line sheet used for sale

Tetra Pak Tetra Therm Aseptic Visco Line for pasteurisation / sterilization of concentrated beverage bases by a Tubular Heat Exchanger (THE) system. Capacity 2.600 up to 8.150 liter per hour. At the current plant the line is used for products up to 100 °C. The indirect heating temperature is up to a maximum of 135 °C. Holding time set at 0 / 5 / 10 seconds. CIP Cleanable., In the Tetra Therm Aseptic Visco system, heating and cooling will take place in Tetra Spiraflo MTC tubular heat exchangers. Modules with a narrow ring section are used for heating and cooling to ensure optimal heat transfer. The product is pre-heated in stages within the Spiraflo tubular heat exchangers. The Spiraflo tubular heat exchanger is equipped with a sliding O-ring system. This means that the product and the outer tubes are not welded together. This prevents stress corrosion cracking and minimizes maintenance ...

The Waukesha Cherry-Burrell 015 is a rotary positive displacement pump which can handle dairy products (e.g., yoghurt, quark, curd and butter), solids (e.g., cherries and olives), slurries, pastes, and a variety of liquids. If wetted, they offer self-priming performance. A gentle pumping action minimizes product degradation. They also offer continuous and intermittent reversible flows and can operate dry for brief periods of time. Flow is relatively independent of changes in process pressure to, so output is relatively constant and continuous. Duo - twin wing stainless steel lobes. Nominal displacement: 0,054 liter per revolution. Maximum nominal capacity: 2,0 m3/h. Inlet / Outlet connection: 1-1/2. Maximum product pressure: 13,8 bar. Maximum pump speed: 700 rpm. The pump is used in a ice cream factory for product pumping. The current motor with this pump is 0,75 kW - 1,395 rpm - 380/420 ...

Tebel OST-IV Closed cheese vat of 8.000 ltr. Double jacketed for injection of steam or hot water so the temperature of the milk inside the vat can be indirectly adjusted. Stirring, cutting tools, welded to a horizontal shaft. This is driven by a drive unit with frequency converter. During cutting the tools rotate in the opposite direction as during stirring. The coagulum is cut by sharp radial knives of stainless steel. Whey can be drawn off through a perforated pipe (whey suction device). This pipe is lowered into the whey until it is only just immersed. The curd is discharged through the bottom valve. The vat is inclined (4%) toward the bottom valve to facilitate emptying. After a production run the vat is cleaned by four rotating CIP nozzles located in the top. All parts are made of stainless steel AISI 304 except the drive unit. Stainless steel MCC panel at the backside, close to the ...

Tebel OST-IV Closed cheese vat of 8.000 ltr. Double jacketed for injection of steam or hot water so the temperature of the milk inside the vat can be indirectly adjusted. Stirring, cutting tools, welded to a horizontal shaft. This is driven by a drive unit with frequency converter. During cutting the tools rotate in the opposite direction as during stirring. The coagulum is cut by sharp radial knives of stainless steel. Whey can be drawn off through a perforated pipe (whey suction device). This pipe is lowered into the whey until it is only just immersed. The curd is discharged through the bottom valve. The vat is inclined (4%) toward the bottom valve to facilitate emptying. After a production run the vat is cleaned by four rotating CIP nozzles located in the top. All parts are made of stainless steel AISI 304 except the drive unit. Stainless steel MCC panel at the backside, close to the ...

consisting of: automatic glass retraction, Fabr. HEGLA, Type: ISO, Ser No. 2033401055, glass washing and drying station, Fabr. LISEC, Type: VHW-F29/V8, YOC 2022, Ser-No. 315117/944, Glass transport station, Fabr. LISEC, Type: RTVB1527MZU2, Year 2019, Ser No. 383109341, visiting station, Fabr. LISEC, Type: RSV-38/27B, Year 2019, Ser No. 320-109338, Press Unit, Fabr. LISEC, Type: FPS-35/27U2, Year 2019, Ser-No. 343-109342, Frame Conveyor, Fabr. LISEC, Type: FR-400H, Year 2019, Ser-No. 550-109339, Dam system with sealing system, Fabr. LISEC, Type: VSL-10-27, Ser-No. 100170 with 2 stowage sections, dead weight: 4500 kg, as well as separate control/control cabinet system with cooling system, Fabr. RITTAL, control unit, dosing unit, pump and valve technology, max. working height of the system: 2700 mm

consisting of: 8 large shelves, Fabr. HEGLA, type: FLB, load capacity: 40,000 kg each, for lengths up to: 6,000 mm, tilting table/glass support, Fabr. HEGLA/HAGER, year 1988, Ser no. 0880342, Floatglasschneid- u. Brechtisch, Fabr. HEGLA, cutting bridge, Fabr. HEGLA, type: OPTIMAX 6032ES, built in 1996, Ser no. 6079, Net weight: 6,500 kg, Storage table, Table surface: approx. 3200x6000 mm, with operating terminal, PC tower, monitoring monitor, lattice enclosure and light barrier system

consisting of: tilting table, Fabr. HEGLA, type: ART6032, built in 2005, Ser no. E7662, net weight: 3,900 kg, surface layer unit, cutting table with cutting bridge, Fabr. HEGLA, type: VSG A46-MT, year 2003, Ser-No. 2118, footprint: approx. 3200x7000 mm, dead weight: 11,000 kg, max. working pressure: 6 bar, with control unit, lattice housing and light barrier system

Complete falling film vacuum evaporator, previously used for skimmed milk or sweetened whole milk, consisting of a 4 effect TVR Evaporator. Still mounted in the cheese plant in Spain till end of April 2026. The product feed rates in the installation are ± 14 t/h with a comparative temperature between 73 and 50°C from the 1st to the 4th effect., Processing rates used by the current plant for skimmed milk:, - Infeed flow: 14.000 kg/h @ 9% DM, - Infeed temperature: 5 °C, - Water Evaporation: 11.375 kg/h, - Outfeed flow: 2.625 kg/h @ 48% DM, - Steam consumption: 2.050 kg/h, Processing rates used by the current plant for sweetened whole milk:, - Infeed flow: 14.000 kg/h @ 25% DM, - Infeed temperature: 5 °C, - Water Evaporation: 7.637 kg/h, - Outfeed flow: 6.363 kg/h @ 55% DM, - Steam consumption: 1.375 kg/h, Approximately operating temperatures:, - First effect (steam side): 73 °C, - Fir ...

Line for painting door glass, consisting of: - automatic loader with flap arm equipped with LOGLAS 16.30 suction cups - automatic loader with bridge structure, programmed picking on LOGLAS/CL 16.30 trolleys - automatic oscillating spraying machine FALLENGLASS 1700 - year 2007, with belt conveyor covered with paper, complete with inlet roller conveyor extension with oscillating and ionizing blower unit - PRE-HEATING OVEN in-line with lower infrared lamps PRE/I-NIR - 180° sideshift with ventilated transversal flash-off oven with CEFLA GT180/3400/5500 air-heating coil - in-line drying oven with hot air and infrared lamps GLASSOVEN EL/7 - year 2007 - cooling tunnel with upper and lower air curtains CEFLA GLASSCOOL SI-3/3 - year 2007 - motorized conveyor VTR 2500 - automatic unloader on trolleys with CEFLA bridge structure UNLOADER -WASHING MACHINE NOT PRESENT- Auction-ID: A7-454 ...

Condition: Used Stock Number: 875B Marel Masterslice Type: TA1511 Marel Masterslice Serial number: 10090783 Marel Masterslice Year of construction: 2011 Marel Masterslice Outfeed conveyor 170 mm wide Marel Masterslice Dimensions: 2100 x 1000 x 1500 mm Marel Masterfill Type: TA1516 Marel Masterfill Year of construction 2011 Marel Masterfill Dimensions: 1000 x 750 x 1200 mm

Longitudinal cutting line for sheet metal coils, consisting of: - 1 decoiler with loading trolley - 1 cutting head - 1 hole passage table - 1 pneumatic press with felt - deburring rollers - 1 x 1-arm discharge flag EXCLUDING trim winder Technical data: Maximum cutting width 1200 mm Strip thickness from 0.30 mm to 1.20 mm Line working speed 180 mt/min Maximum coil weight 6,000 kg Coil OD up to 1200 mm Electrical panel upgraded in 2016 DOCUMENTS, MANUALS and LAYOUTS NOT AVAILABLE MANUFACTURER, MODEL AND DATE OF CONSTRUCTION NOT DETECTABLE MACHINE NO CE Auction-ID: A7-45688-1

Overview This PET filling line was manufactured between 1996 - 2019 by several European manufacturer. The line is designed for carbonated beverages such as lemonades and also suitable for water with or without CO₂. With an output capacity of 14.000 bph, it offers a complete solution from bottle blowing to palletizing. This equipment is in good condition and still fully operational.   Technical Data Capacity: 14.000 bph Filling product: carbonated water and soft drinks  OPP wrap-around label from a reel with hotmelt and glue labelling station Packaging formats: shrink wrapping without tray Pallet: Euro pallet (1.200 x 800 mm)  condition: good technical condition, still in production Scope of Delivery Blow moulding machine | Sidel | SBO10 | 2010 Elevator preform | Sidel | 2010                                                                         ...

Compact roll line WP Rollprofi Year of Make: 2005 Condition: repaired, cleaned & checked Suitable for the production of sliced rolls, smooth rounds, long-rolled rolls and double pieces Weight range: 30-85 g Hourly output: max. 3,750 pieces 4-row system with 600 mm working width Integrated dough divider and drum rounder, Multimatic Pre-proofing time 12 min (6 min in front of long roller station and 6 min between long roller and cutting station) Hanging drying Maintenance-free suspension chain with automatic tensioning Variable depositing device for digestate carriers of the 3

Pastry line Seewer Rondo SPF 602 Condition: used, functional Year of Make: 2000 Calibration head, built in 1996 Cutting station Sprayer Filling station Guillotine Incl. cutting tools

Bulk of food packaging Premium LINE, disposable knives, forks, spoon cups, cups, salad bowls, bowls, sausage plates, aluminium packaging, bowls with lids, soup bowls, paper plates, coffee cups, coffee spoons, chicken bags and delicatessen bags Auction-ID: A7-45677-107

Meiko Rinsing Line + Disinfection - Automatic Topline 40, Year 2020 unused! With dishwasher + 3 spout basins, ready to connect, VDE tested Auction-ID: A7-45677-83

Meiko Dishwashing Line + Disinfection - Automatic Topline 40, built in 2020, with a spout basin + sink base cabinet + wall shelf, ready to connect, VDE tested Auction-ID: A7-45677-85

Overview  This fully automatic packaging system for jars was built by Buhmann pac solutions System GmbH in 2016 and has been used very little, with only approx. 5,000 operating hours (of which approx. 2,000 hours were in pure production operation). The line includes a carton erector (wrap-around trays) and a packing unit and, in addition to packaging single-type cartons, also offers the option of automatically mixing offline products (mixed cartons). The system was regularly maintained by Buhmann & Yaskawa, with around €200,000 invested in maintenance and servicing between 2020 and 2024. The system is in very good condition and is available immediately. Technical details  Performance Product infeed online: max. 280 jars/min Format 3: max. 220 jars/min Mix type A: max. 140 jars/min (11.5 cartons/min) Mix type B: max. 140 jars/min (11.5 cartons/min) Total output: max. 350 jars/min or 3 ...

2018 Dr. Collin ZK 16 Twin-Screw Lab/Pilot Polymer Extrusion Line Overview Excellent opportunity to acquire a complete, high-quality laboratory/pilot extrusion line manufactured by Dr. Collin GmbH, an industry leader in R&D and polymer processing equipment. Built in 2018, this co-rotating twin-screw extrusion line (ZK 16 model) is specifically designed for processing plastic materials in small batches, making it ideal for research and development, testing, compounding, and new formulation development. Key Technical Specifications Manufacturer: Dr. Collin GmbH – Lab & Pilot Solutions Model: ZK 16 (Twin-Screw Extruder) Year of Manufacture: 2018 Condition: Used (Dismantled and ready for transport) Screw Diameter: ~16 mm (Co-rotating twin-screw) Power: 8 kW Voltage/Current: 400 V + N + PE / 15 A / 3~ 50 Hz Operating Pressures: Water: 4 bar / Compressed Air: 4 ...

CMT Cheese Stretching and Moulding Line . CMT FL 1400 / Boilers/ Tanks/ Moulding / Extruding . CMT Cheese Cooking, Stretching and Moulding Line Screw Hopper for Cheese Transfer Moulding Machine with 2 Sets of Moulds Boiler and Hot Water Tanks Control Panel Manual Book Technical Manual Condition : Good Location :, Use: Cheese Cooking, Stretching and Moulding

A complete Groninger bottle filling line is available. 1) Bottle unscrambler Groninger ZSB 2000, year of manufacture: 1995. 2) Filling machine Groninger DFV 1000Q, year of manufacture: 2013, filling stations: 10, additional function: transverse transfer system, output: approx. 9000/h, dosing range: 5ml-1000ml, container height range: 30mm-250mm, transport cup dimensions X/Y: 108mm/80mm, operating hours: approx. 24100h. 3) Cap sorter Groninger ZSK 1500, year of manufacture: 1995, sorting disc speed: 25rpm. 4) Capping machine Groninger KVK 106, year of manufacture: 1995, max. capping output: 9000/min, max. container diameter: 100mm, max. container height: 200mm, machine dimensions X/Y/Z: approx. 3400mm/1450mm/2550mm, weight: approx. 1500kg. 5) Discharge conveyor Groninger, year of manufacture: 1995. Documentation available. An on-site inspection is possible.

Overview  This complete PET water bottling line was manufactured on average in 2006 by European manufacturers including Siapi, Melegari S.p.A, P.E Srl, So.Te.Ma.Pack, Comag, TMG, Domino and Atlanta. The line will remain in production until the end of June 2025, offering the possibility to see it live in operation. All equipment is in very good working condition with complete maintenance history, making it an immediately operable turnkey solution. Technical data  Capacity: up to 6,800 b/h for 0.5L bottles, up to 6,000 b/h for 1.5L bottles Formats: 500ml PET, 1500ml PET Neck finish: 30/25 Packing: 500ml bottles: 24-pack shrink film 1.5L bottles: 6-pack shrink film Bottle diameters: 203mm (0.5L), 317mm (1.5L) Equipment condition: very good, complete maintenance history available Scope of Delivery Blow molding machine: Siapi EA4 Filling machine: Melegari S.p.A Fill Jet 20/20/4 Labeling mac ...

LINEA ESTRUSIONE PER TUBI Estrusore monovite diametro 60 L/D 30 motore A/C 100 kW Testa di estrusione per tubo diametro 13,25 mm nr.2 viti di ricambio usate nr.2 vasche raffreddamento con pompe acqua e spruzzatori nr.2 vasche di raffreddamento statiche Marcatrice Citronix Traino a cingoli contrpposti Avvolgitore doppio PM Imnpianti nr.2 Viti usate di scorta

LINEA GRNAULAZIONE PER FILM Silos alimentazione foglia Diametro vite 130 L/D 35 Nr.1 degassaggio Potenza motore 243 kW Cambiafiltro a piastra idraulico Taglio in testa ad anello liquido Centrifuga Vibrovaglio Ventola estrazione materiale

ESTRUSORE BIVITE PER RIGENERAZIONE VITI DIAMETRO 140 L/D 32 ALIMENTAZIONE FORZATA CARICATORE LATERALE CON SISTEMA DI PESATURA PLC ERGOMEC ANNO 2012 TAGLIO IN TESTA AD ANELLO LIQUIDO FILTECH GRO 1000 VIBROVAGLIO SILOS ALIMENTAZIONE

LINEA DI ESTRUSIONE PER TUBI PPR - NR.2 ESTRUSORI DIAMETRO VITE 75 L/D 37 - NR.1 COESTRUSORE DIAMETRO VITE 30 L/D 25 - NR.1 TESTA ESTRUSIONE CON FILIERA PER TUBO 40 MM - NR.2 VASCHE DI CALIBRAZIONE MODELLO KVT 125 - NR.2 VASCHE DI RAFFREDDAMENTO MODELLO KST 125 - TRAINO A CINGHIE CONTRAPOSTE KH 125 - TAGLIERINA PLANETARIA KC 125 - RIBALTA PROFILI

IMPIANTO RIGRANULAZIONE BIVITE Taglio ad anello liquido Forties T 1000 anno 2016 Alimentazine forzata con quadro c. eletric

LINEA RIGENERAZIONE MONOVITE Diamtero vite 120/210 conico L/D 36 n.1 Degasaggio Silo alimentazione Cambia filtro a piastra Taglio ad anello liquido Vite di scorta

DOWNSTREAM COMPLETO GREINER ANNO PRODUZIONE 2008 BANCO CALIBRAZINE DOPPIO MODELLO get.CAL 11,2– 5P/4Z – DUAL A TRAINO CON TAGLIERINA DOPPIO MODELLO get.COM 30/9-235-S/500 BANCO RACCOLTA PROGFILI DOPPIO MODELLO GTT 6,0

LINEA COMPLETA PER PROFILI ESTRUSORE MONOVITE DIAMETRO 90 BANCO DI CALIBRAZIONE CON VASCA DI CALIBRAZIONE TRAINO A CINGOLI TAGLIERINA RIBALTA PROFILI

LINEA RIGENERAZIONE MONOVITE Diamtero vite 120/210 conico L/D 36 n.1 Degasaggio Silo alimentazione Cambia filtro a piastra Taglio ad anello liquido Vite di scorta

LINEA COMPLETA PER TAPPARELLE IN PVC Turbo miscelatore da 80 L Estrusore bivite diametro 57 L/D 22 Nr.1 Degassaggio Banco calibrazione Traino a cingoli contrapposti Punzonatrice per tapparella Taglio a sega Banco raccolta profili

LINEA GRNAULAZIONE PER FILM Silos alimentazione foglia Diametro vite 130 L/D 40 Doppio degasaggio Motore A.C 280 kW Cambiafiltro a piastra idraulico Taglio in testa ad anello liquido Centrifuga Vibrovaglio Ventola estrazione materiale

ESTRUSORE PRINCIPALE EA100/52D CO-ESTRUSORE EA48/40D CAMBIA FILTRI A PIASTRA POMPA INGRANAGGI TAGLIO AUTOMATICO TA100 AVVOLGITORE A 2 STAZIONI CON TRAINO CATTORINI Materiali lavorati: HIPS-ABS-PP (fatto dei test positivi anche con PLA) Spessore minimo 37/100, Spessore massimo 150/100

LINEA RIGENERAZIONE MONOVITE ESTRUSORE DIAMETRO 105 CON CAMBIA FILTRO E TESTA A SPAGHETTI NR.1 DEGASAGGIO VASCA DI RAFFREDDAMENTO AD ACQUA STATICA TUNNEL DI ASCIUGATURA AD ARIA TAGLIERINA PER SPAGHETTI VIBROVAGLIO BECCARIA STRUTTURA PORTA BIG-BAG

LINEA DI RIGENERAZIONE PER FILM PE ESTRUSORE DIAMTERO 130 L/D 35 NR.1 DEGASAGGIO ALIMENTAZIONE FORZATA SILOS ALIMENTAZIONE FOGLIA CAMBIA FILTRO A PIASTRA DIAMETRO 200 TAGLIO IN TESTA ORIZZONTALE QUADRO DI COMANDO

IMPIANTO RIGRANULAZIONE MONOVITE Silo alimentazione Diamtero vite 130 L/D 37 n.1 Degasaggio Alimentazione forzata Cambia filtro a piastra BD Plast Vite di scorta revisionata

LINEA RICICLO PLASTICA TANDEM - NASTRO TRASPORTATORE CON METALDETECTOR - TRITURATORE GM 125 AF/T - ESTRUSORE MONOVITE GM 125/28D - DOSATORE MASTER DPM 15/50, gm 125, CACO3 DPM 2V SPC - CAMBIA FILTRO FIMIC RS 500 - CAMERA SOTTO VUOTO DEL SISTEMA DEGASSAGGIO - ESTRUSORE MONOVITE SECONDARIO GM 140/18D - CAMBIAFILTRO A PIASTRA GM125/200 MF - TAGLIO AD ANELLO LIQUIDO TDA 6.0 - VIBROVAGLIO VB 200

LINEA COMPLETA PER ESTRUSIONE TUBO NR.1 ESTRUSORE BATTENFLED V63 NR.1 COESTRUSORE TECNOMATIC NR.1 TESTA ESTRUSIONE PER TUBO DA 20 MM NR.1 VASCA CALIBRAZIONE BETTENFELD V63 NR.2 VASCE BATTENFELD K63 NR.1 TRAINO KUATRO PLAST KH63 NR.1 TAGLIERINA PLANETARIA GRAEWE STS 125 NR.1 RABALTA PROFILI

Line has got 2 throughfeed drilling machines Weeke 1st drill Weeke BST30/25, N? 0-259-05-3283-01-0810, 1992 Equipment: 2 x hor. Units, split drilling blocks, each with motor 1,8 kW, 13-spindle drilling blocks, centers 32 mm 6 x bottom unit, split drilling blocks, each with 1,8 kW motor vertical blocks swivelling 360? Min/max motor centerdistance: 160 - 576 mm Min drilling unit center distance: 192 mm Preselection for automatic cycles Panel sizes, length 250 up to 2500 mm, width 200 up to 800 mm, thickness 12 up to 40 mm 2nd drill Weeke BST30/25, N? 0-259-05-3284, 1992 Equipment: Machine prepared to take 2 horizontal units at later date 6 x bottom unit, split drilling blocks, each with 1,8 kW motor vertical blocks swivelling 360? Min/max motor centerdistance: 160 - 576 mm Min drilling unit center distance: 192 mm Preselection for automatic cycles Panel sizes, length 250 up to 2500 mm,  ...

machine 1: Fixed side at the left, working width 220 mm to 2500 mm Workpiece overhang max. 110 mm Electronic width adjustment Panel thickness 8 - 90 mm Top pressure by belts Rolling chain with automatic lubrication, automatic pop-up dogs every 1000 mm Feed speed 10 - 40 m/min Chain infeed taking 1,62 m. panels in front of the dogs Panel alignment at the infeed Middle support NC 30 controlls Equipment left and right: 1+1 Jump universal shaper 6 kW 1+1 Twin hogging unit, motors 6,6 kW (2 motors) 1+1 Universal shaper 6 kW 1+1 Jump universal shaper 6 kW panel turning device HOMAG TD 31/30/13 Year 1989 machine 2: Fixed side at the left, working width 220 mm to 3000 mm Workpiece overhang max. 110 mm Electronic width adjustment Panel thickness 8 - 90 mm Top pressure by belts Rolling chain with automatic lubrication, automatic pop-up dogs every 1000 mm Feed speed 8 - 40 m/min Chain infeed taking ...

drilling machine for drilling holes at pre-programmed distances. The machine is fully operational and ready for use. working area: 4000 cm Auction-ID: A7-45896-3

This 3-axis WEINIG / DIMTER Unirex 2000 SPB was manufactured in 2007. It features a total power of 45 kW and operates at a nominal current of 110 A. The machine is part of a comprehensive wood production line, including a drilling and milling center, tenon cutting machine, and longitudinal profiling machine. If you are looking to get high-quality wood processing capabilities, consider the WEINIG / DIMTER Unirex 2000 SPB machine we have for sale. Contact us for further details.

Wood production line manufactured in 2023. This ISM ATM-01 is a custom-made automatic production line designed for the fully automated manufacturing of wooden garden screens from individual planks. It features automatic discharge and stacking of finished screens, tilting stacks for efficient processing, and is adjustable for five different screen types. If you are looking to get high-quality wood processing capabilities, consider the ISM ATM-01 machine we have for sale. Contact us for further details.

Wood production line manufactured in 2017. This BURKLE Optima 1428/50 includes a continuous-action stack press with a pressing area of 1400 x 2800 mm and an automatic feeding system. It also features a robust panel rack and two tilting hoppers with a capacity of 1.5 m³. If you are looking to get high-quality door panel production capabilities, consider the BURKLE Optima 1428/50 machine we have for sale. Contact us for further details.

Continuous Butter Line which exist out of a Continuous Butter Making Machine (CBM) + Butter silo + Bulk Packer. The line has a production output capacity up to 6.000 kg of butter per hour. It operates with an input of approximately 12.000 liters of cream per hour. All product-contact parts and the frame constructed from stainless steel. It is CIP-cleanable for hygienic operation., - Continuos Butter Machine (CBM):, Manufacturer: GEA Westfalia, Model: BUD 6000, Year: 1996, Condition: Used, Serial Number: 1715 18L, Capacity, butter output: up to 6.000 kg/h (depends on product), Capacity, cream infeed: ± 12.000 kg/h, Including:, - Vacuum pump., - Brine dosing system., - Cream tank., - Cream pump., - Cream pre-heater., - Interconnecting piping, valves, flow indicators etc., - Control panel with Siemens S7 PLC and operating panels., Additional a Wal, moisture control system is integrated in  ...

Wood production line manufactured in 2004. This CEFLA Spraybotic MD features an automatic spray arm with 4 spray heads and a pump station equipped with 5 Graco coating pumps. The passage width is approximately 1350 mm, making it suitable for various coating applications. If you are looking to get high-quality coating capabilities, consider the CEFLA Spraybotic MD machine we have for sale. Contact us for further details regarding this machine.

Used root vegetable washing and peeling line with a capacity of about 5 T/h The line includes: DRUM WASHER WITH ELECTRIC MOTOR. - TYPE LTJ-840 DL.3600,WIDTH 1100,H.1950, Manufacturer: GATINEAU FRANCE, Year: 1980 Flat conveyor SCREW POWER PEELER WITH MOTOR. ELECTR. - TYPE YAI1056 BE A6/1 DL.5200, Manufacturer: GATINEAU FRANCE Year: 1980 STEAM PEELER WITH MOTOR. ELECTR. - TYPE PVR-900L DL.3000,WIDTH 2000,HEIGHT 5750, Manufacturer: GATINEAN FRANCE Year: 1980 OUTPUT SCREW WITH PEELER WITH ELECTRIC MOTOR - TYPE YAI 1056 BEA4/1 DL.7500, Manufacturer: GATINEAU FRANCE Year: 1980 Brush wipes 2pcs Inspection Conveyor

-Storage racks with 6 different diameters. -Automatically driven roller conveyors, fully automatic length stop, automatic ejection in pre-sorting compartments. -PLC control for convenient machine control. -Blade width of hydraulic machine : 150mm. -Capacity: 5 to 15Ton per day/shift. -Low maintenance & wear parts, still in perfect working condition with no known problems. Sale due to cessation of internal production. DBS3 automatic double bender. -Linked with cutting line. Equipped with hydraulically controlled roller conveyor, automatic transfer system, automatic double bender and ejection system in automatic pre-sorting compartments. -Simple PLC control, equipped with automatic clamping system. -Low maintenance & wear parts, still in perfect working condition with no known problems. Sale due to cessation of internal production. Auction-ID: A3-43515-16394

Qty. 1 Second-hand Hot Rolling Mill Line Manufacturer: NKMZ Built: 1972 Roll Force: 2300 T (Periphery roll speed)Mill Speed: 0-24-210 m/min. Slab Thickness: 300-350 mm Width: 740-1540 mm Length: 1100-3000 mm Slab Weight: 1-2.7 T Slab Temperature: 370 – 550 °C Rolled Thickness: 8-200 mm Width: 750-1550 mm Plate Length: 2000-8000 mm Coiled Thickness: 6 – 12 mm Coiled Width: 700-1550 mm Coil I.D./O.D.: 750/1400 mm Coiling Temperature: 300-350 °C Back-up Rolls Dia.: 1500 – 1400 mm Work Rolls Dia.: 800 – 760 mm Roll Barrel Length: 1800 mm