127,247 used machines on RESALE, but how to find them? Machine Search
- Exhaust manifold exhaust manifold MWM 12300010 - Suitable for several motors - Please note! Price per piece! - References -> 12300011 The Onets Group, including KompoTec in Cologne, is available as an experienced partner for the overhaul of gas engines. Our extensive range of services ranges from the basic refurbishment of stationary gas engines and their components to repairs in line with current value. In addition, we offer rapid provision of replacement engines as well as the production of individual and small series of new units. We support service providers, plant manufacturers and operators in the field of combined heat and power plants (CHP) and combined heat and power (CHP) in a partnership-based, technically convincing and sustainable manner. Our extensive experience in engine repair, resulting from decades of serial production, flows into every new project. By consta ...
Type FZ-515 Thickness of panel 10-60 mm Edging thickness 0,4-3 mm Feeding speed 15 m/min Air pressure 0,8 MPa Total install power 6,5 kW Panel width ? 60mm Transport dimensions 3700x900x1700 mm Weight 1200 kg
Machine type MIG/MAG inverter welding system Make Merkle Type MobiMIG 320 K Plant No. 118.362 Connection voltage 3 x 400 volts Setting range 25 - 320 amperes Switch-on time 40% ED at 300 amperes 60% ED at 270 amperes 100% ED at 240 amperes Current setting infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Design portable assembly system Wire feed gearbox 4-wheel gearbox DV 26 Hedging 16 Ampere Dimensions L x W x H 600 x 300 x 565 mm Weight 32 kg Age 6 months Condition workshop-tested new incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer argon with 2 pressure meters 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 pie ...
Type MM2617 Sand Pad Size 3120170mm Sanding belt line speed 18m/s Working table angle 45 ? Working table size 1200240mm2 Motor 4 kW
Manual Heating Press Reitz MHSP5H - Manual Lifting Screw Press Static Press Force 5 KN (0.5 to) - Portable press frame made of polyamide PA 6G - Manual screw jack with spindle 20 mm, pitch 5 mm - With handwheel diameter 120 mm and handle - Gear reduction ratio 1 : 10, 0.5 mm spindle travel per handwheel revolution, thus only very little hand force required for high pressure. - Table size 100150mm - Clear width 60 mm - Punch size diameter 70 mm with 4 holes 8 mm to attach the Hotplate - Very easy operation due to spindle and worm gear - Total weight approx. 25 kg With 2 electric aluminum heating plates 1200 watts, heating area approx. 150 100 mm to 250°C, connection 230 V. With sensor and temperature control. Pressure-resistant insulating panels at the top and bottom for use in presses. Suitable for pressing, welding and gluing.
Semi-automatic tube filling and sealing machine for PE, laminate and metal tubes, demonstration machine Capicity 10-20 tubes / min. Filling range from 5-250ml Tube sizes from D.13.5 - D.50mm with different format sets Ultrasonic sealing unit
Travel x 350 mm y 250 mm z 220 mm Water bath machine Automatic wire threading Glass scales x / y incl. box for large coils incl. cooler incl. functional guarantee
Unused solenoid valve for air intake from stock MWM 12072648
Twin Screw Extruder Metalchem 2T9/4,5 for PCV, Made by Metalchem out-put 100 kg/h
20-09-510 Edge Banding Machine WOODLAND MACHINERY (new) Type GB/T10850 Engine power 0.18 kW Air Pressure 3-6 Bar Voltage 220 V 50 Hz Total Power 1.4 kW Heating Capacity 1.2 kW Edge width 8-50 mm Edge thickness 0.3-3 mm Feed speed 0-26 cm/s Vacuum workpiece Attraction Transport Dimensions Weight 300 kg
English: Model: MB12 Bucket capacity - 0.022 m³ Chassis width - 930 mm Track length - 1200 mm Chassis ground clearance - 370 mm Gradeability - 30° Track width - 180 mm Tank volume - 5.5 L Transport length - 2870 mm Excavator height - 2285 mm Overall dimension - 2870 x 930 x 2285 mm Engine model - Koop 192F / Kubota D722 Engine power - 7.6 kW / 2400 rpm; 10.2 kW; 10 kW / 420 cc Turning radius - 1490 mm Max. digging height - 2490 mm Max. dumping height - 1745 mm Max. digging depth - 1725 mm Max. digging radius - 3030 mm Max. vertical digging depth - 1655 mm Bucket digging force - 6.5 kN Operating weight - 1200 kg All machines are new and come with a one-year warranty. Additional attachments such as rakes, augers, buckets, or grapples can be added to your order if needed. You can choose from a variety of engines that vary in size and power accor ...
English: The MB 10-B is our most compact and lightweight model—ideal for projects requiring maneuverability in tight urban spaces or residential backyards. With a sturdy build and precise controls, it's a favorite for small-scale landscaping and trenching. Despite its compact frame, it offers impressive digging force and a smooth, reliable experience. Technical Specifications Weight: 1000 kg Dimensions: 2870 x 930 x 2213 mm Standard Bucket Capacity: 0.022 cbm Engine: KOOP 192 / Briggs & Stratton Power Output: 11.7 hp / 8.6 kW or 13.5 hp / 10.07 kW Issue Rating: EURO V Displacement: 0.499 / 0.794 L Cooling Method: Air-cooled Max. Digging Depth: 1720 mm Bucket Digging Force: From 6.5 kN Hydraulics: Permco TJ Gradeability: 30°
Key data: 500 , 350 , 300
Travel X 500 / Y 350 / Z 300, Water bath machine, automatic wire threading, incl. 20 KG option incl. cooler
At the top of the line, the MB 20 is built for professionals who require serious performance. With the highest digging depth and force in the series, it's perfect for commercial applications. Its larger frame provides superior gradeability and traction, making it ideal for varied terrain and extended operations. Weight: 2000 kg Dimensions: 3110 x 1250 x 2280 mm Standard Bucket Capacity: 0.040 cbm Engine: Laidong 385 / Kubota D722 Power Output: 25 hp / 18 kW or 16.4 hp / 12.2 kW Issue Rating: EURO V Displacement: 1.617 / 0.719 L Cooling Method: Water-cooled Max. Digging Depth: 2050 mm Bucket Digging Force: From 10 kN Hydraulics: Permco TJ Gradeability: 35°
The MB 25 is where compact design meets elevated performance. With increased digging power and bucket capacity, this machine thrives in both urban projects and light commercial work. Its balanced weight and enhanced gradeability ensure stability and traction even on uneven terrain, while maintaining a compact form ideal for maneuvering in tight spaces. Weight: 2000 kg Dimensions: 3110 x 1250 x 2280 mm Standard Bucket Capacity: 0.040 cbm Engine: Laidong 385 / Kubota D722 Power Output: 25 hp / 18 kW or 16.4 hp / 12.2 kW Issue Rating: EURO V Displacement: 1.617 / 0.719 L Cooling Method: Water-cooled Max. Digging Depth: 2050 mm Bucket Digging Force: From 10 kN Hydraulics: Permco TJ Gradeability: 35°
The MB 35 takes operator efficiency and machine durability to the next level. With a robust chassis, high torque capacity, and superior arm force, it's tailored for demanding commercial work. From site prep to demolition, this machine handles heavier tasks with ease—offering a professional-grade experience packed into a versatile compact frame. Weight: 3500 kg Dimensions: 4180 x 1500 x 2300 mm Standard Bucket Capacity: 0.100 cbm Engine: Xinchai 490 / Kubota V1505 Power Output: 27.4 hp / 36.8 kW or 33 hp / 26.5 kW Issue Rating: EURO V Displacement: 2.67 / 1.498 L Cooling Method: Water-cooled Max. Digging Depth: 2500 mm Bucket Digging Force: 22 kN Hydraulics: Permco TJ Gradeability: 35°
The flagship of the lineup, the MB 40 delivers top-tier performance for high-demand job sites. Built for heavy-duty excavation, this model features exceptional digging force, unmatched gradeability, and premium operator comfort. It's ideal for contractors who need the strength of a full-sized excavator in a more compact, easily transportable unit. Weight: 4000 kg Dimensions: 4400 x 1600 x 2300 mm Standard Bucket Capacity: 0.700 cbm Engine: Xinchai 490 / Kubota V1505 Power Output: 27.4 hp / 36.8 kW or 33 hp / 26.5 kW Issue Rating: EURO V Displacement: 2.67 / 1.498 L Cooling Method: Water-cooled Max. Digging Depth: 2650 mm Bucket Digging Force: 55 kN Hydraulics: Permco TJ Gradeability: 35°
Machine type MIG/MAG welding system Make MERKLE Type RedMIG 2800 K Connection voltage 3 x 400 volts Adjustment range 25 - 280 amperes Switch-on time 30% ED at 280 amperes 60% ED at 210 amperes Current setting 14 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 4-wheel drive DV 26 Fuse 16 Ampere Dimensions L x W x H 800 x 460 x 655 mm Weight 80 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch 3 mtr. Long 1 piece ground cable 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece of protective glass 10 DIN 1 piece of white glass 1 piece spare part box, kpl ...
Machine type MIG/MAG welding system Make Merkle Type RedMIG 1600 K Connection voltage 1 x 230 volts Adjustment range 25 - 160 amperes Switch-on time 30% ED at 160 amperes 60% ED at 130 amperes Current setting 7 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 2-roll drive Fuse 16 Ampere Dimensions L x W x H 800 x 460 x 620 mm Weight 65 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 157 G, 3 mtr. Long 1 piece ground cable 4 mtr long, 25 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 roll of welding wire, D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece of lens 90 x 110 mm white 1 piece of protecti ...
Machine type MIG/MAG welding system Make MERKLE Type RedMIG 2000 K Connection voltage 3 x 400 volts Adjustment range 25 - 200 amperes Switch-on time 30% ED at 200 amperes 60% ED at 140 amperes Current setting 7 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 2-roll drive Fuse 16 Ampere Dimensions L x W x H 800 x 460 x 655 mm Weight 70 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch, 3 mtr. Long 1 piece ground cable 4 mtr. Long 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield 1 piece of protective glass 10 DIN 1 piece of white glass 1 piece spare part box ...
CNC Engraving Machine MÜLLER LCF - 2 Travel: X 375 mm Y 570 mm Z 90 mm Technical0.321020121002 Data: Table size 700 mm x 480 mm Weight: 50 kg Exterior dimensions: Length: 700 mm Width: 500 mm Height: 350 mm Accessories: Computer Screen Keyboard Mouse Software Control Kress cutter Vacuum pump Valve Spray Mist With this, versch. Collet and cutter - NEW
Machine type MIG/MAG inverter welding system without BiPower Make Merkle Type MobiMIG 280 K Plant No. 123.035 Connection voltage 3 x 400 volts Adjustment range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 4-wheel transmission DV 26 Fuse 16 Ampere Dimensions L x W x H 470 x 255 x 545 mm Special accessories ColdMIG welding process, e-welding MIG soldering, filler wire welding Weight 27 kg Age 2 years Condition workshop-tested, very good, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer Argon w ...
New: MB 12 - SH | 1.2 Ton Mini Excavator | with Warranty Location: Poland | Availability: Pre-order Product Overview: We offer the MB 12 - S|H, a 1.2-ton mini excavator with a 1,000 operating hour warranty. Ideal for landscaping. Key Features: Operating weight: 1,200 kg Emission standard: EU Stage V Digging force: Arm: 3 kN / Bucket: 7 kN Dimensions: 2870 x 940 x 2280 mm Operator cabin: open Technical Specifications Engine: Co-op D192F Power: 7.6 kW / 10.3 HP at 3,000 rpm Torque: 25.5 Nm at 2,880 rpm Fuel consumption: 275–280 g/kWh Cooling: Air-cooled Fuel type: Diesel Number of cylinders: 1 Hydraulic System: Pump: Gear pump Flow rate: 18 L/min Valves: Permco Tianjin multi-way hydraulic valve Swing motor: LKC Travel motor: LKC Hydraulic hoses: Continental Hydraulic oil capacity: 13 L Max. working pressure: 160 ...
NOW IN STOCK: New MB 12 - SH | 1.2 Ton Mini Excavator | With Warranty Location: Poland | Availability: In stock Product Overview: We offer the MB 12 - SH, a 1.2-ton mini excavator with a 1,000 operating hour warranty. Ideal for landscaping and light construction work. Key Features: Operating weight: 1,200 kg Emission standard: EU Stage V Digging force: Arm: 3 kN / Bucket: 7 kN Dimensions: 2870 x 940 x 2280 mm Operator cabin: open Technical Specifications Engine: Co-op D192F Power: 13.4 kW / 18 HP at 3600 rpm Torque: 43 Nm at 2600–2800 rpm Cooling: Water-cooled Fuel type: Diesel Number of cylinders: 3 Hydraulic System: Pump: Gear pump Flow rate: 18 L/min Valves: Permco Tianjin multi-way hydraulic valve Swing motor: LKC Travel motor: LKC Hydraulic hoses: Continental Hydraulic oil capacity: 13 L Max. working pre ...
New MB 12 - SH | 1.2 Ton Mini Excavator | With Warranty Location: Poland | Availability: Production machine Product Overview: We offer the MB 12 - KSH, a 1.2-ton mini excavator with a 1,000 operating hour warranty. Ideal for landscaping and light construction work. Key Features: Operating weight: 1,200 kg Emission standard: EU Stage V Digging force: Arm: 3 kN / Bucket: 7 kN Dimensions: 2870 x 940 x 2280 mm Operator cabin: Closed Cabin Technical Specifications Engine: Co-op D192F Power: 13.4 kW / 18 HP at 3600 rpm Torque: 43 Nm at 2600–2800 rpm Cooling: Water-cooled Fuel type: Diesel Number of cylinders: 3 Hydraulic System: Pump: Gear pump Flow rate: 18 L/min Valves: Permco Tianjin multi-way hydraulic valve Swing motor: LKC Travel motor: LKC Hydraulic hoses: Continental Hydraulic oil capacity: 13 L Max. working ...
Machine type MIG/MAG inverter welding system without BiPower Make Merkle Type MobiMIG 280 K Connection voltage 3 x 400 volts Adjustment range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 4-wheel transmission DV 26 Fuse 16 Ampere Dimensions L x W x H 470 x 255 x 545 mm Special accessories ColdMIG welding process, e-welding MIG soldering, filler wire welding Weight 27 kg Age 12 months Condition workshop-tested, very good, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer Argon with 2 pressure gau ...
Machine type MIG/MAG inverter welding system Make Merkle Type MobiMIG 180 K Connection voltage 1 x 230 volts Adjustment range 25 - 180 amperes Switch-on time 20% ED at 180 amperes 60% ED at 110 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 2-wheel transmission Fuse 16 Ampere Dimensions L x W x H 450 x 210 x 480 mm Special accessories ColdMIG welding process E-welding, MIG soldering Filling wire welding Weight 17 kg Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SBT 157 G, 3 mtr. Long 1 piece ground cable 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-200 coil, 5 kg 1 can ...
Machine type MIG/MAG inverter welding system with bi-power setup Make Merkle Type MobiMIG 280 K - BiPower Connection voltage 230/400 volts Adjustment range 25 - 280 amperes Switch-on time 35% ED at 280 amperes 60% ED at 240 amperes Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Wire feed gearbox 4-wheel transmission DV 26 Fuse 16 Ampere Dimensions L x W x H 470 x 255 x 545 mm Special accessories ColdMIG welding process, e-welding MIG soldering, filler wire welding Bi-Power Setup Weight 27 kg Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories 1 piece welding torch SBT 307 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reduc ...
Machine type MIG/MAG welding system Make CEBORA Type MIG STAR 550 S Plant No. 991502 Connection voltage 3 x 400 volts Setting range 40 - 500 amperes Switch-on time 60% ED at 500 amperes 100% ED at 390 amperes Current setting 32 switching stages Cooling transformer due to built-in fan Cooling burner water-cooled Execution of mobile industrial plant with separate DV-case Wire feed gearbox 4-wheel drive Fuse 32 Ampere Dimensions L x W x H 1,000 x 500 x 1,250 mm Weight 190 kg Age approx. 25 years Condition workshop-tested, good, incl. UVV test protocol Special accessories 3 x throttle pick-ups Scope of delivery Welding system with the following accessories: 1 piece welding torch 3 mtr. Long 1 piece ground cable 1 piece pressure reducer Argon with 2 pressure gauges 1 piece spare part box kpl. Equipped 1 piece user manual Warr ...
Machine type MIG/MAG welding system Make Merkle Type CompactMIG 220 K Connection voltage 3 x 400 volts Setting range 25 - 220 amperes Switch-on time 40% ED at 220 amperes 60% ED at 170 amperes Current setting 7 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed 4-wheel gearbox DV 26 Fuse 16 Ampere Dimensions L x W x H 870 x 480 x 740 mm Weight 90 kg Special Accessories Display Automatic wire Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 157 G, 3 mtr. Long 1 piece ground cable 4 mtr. long, 35 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non-stick spray 1 piece hand shield ...
Machine type MIG/MAG welding system Make MERKLE Type CompactMIG 400 DW Connection voltage 3 x 400 volts Adjustment range 25 - 400 amperes Switch-on time 35% ED at 400 amperes 60% ED at 310 amperes 100% ED at 230 amperes Current setting 14 switching stages Cooling transformer due to built-in fan Cooling burner water-cooled Execution of mobile industrial plant with separate DV-case Wire feed 4-wheel gearbox DV 26 Fuse 16 Ampere Dimensions L x W x H 940 x 445 x 1,040 mm Weight 170 kg Special accessories display, automatic wire, VB cable 1.6 mtr. Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 504 W, 3 mtr. long 1 piece ground cable 4 mtr. long, 70 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 ...
Machine type MIG/MAG welding system Make MERKLE Type CompactMIG 400 K Connection voltage 3 x 400 volts Adjustment range 25 - 400 amperes Switch-on time 35% ED at 400 amperes 60% ED at 310 amperes 100% ED at 230 amperes Current setting 14 switching stages Cooling transformer due to built-in fan Cooling burner gas-cooled Execution of mobile industrial plant Wire feed 4-wheel gearbox DV 26 Fuse 16 Ampere Dimensions L x W x H 940 x 480 x 760 mm Weight 140 kg Special accessories display, automatic wire Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 307 G, 3 mtr. long 1 piece ground cable 4 mtr. long, 70 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 roll welding wire D-300 coil, 5 kg 1 can of non ...
Machine type Electrode inverter welding rectiveror Make Merkle Type LiteARC 180 Connection voltage 1 x 230 volts Adjustment range 20 - 170 amperes Switch-on time 25% ED at 170 amperes 60% ED at 130 amperes 100% ED at 115 amperes Current adjustment infinitely variable max. weldable material thickness 4 mm Cooling inverter by built-in fan Version of portable assembly line Fuse 16 Ampere Dimensions L x W x H 360 x 140 x 230 mm Weight 5 kg Age 12 months Condition workshop-tested, very good, as new incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece ground cable 1 piece electrode cable 1 piece hand shield 1 piece of lens 90 x 110 mm, white 1 piece protective glass 90 x 110 mm, 10 DIN 1 piece slag hammer, heavy version 1 piece steel wire brush, 2-row 1 piece mains plug 230 V, ful ...
Machine type Electrode inverter welding rectiveror Make Merkle Type LiteARC 160 Connection voltage 1 x 230 volts Adjustment range 15 - 160 amperes Switch-on time 25% ED at 150 amperes 60% ED at 90 amperes 100% ED at 80 amperes Current adjustment infinitely variable max. weldable material thickness 4 mm Cooling inverter by built-in fan Version of portable assembly line Fuse 16 Ampere Dimensions L x W x H 360 x 150 x 240 mm Weight 6 kg Age 12 months Special accessories Carrying strap Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece ground cable 1 piece electrode cable 1 piece hand shield 1 piece of lens 90 x 110 mm, white 1 piece protective glass 90 x 110 mm, 10 DIN 1 piece slag hammer, heavy version 1 piece steel wire brush, 2-row 1 ...
Machine type MIG/MAG welding system Make MERKLE Type OptiMIG 351 DW Connection voltage 3 x 400 volts Setting range 25 - 350 amperes Switch-on time 60% ED at 350 amperes 100% ED at 300 amperes Current setting 28 switching stages Cooling transformer due to built-in fan Cooling burner water-cooled Execution of mobile industrial plant with separate DV-case Wire feed gearbox 4-wheel transmission DV 26 Fuse 32 Ampere Dimensions L x W x H 990 x 510 x 1.135 mm Weight 210 kg Special accessories Volt and Ampere digital display Automatic wire Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch 3 mtr. long 1 piece ground cable 4 mtr. long, 70 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 piece spare part box k ...
Machine type MIG/MAG welding system Make MERKLE Type OptiMIG 351 KW Connection voltage 3 x 400 volts Setting range 25 - 350 amperes Switch-on time 60% ED at 350 amperes 100% ED at 300 amperes Current setting 28 switching stages Cooling transformer due to built-in fan Cooling burner water-cooled Execution of mobile industrial plant Wire feed gearbox 4-wheel transmission DV 26 Fuse 32 Ampere Dimensions L x W x H 990 x 510 x 845 mm Weight 190 kg Special accessories Volt and Ampere digital display Automatic wire Age 12 months Condition workshop-tested, as new, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch SB 504 W, 3 mtr. long 1 piece ground cable 4 mtr. long, 70 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 piece spare part box kpl. Equipped 1 piece use ...
Machine type MIG/MAG welding system Make MERKLE Type OptiMIG 451 KW Connection voltage 3 x 400 volts Adjustment range 25 - 450 amperes Switch-on time 40% ED at 450 amperes 60% ED at 420 amperes 100% ED at 340 amperes Current setting 42 switching stages Cooling transformer due to built-in fan Cooling burner water-cooled Execution of mobile industrial plant Wire feed gearbox 4-wheel transmission DV 26 Fuse 32 Ampere Dimensions L x W x H 990 x 510 x 845 mm Weight 200 kg Special accessories Volt and Ampere digital display Automatic wire Age 12 months Condition workshop-tested, as new, incl. UVV workshop test protocol Scope of delivery Welding system with the following accessories: 1 piece welding torch 3 mtr. long 1 piece ground cable 4 mtr. long, 70 sqmm 1 piece pressure reducer Argon with 2 pressure gauges 1 piece spare part box ...
Mesutronic MN 5.1 PW50 metal check for bulk materials, etc. without integrated reject/ejection mechanism, reject/ejection time adjustable from 0.1 s to 10 s, inlet height (middle of the tube) approx. 755 mm, outlet height (middle oft he tube) approx. 450 mm, tube outer diameter approx. 32 mm, tube inner diameter approx. 28 mm, electrics 100-240V/50/60Hz, machine dimensions approx. 350 x 350 x 770 mm (LxWxH), machine net weight approx. 35 kg
CNC controller: Siemens 840D sl with CELOS ERGOline Capacity X-axis travel mm: 480 (–10) Y-axis travel mm: ±100 Z-axis travel mm: 845 B-axis travel mm: ±110° (0,001º) C-axis: 360º (0,001º) Turning length mm: 800 Max. turning diameter mm: ø: 500 Distance between spindle centers mm: 1.020 Turn-mill spindle Speed spindle rpm: 12.000 Drive power kW: 22 / 19 Tool magazine Magazine places: 24 Tool holder: HSK-A63 Tool length max. mm: 300 Tool diameter max. mm: 125 Tool weight max kg: 7 Main spindle Speed spindle rpm: 5.000 Drive power spindle kW: 25 / 34 (100 / 40%) Spindle bore mm: 67 Maximun torque Nm: 380 / 280 Counter spindle Speed spindle rpm: 6.000 Drive power spindle kW: 20 / 27 (100 % / 40%) Spindle bore mm: 52 Maximun torque Nm: 170 Counter spindle travel mm: 800 Coolant system Tank capacity liter: 600 L High-pre ...
Used from plant disassembly. Siemens Simodrive Posmo-SI with Alpha gearbox Engine: 6SN2500-2BF00-0GG0 Transmission: TP 050-MF1-5 -071-000 Dimensions L x W): approx. 65 x 25 cm The machine is electrically tested before sale and receives a DIN VDE 0113 test report.
Hanselifter E-MES150-15-05 Electric Box Lifter Minilift 150kg 0.15 kW 2x12V Excellent maneuverability for tight spaces Electronic height change of the platform Operating terminal for easy handling when lifting and lowering Increased safety thanks to approx. one and a half metre supply cable and an integrated charger with overload protection Charging possible at any standard socket With parking brakes on both swivel castors Dimensions L x W x H: 870 x 600 x 1790 mm Drive type: semi-electric Overall height: 1790 mm Tyres: polyurethane Ground clearance: 70 mm Net weight: 66 kg Fork length: 475 mm Lifting speed: 50 mm/s Lifting height: 1500 mm Load center of gravity: 230 mm Platform height max.: 1500 mm Platform dimensions L x W mm: 475 x 600 mm Wheelbase: 680 mm Load capacity: 150 kg Turning radius: 850 mm You can find more box jacks - new and used - in our shop! ...
optical angel measuring unit. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
With matching spacer rings according to photos. Scope of delivery according to photo 1.
Electric motor ALMO MTA 132 SX2 recon Ball bearings renewed from the rotor. Seals renewed. The engine has slight traces of smoke but is in an overhauled and installable condition. Data from the engine see pictures.
grinding diameter: 5 - 255 mm grinding length: 300 mm centre height: 130 mm grinding length at plunge grinding: 50 mm control: SINUMERIK 805 grinding spindle speed: 25 - 1400 U/min work piece spindle speed: 0 - 500 U/min feed of grinding spindle slide cross: 0 - 5000 mm/min table speeds: 0 - 5 m/min grinding wheel diameter: 450 mm total power requirement: 10 kW weight of the machine ca.: 2,3 t dimensions of the machine ca.: 2,65 x 2,2 x 2,35 m Accessories: grinding wheel with flange, 3-jaw chuck, electron. hand wheel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Bickel MPA 65 Electronically controlled Stamp Perforating machinePerforation of postal stamps, tokens, calendars. Size 900 x 650 mm with lot of tools.SCC control and positioning over monitor. Automatic central greasing. List of tools: base tools - 35,5 mm 48,28 mm 24,14 mm Perforation only with line: 48,28 mm round (big)- Ø35,5 mm 35,5 mm round (small) – Ø24,14 mm 48,28 x 40,53 mm shape of hart 48,28 mm with protection of romb 35,5 mm with protection romb Closed sizes: 48,28 x 24,14 mm 35,50 x 25,56 mm 35,50 x 29,82 mm Age: 1992 Machine tehnicaly controled/ checqued. Cleaned. With machine there is automatic delivery and jogger.
Takeuchi TB 230 Year of construction 2017 Operating hours 980 Powertilt with load hook and hydraulic Lehnhoff HS03 quick coupler 1 digging bucket 300 mm
Machine type MIG/MAG welding system MerkLE brand Type M 254 K Connection voltage 3 x 400 Volt Setting range 25 – 250 amps Duty cycle 60 % ED at 250 Ampere 100% ED at 200 amps Current adjustment infinitely variable Cooling transformer by built-in fan Cooling burner gas-cooled Version of mobile compact system Wire feed gearbox 4-roller drive DV 25 Fuse 16 amps Dimensions L x W x H 955 x 460 x 780 mm Weight 110 kg Age approx. 25 years Condition workshop tested, good incl. UVV test report Scope of delivery welding system with the following accessories: 1 piece welding torch SBT 307 G, 3 mtr. long 1 piece ground cable 1 piece pressure reducer with 2 pressure gauges 1 roll welding wire D 300, 5 kg 1 pair of welder gloves with cuff 1 piece spare parts box kpl. Equipped 1 can of non-stick spray ME 4000 6 months warranty! 1 piec ...
Machine Type Electrode Inverter Welding Rectifier with bi-power setup Merkle brand Type MobiARC 284 cel Plant No. 106.539 Connection voltage 230/400 volts Setting range 20 – 280 amps Duty cycle 35 % ED at 280 Ampere 60% ED at 240 amps 100% ED at 210 amps Current adjustment infinitely variable weldable material thickness 7 mm Cooling inverter by built-in fan Special accessories Bi-Power setup Version portable mounting system Fuse 16 amps Dimensions L x W x H 485 x 200 x 435 mm Weight 17 kg Age 6 years Condition workshop tested, good, incl. UVV test report Scope of delivery welding system with the following accessories: 1 piece electrode cable 1 piece ground cable 1 piece hand shield 1 piece attachment glass 90 x 110 mm white 1 piece of protective glass 90 x 110 mm 10 DIN 1 pair of welder gloves with cuff 1 piece of ...
maximum number of results exceeded
please refine your search
