_update_note.PDF Net price in FU Wardrobe (2 PCs.) 6,500 Questions under 0170 / 2204056 or fa.raupp@t-online

generally refurbished and modified; for roasting batches between 10 and 25 kg of green coffee; roasting time between 10 and 22 min.; heating with natural gas or propane including cooling filter, roasting cyclone with fan, new burner and new manual control with digital temperature display paint according to customer requirements extension with raw coffee supply and flue gas cleaning according to customer request

3-roll hydraulic with dual pre-pinch planetary configuration. new to complete, 45 days from order. -Plate width 3000 mm -Capacity rolling plate thickness 50 mm -Pre-pinch plate thickness 40 mm Machine configuration and accessories installed: -useful surface length on the rolls 3100 mm -upper roll size 480 mm -lower rolls size 440 mm -Digital position readouts. -Hardening treatment of the 3 rolls. -3 rolls driven hydraulic motorized with independent axial gear box on each roll. -Conical plate bending attachment with tiltable lower rolls hydraulic. -CE quality certification, Made in Italy manufacturing. -Service manuals and operation instruction manuals. -Hydraulic diagrams -Electric & electronic schematics with parts list. -Set of service tools for maintenance. -Electric power installed 50Hp. -3 phase voltage to be specified Warranty 12 months.  ...

Accessories: -Three-jaw Chuck -Steel holder multi fix A -Lamp -Coolant Technical data: Tip height 120 mm Top width 450 mm Spindle passage 23 mm Spindle inner taper MK 4 Plan travel 150 mm Tailstock MK 2 Quill way 80 mm Manual 9 levels Speed range 2 travel of bolt turn 30 3000 rpm

Attachment: Chamber filter press used Design: page Holm led Filter plate format: 400 x 400 mm Chamber number: 30 Thickness: 25 mm Filter plates: PP Filter cloths: optionally available in voting on the medium Procedure: open Open filter surface: approx. 7.5 m square Presses contents: approx. 90 dm m³ PCB package length: approx. 1512 mm Filter pressure: 15 bar Closing pressure: 380 bar Operating temperature: min 10° MAX 50° Plate transport: manually Hydraulic pump: optional Motor voltage: 380 V Control voltage: 230V - 24 V Optional accessories: according to customer requirements and design Safety equipment: optional Optional accessories: optional possible depending on design Extensions: In consultation according to the design Special services: Refurbished service to customer specification is optional. The system goes through a service check or a complete overhaul before delive ...

Part cleaning system cleaning system part cleaning machine cleaning equipment Metal cleaning equipment Kliro Centrimat L 15 kg Year of construction 1998 Panel Mount ACP protected 6000 with internal conveyor Centrimat C3 manual The original price of this machine was 25,000 euros. The machine requires no additives to clean, but the parts are cleaned by the centrifugal force. Device 2.300 kg Cabinet 50 kg Dimensions: Footprint unit without Cabinet 1200 x 1200 mm Height 1680 mm Cabinet 650 x 650 mm Height 1960 mm KLIRO Anlagenbau Marienheide No. 5700145 VEM motors GmbH Wernigerode K11R 132 No. 88 Rothstein protection systems GmbH Marienheide Siemens COROS OP3 RITTAL-Werk Rudolf LOH GmbH Herborn AE 1360 No. 134617 RITTAL-Werk Rudolf LOH GmbH Herborn AE 1556 No. 039556 Maschinenfabrik bihler Halblech type B-4 No. 22732 Machine is fully functional.

CARVING machine type MARIANI PL 8 second hand machine working conditions : good with Frequency Converter HF rotary device for the simultaneous rotation of the model and the pieces manual chuck of mandrins unit also to work with flat pieces Technical Details : n.8 spindles distance betwen spindles mm. 420 n.02 rotation speed of spindles rpm 9.000 / 12.000 max. working length ( on rotation ) mm. 1900 volt. 380/50 net weigth kgs. 2500 overall dimension mm. 5000 x 2800 H=mm.1500 ( machine assembled ) Volt. 380/50

Working length: 1020 mm Maximum sheet thickness: 2.5 mm Maximum opening width: 48 mm Bending angle: 0-135 ° Width: 1350 mm Overall width: 820 mm Height: 1140 mm Approximate weight: 285 kg FEATURES -Universal bending machine for sheet metal working and repairers -Sturdy construction in modern design -Easy adjustment of the upper beam by means of foot pedal, hands are free for the workpiece - manual bending machine for standard bending tasks -Segmented clamping beam for a large number of bending possibilities -Optimum price-performance ratio -Faster and easier bending operation via handle -Non-slip rubber coating on the foot pedal for safe working -Easy adjustment of the lower beam on the corresponding thickness -High upper beam for the manufacture of highly bent profiles Action price, including free home delivery to 1 address Germany (Mainland)

Dynamic airflow separator (sifter) for minerals, cement, recycling etc., rotor diameter: 700 mm, turbine wheel occupied with 64 blades / turbine blades, outer ring occupied with 36 manually adjustable counter wings, incl. drive. In very good condition.

Attachment: Chamber filter press used Design: page Holm led Filter plate format: 470 x 470 mm Plate number: 26 Filter plates: PP Thickness: 30 mm Procedure: open Filter cloths: optionally available in voting on the medium Open filter surface: approx. 9.7 m m² Presses contents: approx. 130 dm3 PCB package length: 1500 mm Filter pressure: 15 PSI Closing pressure: approx. 380-410 bar Plate transport: manually Dimensions: Lxwxh Empty weight: Accessories: depending on the type and customer Special services: Refurbished service to customer specification is optional. The system goes through a service check or a complete overhaul before delivery. On these systems, we guarantee between 6 to 12 months. Condition: The plant is located in a very good condition and is ready for use immediately. Buy or rent: Visits of facilities in consultation with us in the work. You want to rent this facility ...

High-efficiency dynamic classifier (separator) for minerals, cement, recycling etc., rotor diameter: 700 mm, turbine wheel equipped with 64 blades, outer ring equipped with 36 manually adjustable counter-blades, incl. drive. In very good condition.

Italian top make, control Grundig manual-plus V 260, very robust machine! Top width 1500 mm maximum swing over bed 625 mm Spindle bore 105 mm Taper MK 5