light used for sale

GIUSTI GMP Pharmaceutical quality mobile liquids vessel in polished finish 316 grade stainless steel. 750mm dia x 980mm deep including bottom hemispherical base. Gross capacity approx 350 litres to flange. 25mm dia bottom outlet with valve. 210mm high top dish with 130mm lightglass and light, 4 bar pressure gauge, pressure relief valve, 80mm dia chargeport with hinged cover, 3 off 25mm dia connections with valves, all hygienic quality fittings. Mounted onto a stainless mobile base with castors. Base width 860mm, flange dia 920mm this extra information is standard for this model. Please always double-check the details during a visit The Giusti 300 Litre Vessel stands as an exemplary liquid mixer in pharmaceutical manufacturing, offering unparalleled quality and efficiency. Constructed from polished 316-grade stainless steel, this vessel adheres to GMP pharmaceutical standards, ensur ...

Romaco Fryma Koruma Dinex process mixing vessel suite in UNUSED condition comprising of the following:- Main Process Vessel: 1300L scraped wall, contra rotating, jacketed, full vacuum +6bar. Bottom entry homogeniser mounted in vessel base unit which also houses the hydraulic raise/lower powerpack for the vessel lid, vacuum pump, centrifugal CIP pump, shrouded in stainless steel. 8 off top connections and level sensor, 300mm dia hinged safety interlocked chargeport with sightglass and light. Scrape wall mixer 5kw, contra rotating mixer 4kw. 45kw 2865rpm homogeniser. Additional vessels: 1300L jacketed premix vessel on load cells, scraped wall mixer with baffles. 400mm dia safety interlocked hinged chargeport with sightglass and light. 4 off top entry infeed connections, 3 stainless steel lobe pump mounted onto vessel framework, 4 outlet with pneumatic actuated valve. 100L powde ...

Suitable for fully automatic and touch-less measuring of cutting tools of all kinds. By means of 2 CCD matrix cameras, reflected-light and transmitted light measurements are performed. For example diameter, length, angles, spiral angle, spiral length, clearance angle, cutting angle etc. can be measured. Accessories:, Pneumatic workpiece clamping,, Windows 7 PC + QCM 8.0, software VIALOGIC TIM Teach-In-Mode,, software package 1 (cylindrical tools sharp edge, corner and full radius),, software package 2 ( conical-spiral tools sharp edge, corner and full radius),, Software VIALOGIC Viascan,, QCM Network,, LightControlDevice,, Glass scales on the linear axes., Traverse X-axis: 200 mm, Y-axis travel: 350 mm, Z-axis travel: 250 mm, A-axis speed: 60 rpm, Workpiece holder: ISO 50, Workpiece diameter: 3 - 200 mm, Workpiece length: Max. 300 mm, Workpiece weight: max. 40 kg, Connected load: approx. ...

Max. Laser power: 400W, operating hours: 28. 200h, with WinLas laser programming software, storage option for 99 laser programmes Optical setup for one laser light cable with fast switch (50ms switching time), optical setup can be extended to a maximum of 4 laser light cables, pilot laser with plasma sensor holder, Control of the pilot laser via laser operating software, beam guidance and shaping, LLK-B 06 laser light cable, length 40m, fibre diameter 600mm, suitable for robots, BEO 7000210p processing optics for laser welding, lens with focal length 200mm, Protective glass cassette for easy replacement of the protective glass, collimation 0° with defocussing and observation by camera, CCD camera, b/w monitor, adjustable crosshairs, camera supply cable, 30m long, and BNC video cable, 10m long, optics protection by Laval Crossjet, Design of the robot cell with suspended robot, KUKA KR 30 ...

Specifications / Technical data S-1000/T Portalfraesmaschine / Engraving machine With the T-variant of the High-Z CNC-Fraese you acquire old-fashioned technology with the certain i-tuepfelchen in TUeV-certified quality (Emc). The High-Z/T Fraese is designed for even more accuracy (repeatability about 0.01mm ) and especially for higher travel speeds. Through the ball-circuit spindles used, the High-Z/T achieves fantastic accuracy and an almost unmeasurable reverse play of about 0.01mm. At the same time, high travel speeds of up to approx. 108mm / second ( 6500 mm / minute ) can be achieved. This is how engraving and fraes speeds of up to approx. 4500mm/min can be realized and urgent journeys up to approx. 7000mm/min. Here you can see a video about empty runs with the new high-Z/T 3D CNC machine. This makes this machine series in the industrial sector just as applicable for work ...

CNC portal fraese and 3D engraving machine T-Rex 0712: equipment / product data of cnc-Fraesen Type High-Z/TRex series: Drive: 3 busiest brand stepper motors with 4.5 amperes. Pushing through long and up to 120mm high materials possible, as no belt drive is in the way at the end of the X axis! linear guides on all Y axes from HIWIN / THK ! Multiple ball-bearing ball thread spindles on all axes, brand make! Rapid speed max. approx. 17,000 mm/min working speed max. approx. 12,000 mm/min Technical platform X/Y: 0.005mm (1/10 step); Z: 0.0025mm reverse play maximum approx. +/- 10microns (0.010 mm) Point repeatability: approx. 0.01 mm clamping area of the groove plate / T-slot table: 1650 x 880 mm travel distances: X=1200mm; Y=700mm; Z= 130 mm contact contact sensors / reference switches / limit switches on all axes Double secured emergency release energy chains for cle ...

Specifications / Technical Data S-400 Fraes machine / engraving machine With the High-Z CNC-Fraes.- and engraving machine you acquire an all-round talent in TUeV-certified quality (EMC). Whether you want to clamp complex parts on a groove table or, or put factory tins in a high vice (the machine is on a frame construction, is driven in X via 2 motors and thus allows to be placed completely over a part to be machined). or simply want to do engraving or drilling then they simply work on a flat base, on which they then attach e.g. an MDF plate, which they once overfrave plan and are then able to work up to approx. +-0.02mm exactly in depth. All machines are supplied with coloured energy chains on all axes due to improved cable guidance. Furthermore, all machines are protected with a double-secured emergency exit button. Another is located directly at the controller. Basic equip ...

Specifications / Technical Data S-1000 CNC-Fraese and Engraving Machine The almost largest CNC machine of the high-Z series in TUeV-certified quality (EMC). With an external dimension of approx. 1350 x 800mm still handy enough and extremely powerful. With the high-z CNC unit, they acquire an all-round talent. Whether you want to clamp complex parts on a groove table or, or clamp the factory into a high vice (the machine stands on a frame construction, is driven in X via 2 motors and thus allows to be placed completely over a part to be processed). Or just do engraving or drilling then they simply work on a flat surface, on which they then attach, for example, an MDF plate, which they once plan overfraes and are then able to work exactly in depth up to approx. +/- 0.02mm. All CNC portal fraes machines are supplied with coloured energy chains on all axes due to the improved cable ...

CNC Router and 3D engraving machine T-Rex 0712: Equipment / product data CNC-milling machine type High-Z/TRex series: Drive: 3 brushless brand stepping engines with 4,5 ampere. Possibility of sliding through long and up to 120mm high materials, no belt drive at the ende of the X axis! Linear guide on all axis by HIWIN / THK ! Multiple ball-bearing ball-screw spindle on all axes, proprietary brand! Rapid traverse max. ca. 17.000 mm/min Operating speed max. ca. 12.000 mm/min Technical definition X/Y : 0,005mm (1/10 Schritt); Z: 0,0025mm Backlash maximal ca. +/- 10µm (0,010 mm) Repeat accuracy: ca. 0,01 mm Clampin surface of grooven panel / T-slot table1650 x 880 mm Travels: X=1200mm; Y=700mm; Z= 130 mm Non-contact reed sensors / reference switches / limit switches on all axes Double secured emergency-stop button Energy chains for a clean cable routing Total dimensions  ...

Equipment / Product data of the CNC-Fraesen Type High-Z/TRex series / Type 1215 Drive: 3 busiest brand stepper motors with 4.5 amperes. Pushing through long and up to 120mm high materials possible, as no belt drive is in the way at the end of the X axis! linear guides on all axes of HIWIN / THK ! Multiple ball-bearing ball thread spindles on all axes, brand edging! speed speed max. 12,000 mm/min Working speed max. approx. 8,000 mm/min Technical platform X/Y: 0.005mm (1/10 step); Z: 0.0025mm reverse play maximum approx. +/- 10 microns (0.010 mm) Point repeatability: approx. 0.01 mm clamping area 1860 x 1340 mm travel distances: X=1500mm; Y=1200mm; Z= 130 mm contact contactno-point sensors / reference switches / limit switches on all axes Double-secured emergency trigger energy chains for clean cable Total mass with motors : LxWxH approx. 2180 x 1800 x 1420 mm Fra- Sc ...

3D CNC Router T-Rex 1215 / Technical Data : Equipment / product data CNC-milling machine type High-Z/TRex series: Drive: 3 brushless brand stepping engines with 4,5 ampere. Possibility of sliding through long and up to 120mm high materials, no belt drive at the ende of the X axis! Linear guide on all exis by HIWIN / THK ! Multiple ball-bearing ball-screw spindle on all axes, proprietary brand! Rapid traverse max. ca. 12.000 mm/min Operating speed max. ca. 8.000 mm/min Technical definition X/Y : 0,005mm (1/10 Schritt); Z: 0,0025mm Backlash maximal ca. +/- 10µm (0,010 mm) Repeat accuracy: ca. 0,01 mm Clampin surface of grooven panel / T-slot table 1860 x 1340 mm Travels: X=1500mm; Y=1200mm; Z= 130 mm Non-contact reed sensors / reference switches / limit switches on all axes Double secured emergency-stop button Energy chains for a clean cable routing Total dimensions wi ...

Equiptment / product data CNC-milling machine type High-Z/TRex series / 1224 Drive: 3 brushless brand stepping engines with 4,5 ampere. Possibility of sliding through long and up to 120mm high materials, no belt drive at the ende of the X axis! Linear guide on all axis by HIWIN / THK ! Multiple ball-bearing ball-screw spindle on all axes, proprietary brand! Rapid traverse max. ca. 12.000 mm/min Operating speed max. ca. 8.000 mm/min Technical definition X/Y : 0,005mm (1/10 Schritt); Z: 0,0025mm Backlash maximal ca. +/- 10µm (0,010 mm) Repeat accuracy: ca. 0,01 mm Clampin surface of grooven panel / T-slot table 2800 x 1340 mm Travels: X=2400mm; Y=1200mm; Z= 130 mm Non-contact reed sensors / reference switches / limit switches on all axes Double secured emergency-stop button Energy chains for a clean cable routing Total dimensions with engines : LxBxH ca. 3070 x 1800 x  ...

Specifications / Technical data S-400/T CNC-Portalfraesmaschine / Engraving machine Granite, marble, slate, soapstone engraving, photoengraving, fraesen... With the T-variant of the High-Z CNC-Fraesmachine you acquire old-guarded technology with the certain i-Tuepfelchen in TUeV-Qualitat. The High-Z/T is designed for even more accuracy (repeatability about 0.01mm ) and especially for higher travel speeds. Through the ball-circulation spindles used, the High-Z/T CNC-Fraes machine achieves a fantastic accuracy and an almost unmeasurable reverse play of about 0.01mm. At the same time, high travel speeds of up to approx. 108mm / second ( 6500 mm / minute ) can be achieved. This means engraving and fraes speeds of up to approx. 4500mm/min can be realized and urgent journeys up to approx. 7000mm/min. Here you can see a video about empty journeys with the new High-Z/T. This makes t ...

Bearing platform 4,000 x 15,000 mm, load capacity 500 kg / m2 Included in the scope of delivery are: 4 stands, one side 100 x 100 x 3 mm 4 stands, double-sided 100 x 100 x 3 mm 6Main carrier C+300 x 3 x 4,190 mm 15 cross member S+300 x 2 x 4,800 mm 30 Mounting angle 4 Cross Associations 27 chipboard P6, 3000 x 850 x 38 mm, UK white, OK natural UK white, OK nature incl. fastening material incl. load signs Dimensions, technical data Steel construction: 4,000 x 15,000 mm Floor area: approx. 60 sqm Height top edge floor covering: up to 3,500 mm freely selectable ( other heights on request ) light height underside: OK minus 338 mm Capacity: 500 kg / m2 Columns: 100 x 100 x 3 mm Main carrier: C-Profile C+300 x 3 mm Cross member: Sigma profiles S+300 x 2 mm Flooring: 38 mm chipboard, white on one side Columns in the following standard colors: Ral 7035,  ...

Bearing platform 8,000 x 5,000 mm, load capacity 500 kg / m2 Dimensions / technical data Dimensions steel construction: 8,000 x 5,000 mm Dimensions floor area: 8,000 x 5,000 mm Floor area: approx. 40 m2 Height OK floor ingesis: up to 3,500 mm (freely selectable) light height underside: Ok minus 338 mm net load capacity: 500 kg / m2 same-distributed load Included in the scope of delivery are: 6 steel tube supports 100 x 100 x 3 mm 4 main beams C+300 x 3 x 3,990 mm (perforated) 9 cross beams S+300 x 2 x 4,800 mm (closed) 18 Mounting angle 3 Cross Associations 18 chipboard P6, 3000 x 850 x 38 mm, UK white, OK natural incl. fastening material incl. load signs Stand optionally in the following standard colours: Ral 7035, light grey Ral 7016, anthracite grey Ral 3000, red, fire Ral 5003, sapphire blue (Other colors on request!) Main and cross beams galvani ...

Bearing platform 12,000 x 5,000 mm, load capacity 500 kg / m2 Dimensions / technical data: Dimensions steel construction: 12,000 x 5,000 mm Dimensions floor area: 12,000 x 5,000 mm Floor area: approx. 60 m2 Height OK floor ingesis: up to 3,500 mm (freely selectable) light height underside: OK minus 338 mm net load capacity: 500 kg / m2 same-distributed load Included in the scope of delivery are: 8 stand, one side 100 x 100 x 3 mm 6 main beam C+300 x 3 mm, L = 3,990 mm (perforated) 13 cross member S+300 x 2 mm, L = 4,800 mm (closed) 26 Mounting angle 3 Cross Associations 24 chipboard P6, 3000 x 850 x 38 mm, UK white, OK natural incl. fastening material incl. load signs Stand optionally in the following standard colours: Ral 7035 light grey Ral 7016 anthracite grey Ral 3000 fire red Ral 5003 sapphire blue (other colors on request) Main and cross bea ...

Bearing platform 16,000 x 5,000 mm, load capacity 500 kg / m2 Dimensions / technical data Dimensions steel construction: 16,000 x 5,000 mm Dimensions floor area max.: 16,000 x 5,000 mm Floor area: approx. 80 m2 Height OK floor ingesis: up to 3,500 mm (freely selectable) light height underside: OK minus 338 mm net load capacity: 500 kg / m2 same-distributed load Included in the scope of delivery are: 10 stand, one side 100 x 100 x 3 mm 8 main beam C+300 x 3 mm, L = 3,990 mm 18 cross member S+300 x 2 mm, L = 4,800 mm 36 Mounting angle 4 Cross Associations 33 chipboard P6, 3000 x 850 x 38 mm, UK white, OK natural incl. fastening material incl. load signs Stand optionally in the following standard colours: Ral 7035 light grey Ral 7016 anthracite grey Ral 3000, red, fire Ral 5003 sapphire blue (other colors on request) Main and cross beams galvanized  ...

FUJI PROOFGERAET PICTROSTAT 400 D Built in 2001 Manual is available. Inks and papers are also available The former Nettoneupreis DM 63.900,00 General Fujifilm Pictrostat 400 d With the 400 d Fujifilm Pictrostat, Fujifilm presents its digital full color copier for prints up to format DIN A3. By combining the functions of the High-performance digital printer Pictrography and the copying of his little brother Pictrostat 300 Pictrostat 400 d was launched very successfully in the German market. As also the Pictrography, Pictrostat 400 d with the Thermoentwicklungs-works and -transfer process, which completely without chemicals comes out and basically like a Image separation works. Only water, light, heat, pressure, become the processing Need photo paper and the donor paper developed by Fujifilm. This eco-friendly Method to produce prints in photo quality has ...

Saw blade grinding machine Schmidt Tempo ECE 45 2019 technically overhauled CBN deep-cut process For regrinding and for the production of circular saw blades with angular and arched tooth according to tooth shape A, AW, B, BW, and C according to DIN 1840 for circular saw blades from 20 mm to 550 mm. â?¢ Clock and grinding time display â?¢ automatic, motorized central lubrication â?¢ Centering holder with centering bolts 16 mm . . . . . . . . . . . . . . . . . . â?¢ Clamping nut with mech. Clamping force reinforcement â?¢ Saw blade holder â?¢ Preparation for grinding with oil â?¢ Centering rings as needed â?¢ LED machine light â?¢ Program for round grinding â?¢ Reporting light â?¢ Tool set

PTC CTR-C cold water trailer similar but no dynajet, oertzen, falch, ROM, Rioned, plaid, ... - Single-axis attachment on hot-dip galvanized frame with stub-foot with wheel, parking brake, automatic return gear, stand-up, back lights and reflectors, zugoese for 50 mm clutch, 13" tyres and ABS. The following cold water models are available: CTR-C 43/180 | 43l/min. at 180bar | Petrol Engine: Honda GX690 17.7kW CTR-C 55/160 | 55l/min. at 160bar | Petrol Engine: Honda GX690 17.7kW CTR-C 60/150 | 60l/min. at 150bar | Diesel Engine: Kohler KDW 1003 19kW CTR-C 20/350 | 20l/min. at 350bar | Diesel Engine: Kohler KDW 1003 19kW - Dimensions: 3,045 x 1,390 x 1,190 - Empty weight: approx. 350 kg - High pressure pump: Comet TW Premium with integrated gearbox - HD reel: manually with max. 1/2" hose (included) - Water supply reel: manually with 35 m. 3/4" hose - Water tank: 400 l - Op ...

PTC JTR-C Cold Water Trailer similar but no Dynajet, Oertzen, Falch, ROM, Rioned, Karo, ... Bhdwvn8yff - Single-axis attachment on hot-dip galvanized frame with stub-foot with wheel, parking brake, automatic return gear, stand-up, back lights and reflectors, zugoese for 50 mm clutch, 13" tyres and ABS. The following cold water models are available: JTR-C 60/200 | 60l/min. at 200bar | Engine: Kohler KDW 1404 26kW JTR-C 75/150 | 75l/min. at 150bar | Engine: Kohler KDW 1404 26kW JTR-C 75/210 | 75l/min. at 210bar | Engine: Kohler KDW 2204 37.5kW JTR-C 84/190 | 84l/min. at 190bar | Engine: Kohler KDW 2204 37.5kW JTR-C 102/150 | 102l/min. at 150bar | Engine: Kohler KDW 2204 37.5kW Engine type: TIER III (Kohler) or Stage V (Yanmar) - Dimensions: 3,370 x 1,640 x 1,540 - Empty weight: approx. 600 kg - High pressure pump: HPP - HD reel: fixed and manual or hydraulic with max. 1/ ...

The SUPERBOX is a box butterfly that feeds, opens, folds, shapes the boxes and seals their lower part with adhesive tape. Its great versatility also lies in the possibility of using commercially available adhesive tape rolls. The machine consists of a cardboard magazine, an area where the cartons are opened and an output roller conveyor, on which the bottoms of the folding cartons are provided with adhesive tape. The format change is conveniently controlled via 5 handwheels, which is followed by an adjustment of the passport stamps of the cardboard magazine and the position of the suction cups. specifications Product dimensions: Length: 570 mm Width: 410 mm Height: 500 mm Min. product dimensions: Length: 250 mm Width: 170 mm Height: 90 mm Cardboard magazine for standard machine: 50/60 Operating voltage: 400V 3Ph+T 50Hz (others on request) Power consumption: 1 kW  ...

Part No.: EO2-XR-ULZW // S. No.: 1 045042 Equipment / Additional information Technical specifications: Spectral technology: Spectral range: 380-730 nm Physical measuring interval: 3.5 nm Optical resolution: 10 nm Spectral resolution: 380 nm… 730 nm with 10 nm interval Measurement frequency in scan mode: 200 measurements / sec. Reflection measurement: spectral reflection (dimensionless) Emission measurement: spectral radiance (Mw / nm / m2 / sr), luminance (cd / m2) Ambient light measurement: spectral irradiance (mW / nm / m2), luminance (lux) measuring head for diffuse light with cosine correction

Mini roller cutter Our range now also includes machines for processing residual rolls, for example from paper production, the packaging industry, printing houses, textiles, aluminium rolls, film rolls, etc. These heavy rollers cannot be processed efficiently and safely with the normal cutting systems, but with these special "guillotine" roller cutters this is no longer a problem. The mini roller cutter can be seen here as a standard version. We offer the Mini roller cutter in version G20 / 25 and G30. All data can be customized according to the customer's wishes. (Sensors | Protective grille | Light barriers | colour, etc.) Roll width: max. 700 mm Roller height: max. 800 mm Drive: 5.5 Kw Cutting force: 25 T cylinders Weight: 1200 kg Working cycle: 65 seconds Including automatic return: Important roll cutting width and roll cutting height can be adjusted as desired. Dep ...

1 Wulf steam boiler system Manufacture No. 3813 Year of construction 1993 Power: 8 to Damph per hour Up to 13 bar vapour pressure with laterally mounted steam pipe register with Weißhaupt Combi burner for gas and light oil with lying boiler feed water tank Capacity 8,000 l with all-round piping and Structural steelwork with steel fireplace with exhaust gas heat recovery register system with Wulf Elektro control cabinet 1 Wulf steam boiler system Manufacturing No. 3813 Year of construction 1993 Output: 8 to steam per hour Up to 13 bar steam pressure with laterally attached steam pipe register with Weißhaupt Combi burner for gas and light oil with horizontal boiler feed water tank Contents 8,000 l with all-round piping and steel construction with steel chimney with exhaust heat recovery register system with Wulf electrical control cabinet

Spectrallight Gretag Macbeth Spectralight III uses a patented filtered tungsten halogen daylight source. This means that it contains an even balance of color energy, just like natural daylight. The more even the balance of color energy, the more accurate the light source makes color. This color energy is displayed in a spectral power distribution curve (SPD). If your light source doesn't match the SPD curve for natural daylight, your ability to evaluate color is distorted. That means you could approve color that your customers reject and vice versa! Manufacturer: Gretag Macbeth Type: SPL III Further data: see also photos All information without guarantee

Hydraulic panel shears - storage machine - incl. foot switch, touch screen, rear installation room with light barrier monitoring, automatic/electric cutting gap, automatic/electric cutting angle, hydraulic hold-down, mot. Backgauge up to 1000 mm depth -Illustrations similar- Hydraulic plate shear - storage machine - incl. foot switch, touchscreen, rear set-up area with light barrier monitoring, automatic/electrical cutting gap, automatic/electrical cutting angle, hydraulic hold-down, mot. backgauge up to 1000 mm -images similar-

ZOLLER SMILE / PILOT 3.0 presetting and measuring machine was manufactured in 2019 in Germany. The machine is a professional tool measuring and presetting device, whose easy operation and precision guarantee flawless results. A telecentric lens and a CCD camera with integrated LED ring for measurements in reflected light (blade inspection) are used to perform the measurements. ZOLLER SMILE 420 is equipped with the CNC controller ZOLLER »pilot 3.0« and functions such as automatic blade recognition, measurement of radial run-out and axial run-out, maximum contour function and cutting edge control. The tool to be measured can have a maximum length of 420 mm and a maximum diameter of 420 mm. Specifications of the ZOLLER SMILE / PILOT 3.0 presetting and measuring machine - maximum tool length Z: 420 mm - maximum tool diameter D: 420 mm - diameter measurement according to Abbe’s p ...

BOSCHERT G CUT 2504 CNC guillotine shears were manufactured in 2014 in Germany. The guillotine is designed for cutting metal sheets with a maximum length of 2600 mm and a thickness of 4 mm (mild steel st42) or 2 mm (stainless steel). The sheet metal is held in place by 13 hydraulic clamps and, thanks to the installed CNC controller with touch panel, it is also possible to store many different work programmes, making the machine very useful and versatile. After entering the parameters of the steel sheet to be cut, the controller automatically sets the cutting gap, choices the angle of the upper knife and the appropriate pressure force and then starts the cutting process. The guillotine is also equipped with, among other things: a foot control to facilitate the operator’s work, light curtains to prevent a worker from entering the working area of the machine and an automatic metal shee ...

table length: 1200 mm table width: 800 mm table height: 850 mm Vertikal stroke: 50 mm weight of the machine ca.: 0,25 t dimensions: 1,2 x 0,8 x 0,85 m Special offer ! Siegmund Workstation incl. 2 drawers + tool set B Perforated plate: Premium Light. Through hardened tool steel X8.7, plasma nitrided and BAR-coated, bore Ø 28 mm. Drilling surface 100x100 mm grid, material thickness approx. 15 mm. Consisting of: 1x 004002 (Siegmund Workstation) 1x 804004.X7 (perforated plate) 1x 284030 (clamp holder) 1x 004020 (shelf) 1x 284035 (bolt and prism holder) 1x 004025 (tool wall including shelf) 2x 004210 (drawer) 4x 280610.N (clamp) 8x 280511 (double quick release bolts without groove) 1x 800653.N (spacer ring for Premium Light 4-pack) 6x 280412 (stop) 2x 280109.N (angle) 1x 280852.1 (Allen key) 1x 004303 (vice) The data for this ad was created with ModulMWS - the software solution of LogoTech ...

Hach DR 3800 VIS Spectrophotometer The DR 3800 is a VIS spectrophotometer with a wavelength range of 320 to 1100 nm. The device comes with a complete set of application programs and supports multiple languages. The DR 3800 spectrophotometer contains the following Programs and operating modes: Saved programs (pre-installed tests), barcode programs, user programs, favorites, single wavelength, multi-wavelength, wavelength scan and time scan. The DR 3800 spectrophotometer performs digital measurements in concentration, absorbance or % transmission. When selecting a user-generated or programmed method, a structured menu control and prompts guide the user through the test. This menu system can also generate reports, statistical evaluations of generated calibration curves and reports on instrument diagnostic checks Display mode: transmission (%), absorbance, and concentration Light ...

XMET8000 handheld spectrometer for quick and easy elemental analysis and many other possibilities. The X-MET8000 handheld XRF instruments offer high performance for reliable testing of materials and chemical compositions: fast, precise analysis for fast sorting (metals, polymers, wood, solutions, soil, ores, minerals, etc.). The X-MET is practical, robust and easy to use, for results you can rely on. The X-MET is perfect for the analysis of light elements (Mg, Al, Si, P, S, Cl). It offers the lowest detection thresholds with laboratory-quality results in seconds, day after day. Test a wide range of materials with the versatile fundamental parameter (FP) method and empirical calibrations (traceable to certified reference materials) where the highest precision and accuracy is required. Friendly The intuitive, icon-based user interface requires minimal operator instruction.  ...

ERMAK HAP 2600 X 80 CNC hydraulic press brake was manufactured in 2005 by the Turkish company ERMAKSAN MAKINA SANAYI TIC. LTD. ŞTI. The machine characterised by high performance and robustness, performs precision bending of workpieces with a maximum length of 2600 mm and a thickness of 6 mm with a force of 80 tonnes. The machining parameters in the X and R axes are programmed easily and conveniently through the CYBELEC DNC 60 CNC controller located on a mobile arm. The HAP 2600-80 press brake also offers a high level of operator safety, thanks to an emergency button and light curtains made by FIESSLER ELEKTRONIK to prevent unauthorised entry into the machine’s working area. The total weight of the press brake is 5600 kg. Technical specifications of the ERMAK HAP 2600 X 80 CNC press brake - press force: 80 t (800 kN) - feed in X/R axis: 500/160 mm - maximum sheet metal length: ...

ERSA HOTFLOW - 7 Soldering furnace / tunnel dryer / belt dryer / continuous dryer Type: HOTFLOW – 7 Convection oven as soldering oven / tunnel dryer / belt dryer / continuous dryer for drying sheet materials on top and bottom. 4 heating zones at the top, 4 heating zones at the bottom, for drying on both sides. Rolling bars at a distance of approx. 4.5 cm on 2 transport chains as a support for plates Temperature range from 20° to 300°C Rated power Pn = 72 KW Nominal current In = 106 A Voltage: 3 x 400 / 230V Back-up fuse: 3 x 125 A Frequency 50 Hz Power: 67 KW Year of construction: 2000 Dimensions: Length: 5250 mm Width: 1300 mm Height: 1750 mm (incl. warning light) Height: 1450 mm (without warning light) Dry section: Length of heating zones: 3300 mm Transport width: 500 mm Exhaust pipes and additional fan can be supplied. Circuit diagrams are ...

ERFURT PKZZ 315 double column press manufactured in 1984 in Germany is used for, among others, cutting, machining, bending and punching sheet metal and strip metal. Features such as the ability of extensive workpiece machining, a large work table and a 315-tonne operating slider make the crank press ideal for mass production of things such as washing machine parts, agricultural machinery or other types of vehicles. The ERFURT mechanical press is also distinguished by its high-quality welded steel construction, ensuring excellent stability during the production process. The machine uses a slider with a beam ejector, which is adjustable within a range of 400 mm via a motor reduction gear with overload protection. In order to increase the life of the tools and the quality of the parts produced, the 2500 mm long and 1400 mm wide work table has been equipped with hydropneumatic cushions.  ...

Key data: 135 t, 3150 mm

HACO ERMS 36-135 CNC press brake was built in Belgium in 2006. The machine, with its robust construction and high press force of 135 tons, is ideal for even the most demanding machining of workpieces with a length of 3600 mm. To ensure a high level of safety and ease of use, the ERMS 135T CNC press is equipped with the intuitive HACO ATS 560 control and light curtains which prevent unwanted entry of the operator into the working area. The total weight of the press is approximately 88000 kg. Technical data of the HACO ERMS 36-135 press brake - maximum press force: 135 t - maximum sheet metal length: 3600 mm - controller: HACO ATS 560 - bending speed: 10 mm/s - approach speed: 100 mm/s - return speed: 80 mm/s - slider stroke: 200 mm - reaction time: 75 ms - distance between body walls: 3150 mm - safety distance: 300 mm - light curtains - foot control - motor power: 15 kW - ...

DIRECTLY FROM THE PRINT SHOP We sell this machine on behalf of our customer and try to realize his asking price. However, we are open to offers from you. Offer consisting of: EBA Cutting Machine 551 LT with side tables and light barriers Electro-mechanical knife drive Air table Chpjpskqes Hydraulic drive for press beams Infinitely variable pressing pressure (min. 200 daN, max. 1100 daN) with display via pressure gauge Foot pedal for pre-pressing or as a cutting indicator Press beam cover Electrically operated backgauge with professional program control electronic handwheel with infinitely variable speed for manual backgauge fine adjustment Optical cutting indicator with bright light-emitting diodes (LEDs) Press beam guided on both sides for uniform pressing pressure Djqedv Precision backgauge spindle adjustable backgauge rake with narrow pitch (32 mm) and plast ...

FINN POWER E-BRAKE 65-2550 HS TS 3 servo electric press brake built in 2007 in cooperation with SAFAN (now SafanDarley), achieves the highest quality of workpiece machining while maintaining low operating costs. The high press force of 65 tonnes, 6 numerically controlled axes (X, Y1, Y2, R, Z1, Z2), electric drive and low energy consumption make the machine the best choice among other press brakes available on the market. One of the machine’s greatest advantages is its electric drive, which eliminates the occurrence of the so-called deflection arrow effect and its compensation through even force distribution on the slider. Additionally, in order to increase the working speed and reduce noise, the FINN POWER press brake only consumes electricity when the slider is going down. The entire working area is protected by a programmable light curtain that, when interrupted by hand, allows f ...

Optic sensor, light sensor, light barrier -Type: OG5029/OGT-HPKG -Price: per piece -Number: 11x available -Weight: 0.1 kg

Optic sensor, light sensor, light barrier -DC 24 V 10 W. -RW: max. 5 m -Price: per piece -Number: 3x available -Weight: 3.5 kg

CNC Wood Milling Machine 6KW 1300x2500 CNC milling machine 1325 INDUSTRY 2.0 6KW 1300x2500 ◼Invest in the quality of the INDUSTRY 2.0 Series The INDUSTRY 2.0 series differs from the standard series by using the best and most precise motors in its class and the power transmission, which significantly increase the machining capabilities of the machine, making it the most industrialized series in this price range. ◼The INDUSTRY 2.0 series CNC milling plotter with a working surface of 1300x2500mm and a clearance in the Z axis of 300mm is equipped with an electrospindle with a power of 6kW and 24000 rpm. on a ceramic bearing. The working table of the machine is made in hybrid technology - it has vacuum sections and subsections for automatic, non-invasive clamping of the processed material, as well as T-Groove slots for manual clamping. ◾Hybrid table, i.e. vacuum, enabling non ...

TechnologieCNC Milling Plotter CNC 1530 INDUSTRY 2.0 ◼Invest in the quality of the INDUSTRY 2.0 Series The INDUSTRY 2.0 series differs from the standard series by using the best and most precise motors in its class and the power transmission, which significantly increase the machining capabilities of the machine, making it the most industrialized series in this price range. ◼The INDUSTRY 2.0 series CNC milling plotter with a working surface of 1500x3000mm and a clearance in the Z axis equal to 300mm is equipped with an electrospindle with a power of 6kW and 24000 rpm. on a ceramic bearing. The working table of the machine is made in hybrid technology - it has vacuum sections and subsections for automatic, non-invasive clamping of the processed material, as well as T-Groove slots for manual clamping. Covscsx ◾Hybrid table, i.e. vacuum, enabling non-invasive fixation of th ...

CNC milling machine 2100x4000mm 9kW HEAVY DUTY TechnologieCNC CNC Industry 2.0 2140 ATC The INDUSTRY 2.0 ATC series differs from the standard series by using the best and most precise motors in its class and the power transmission, which significantly increase the machine's machining capabilities, making it the most industrialized series in this price range. ✔The INDUSTRY 2.0 ATC series CNC milling machine with a working surface of 2100x4000mm and a clearance in the Z axis equal to 300mm is equipped with an electrospindle with a power of 9kW and 24000 rpm. on a ceramic bearing. The working table of the machine is made in hybrid technology - it has vacuum sections and subsections for automatic, non-invasive clamping of the processed material, as well as t-groove slots for manual clamping of irregular shapes. ✔ATC - The machine is equipped with an automatic linear magazine wi ...

MAN TGX 26.480 6x2 Mileage: 712545km Engine/Assistance Systems -D2676LF45 - 480 hp / 353 KW EURO6 SCR-2300Nm(2500 with TopTorque) C-R New -Electronic speed limiter 89 km/h + 1km/h Cruise Control Tolerance -Low noise certificate for Austria and L- sign • COP document • Exhaust gas confirmation Euronorm • CEMT certificate • National approval documentation Germany noise measure 80 dB (92/97EEC) -Fuel filter -Start-up aid -HA Air -HA differential lock -Fuel tank aluminium 800l right and 60l AdBlue • Fuel tank attachment • Lockable tank cap • 1 pc. ventilated for Simultaneous locking - AdBlue tank cap lockable 1 piece -MAN BrakeMatic (electronic braking system) -Emergency Brake Assist 2 (EBA2) -Anti-lock braking system (ABS) -Traction Control (ASR) -Electronic Stability Program (ESP) -Gearshift MAN ComfortShift -Transmission ZF 16 S 23 ...

Scanware Blister Control System: - Screen EM TFT 15" - Camera system DOM-323/SU/4C (with 3x camera JAI CV-M71CL) - Product recognition system LYNX-Spectra - Multiplexer MUX-3 3xCL - White light LED lighting LEDW-Po3/S5 - Lighting attachment ES-323 - Light panel KAN-303 - Network and I/O module S02

Battenfeld HM 240 1330 2011 Battenfeld TM 400 2250 2009 We have 2 thermoset injection machine to sell. Battenfeld BCT 1800-1000 year 1994 (with Robot) Battenfeld BCT 1800-1000 year 1993 TM 27001900 BA 600200 CDC TM35001330 BA 1000 BKT THERMOSET INJECTON MACHINES Thermoset Inj. Machine- I Thermoset Inj. Machine- II With Battenfeld Robot BATTENFELD BCT 1800/100 BATTENFELD BCT 1800/100 Construction Year 1993 1994 Screw Diameter Ø60 mm Ø55 mm Clearance between tie bars 515 x 515mm 515 x 515mm Day light 1.000mm 1.000mm Working Hours 81814 h 57929 h Also: Name Battenfeld Battenfeld Type of machine HM-E 240/ 1330 INSIDER TM-E 400/2250 Control system Unilog B6E Unilog B6 Year of manufacture 2011 2009 operation hours 17 254 11 288 Cla ...

Frequency converter, frequency converter, drive converter, controller, variable speed drive ACS800-04-0205-3 160kW 380-415V Input Voltage (Uin):380 ... 415 V Mounting Type:Module for cabinet assembly Output Current, Heavy-Duty Use:234 A Output Current, Light-Overload Use:285 A Output Current, Normal Use:290 A Output Power, Heavy-Duty Use:132 kW Output Power, Light-Overload Use:160 kW Output Power, Normal Use:160 kW

SUTEAU ANVER XPM 18X13 300T receding head die cutting press was built in France in 2008. The machine aimed at mass production, is used in the process of precise cutting in foam and non-metallic materials, such as plastics, textiles and rubber. Built-in hydraulic systems combined with a stable design and reliable components ensure high precision and speed of cutting, regardless of machined material. The material taken from rolls or sheets is pressed against the machine head by the vertical movement of the working table, under which hydraulic cylinders are located. The cylinders exert a balanced pressure to achieve the ideal position of the table in relation to the head. The material is then machined using dies that can be mounted either to the head surface or on a lifted table. To facilitate the operator’s die positioning and the insertion and removal of the cut material, the SUTE ...

Technical details Pressure 110 t Technology Passage width 1200 x 1000 mm Stroke 1200 mm Machine weight approx. 12 t Space requirement approx. 4500 x 4300 x 2700 mm Master cylinder 1 piece Installation height (distance table to plunger plate) 1200 mm Table height 700 mm Table can be extended by 1200 mm Table tiltable by 45 degrees Upper tool folds down by 180 degrees Table rotatable by 180 degrees Table load max. 10 t Travel speed of the table 25 mm/sec Flow speed 195 mm/sec Return speed 130 mm/sec Working speed adjustable from 0 to 10 mm/sec. Table area between the columns 1250 x 1000 mm Engines WEG Accessories Paint structure RAL 7035 (light grey) Additional information Painting cladding, doors, maintenance balcony RAL 1021 (Yellow) Painting accessories RAL 7021 (dark grey) Columns and cylinders are made of tool steel SAE 1045 (identical to German standard C4 ...

cutting range for steel to: 25,0 Trennschnitt mm cutting range for steel to: 20,0 Qualitätsschnitt mm capacity at 100%: 25,0 Ampere cutting medium: Druckluft output: von 20 - 40 Ampere output: Eingang 4,9 KW voltage: 230 V range L-W-H: 505 x 147 x 305 mm weight: 8,0 kg Cuts carbon steel, stainless steel, aluminum, copper and more... The AVALON 40.1 PFC is a light, handy plasma cutting system with high Cutting performance and top cutting quality. Their light weight and ease of use Handling makes them the ideal candidate for trade, workshop and industry. Properties: - IGBT technology - Active PFC technology for high duty cycle and energy efficiency - Manual switch to activate airflow - to set the test air pressure without having to trigger the burner. - Lightweight and compact - Intelligent protection function protects the plasma torch from damage - such as incorrect air pressure, missing ...