m 520 used for sale

GeneralVertical Machining Center; Control: Control SIEMENS 828D CharacteristicsTable surface850 x 650 mmDimensions (L x W x H)3,07 x 2,67 x 2,84 mRapid feed X / Y / Z24/24/24 m/minMovement X / Y / Z550/550/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with24 PositionsMax. torque64 NmTorque (100% DC)43 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWSpeed max.10000 rpmWeight approx.5600 KgSK40 interfaceTool clamping SK 40 for pull-studs DIN 69872

GeneralVertical-Machining centre Stealth Design; Control: CELOS with Heidenhain TNC 640 Technical DataRapid traverse longitudinal/transverse/vertical42/42/42 m/minFeed rate longitudinal/transverse/vertical1-42000/1-42000/1-42000 mm/minWorking area 1Cross700 mmLongitudinal1450 mmVertical550 mmIntegrated motor spindle speedMASTER®Integrated motor spindle speedMASTER® At speeds > 18.000 min-1, the use of tools with dual contact system (BIG-PLUS®) is stipulated.Drive power (100% DC) 25 kWDrive power (40% DC) 35 kWTorque (100% DC) 86 NmTableTable surface 1760 x 750 mmClamping System DIN ISO 7388-3-ADSpindle taper SK40 Tool holder DIN ISO 7388-1-ASpeed range - 20000 rpmTorque (40% DC) 130 NmSlot width 14 mmMaximum load (table centre) 1500 KgNumber of Slots 7Distance between T-Slots 100 mmCabin roofCabin roof In sheet steel design Open and close via front doorSpecial equipmentClamping pneuma ...

GeneralVertical Machining Center; Control: Control SINUMMERIK ONE CharacteristicsTable surface850 x 650 mmDimensions (L x W x H)3,07 x 2,67 x 2,84 mRapid feed X / Y / Z24/24/24 m/minMovement X / Y / Z550/550/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with24 PositionsMax. torque64 NmTorque (100% DC)43 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWSpeed max.10000 rpmWeight approx.5600 KgSK40 interfaceTool clamping SK 40 for pull-studs DIN 69872Electronic HandwheelExternal electronic HandwheelSpecial equipment4th. axis Lehmann

x-travel: 1250 mm y-travel: 650 mm z-travel: 600 mm total power requirement: kW weight of the machine ca.: t required space: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

GeneralVertical-Machining centre Stealth Design; Control: CELOS X with Siemens 840D SL Operate CharacteristicsTable surface1460 x 750 mmMaximum load (table centre)1500 KgTool Magazine with40 PositionsMovement X / Y / Z1150/700/550 mmRapid feed X / Y / Z42/42/42 m/minWeight approx.12900 KgSpindle speed 20 - 12,000 rpm SK50, 288NmSpindle speed 20 - 12.000 rpm SK50 for tool taper according to DIN ISO 7388-1-A50 with power 44/32 kW // 59.0/42.9 hp with torque 288/187 Nm (40/100% DC) (differently from standard)Tool magazine 40 pocketsTool magazine 40 pockets SK50 chain magazine with pockets and double gripper, incl. manually direct loading into the tool magazineCoolant-air blast change-overCoolant - Air-blast changeover external switchable via M-FunctionAir blast through spindle centreAir blast through spindle centre activated by M function, maintained air with low oil rateInternal coolant su ...

GeneralVertical machining center in C-frame-design New DMG MORI Design Direct Measuring system X,Y,Z; Control: CELOS with Heidenhain TNC 640 Technical DataFeed rate longitudinal/transverse/vertical1-42000/1-42000/1-42000 mm/minRapid traverse longitudinal/transverse/vertical42/42/42 m/minWorking area 1Longitudinal650 mmCross520 mmVertical475 mmTool changerType of magazineChain Type of gripperDouble gripper Number of tools30 TableTable surface 960 x 570 mmMaximum load (table centre) 800 KgSlot width 14 mmNumber of Slots 5Distance between T-Slots 100 mmSpindle speed 15,000 rpm, 200 NmMotor spindle speedMASTER® SK 40 Spindle speed 20 - 15,000 min-1 Output 46 kW / 30 kW (62 hp / 40 hp) Torque 200 Nm / 130 Nm (148 ft lbs / 96 ft lbs) (40 / 100 % duty cycle) BIG-PLUS® tools possibleTool magazine 30 pockets SK40Tool magazine 30 pockets SK40 Chain magazine with pockets and with double gripper,  ...

GeneralVertical machining center in C-frame-design New DMG MORI Design Direct Measuring system X,Y,Z; Control: CELOS with Siemens 840D sl Operate Technical DataFeed rate longitudinal/transverse/vertical1-42000/1-42000/1-42000 mm/minRapid traverse longitudinal/transverse/vertical42/42/42 m/minWorking area 1Cross520 mmLongitudinal650 mmVertical475 mmTool changerType of magazineChain Type of gripperDouble gripper Number of tools60 TableTable surface 960 x 570 mmMaximum load (table centre) 800 KgSlot width 14 mmNumber of Slots 5Distance between T-Slots 100 mmSpindle speed 20.000 rpmMotor spindle speedMASTER® HSK-A63 Spindle speed 20 - 20,000 min-1 Output 35 kW / 25 kW (47 hp / 33 hp) Torque 130 Nm / 86 Nm (96 ft lbs / 63 ft lbs) (40 / 100 % duty cycle)Tool magazine 60 pockets HSK-A63Tool magazine 60 pockets HSK-A63 Chain magazine with pockets and with double gripper, incl. manually direct t ...

CharacteristicsTable surface1460 x 750 mmMaximum load (table centre)1500 KgTool Magazine with30 PositionsMovement X / Y / Z1150/700/550 mmRapid feed X / Y / Z42/42/42 m/minWeight approx.12900 KgGeneralVertical-Machining centre Stealth Design; Control: CELOS X with Siemens 840D SL Operate Spindle speed 15,000 rpm, 200 NmMotor spindle speedMASTER® SK 40 Spindle speed 20 - 15,000 min-1 Output 46 kW / 30 kW (62 hp / 40 hp) Torque 200 Nm / 130 Nm (148 ft lbs / 96 ft lbs) (40 / 100 % duty cycle) BIG-PLUS® tools possibleTool magazine 30 pockets SK40Tool magazine 30 pockets SK40 Chain magazine with pockets and with double gripper, incl. manually direct loading into the tool magazineCoolant-air blast change-overCoolant - Air-blast changeover external switchable via M-FunctionAir blast through spindle centreAir blast through spindle centre activated by M function, maintained air with low oil rat ...

GeneralVertical Machining Centres; Control: DMG MORI SLIMline® Multi-Touch control CharacteristicsMaximum load (table centre)800 KgDimensions (L x W x H)3,3 x 2,7 x 2,94 mRapid feed X / Y / Z30/30/30 m/minMovement X / Y / Z800/560/510 mmSpindle taperSK 40 DIN 69871 Tool Magazine with30 PositionsMax. torque83 NmTorque (100% DC)57 NmDrive power (40% DC)13 kWDrive power (100% DC)9 kWSpeed max.12000 rpmTable surface1100 x 560 mmWeight approx.5550 KgDirect measuring system X,Y,ZDirect Measuring System X, Y, Z inclusive Air Purge for Measuring SysteminlineMASTER® spindle 12.000 rpminlineMASTER® spindle 12.000 rpm Spindle speed range 20 to 12.000 rpm Tool Taper SK40 DIN69871 with BIG PLUS inteface Tool clamping according to DIN69872 Power: 13kW (40% DC) / 9kW (100% DC) Torque: 83 Nm (40% DC) / 57 Nm (100% DC) bearings oil-air lubrSK40 interfaceTool clamping SK 40 for pull-studs DIN 69872NC-D ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmMain drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmC-Axis Speed100 rpmMax. torque (40% DC)192 NmTorque of C-Axis (holding torque)168 NmWork spindleSpindle diametre on front bearing120 mmSpindle noseA2-6 Spindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axis universal turning machine with - partiall hollow clamping device (hydr.) inner draw tube Ø 52 mm - C-axis and spindle brake (hydr.) - 12 stations circle revolver Sauter reception acc. VDI 30, DIN 69880-30 with tool drive Connection/drive acc. DIN 5480 Direct measuring system, glas scale in X-axis - tailstock; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways500 mmTransverse stroke190 mmLongitudinal stroke525 mmClamping chuck diameter max.210 mmWork spindle (left)Spindle noseFlat flange Spindle bore73 mmDiametre of spindle nose140h5 mmSpindle diametre on front bearing100 mmMain drive 1Drive power (100% DC)13 kWSpeed range20 - 6000 rpmTorque (100% DC)171 NmC-Axis Speed-300 rpmTorque of C-Axis (holding torque)192 NmTool holder 1Number of tool stations12 Shank diametre according to DIN 6988030 mmNumber of driven tools12 Speed max.-500 ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmMain drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 NmC-Axis Speed100 rpmTorque of C-Axis (holding torque)168 NmWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Speed max.6000 rpmNumber of driven tools12 Power max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmMain drive 1Type of main driveAC Drive power (40% DC)14 kWDrive power (100% DC)12,6 kWSpeed range-5500 rpmTorque (100% DC)171 NmC-Axis Speed100 rpmMax. torque (40% DC)192 NmTorque of C-Axis (holding torque)168 NmWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmMain drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 NmC-Axis Speed100 rpmTorque of C-Axis (holding torque)168 NmWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmGeneral2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Main drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 NmC-Axis Speed100 rpmTorque of C-Axis (holding torque)168 NmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmMain drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 NmC-Axis Speed100 rpmTorque of C-Axis (holding torque)168 NmWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axes universal turning center with driven tools, C-axis and Y-axis; Control: CELOS with Siemens 840D sl Operate Main drive 1Type of main driveAC Drive power (100% DC)12,6 kWDrive power (40% DC)14 kWSpeed range-5500 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 NmC-Axis Speed100 rpmTorque of C-Axis (holding torque)168 NmWorking areaSwing diameter over bed650 mmSwing diameter over X linear guideways370 mmMax machining diameter320 mmClamping chuck Ø250 mmX travel250 mmY travel+/-50 mmZ travel550 mmDistance between spindle noses800 mmWork spindleSpindle noseA2-6 Spindle diametre on front bearing120 mmSpindle bore73 mmBar diameter max.65 mmTool holder 1Number of tool stations12 Number of driven tools12 Speed max.6000 rpmPower max. (40% DC)4,6 kWDMG MORI IoTconnectorIoTconnector connects DMG MORI machines as well as third-party machines with CELOS. Standardized interfaces enable d ...

General2-axis universal turning machine with - partiall hollow clamping device (hydr.) inner draw tube Ø 52 mm - C-axis and spindle brake (hydr.) - 12 stations circle revolver Sauter reception acc. VDI 30, DIN 69880-30 with tool drive Connection/drive acc. DIN 5480 Direct measuring system, glas scale in X-axis - tailstock; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways500 mmTransverse stroke210 mmLongitudinal stroke525 mmClamping chuck diameter max.210 mmMain drive 1Drive power (100% DC)13 kWSpeed range20 - 6000 rpmTorque (100% DC)171 NmC-Axis Speed-300 rpmTorque of C-Axis (holding torque)192 NmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose140h5 mmSpindle bore73 mmSpindle diametre on front bearing100 mmTool holder 1Number of tool stations12 Shank diametre according to DIN 6988030 mmNumber of driven tools12 Speed max.-500 ...

General2 spindles automatic lathe - 2 cross slides - Main and counter spindle - Y axis on slide 1 - Y axis on slide 2 - C axis on main spindle - C axis on counter spindle - Chip tank with coolant system and coolant pump - Part unloading chute; Control: Numeric control Fanuc 32i Working areaBar diameter max.20 mmCounter spindle collet cleaningCounter spindle collet cleaning with coolantChanging kit from steady to sliding headstockChanging kit from steady to sliding headstock including application bush type Dunner B260 and bush-spindle syncronismAdditional charge for belt type chip conveyorAdditional charge for belt type chip conveyor, compatible with shaft-unloading-device Specific chip removol systems (for example: scraping blades chip conveyors, with additional filtering systems) are recommended in case of short chip material machininOil mist filter for emulsion or oilOil mist filter fo ...

Key data: 3020 mm, 2 mm

with motor backgauge, numerical NC control, manual bending beam lowering, foot switch Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Sheet width: 3020 mm Sheet thickness steel: 2.0 mm Sheet thickness aluminium: 3.0 mm Sheet thickness front: 1.5 mm Back gauge: 1000 mm Colour: green Total power requirement: 400 V Dimensions: 3800 x 1000 mm Machine weight: 4500 kg Upper beam stroke: 200 mm without roller scissors/ Opening width: 200 mm

Zucchelli Forni Modular 2C2T Modular oven Serial: 2020E0860 2020, Stainless, two deck modular oven, chamber size 800mm x 600mm x 160mm, with adjustable temp and time controls, stone based, electric, 11.3Kw, mounted on mobile rack storage, 3Ph

max. format 78 x 115 cm Year of construction 2002 MC Control Counting device MCC 3 Round stack feeder Dual feed 6 fold pockets in the parallel fold section Downstream knife shaft Window rebate bag Vertical stack delivery Delivery date: immediately Price on request. We supply and install worldwide.

5-axis machining center Mori Seiki NHX 5000 Year of construction 2011 (bought new in 2013) Hours10768 Processing time 7172 hours Electricity one hour 29288 With few operating hours, used only for single part to small series production, mainly for special mechanical engineering The specifications are as follows: Travels: Cylinder Ø 500 x 700 Control M730BM (Mapps2) Speed 10,0000 rpm. Tool holder SK40 DIN 69871 Tool changer 60-fold Pallet changer 2-fold Accessories: Documentation Internal cooling Knoll 50 bar Conveyor Activation to 400 tool positions Pine pallet with long zero point clamping system Lang tensioning tower approx. 100 pieces of tool holders SK40 An on-site inspection is possible at any time by appointment.

Manufacturer: MINIPAN Model: CMBY 0400X000.06 GIROPN Year of Manufacture: 2011 Type of Machine: Soft dough biscuit forming machine • Power supply: 400V • Power consumption: 3.2 kW • Backlit LCD display with touchscreen • Rollers for soft dough • Fixed molds with wire cutter • Rotating molds: "guillotine" that opens when the dough is placed and then closes for precise dosing without dripping • Sheet size: width 400 mm, Length: min. 600 mm, max. 800 mm • Sheet types: 2 internally inclined edges, magazine for up to 20 sheets • Dimensions: Length = 2600 mm Width = 990 mm Height = 1400 mm Weight = 530 kg • Sugar dispenser at the machine outlet • DÜBOR TSA 800/10 plate lubricator (, 2012) with 5 spray nozzles Find more here - / Contact us at -

DMG DMC70H year 2007 Hours in picture he 2007 Deckel Maho DMC 70 H is a horizontal machining center produced by DMG (Deckel Maho Gildemeister), a renowned German manufacturer known for high-quality CNC machining centers. Here are the key details about this model: Key Specifications: - Type: Horizontal Machining Center - Year: 2007 - Table Size: Usually features a pallet size of 630mm x 630mm, though this can vary based on the setup. - X-Axis Travel: Around 700 mm. - Y-Axis Travel: Around 800 mm. - Z-Axis Travel: Around 800 mm. - Spindle Speed: Can reach up to 18,000 rpm, depending on the specific configuration. - Spindle Motor: Offers robust power, typically around 35 kW (may vary based on options). - Automatic Pallet Changer: Often comes with an automatic pallet changer, improving productivity by minimizing downtime during setup. - High-Rigidity Design: Known for its rigid construct ...

GeneralVertical Machining centre; Control: DMG MORI ERGOline IV HEIDENHAIN TNC 7 CharacteristicsTable surface900 x 600 mmTool Magazine with60 PositionsMovement X / Y / Z600/600/510 mmRapid feed X / Y / Z30/30/30 m/minAC main driveSpindle speed range 20 to 15.000 rpm AC main drive:20/14,5 kW (40/100% DC) Tool taper SK40 DIN 69871 Tool clamping according to DIN69872Direct measuring system X,Y,ZDirect Measuring System X, Y, Z inclusive Air Purge for Measuring SystemProduction Package 20 bar with chip conveyorProduction Package 20 bar with chip conveyor Option includes: - Internal coolant supply 20 bar - Chip conveyor (scraper type) with tank capacity: 200 l(left) - Bed flushing via M-Function - Coolant spray gun for swarf removal - External electronic handwheAir coolant internal (through spindle centre)Air Coolant Internal (through spindle centre) switchable via M-Function maintained air wi ...

DMG DMC 70 H year 2007 The 2009 Deckel Maho DMC 70 H is a horizontal machining center manufactured by DMG (Deckel Maho Gildemeister), which is a well-known German company that produces high-precision CNC (computer numerical control) machine tools. Hours in picture Find more here - / Contact us at -

Key data: 5000 kN, 80 mm

KM 500/2700C2 Specifications Closing page: Clamping force: 5000 kN Wooden dimension h x v: 900 x 800 mm Min. installation height: 480 mm Plate spacing max.: 1650 mm Centering: 200 mm Tool weight: 7900 kg Splash Side: Screw diameter: 80 mm Capacity: 1433 cc Spray pressure: 1829 bar Equipment: MC 4 Control Core moves: 2+2

max rod Ø: 20 mm Turning length: 350 mm Turning diameter over bed: 240 mm Speed: 23-4400 1/min 6-station turret 2 longitudinal slides 2 cross slides IEMCA Bar Feeder BOSS 432/32 max. bar length 3,200 mm

Key data: 700 mm, 450 mm, 450 mm

Universal Milling Machine MAHO MH 800 Travel X: 700 mm Travel Y: 450 mm Travel Z: 450 mm Spindle SA 40 Spindle exit : 125 mm Spindle speed: from 32 to 1600 RPM Table size: Length 1050 mm x Width 620 mm Manual table travel: 225 mm Table rotation at 360° Swivel table at +/- 30° Scale 3 axes ACU-RITE Sensory drilling Feeds spindle not working Clutch speed used Lubricant pump Voltage: 380 V Width: 2000 mm Depth: 2100 mm Height: 2500 mm Weight: 3 T

ID3532 FC Maschinenbau-Schlüsselbauer-Schindler year/Baujahr 1995/2010 Fully automatic stone finishing system (edge aging, bush hammering, impregnation) Fully automatic stone finishing system for the artificial processing of concrete block surfaces and edges, as well as for impregnation. The special feature of this system is that, unlike conventional processes, only the edges can be aged. Furthermore, the system also allows bush hammering of the stone surface. Fully automatic brick finishing system (stone edge aging, stick planting, impregnation) Fully automatic stone cutting system for the artificial processing of concrete block surfaces and edges as well as impregnation. The special feature of the system is that, in contrast to conventional processes, only the edges can be aged.  In addition, the system also allows the stone surface to be hammered. More details and price ...

Key data: 150 mm, 300 mm

Two Roll Rubber Mixing Laboratory Mill Manuf.: JRD Bipel 300mm x 150mm rolls Roller type bearings Nip fully guarded Motorised nip adjustment Roller speed variable up to 32 rpm Friction ratio 12:1 Grease lubrication Roller reverse system

For Sale: 2008 Deckel Maho DMC 70 H duoBLOCK Horizontal Machining Center - Year: 2008 - Make/Model: Deckel Maho DMC 70 H duoBLOCK - Type: Horizontal CNC Machining Center - Control: Siemens 840D - Features: - duoBLOCK design for high rigidity and precision - 5-axis capability - Automatic tool changer - High-speed spindle - Coolant system - Condition: Good, fully functional, under power Find more here - / Contact us at -

for all light/dark leftover breads etc. "the universal shredder" Model: RBZ 4 Stainless steel Capacity hrs./ 600 kg dry Strainer 5 mm ( included) Connection 400V, 4 kW, 16A-CEE plug Dimensions: 630 x 730 x 1455 mm, WxDxH Ejection height 455 Weight 70 kg New device 12 Months Warranty + Spare Parts Service Option: Leasing & Rental Service Other sieves Service Package Maintenance contract Instruction & Commissioning Visit our large bakery equipment exhibition!

Turning diameter 350 mm Turning lenght 550 mm Spindle speed 5000 rpm Bar work diameter 65 mm Controller MAZATROL smart

Capacity 200 kg/hour With the DLE Mini deleafer washing system

Two used GEA MIone Milking robot with equipments More details contact with us

1- one combination of lay-up, turning and unloading 2- BTF Multifoiler 3- Multi-Pin-System Useful area 1330x2630 mm Max size of board 1250x2550 mm Min foil width 1400 mm

Max. workpiece diameter 400 mm Max. workpiece length 800 mm Max. bar capacity diameter 80 mm Max. X-axis stroke276 mm Max. Z-axis stroke 755 mm Controller Siemens Spindle speed 4000 rpm With C axis

With C and Y axis Max. workpiece diameter 366 mm Max. workpiece length 708 mm Max. bar capacity diameter 105 mm Max. X-axis stroke 260 mm Max. Y-axis stroke 120 mm Max. Z-axis stroke 795 mm Controller Siemens

REF-2488 KOLBE MW32 MEAT MIXER GRINDER WITH 100 mm PLATE Meat mixer-grinder with product feed Manufacturer: KOLBE Model: MW32 Machine no.: 125277 Plate diameter: 100 mm (32) Main motor power: 5.5 kW/7.5 HP Mixer motor power: 1.1 kW/1.5 HP Overall dimensions: largo 1.150 mm, ancho 900 mm, alto 1.800 mm

Portal milling machine MARIO CARNAGHI

gebr. Chain mortiser HEMA Type: MC40 Year: 1995 Motor power: 2.2 kW (380V / 16A plug) Mortising depth: max. 180 mm Chain width: max. 40 mm Slot length: max. 230 mm Transverse stroke milling unit: 150 mm Table tilt: 45° Milling unit can be swivelled by 45° on both sides Weight: 350 kg incl. various chains and swords as shown 2 clamping levers have already been welded (see the last two pictures) Manufacturer

Engine Model: Masa 9001Vb Year of manufacture: 1992 Molds: 15 pieces Pallet size: 1400 x 1100 (900 pieces) Packagers -Rekers 1x Machine mixer Skako 0.75 m³ 1x Machine mixer Swissmade 0.5 m³ 2 conveyor belts (11 m)

Inv. Num. : 3483 Type: HELICHECK Producer: WALTER MASCHINENBAU Created: 2004 Parameters: The machine is in good technical condition and energized Accessories: Hydraulic clamps SK50

Multi-wire cutter with slat feed and chunk cutter 13 stones in NF format with three-sided chamfering. Batten length 1340 mm

Inv. Num. : 8314 Type: 42 BNA DHY Producer: Miyano Created: 2011 Parameters: Max. turning length: 235 mm Max. turning diameter: 80 mm Maximum spindle speed: 6000 1/min Max. rod diameter: 42 mm Weight: 3900 kg Equipment: IEMCA Bar Feeder

GeneralVertical Machining centre; Control: DMG MORI ERGOline X Multi-Touch control CharacteristicsTable surface900 x 600 mmTool Magazine with60 PositionsMovement X / Y / Z600/600/510 mmRapid feed X / Y / Z42/42/42 m/minSpindle speed range 20 to 12.000 rpmSpindle speed range 20 to 12.000 rpm AC main drive:13/9 kW (40/100% DC) Tool taper SK40 DIN 69871 Tool clamping according to DIN69872Direct measuring system X,Y,ZDirect Measuring System X, Y, Z inclusive Air Purge for Measuring SystemProduction Package 20 bar with chip conveyorProduction Package 20 bar with chip conveyor Option includes: - Internal coolant supply 20 bar - Chip conveyor (scraper type) with tank capacity: 200 l(left) - Bed flushing via M-Function - Coolant spray gun for swarf removal - External electronic handwheAir coolant internal (through spindle centre)Air Coolant Internal (through spindle centre) switchable via M-Func ...

GeneralVertical-Machining centre Stealth Design; Control: CELOS with Siemens 840D sl Operate Technical DataFeed rate longitudinal/transverse/vertical1-42000/1-42000/1-42000 mm/minRapid traverse longitudinal/transverse/vertical42/42/42 m/minWorking area 1Longitudinal1450 mmCross700 mmVertical550 mmTableTable surface 1760 x 750 mmMaximum load (table centre) 2000 KgSlot width 14 mmNumber of Slots 7Distance between T-Slots 100 mmSpindle speed 20.000 rpmMotor spindle speedMASTER® HSK-A63 Spindle speed 20 - 20,000 min-1 Output 35 kW / 25 kW (47 hp / 33 hp) Torque 130 Nm / 86 Nm (96 ft lbs / 63 ft lbs) (40 / 100 % duty cycle)Tool magazine 30 pockets HSK-A63Tool magazine 30 pockets HSK-A63 Chain magazine with pockets and with double gripper, incl. manually direct tool loading into the tool magazineInternal coolant supply package 40 bar / 600 lInternal coolant supply package 40 bar / 600 l conte ...

We are selling here a belt descaler from the manufacturer Maja, type ESB 441 in a good used and functional condition. Runs on 400 volts, bandwidth 37 cm, completely stainless steel, rollable, workshop tested, ready for immediate use, dimensions W/D/H 65/90/115 cm, others on request.