mahr 40 used for sale

Commonrail pump As good as new with 400 hours

Boku RS 40 E with 1 kettle, 1 broom Machine cleaned and tested.

turning diameter: 400 mm swing diameter: 420 mm x-travel: 850 mm z-travel: 315 mm spindle head DIN 55026 - Size: 11 spindle bearing diameter: 140 mm turning speeds: max. 4000 U/min tool turret 12 times: C5 Capto rapid traverse x + z axis: 45 / 30 m/min feeding force: 11 kN total power requirement: 58 kW weight of the machine ca.: 9 t dimensions of the machine ca.: 9,5 x 4,5 x 3 m Hard turning Dry machining Chip conveyor Promot Portal and Cellmaster No clamping device available No tools available no Cellmaster accessories available The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

TECHNICAL DETAILS Travel X x Y: 4000 x 2000 mm Cutting range X x Y x Z: 4064 x 2032 x 70 mm Workpiece weight: 1270 kg Positioning speed per axis / simultaneous: 100 / 140 m/min Axis acceleration: 12 m/s² Position accuracy: ±0.1 mm Repeatability: ± 0.05 mm Edge Detection Accuracy: ± 0.5mm Table: Interchangeable table system Laser Source: Fiber 4000 Power: 4000 W Wavelength: 1μm Polarization: unpolarized Pulse Rate: 1 - 2500 Hz Sheet thickness steel: 20 mm Sheet thickness aluminium: 15 mm Sheet thickness stainless steel: 15 mm Sheet thickness copper: 8 mm Sheet thickness brass: 8 mm MACHINE DETAILS Dimensions: 12.9 x 6.75 x 2.5 m Weight: 15 t Power: 25 kW Switch-on time: 23,477 h Laser switch-on time: 5,248 h

Key data: 45 °, 3 mm, 2 mm

SCM SiI400N Sliding Table Saw Mark SCM Type SI400N M-No.: AB/127843, 071528 Built in 1999 Edging table 3,200mm Saw blades ø 250-400 mm Main saw 5.5 kW, 3000-4000-5000 tpm. Cutting height 130 mm. (Saw blades. 400 mm.) Saw blade swivel 0 - 45° Scoring ø mm, ID: 20 mm Engine: 0.75 KW, 8,500tpm Cutting width 1,500 mm Rip fence stop ruler in anodised aluminium Lay-down table: steel Lay-down table with licence for angle cuts Length stop anodized aluminum with 2 flaps Control panel Digitale-analoge zaaghoogte aflezing Condition Fully functional, very SCM maintained

Manufacturer: Bitzer Model: 2JES-07Y-40S Machine Type: Semi-Hermetic Refrigeration Compressor Condition: New Supply Voltage: 400V / 3Ph / 50Hz Shipping Weight: 50 kg Net Weight: 43 kg Compressor Details: • Type: Semi-Hermetic Piston Compressor • Series: CE1 • Number of Cylinders: 2 Ncebjwudyqemy Ex Ipou • Flow Volume: 5.21 m³/h • Compression Type: Piston • Oil Type: BSE32 (BSE55 for R134a, R450A, R513A, R1234yf if tc > 70°C) • Oil Charge: 1.0 L Electrical Data: • Starting Current (LRA): 14.8 A • Max Operating Current: 3.7 A • Max Power Consumption: 1.9 kW Refrigerant Compatibility: R134a, R450A, R513A, R1234yf, R404A/R507A, R448A/R449A, R454C, R455A, R407F Pipe Connections: • Suction Line: 16.0 mm (5/8") • Pressure Line: 12.0 mm (1/2") Sound Power Level: 63.0 dB(A) at +5°C / 50°C Dimensions: • Width: 220 mm • Height: ...

Key data: 45 °, 3200 mm, 1250 mm

Griggio Unica 400 sliding table saw Mark: Griggio Type: Unica 400 Year of Make: 2010 M-No.: MC00101468 Main saw: ø400 mm, saw protrusion 125 mm, inclination 0-45° Saw blade height-, -bevel adjustment: electric with digital display Speed: Saw blade protruding: 0-125 mm electric with digital display Saw blade tilt: 0 - 45° electric with digital display Motor: 7.5 KW Vorrits saw: 0.75 KW, ø125 mm Trolley 3,200 mm Cutting width: 1,250 mm electrically with digital display on the width stop Length stop: 2,200 - 3,300 mm Lay-down table: steel with scale angle display, adjustable support support and product-friendly roller Extraction: Top: ø80 mm, Bottom: ø120 mm Weight: 820 KG

High: 2.900 mm, Long: 2.200 mm, Speed: 22.4 / 2.800 r.p.m., Width: 900 mm, Weight: 2.350 kg, Voltage: 220 / 380V, Ø column: 300 mm, Ø spindle: 80 mm, Total power: 5.3 kW, Spindle displacement: 360 mm, Surface of the table: 1,300 x 750 mm, Do not. drill spindle speeds: 15, Advances min / max spindle chuck: 0.032 / 1.5, Number of drill spindle advances: 12, Max. distance spindle axis column: 1.200 mm, Maximum distance table to spindle: 1.100 mm, Minimum distance table to spindle: 750 mm, Specification: Radial

Cooling equipment - weight: 200kg L 1,700 x W 800 x H 900 cm, High: 2.100 mm, Long: 2.400 mm, Width: 2.400 mm, Weight: 2,500 Kg., Voltage: 380 V, Total power: 4 Kw, Wheel speed: 2,250 / 6,000 rpm, Grinding length: 400 mm, Ø max workpiece: 320 mm, Transversal stroke: 260, Longitudinal stroke: 400 mm, Distance between points: 700 mm, Race car rolling (x axis): 400 mm, Vertical travel of trolley wheel: 280 mm, Specification: Universal

Key data: 400 t, 30000 mm

The machine is in good technical condition, inspection and test drive is possible by prior arrangement.

A centerless CNC cylindrical grinding machine Tschudin is available. Workpiece diameter min./max.: 1.5mm/100mm, max. grinding length: 250mm, grinding wheel diameter outside/inside: 400mm/203.2mm, grinding wheel peripheral speed: 50m/s, grinding wheel power: 11kW, control wheel diameter outside/inside: 225mm/127mm, speed: 265rpm, inclination: +/-5°, power: 3.7kW. Machine dimensions X/Y/Z: approx. 2000mm/2400mm/1900mm, weight: approx. 6000kg, control: Fanuc 21i-MB. Including Knoll Micro Pur 240 F ultra-fine filter, Streuli SHSRT300-TL142/180 lifting station and Kraft & Bauer FB703S-UV3-TFM70° fire extinguishing system. Documentation available. On-site inspection is possible.

CDM PREALPINA USED EXTRUSION LINE, for HDPE LDPE LLDPE PS PC ABS PP, nominal throughput rate 380 kg/h (depending on material and feeding rate), ABB Main drive 117 KW 380 V 50 H 3Ph (65% used in work), loading hopper, extruder with heaters and vents, fitted with a 105 mm Ø screw 40 L/D, n.1 vacuum degassing pump, semi-automatic non-stop hydraulic screen-changer (200 mm Ø)complete with hydraulic pack, water ring pelletizer, drying centrifuge, electric cabinet, CE compliance, User’s manuals, Electrical drawings, The line is offered either CHECKED or RECONDITIONED to various extents., capacity: 300-430 kg/h nominal

WATER RING HORIZONTAL PELLETIZER, Constructed in a stainless steel sturdy structure, 16.25 kw installed power, for PE PP production average 300-400 kg., steam extraction vent, water-water heat exchanging unit (to be connected to a chiller), N.1 die (customized to project), N.4 rotating knives, N.1 blade-holder, N.1 blade adjusting template, N.1 thermoregulated area, Heating power 6 kW, Cutting drive power 3 kW, No. 1 water pump for water re-circulation, ELECTRIC CABINET (OPTIONAL - can be connected to extruders cabinet), This machine is available in other sizes and in dry version., When submitting your enquiry, please give details of :, - MATERIAL type and size, - CAPACITY required, - if CABINET is needed or possible connection with existing extruder cabinet, installed power - used power in work: about 60-65% : 16.25, capacity: 300-400 kg/h

Availability: as of now Current format: 170 x 92 x 25 mm Performance: 40 cycles Step offshoot: yes Gluing machine: on request Machine is in good and functional condition according to its age

Holke F-10-V X: 815 - Y: 400 - Z: 420 mm Max longitudinal travel X-axe: 815 mm Max cross-travel Y-axe: 400 mm Max travel Z-axe: 420 mm Power on spindle: 2 HP Admission in millinghead: ISO 40 Max quill travel Z´: 130 mm Spindlespeeds: 57 > 2275 rpm Table size: 1120 x 255 mm Weight: 1300 kg

diameter: div. number: 40x tool adaptor: BT 40 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Pinacho SC 200 Ø 402 x 1000 mm Distance between centers: 1000 mm Swing over bed: 402 mm Swing over cross-slide: 380 mm Swing in gap: 560 mm Diametre of main spindle bore: 42 mm Power on main spindle: 4 kW Number of speeds: 40 > 2800 rpm Digital screen: yes Length: 2390 mm Width : 910 mm Height: 1625 mm Weight: 1190 kg

diameter: div. number: 40x tool adaptor: BT 40 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

kop kan draaien: 90° (R amp; L) / 45° (F amp; B) 360° bovenarm draaibaar spindelhartlijn tot kolomoppervlak: 71 gt; 476 mm Max longitudinal travel X-axe: 750 mm Max cross-travel Y-axe: 305 mm Max travel Z-axe: 406 mm Max height workpiece: 70 > 476 mm Power on spindle: 2 HP Admission in boring head (ISO): ISO 30 Spindlespeeds: 3750 rpm Length: 1435 mm Depth : 1600 mm Height: 2100 mm Weight: 1 ton

4 Kopf Bohrmaschine / 4 head Paper Drilling machine Josef Foellmer IRAM 400/445Serial-No. 2190

Bread cutter with circular knife for cutting oven-fresh products without the use of oil! for approx. 35cm loaves of bread with approx. 25cm width and approx. 15cm height Lens thicknesses from 4-24mm selectable Output approx. 130 sections per minute with bread rack for bagging with safety cover completely stainless steel clad Dimensions: W 80 x D 70 x H 110cm

Kopierrahmen / Copyframe O.M.S. COPYSTAR 4050

Laser power: 4000W (4kW), wavelength: 1030nm, beam quality (BPP): 8mm/mrad, beam diameter setting: 0.1µm, machine dimensions X/Y/Z: approx. 1000mm/1600mm/1600mm, weight: approx. 1000kg. Including 2x scanner optics (PFO) for the process cells, 3x fiber optic cables and spare parts. Documentation available. On-site inspection is possible.

Buchstraße-Hardcover / Casing In Line Kolbus BF 40T Year 1977 - Serial-No. 558 Format / Size min. 100x125mm - max. 270x365mm Buchblock Dicke / Book block thickness 6 - 70mm Leistung / Mechanical speed max. up to 40 Takte/min. Buchstraße Ausstattung / Casing in Line consists of: Fliessdreischneider / Three knife Trimmer Wohlenberg Modell 44 Rundungsstation / Rounding Station Hinterklebestation für Gaze Kapitalbandstation / head-tailbanding and backlining station Deckenanleger / Case Bending Station Falzeinbrennstation / Pressing Unit Kolbus FE Pressing Stations with Heated Joint Forming

Falz- und Buchblockpresse / Nipping and Smashing Kolbus FM 405 - AB 370 Buchblockfalz- und Ganzpresse mit Buchblockanleger Book Block Joint and whole Block Press with Book block feeder Baujahr / Year 1988 - Serial-No. 308 Format (unbeschnitten) / Size (uncut) min. 125 x 100 x 6mm - max. 380 x 290 x 80mm Sehr guter Zustand / Very good Condition Maschinengewicht / Machine weight 4200kg

Polyester fiber production line Polyester fiber production line, manufactured in 2008, put into operation in 2010. From the end of 2012 until the second half of 2019, fiber production was suspended. The productivity of the line is 10,000 tons of fiber per year. The possibility of producing fiber from primary raw materials - PET granules and from secondary raw materials - PET flakes (recycled PET bottles). The main default raw material (as cheaper) is PET flakes. The available spinneret can be used to produce solid fiber 3, 7 and 15 denier, and hollow fiber, 7 and 15 denier. Hollow fiber can be produced in the "conjugated" type. Can buy and use other denier spinnerete according needs. The main components of the line: Fiber extrusion line • Vacuum dryers, volume 8m3, heated with thermal oil, year of manufacture 2011 – 4 units. + In 2019 instaled, elevators and a screw conveyor for  ...

Pressing force: 3200kN, enlarged stroke: 810mm, working width: 4050mm, ram speed: downwards: 130mm/s, pressing: 6.5mm/s, upwards: 75mm, stop time: 109ms, safety distance: 174mm, weight: approx. 29000kg, operating hours: 16010h, control: Cybelec ModEva 15S. Including 4 bending aids and angle measuring sensor. Dies, embossing tools, pointed punches, roe foot punches, closing bar, extension for upper tool, radius tool and adapter available on request. Documentation available.

Rectifieuse par coordonnées CNC HAUSER S40-400 CARACTÉRISTIQUES TECHNIQUES: Course axe X : 650 [mm] Vitesse maxi. course axe X : 4000 [mm/min] Vitesse avances de travail axe X : 0 - 1800 [mm/min] Course axe Y : 450 [mm] Vitesse avances de travail axe Y : 0 - 1800 [mm/min] Course axe Z : 130 [mm] Vitesse mini. course axe Z : 0.5 [mm/min] Vitesse maxi. course axe Z : 12000 [mm/min] Fréquence course axe Z : max. 4 [Hz] Course axe W : 500 [mm] Vitesse axe C (planétaire) : 5 - 250 [rpm] Vitesse maxi. course axe W : 800 [mm/min] Course axe U (avance radiale) : 5.5 [mm] Distance entre colonnes : 750 [mm] Longueur table : 770 [mm] Largeur table : 630 [mm] Passage libre entre le moteur de meulage et la table : 585 [mm] Poids maxi. admissible sur la table : 500 [Kg] Tension d'alimentation : 400 [V] Poids : 4550 [Kg] INFORMATIONS COMPLÉMENTAIRES : x1 pack H ...

Rectifieuse par coordonnées CNC HAUSER S40 400 CARACTÉRISTIQUES TECHNIQUES : Course axe X : 650 [mm] Vitesse maxi. course axe X : 4000 [mm/min] Vitesse avances de travail axe X : 0 - 1800 [mm/min] Course axe Y : 450 [mm] Vitesse avances de travail axe Y : 0 - 1800 [mm/min] Course axe Z : 130 [mm] Vitesse mini. course axe Z : 0.5 [mm/min] Vitesse maxi. course axe Z : 12000 [mm/min] Fréquence course axe Z : max. 4 [Hz] Course axe W : 500 [mm] Vitesse axe C (planétaire) : 5 - 250 [rpm] Vitesse maxi. course axe W : 800 [mm/min] Course axe U (avance radiale) : 5.5 [mm] Distance entre colonnes : 750 [mm] Longueur table : 770 [mm] Csbn Ua Hjwu Dwpe Rwjrd Largeur table : 630 [mm] Passage libre entre le moteur de meulage et la table : 585 [mm] Poids maxi. admissible sur la table : 500 [Kg] Tension d'alimentation : 400 [V] Poids : 4550 [Kg] ÉQUIPEMENTS INCLU ...

Stroke speed cut/return: 80m/min, feed cross support/long support: 27mm/stroke, table dimensions X/Y: 4000mm/1250mm, max. table load (table center): 2000kg, tool holder: planing steels with rectangular cross-section, tool dimensions X/Y: 50mm/50mm, bed length: 9400mm, planing length: 4500mm, planing width: 1520mm, planing height without/with cross support: 1310mm/1250mm, connected load: 64kVA. Total system dimensions X/Y/Z: approx. 10000mm/3300mm/2500mm, weight: approx. 26000kg, foundation weight: 60000kg. The machine was electrically re-equipped in 1986. Documentation available. On-site inspection is possible.

WILLEMIN MACODEL W408 MT CARACTÉRISTIQUES TECHNIQUES : Année : 2007 Type de CN : FANUC 16i-MB Nombre d'axes : 5 Course axe X : 250 [mm] Course axe Y : 200 [mm] Course axe Z : 300 [mm] Vitesse déplacement rapide X, Y et Z : 30000 [mm/min] Diamètre maxi. en barre broche de tournage : 32 [mm] Vitesse maxi. broche de tournage : 6000 [tr/min] Puissance maxi. broche de tournage : 3.7 [kW] Course angulaire axe C : 360 [°] Course angulaire axe B : 115 [°] Attachement broche : HSK-E40 Vitesse mini. broche 500 [tr/min] Vitesse maxi. broche : 30000 [tr/min] Puissance broche : 10 [kW] Nombre de postes magasin d'outils : 48 Longueur maxi. d'outil : 95 [mm] Diamètre maxi. d'outil : 63 [mm] Capacité bac d'arrosage : 80 [l] Débit pompe d'arrosage : 40 [l/min] Courant nominal : 25 [A] Tension d'alimentation : 400 [V] Poids : 1700 [Kg] ÉQUIPEMENTS INCLUS :  ...

A CNC fine milling machine Iselautomation KG with defective spindle is available. Travel X/Y: 400mm/200mm, machine dimensions X/Y/Z: approx. 1200mm/900mm/1600mm, weight: approx. 500kg. On-site inspection is possible.

Two identical Burkle curved belt conveyors are available. Effective width: 400mm, length: 1800mm, feed rate: 37m/min, curvature: 90°. Documentation available. On-site inspection is possible.

met 13 meter invoerrollenbaan met digitale uitlezing Dia saw / abrasive - disk : 400 mm Turningspeeds: 10/20 m/min Weight: 1250 kg

Cylindrical Grinding Machine TSCHUDIN type HTG 400 Between points: 400 mm Centre height: 100 mm Cone: CM4 Spindle speed: from 70 to 500 RPM Max table travel: 420 mm Table orientation at 15° Grinding wheel: Ø 300 mm Retractable tailstock CM3 Machine rebuilt by REWITECH SA (Switzerland) in 1995 Equipped with one settling tank PHILIPS Voltage: 380 V Dimensions (L x W x H): 2000 x 1400 x 1600 mm Weight: approx 1,5 T

Key data: 585 mm, 4064 mm

JARBE Universal Cylindrical Grinder Year: 1981 Technical Specifications & Features: • Swing Over Table: 23″ Distance between centers 160” • Hydraulic Table Traverse • Swiveling Table for Taper Grinding • Universal Workhead • Universal Wheelhead • Grinding Wheel Capacity: 20″ • Includes 2 Workrests • Equipped with Coolant System • Electrics: 440 Volt

saw blade diameter: 400 mm cutting diameter: 125 mm Cutting length: 650 mm cutting speed: 14 - 30 - 45 m/min total power requirement: 5,0 kW weight of the machine ca.: 1,2 t dimensions: 2,0 x 1,0 x 1,6 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Heidolph Laborata 4001 complete with condenser and water bath, 0-270 rpm

Screw Compressor WORTHINGTON - CREYSSENSAC Type Rollair 40 -- RLR 40BM6Fabr. No. 6240330200 built in 2003Volume flow rate 4.6 m3/min. Pressure capacity 10 barMotor power main motor 30 kWNe-connection 400 Volt, 50 HzConnection thread 1 1/2 inch- 36004 Switch-on hours read- 19256 load hours read- SoundproofedSpace requirement L x W x H 1850 x 1050 x 1760 mmWeight 910 kggood condition; used

CNC Univ. Tool Grinding Machine SCHÜTTE Type BU 400 CNC 4Machine - Defect - without ControlMachine not ready for operation - electric without function - without CNC controlFabr. No: 03-02 Year of manufacture 19904 axes (X, Y, Z and R)Table clamping surface 1300 x 250 mmCenter width 700 mmCenter height 155 mmGrinding length (X-axis) max. 400 mmGrinding width (Y-axis) max. 260 mmGrinding spindle speed max. 6000 rpm. Grinding spindle drive 3 kWNet connection 380 Volt, 50 Hz, 25 Amp.- CNC control

Key data: 4000 kN, 80 mm

Machine + Viper Robot 12

SPECIFICATIONS: Operation of the machine with rotating ring, diameter mm: 400 Installed power: 2.7 kW EQUIPMENT: 01 Roller conveyor for loading 01 Roller conveyor for unloading

Conveyor belt, trough conveyor belt, trough conveyor presumably GASUS type FB 400 x 5500Belt conveyor, conveyor belt, belt conveyor Fabrig Nr: F-02071168 Year of construction 1996Working length: 5.5 metersBelt width: 400 mmDeflection pulley diameter: 225 mmDeflection pulley width: 450 mmBelt speed: approx. 30 meters/min. Motor power: 1.5 kWNerg connection: 400 volts, 50 Hz - Drive via tubular motor- Inlet hopper 600 x 400 mm- The support stations are 2-part troughed- Metal support rollers with maintenance-free ball bearings-

Impulse Shielded Gas Welding Machine REHM Type RMP 400 Hybrid (REHM Mega Pulse)Pulse Welding Machine with Inverter Welding Power SourceFabr. No. 065013 built in 1998Power 400 Amp. = 60% ED 320 Amp. = 100 % EDEinfinitely variable adjustment rangeMains connection 400 Volt, 50 Hz, 32 Amp. Plug - separate 4-roll wire feeder with connecting hose pack meter - Digital display for voltage and current- Pulse welding device with single and double pulses - 2-stroke and 4-stroke welding device - 4 meter Binzel hose pack with

Conveyor belt, belt conveyor, belt conveyor MOVING (Sweden) Type BGL22-02-4000-800Order No: 4019584 year of construction 2004Effective length: 3900 mmBelt width: 800 mmBelt length: approx. 8100 mmOverall height frame profile: 120 mmDeflection pulley diameter: 105 mmBelt speed: approx. 10 m/min. Conveyor belt height: approx. 900 to 1300 mmMotor power: 0.25 kWNerg connection: 400 volts, 50 Hz.- Drive via ABB/ geared motor- Movable on 6 fixed castors with brake- Inclined position of the conveyor belt due to different heights of the 3 mobile footrests -