We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
119,321 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
Capacity: 50.000 bt. / h Currently equipped for 0.25l Vichy / 0.25l Gastro / 0.50l GdB / 0.70l GdB / 0.75l GdB / 0.75l Benelux / 0.75l Gastro Bottles. • Inspection of the mouth sealing surface • Inspection of the side wall (both sides) • Inspection of the thread • Detection of conductive residual liquids • Detection of residual liquids by IR • Diversion of faulty bottles • Diversion of bottles exceeding height and/or width as well as lying bottles Incl. module for detection of impact spots Incl. blower for removal of water drops
used
Capacity: approx. 30.000 l / h
used
Capacity: approx. 25,000 l / hr
used
Capacity: approx. 25,000 l / h
used
Used Heuft Empty Bottle Inspector InLine IXs reflexx Device No. 2ZG044698 Condition: very good, ready for use at short notice · Commissioning 6 May 2012 · Upgrade for later integration of additional ground control using X-ray technology · Tape control Heuft Synchronous TX · Network Heuft Hlan · Haylofts two ways discharge with div. Heuft container transport Convejor · Troubleshooting Software Wizard · Software assistant guided instructions for the different container changes · Power max. 46,000 fl./h · 5 Variety licenses incl. scope of delivery: · Belt control Spectrum TX · Measuring bridges for inlet control and discharges incl. height connections · 2 x Discharge Delta K ...
used
Used Heuft Glass Empty Bottle Inspector InLine reflexx Device No. 2ZG042943 Condition: very good, ready for use at short notice · Original delivery date 12.2011 · Power max. 46,000 fl./h · Pass direction from left to right · Two triggers · Secomak blower instead of compressed air · Transponder detection for RFID test bottles · Discharge monitoring · Network Heuft Hlan (Upgrade Optional) · Hayt two ways discharge Delta K to the right · 4 Variety Licenses · Tripartite Delta K for band height of 1130 · Two fluids for lye detection Not available! · inlet control, must be supplemented if necessary · Thread edging, must be supplemented if required · The documentation is complet ...
used
PET Empty Bottle Inspector HEUFT InLine TI 60 BFS2-r Device No. 2SG021663 Built: / year of construction: 2006 Output[B/h]: / performance [cont./h]: 36,000 Flow direction of: / moving direction from: Direction: / rejection direction: Installation location: / installation site: In front of the filler • Basic unit: Empty bottle inspector • Inspection: 1.Soil-IN-r • Inspection: Estuary IN-r • Inspection: 1st sidewall IN-r • Inspection: 2nd sidewall IN-r • Inspection: SW double resolution-r • Inspection: Carrying ring/PET-r • Inspection: RefPet abrasion-r • Inspection: RefPet Ventslot-r • Inspection: Stress crack detection-r • Accessories Transport belt: Height adjustable • Residual fluid detection: IR • Height adjustment: for discharge • Cross-adjustment: for discharge • Discharge ...
new
Semi-automatic induction sealer for aluminium foils in closures - Closure sizes 15-60mm - Closure sizes 50-120mm
used
Inv. Num: 5345 Type: Insert 330H 90 Producer: Engel Generated: 2006 Parameters: Clamping force: 340 t Injection capacity: 113 cm3 Screw diameter: 30 mm Facilities: Turntable
used
Top machine! This machine puts inserts into envelopes Inserter stations (2) safety features double-/missing sheet detection air suckers feed from bottom of pile envelope counter Insert dims 156x244 to 84x114mm envelope dims max 156x244mm min 89x171mm working speed up to 10.000 envelopes/hr variable speed adjustement
used
Code: 0555 Brand: STEMA 2 BR Model: INSERMATIC CB/86 - CE Standard Drilling and inserting machine for furniture hinges , kitchens, cabinets, furniture in general - CE Standard Technical data: Drilling unit: Electropneumatic unit with motor Hp 2- 3000 rpm - Works from bottom to top, from under the panel - Drilling head: 3 spindles for hinges - 2 spindles for mounting plates Hinge insertion unit: N°1 single loader Worktable: rubber-coated rollers width 500 mm N° 6 mechanical stop blocks Suction 1 mouth diameter mm 80 Panel clamping: N° 2 vertical pressers Volt 380/50 Compressed air 6 atm Overall dimensions: mm 3600 x 1300 x 1300 h Weight kg 530
used
internal diameter: 340/440 mm grinding depth: 9999999999999999999999999 mm swing diameter: mm grinding diameter: 250,350,450 mm grinding length: 600 mm centre height: 125,175,225 mm bore: 127 mm : MK5 work piece spindle speed: 20-400 U/min workpiece spindle - bore: mm grinding head swivelling: 360 ° grinding spindle head - swivable: 180 + - ° grinding spindle speed: 1500,1700,2200 U/min : 0,001-0,030 mm/Ø : 0-0,95 mm/Ø : ±10 ° longitudinal feed of the table: 900 mm table speeds: 0,02-6 m/min : 130 kg : 130 inkl. Spannugkg kg : mm : 70 mm total power requirement: 6,5 kW weight of the machine ca.: 2,2 t dimensions of the machine ca.: 3,1 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your machines.geometrical overh ...
used
screw size: unbkt mm injection shot weight in Polysterol: unbkt g/PS closing pressure: 100 kN total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
Hives inserter – APE Year: 1997. Speed: 4.000 bph. Direction: Linear. Model: INSER 2000. Double head. Safety protections. Including vibrating Conveyor
used
Hives inserter | MONDO&SCAGLIONE Year: 2000 Speed: 10.000 bph Safety protections
used
Hives inserter APE | Double head Year: 2001 Speed: 6.000 bph Direction: Clockwise Model: INSER 1200 Safety protections
used
For sale is a used, well-preserved Infusomat fm from B/BRAUN with drop sensor, device holder, power cable and new battery PCS 9/23 You will receive a VAT invoice.
used
Fresenius MCM 550 ST Infusomat with drop sensor valid STK Ready for immediate use You will receive a VAT invoice.
used
Fresenius Injectomat cp-PS functional You will receive a VAT invoice.
used
Screw diameter: 30 mm Displacement: 74 cm³Injection weight in polystyrene: 66 g/hp Injection pressure: 2,020 bar Clamping force: 50 t Lights tie bar distance H x V: 420 x 370 mm Tool installation height min.: 200 mm Opening distance: 340 mm CONTROL: NC4 Screen text: german / english Operating instructions: german / english FHK interface for robots: Yes Core pull: 1x Pump drive power: --- Total connection load: 33 kW Total weight: 4,750 kg Dimensions L x W x H: 4.3 x 1.1 x 2.0 m m m m Terms of payment: 100 % before taking over the machine, strictly net
used
Linco inside / outside washing machine of 16 units C.W. Unique in design , this machine has been developed by Linco to out-perform and surpass all the other machines available. Special adjustable nylon / stainless nozzles enter the bird to ensure thorough inside washing, no possible damage, and a positive opening in the neck cavity of the bird to ensure drainage. Water sprays on the outside of the bird remove any debris or stains left after eviscerating.
used
ENGEL INSERT 60H/30 SHUTTLE injection moulding machine was manufactured in 2016 in Austria. A specialised machine with a small footprint, is used for, among others, the overmoulding of inserts and the joining of various materials such as glass, metal and electronics. Thanks to the electric control of the injection unit and the ‘pressure locking’ system for the injection cylinders, the injection moulding machine guarantees high repeatability and excellent quality of inserts. The ENGEL INSERT 30 injection moulding machine allows you to set the speed and clamping force to prevent damage to the mould. Once both mould halves are closed and a high closing force is generated, the injection unit pushes the nozzle against the injection sleeve of the mould and produces an adjustable clamping force. At the end of the cycle, a very powerful screw with a diameter of 18 mm injects the melt unde ...
used
ENGEL INSERT 200H/50 injection moulding machine was manufactured in 2007 in Austria. The machine with its small size and large capabilities is used for e.g. overmoulding of inserts and the joining of various materials such as glass, metal and electronics. Thanks to the combination of a clamping force of 50 tonnes and high-quality components, the injection moulding machine guarantees excellent quality of inserts and high repeatability. The machine’s sturdy, solidly built construction features a convenient and easy-to-use ENGEL CC 200 CNC controller for entering all possible process parameters, such as mould clamping force and speed. Once the parameters have been entered, the two halves of the mould are precisely closed, after which the vertical injection moulding machine ENGEL generates a high clamping force. The mould cavity is carefully filled with plastic under high pressure using ...
used
Offer: Engel Insert 500V/100 LIM Bj./year 2014 approx. 8000h
used
Digital input module 16x24V DC 3ms PS416-INP-400 -Supply voltage at: DC 24...24V -Type of voltage of the supply voltage: DC -Number of digital inputs: 16 -Number of digital outputs: 0 -Input current for signal: 1 8.6mA -Allowable voltage at the input: -3...30.2V -Type of input voltage: DC -Type of digital output: none -Allowable voltage at the output: 0V -Design of the electrical connection: plug connection -Delay time for signal change: 3...3ms -Explosion protection category: PS416-INP-400 -Weight: 0.2 kg
used
Inductive sensor, electronics sensor -M50 x 1.5 -Type: IN 50 60 40 -Number: 2x available -Price: per piece -Weight: 300 g
used
Technotrans TBP 300-36/12 Ink Supply System Ink supply System for Sheetfed Offset Age: 2004 4x Ink Pumps 10x ink trac L900 ink levelling and control system for the central fully automated filling of ink ducts. Supply System was in use on a KBA 105 machine
used
Inductive sensor, electronics sensor -Manufacturer: IFM -Product type: IN5129 IN-3004-BPKG -Number: 2x available -Price: per piece -Weight: 0.2 kg
used
Inductive sensor, electronic sensor, safety switch, inductive proximity switch -Manufacturer: efector, inductive sensor proximity switch unused original packaging -Product Type: IN-3004-BPKG / IN5129 -Number: 1x sensor available -Price per piece -Dimensions cardboard: 150/125/H30 mm -Weight: 0.1kg/carton
used
Internal micrometers, micrometer screw, internal diameter, internal precision measuring device, cylinder gauge, -Measuring range: 35-60mm -Dimensions: 115/450/H60 mm -Weight 1.6kg
used
This ENGEL insert 60V-35 single XS ecodrive Injection moulding machine was manufactured in the year 2017 in Austria and has 12750 production hours. It is equipped with an Engel CC300 control unit. The machine has a clamping force of 350 kN. 3 units are available.
used
Injection unit Screw diameter: 35 mm Closing unit Closing force : 1000 kN Distance between tie-bars: 520 x 520 mm Other Equipment : FULL ELECTRIC machine NC5 control Commissioning : 2010 Tonnage : 100
used
proximity switch -Manufacturer: IPF Electronic -Product type: IN 40 60 40 -Number: 37x available -Price: per piece -Weight: 300 g
used
Clamping force: 1600kN, weight: 9t, operational hours counter: 3638h, with Handling Robot ENGEL viper 20.
used
Clamping force: 200t, max. operating temperature: 400°C, clamping plate dimensions: 1020x605mm, min. tool installation height: 680mm, opening path: 400mm, max. tool weight: 3,2t, shot weight: 50- 600g, screw diameter: 55mm, L/D20, with 2x core puller hydraulic 1-fold, 2x core puller pneumatic, 1-fold mold temperature control, standard up to 90°C, an on-site inspection is possible.
used
Output: 24,000/h, band speed: 0.5m/s, format: 0.25l GASTRO/ 0.5l GASTRO/ 0.7l GBD/ 0.75l GBD, GASTRO, with Sorting System HEUFT SPECTRUM SX TI 36, machines were overhauled in October 2021.
used
Output: 36,000 bottles/h, format: NRW white/ GDB 0.7l/ GDB 0.75l green/ Longneck 0.33l KK/ 1.0l Individual, with spare parts, double side wall, thread, neck finish, 2x residual liquid, base and automatic test bottle request, has been serviced regularly, inspection is possiblem, but not under power.
used
With documentation and pusher, has been regularly serviced, operating hours: 23,476h, the machine has already been dismantled.
used
For sale are 3 Sumitomo Demag IntElect 150/520-410 injection molding machines in good technical condition, complete with hydraulic stations, Witmann Battenfeld W-721 robots (3 axes) and robot work area fences. Stored in a heated room. Unfortunately, there is no way to see the operating time, because... The injection molding machines are not connected to the power supply. Clamping unit 1500. Closing force 1500 kN, holding force 1650 kN, opening stroke max. 495 mm, built-in mold height min/max 275/585 mm, max. the distance between the plates for clamping the mold is 1080 mm, the plates for clamping the molds are 770x770 mm, the clearance between the columns is 520x520 mm, the weight of the mold is max. 1700 kg, which makes the weight of the mold on the movable clamping plate 1150 kg. Ejector. ejector stroke - 125 mm, ejection force 35 kN, ejector return force - 35 kN Injection unit 41 ...
used
The injection molding machine is in good working order, sold due to the completion of the project. If necessary, it can be seen in operation. Clamping force: 340 t Injection capacity: 113 cm³ Screw diameter: 30 mm Equipment: Turntable
used
Description 13 zone mold heating working hours: 3447
used
Mazak Integrex 200-IV ST Ø 660 x 1500 mm Control Unit: Mazatrol Matrix Maximum turning diameter : 660/260 mm Maximum turning length : 1.495 mm Milling spindle speed : 12.000 rpm Main spindle maximum speed : 5000 rpm Subspindle maximum speed : 5000 rpm ATC 40 Capto C6 system 9-station turret swarf conveyor 2 Stck. 3-jawchuck Kitagawa B-208 5-axis simultaneous Full C-axis sub spindle Flash-Tool Synch. MillTapp Gear Hobbing CE-Zeichen Come with tools purchased
used
Key data: 900 kN, 140 g/PS, 35 mm
Year of construction: 2006 Clamping force: 90 tons. Screw diameter: 35 mm Pump hours: 46393 h
used
Key data: 350 kN, 18 mm
Manufacturer: ENGEL, type Insert Insert 80H/35 Construction: Rotary table Clamping force: 35 t Year of manufacture: 2011 - neat condition, maintained, no oil leakage. Commissioning: 23.11.2011 Hours: 36,077 hours Injection unit: 18 mm Control: CC200
used
Bluhm Systems Markoprint Integra One Printing System Markoprint Integra One with HP cartridge technology. The system, with its small dimensions of 188 x 80 x 98 mm, can be easily installed in or on production equipment. The print head reaches top speeds of more than 180 m/min and has an IP-65 protection class. The printing system is equipped with a display for data entry as well as changing and checking system settings. Operators can check or change variable print information and settings directly on site on the user-friendly display. Intuitive control is provided by an i-Logic button. In addition, maintenance statuses can be shown on the display. With dimensions of 188 x 80 x 98 mm, the Integra One is particularly compact and has been specially developed for system integration. Smart cartridge monitoring Intelligent SmartCard cartridge monitoring identifies the curr ...
used
For sale is a used, well-preserved Infusomat P from B.BRAUN with drop sensor, power cord and device holder. valid MTK 9/24
used
Indexable insert drills, high performance drills with indexable inserts, solid drills, end mills, end mills, milling cutters, indexable insert mills, end mills with internal cooling, indexable insert end mills -Handover: in current condition as seen -Reversible plate: 1 piece missing -Finger milling cutter: indexable insert end mill with internal cooling -Receptacle: Ø 30 mm -Diameter: 16mm -Dimension: 133/40/H40 mm -Weight: 0.4kg
used
Indexable insert drills, high performance drills with indexable inserts, solid drills, end mills, end mills, milling cutters, indexable insert mills, end mills with internal cooling, indexable insert end mills -Finger milling cutters: indexable insert end mills with internal cooling, 8 pieces -Receptacle: Ø 32 mm -Diameter: 32 to 43 mm, see photos / parts list -Levy/Price: complete -Transport dimensions: 400/200/H60 mm -Weight: 8.7kg
used
Indexable insert drills, high performance drills with indexable inserts, solid drills, end mills, end mills, milling cutters, indexable insert mills, end mills with internal cooling, indexable insert end mills -Finger milling cutter: indexable insert end mill with internal cooling, 2 pieces -Receptacle: Ø 40 mm -Diameter: 29 and 45 mm / 1x with 1x without indexable plates -Levy/Price: complete -Transport dimensions: 240/100/H50 mm -Total weight: 2.9 kg
used
Indexable insert drills, high performance drills with indexable inserts, solid drills, end mills, end mills, milling cutters, indexable insert mills, end mills with internal cooling, indexable insert end mills -Finger milling cutter: indexable insert end mill with internal cooling, 2 pieces -Receptacle: Ø 25 mm -Diameter: 25 and 30 mm -Levy/Price: complete -Transport dimensions: 210/70/H40 mm -Weight: 1.0kg