machine forging used for sale

Nominal mass of falling parts, taking into account the mass of the upper stamp (500 kg.), Kg. 5000 Actual mass of falling parts without top stamp, kg. 5030 Effective kinetic energy of falling parts at full successive impacts, kgc m 12500 The greatest working stroke of a woman, mm. 1300 The smallest height of dies without shanks, mm. 400 Distance between guides in the light, mm. 800 The length of the woman in the direction perpendicular to the front of the hammer, mm. 1180 Steam (air) pressure before entering the cylinder, atm. 7-9 Nominal mass of the upper die, kg 500 The largest mass of the upper die, kg. 1500 The highest permissible steam temperature, ⁰C 200 weight 145-148ton, weight of anvil block 75+22 ton.

Capacity :10 tons, Weight of falling part,nominal mass of drop parts without upper instr.:9 tons, Effective working kinetic energy after blow :25000 kg mtr., Max. working ram stroke :1400 mm, Max no of blows : 30/min , Distance between slides : 1000 mm, Shut height : 775 mm , Ram size front to back :1200 mm, Bolster size front to back :1200 mm, Air pressure : 7-9 MPA , Height of instruments : 450 min., Die-holder front to back dimensions: 1400 mm, Height above floor level: 7270 mm, Hammer dimensions : 4400x10420x2700 mm, Weight (less anvil block): 73.5 ton, Weight of anvil block : 203.8 tons.

Offer 04446 Specifications: - Total width approx. 950 mm - Working surface length / web length approx. 420 mm - Working surface depth / web depth approx. 150 mm - Compression foot approx. W 120 x D 125 x H 140 mm - Total depth approx. 280 mm - Round horn approx. 250 mm - Square horn approx. 260 mm - Round hole in the track approx. 22 mm - Through-square hole in the track approx. 25 mm - Anvil height approx. 345 mm - Weight approx. 190 kg - Base frame W 520 x D 520 x H 345 mm - Weight 30 kg

Nominal weight of the falling parts: 750 kg Max. number of blows per minute: 105 Kinetic energy: 1900 kg Distance from an axis of the slider up to bed: 750 mm Cylinder diameter: 600 mm Diameter of the plunger: 630 mm Max. headstock travel: 835 mm Dimensions: -Left-to-right: 3940 mm -Front-to-back: 1430 mm Height above floor level: 3260 mm Weight: -With an anvil-block: 25600 kg -Without an anvil-block: 16600 kg

2000 Ton Sumitomo Hot Forging Press line Year 2006 Stroke 350 mm (13.78") Strokes per min 75 Shut height 850 mm (33.47") SlideAdj. 7 mm (.27") Ram size 1200 mm LR X 1300 mm FB Bed size 1320 mm LR X 1300 mm FB 4 stage transfer system Slide knockout Bottom knockout Scrap System Dual Die Changer Extra Die Shoes Billet Heater and Billet Saw Also Available This line was used by HONDA to make transmission gears, It takes a billet, cuts it to size, heats it to 1300 C then the press hits it 4 times. It can determine good from bad parts, the bad parts get sent to a quench tank, the good parts get sent into a cool down conveyor that you can pick the parts up by hand at the end. The entire system was ran by one operator.

Specifications: - Total width approx. 800 mm - Work surface length / web length approx. 120 mm - Working surface depth / web depth approx. 120 mm - Total depth approx. 100 mm - Round horn approx. 340 mm - Square horn approx. 340 mm - Anvil height with substructure approx. 820 mm - Anvil weight approx. 65 kg - Substructure approx. W 420 x D 420 x H 300 mm - Substructure mounting hole 85 mm - Weight of substructure approx. 35 kg

Eccentric shaft for hot forging press K8548 6300T Weight, kg 27 800

Drive gear for hot forging press K8548 6300T Weight, kg 15 700

Driven gear for hot forging press 6300T Weight, kg 1300

Clutch hub for hot forging press K8548 6300T Weight, kg 7100

6500ton Open Die Forging Press HJ / Seonam (Korea) Design: Eastern European Corporation Installation: 2006/2008 Press Type: Four column push down Oil hydraulic system Nominal force (static working pressure of 320 bar): 5,000 Tons Up-setting force (static working pressure of 420 bar): 6500 Tons Daylight: 5,200 mm Stroke of Movable cross head: 2,700 mm Main Ram dia. (Center cylinder): 1 set - ￠950 mm Side Ram dia. (Side cylinder): 2 sets - ￠750 mm Return cylinder Ram dia: 2 sets - ￠300 mm Moving Table Width: 2,600×Length 6,600 mm Moving Table stroke (center to both side 2,750mm): 5,500 mm Approaching speed: 300 mm/sec Main cylinder Forging speed (2,200 tons/ 320 bar): 163 mm/sec All cylinder Forging speed (5,000 tons/ 320 bar): 73 mm/sec Up-setting Forging speed (6,500 tons/ 420 bar): 10 mm/sec Return speed: 270 mm/sec Hydraulic Main pump: 12 sets  ...

Nominal force 1250 ton - first stage : 260 tons, - second stage : 800 tons, - third stage : 1250 tons, Slide stroke 1250 mm Distance between table and slide 2650 mm Main cylinder dia Ø 500mm Return cylinder dia. ( two) 2xØ400mm Distance between column 1800mm Table size width / length 1250 / 3150 mm Main motor power 150 kW Machine dimensions L x W x H 16950 x 12100 x 11410 mm Weight 265000 kg Forging manipulator FS2ЕТС -2T also available 1T and 700t

for production of forgings by forging of ferrous, non-ferrous metals and alloys in the hammer dies model M212 Impact energy, 50 kJ Nominal weight of falling parts, kg 2000 Stroke woman, mm 1200 Stroke woman, mm 1200 Machine dimensions Length Width Height (mm) 3650X1660X5310 Weight kg 58.310, spare parts available

pressure: 1645 t stroke: 1000 mm dayligth: 3000 mm Control: down speed: 280 mm/sec return speed: 275/346 mm/sec distance between columns: 2520 mm total power requirement: kW weight of the machine ca.: t the machine is in very good condition optional you can buy a shifting table as well The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Complete Mechanical Upgrade by GFM, with increase of Power to 900 Ton/hammer and new CNC in 1991 Numbers ̈of Hammers: 4 Forging force: 3.600 Ton (900t per hammer) Strokes per minute: 270 Maximum diameter of forging: - circular cross section: Ø 400 mm - square cross section: 320 mm Minimum output diameter: - circular: 60 mm - square: approx 50 mm Maximum length of forging with/without lateral reception: 8.000 mm / 9.700 mm Feed of manipulator A: 7.140 mm Feed of manipulator B: 9.940 mm Workpìece weight: 2500 kg Total power supply (nominal power): ca 1.600 kW Machine weight: 493.000 kg

Key data: 150 kg, 480 mm, 375 mm

Hammer weight: 150 kg Stroke length: 480 mm Stroke rate: 168 p/min. Projection: 375 mm Plunger diameter: 180 mm Origin: England Motor power: 11 kW Machine LxWxH: 200 x 180 x 240 cm Machine Weight: 6000 kg

Capacity: 1600 tons Slide stroke: 300 mm Slide stroke length at maximum force: 0,16 mm Distance adjustment between tableand slider: 10 mm Slide stroke number in 1 min: 75 Length of a rod: 920 mm The closed height: 660 mm Table overall dimensions: 940x1200 mm Table height above floor level: 450 mm Slide overall dimensions: 860x910 mm The size of lateral windows: -Height: 560 E5931468 mm -Width: 600 mm Main motor: 110 kW Press overall dimensions: -Length: 5060 mm -Width: 3940 mm -Height above floor level: 5125 mm Press weight: 120 tons

Nominal weight of the falling parts: 750 kg Max. number of blows per minute: 105 Kinetic energy: 1900 kg Distance from an axis of the slider up to bed: 750 mm Cylinder diameter: 600 mm Diameter of the plunger: 630 mm Max. headstock travel: 835 mm Dimensions: -Left-to-right: 3940 mm -Front-to-back: 1430 mm Height above floor level: 3260 mm Weight: -With an anvil-block: 25600 kg -Without an anvil-block: 16600 kg

Offer 25443 Specifications: - Bear weight 40 kg - Impact regulation - Lifting height infinitely adjustable 200 mm - Impact rate approx. 220 1/min - Projection 280 mm - Anvil - height approx. 560 mm - Anvil - Weight 250 kg - Drive 380 V / 4 kW - Space requirement approx. W 850 x H 1100 x D 1350 mm - Weight approx. 850 kg

Air steam die forging hammer : Capacity : 16 tons, Nominal mass of drop parts : 16000 kg, Impact energy : 400 KJ, Ram stroke : 1500 mm, Ram stroke per minute : 20, Distance clear between guides : 1180 mm, Ram dimensions front to back : 1500 mm, Die holder dimensions front to back : 1600 mm, Bottom die impression to floor distance : 500 mm, Steam/air pressure : 0.7-0.9 MPa, Overal dimensions : - Floor space : 4500 x 2450 mm, - Height above floor level : 7920 mm, Mass of anvil block : 325 tons, Total weight of hammer : 425 tons.

400 Ton Hydromec HF4000 Non-Ferrous Hot Forging Press Line MANUFACTURER – HYDROMEC YEAR – 2000 SERIAL NUMBER – 660 MODEL – HF4000 C/D MATERIAL – NON-FERROUS TONNAGE – 400 TON (4000 KN) STROKE – 380MM STROKE PER MINUTE (CONTINUOUS) – 22-35 STROKE PER MINUTE (SINGLE STROKE) – 22-45 RAM ADJUSTMENT RANGE – 100MM CLEARANCE (STROKE TO BOTTOM, ADJUSTMENT TO TOP) – 865MM SIZE OF TOOL MOUNTING PLATE – 1000MM X 1000MM MAIN PRESS MOTOR – 59 KW MAIN MOTOR RAM ADJUSTMENT – 2.2 KW CUSHION FORCE – 70 TON (700 KN) CUSHION STROKE – 40 – 110MM INCLUDES: AUTOMATED PICK AND PLACE ROBOT FULLY AUTOMATED SLUG LOADING STATION WITH FURNACE/CONVEYANCE MAESTRI C.T. 3500 4 TRACKS SLUG FURNACE (NEW 2000) , 420 KW POWER. NATURAL GAS, 950 DEGREES CELCIUS ELECTRICS PRESS CONTROLS VIRTUAL WALK Combination Lot of the following: Lot No. O233 MAESTRI Gas  ...

Capacity: 1600 tons Slide stroke: 300 mm Slide stroke length at maximum force: 0,16 mm Distance adjustment between table and slider: 10 mm Slide stroke number in 1 min: 75 Length of a rod: 920 mm The closed height: 660 mm Table overall dimensions: 940x1200 mm Table height above floor level: 450 mm Slide overall dimensions: 860x910 mm The size of lateral windows: -Height: 560 mm -Width: 600 mm Main motor: 110 kW Press overall dimensions: -Length: 5060 mm -Width: 3940 mm -Height above floor level: 5125 mm Press weight: 120 tons

Capacity 7.25T /16000lbs Stroke 1727 mm weight 270t

Capacity 5.4T /12000 lbs Stroke 1626 mm weight 150t

Capacity 2.7T /6000 lbs. Stroke 1403 mm weight 77.5t

LASCO FP 222 S hydraulic press was built in Germany by Lasco Umformtechnik GmbH. The machine has been continuously maintained and upgraded throughout its service life. In 2022, a major upgrade was carried out, which included replacing the electrical cabinet, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The LASCO FP 222 S is an extremely versatile hydraulic press designed for the production of extremely precise, repeatable and yet complex components used in the broadly defined automotive or machinery industry. Its main application is hot and cold forging. The use of a die cushio in the lower work table and the large slider stroke means that the machine can also be used as a deep drawing press. All machining processes are performed with a high press force of up to 200 tonnes, which, combined with the highly dynamic slider, guarantees the b ...

LASCO TSP 160 S forging press was built in Germany by Langenstein & Schemann A.G. (Lasco Umformtechnik GmbH). The machine has been continuously maintained and upgraded throughout its service life. In 2019, a major upgrade was carried out, which included replacing the seals, upgrading the control system, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The LASCO TSP 160 S is an extremely versatile hydraulic press designed for the production of extremely precise, repeatable and yet complex parts. It is ideal for forges and industrial plants that require high press forces and high repeatability of the manufactured parts. Its main purpose is die forging, metal stamping and metal forming, especially hot forming of steel or aluminium workpieces. It also enables punching, calibration of forgings, trimming and blanking of workpieces after the forgin ...

nominal force:2500 t stroke:600 mm cycle time:13 - 18 s distance between columns:1720 mm Distance table/ram, max. stroke up, adjustment up:2600 mm table surface area:1720 x 1800 mm allowed max. force:4000 t blow die to die:5000 t ram surface:2100 x 1320 mm capacity of ejector in table:40 t ejector stroke in table:250 mm ejector surface area in table:900 x 820 mm capacity of ejector in ram:6 t ejector stroke in ram:40 mm spindle diameter:425 mm power requirement:900,0 kW weight:335,0 t Dimensions (WxDxH):3,4 x 4,6 x 9,7 m height over floor:8,3 m fully-automated forging line:to produce axle shaft

impact energy:207951 mkg ram hammer stroke:660 mm no. of strokes:100 /min impact energy:2040 kJ distance lower die block / ram gudeway:660 mm Throat:750 mm steel forging - rectangular up to:240 mm steel forging - diameter up to:270 mm power requirement:75,0 kW weight of hammer:16,5 t weight of anvil:15,5 t ram hammer weight:750 kg weight:32,0 t dimensions (WxDxH):3,2 x 1,45 x 3,45 m Mode of operation:pneumatisch

TIG Welding Machine, Electric Welding Machine KESTRA Type TIG 350 AC/DCE Welding MachineFabr. No. 09720693 Year of construction approx. 1985Power 350 Amp. = 60 % EDExsetting range 3 steps and fine adjustmentCurrent type AC / DCNet connection 400 volts, 50 Hz, 32 Amp. Plug- 4 meter hose package with TIG torch- 2 stroke / 4 stroke welding device- Water-cooled- Gas pressure reducing valveSpace requirement L x W x H 1050 x 560 x 900 mmWeight 250 kgThe welding test gives good results when welding stainless steel with

TIG welding machine, electric welding machine DALEX type TGKW 55 (AC-DC)Series No. 532521 year of construction approx. 1975Power 225 Amp. = 60 % ED 125 Amp. = 100 % EDEsetting range 2.8 to 225 ampereCurrent type direct current and alternating current (AC-DC)Mains connection 380 volts, 50 Hz- Power setting via 5 coarse steps and fine adjustment via rotary potentiometer infinitely variable- 2-stroke and 4-stroke welding device- Remote controller with rotary potentiometer for fine adjustment- Digital display for ampere- TIG hose package 4 meters- Welding gas pressure reducing valve-

Quantum Qsm 175 Double Grinder Grinding Machine Double Grinding Machine Auction-ID: A7-45427-243

PADE model 1000/N trimming-milling-drilling machine: – automatic sliding worktop – blade for header D=400mm, 3 hp motor – milling machine with shaft D=30mm, 5 hp motor – 5-spindle drilling machine, 360° adjustable, 3 HP motor Machine not CE compliant, for export

Specifications / Technical Data S-1000 CNC-Fraese and Engraving Machine The almost largest CNC machine in the High-Z series. With an external dimension of approx. 1350 x 800mm still handy enough and extremely powerful. With the High-Z CNC unit, they acquire an all-round talent in TUeV-certified quality (EMC). Whether you want to clamp complex parts on a groove table or, or to clamp factory tins into a high vice (the machine is on a frame construction, is driven in X via 2 motors and thus allows to be placed completely over a part to be machined). or simply want to do engraving or drilling then they simply work on a flat base, on which they then attach e.g. an MDF plate, which they once overfrave plan and are then able to work up to approx. +-0.02mm exactly in depth. All CNC portal fraes machines are supplied with coloured energy chains on all axes due to the improved cable guid ...

Carrier bag machine / SOS block bottom bag machine with flat inside handle unit Bag width: 14-32cm Tube length: 35-70cm Bottom width: 6-20cm Reel width: 107cm max Hot Melt unit for handles Web guide system for handles Foto cell unit for preprinted paper Aprox 7 former plates Option: 4 colour tail end printer (ref. S294)

Motor power: 1,5 kW. Max. mortise width: 180 mm. Max. mortise depth: 180 mm. Chain width: 2x10 mm. Machine dimensions: 600x950x1900 mm. Weight: ~200 kg.

A good sample preparation in metallography (materialography) starts at the correct separation with a wett cutting machine. Good and proper separation prevents the burning and destruction of the material change in its structure and is the best way to save time and consumables. The separation is performed incorrectly is this very elaborate grinding and polishing extremely high overhead "punished"! Wet cutting machine cutting. Wet abrasive cutting | Separating SCHNEIDER METACUT 251 The head of the cutting grinding machine with built-in blade is lowered by a hand lever on the sample. METACUT 251 separating cutters are available exclusively in manual versions. This is usually not a disadvantage: the specimen geometry changes / separation task all the time, so can hinder the establishment of an automatic cut-off grinder. The workpiece is clamped at METACUT 251 - cut-off machines and the de ...

FORCIPOL - the quality grinding machine / polishing machine for metalography that is cheap on the market - from the simple grinding machine for manual preparation to the semi-automatic machine - The FORCIPOL series is modular and can be assembled as required FORCIPOL 102: Basic grinding machine / polishing machine with a grinding wheel 250 mm and basic control FORCIPOL 202: as before, but 2 grinding wheels 250 mm For rationalization and reproducible cuts (can be combined with FORCIPOL 102 or 202): FORCIMAT 52: Sample wineer head with simple control FORCIMAT 102: Sample winer head with programmable control For the supply of lubricants and suspensions (only IN the case of FORCIMAT 52 / 102) DOSIMAT 12 - Lubricant Dosing Device DOSIMAT 52 - Lubricant and suspension dispenser (adjust integrated internal control on the device) DOSIMAT 102 - Lubricant and suspension dispenser  ...

Copying fraes machine Kuhlmann Type GM 1-2 Machine in very good condition. Optional: very extensive access at an additional cost Zubehoer s/he/sheers, milling spindles, sub-machines for circular copying, written fonts, fraesstichel with quick-change device, copy spin, Radient template for radii in 0.5mm rising, clamping devices, Stencils and much more! Special price Tool cabinets milling spindle spindle grasses engraving fonts brass copper table

Kettenstemmer GF L x W x H: 120 x 70 x 270 cm Weight 570 kg Baeqvhtqms Year of construction 1983 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Pot discs - diameter:175 mm spindle extension:180 mm operating voltage:400 V Machine weight approx.:300 kg room requirements approx.:0.90 x 0.60 x 1.80 m

La San Marco NEW 105 MULTIBOILER 2G portafilter machine Original price 8.800 ,- € In the NEW 105 Multiboiler series, the latest technology from La San Marco has been applied. Multiboiler technology allows precise temperature control for each boiler of each individual group. The temperature is set in a simple and intuitive way on the keyboard of each group. The boiler for steam and hot water has an electronic automatic temperature adjustment, which can be easily adjusted using the touchscreen keyboard. The innovative keyboard with touchscreen technology is complemented by a graphic RGB display. Setup and program advice is simple and intuitive, and the display also provides a range of information that is of great benefit to the operator. The illumination of the workstation with customizable multicolor LED makes the machine even more ergonomic with an eye on aesthetics. Grou ...

Carrier bag machine, SOS block bottom bag machine with flat inside handle unit Photo cell 4 colour tail end printer Bottom patch Bag with handles: Bag width: 20-32 cm Tube length: 33-66 cm Bottom width: 7-18 cm Bag without handles: Bag width: 16-32 cm Tube length: 24-90 cm Bottom width: 7-18 cm

Combi with 11.1.073 Novopac Shrink tunnel Remaining: 3 parts Chassis number: 4395905 Weight: 1,0 tons Power: 4 kW Air pressure: 7 bar L x w x h first part: 2600 x 1700 x 2000 L x w x h second part: 3200 x 2400 x 1700 L x w x h third part: 1775 x 3300 x 1500 Working height: 85 cm. Transport size L x W x H: 2,6 x 1,7 x 2,0 + 3,2 x 2,4 x 1,7 + 1,775 x 3,3 x 1,5 Min.-max. glass thickness: Max 300 mm Min.-max glass size: Max 1460 mm width Condition machine : Repaired after malfunction Control type: Automatic Electric. Connection: 400V Documentation: Available Instructions: Available Electric diagram: Available Parts list: No Remaining: Combi with no. 23073 Photos/film available: Photo's available

The servoCUT 402 / 502 / 602 cutting machines is designed as a wet cutting grinding machine for cutting large / small / regularly / irregularly shaped workpieces made of metal ceramic or material compositions. Thanks to the modern joystick control, the separation process can start after just a few seconds: position the test piece clamping, the cutting disc with joystick in a hurry, press START and leave the machines (unmanned). Depending on the version available as a fully automatic version (X-Y-Z axes motorized) or manual axle delivery. The ideal equipment for all applications - enormously flexible, ergonomic operation with quick start, suitable for the smallest workpieces but also for long test pieces (driving cut) - the ideal solution for the professional (service provider in material testing, contract hardening, ...) and for difficult materials (pulse cutting, etc.) The SERV ...

The SERVOCUT 602 cutting machine is designed as a wet cutting grinder for cutting large / small / regularly / irregularly shaped workpieces made of metal ceramics or material compositions. Thanks to the modern joystick control, the separation process can start after just a few seconds: position the test piece clamping, the cutting disc with joystick in a hurry, press START and leave the machines (unmanned). Depending on the version available as a fully automatic version (X-Y-Z axes motorized) or manual axle delivery. The ideal equipment for all applications - enormously flexible, ergonomic operation with quick start, suitable for the smallest workpieces but also for long test pieces (driving cut) - the ideal solution for the professional (service provider in material testing, contract hardening, ...) and for difficult materials (pulse cutting, etc.) The SERVOCUT cutting machines ...

Attention: Before purchasing a used universal tester / tractor, consider the old, used machine (all?) need new electronics for WIN 10. No manufacturer / Microsoft provides support for WIN XP / 7 – an expensive impasse! Purchase, pickup, software update (if possible?), commissioning, modernization are more expensive than a new galDABINI machine Quasar 600 kN incl. load cell 600 kN, Latest technology (BECKHOFF Elektronik) with first-class software LabTest. Suitable for tensile tests, pressure tests, bending tests and cyclic tests stable, using finite elements FEM, 2-line universal test era Optional load cells N: 10 | 20 | 50 | 100 | 250 | 500 or kN 1 | 2.5 | 5 | 10 | 25 | 50 | 100 | 200 | 250 for tests on steel, reinforced steel, plastic, rubber, foils, textiles, wire, sheet metal, components, assemblies and many more. Very well Made in Italy | Europe, German + European Q ...

TECHNICAL DATA: Max oscillation length mm: 100 Max depth of slots mm: 80 Spindle center distance min mm: 84 / max 1170 Spindle rotation rpm: 6.000 / 12.000 Processing: double sided Weight Kg: 2250

TECHNICAL DATA: Clamping height max mm: 1040 Tenoning depth max mm: 150 Slot length max mm: 340 Main motor power HP: 3 Weight Kg: 340