136,145 used machines on RESALE, but how to find them? Machine Search
Metal Detector Loma Systems EMC90541-14363 -Metal detector -Manufacturer: Loma Systems -Weight 185cm -Inlet tunnel: 35cm wide and 11.5cm high -380 Volt 3OPh 50Hz
1 PIMATEX high temperature sample dyeing machine type Draw-Lab 140/5, year 1994, capacity 5 Kg, machine equipped with filter and addition vat, SETEX 505 dye cycle controller, circulation pump controlled per SIEMENS inverter, machine delivered fully erected because electrical panel and pneumatics don't need to be disconnected
used
Inv. Num. : 5698 Type: LKT 250 Producer: METALPRESS Created: 1974, GO 2002 Parameters: Compressive force: 250 t Table length: 1150 mm Top table width: 1580 mm Maximum stroke rate top table: 7-25 1/min Ram stroke: 250 mm Adjusting the plunger: 100 mm Machine weight: 22950 kg GO 2002: converted to hydraulic clutch electronic control
Wärtsilä Lipstronic thruster control system overhauled. W006927795 Lipstronic 793.083.001.0001 Printcard Thruster Control System
Laska W 130 Automatenwolf Perforated disc 130 mm Filling quantity approx. 1 to 2 E 2 boxes Drive 7.5KW 400 Volt 50Hz
Hello, We hereby offer you a used articulated telescopic work platform on wheels (telescopic aerial platform) from the manufacturer TEREX AERIALS, type TA30N Boom Lift. The following technical data have been taken from the manufacturer's operating instructions and brochures, for which we cannot assume any liability for accuracy and completeness. Manufacturer: TEREX AERIALS Type TA30N Boom Lift Built in 1999 Operating hours 887 hours Transport dimensions retracted 4.20 x 1.22 x 2.12 m (L x W x H) Curb weight 4800 kg Max. height of the floor of the working cage 9.14 m Max. working height 11.14 m Max. working width 5.20 m Outer turning circle 3.50 m Max. climbing ability 20 % Max. travel speed, boom retracted 4 Km/h Max. travel speed, boom extended 0.75 Km/h Safe load capacity (2 persons) 225 kg Max. noise level 70 dbs at 3m Operating Temperature Range -5°C to 40 ...
We sell a Lippelt Mini Rustica with guillotine and punch. Good bakery condition
Used rack oven HEIN, Type: Luxrotor LR 86 -In bakery condition- - for 1 rack trolley 60 x 80 cm - Gas or oil burner - technically tested, immediately ready for use - an overhaul is also possible - Further information on request The furnace is technically tested and immediately ready for use. Viewing and test run are possible by arrangement.
Used spiral conveyor belt with downward direction LIPSIA -In bakery condition- - Spiral conveyor belt - Collection table - Crimp barrel catch plate The plant is out of service. Viewing and test run are possible by arrangement.
Double-acting hydraulic cylinder, CK-80/56x0800-L004-H-B1X, Atos, new Special price If you have a VAT number, we will be happy to issue you with an invoice without VAT. New! - never been used and is completely new, - comes from a spare parts warehouse of a certified production facility, Technical information: - Double-acting hydraulic cylinder with swivel eye - Specially manufactured for Frech/Weingarten die casting machines - Suitable for GDK 2000 to GDK 4100 machines - Frech item number 949390 - Piston diameter 80 mm, piston rod diameter 56 mm - Max. stroke 800 mm, piston rod thread M27 x 2 - Centre of swivel eye to retracted piston rod face 510 mm - Swivel eye d40 mm 6 months warranty We give you 6 months warranty for these goods from the date of invoice. In case of any defect, which is not the fault of the buyer, the goods can be returned. We will refund th ...
Double head saw EMMEGI NORMA 400 TU/4 Screwing unit GEVO SE1-SA Double head welding machine URBAN AKS 1200 Single head welding machine PRESSTA EISELE APOLLO End milling machine HAFFNER AF 362 Drain slot milling machine ROTOX FWS 380 Copy router STB F130/S Corner cleaning machine STB WP-OF2 Glazing bead saw HAFFNER GL 172
Plate max width 650 mm Plate min length 460 mm Weight 150 kg Current 220V 7.5 Amp, 1.5 kW Working Dims W107 x D180 x H106cm Packaging Dims W107 x D100 x H106cm
Qty. 1 Second-hand 4-Hi Non-Reversing Rolling Mill – still in operation! Mfc.: Lheung-Maschinery, Yushin Heavy Electric, Mitsubishi Built: Not specified! Rebuilt: 2017.08 Material: Aluminum & Aluminum Alloy Line speed: 80 m/min. Strip width: 550 mm Thickness: 0.3 – 6.3 mm Coil size: ID 508 mm OD 1500 mm Weight:
ABB Robotics Robot Parts number electric motors : PS 60/4-50-P-LSS-3612 PS 60/4-50-P-LSS-3613 The spare part is in good condition nevertheless, this is a used items, which has slight signs of wear, or may have.
Miwe fully automatic proofing machine Type: GVA 22LDS Year of construction 2015 for 4x 60x80cm racks or 8x 60x40cm freezer trolley Stainless steel cladding inside and out Total 10kW Coolant: R744 with floor with drive-up car with stainless steel ram protection inside 400/230V 3/N/PE 50Hz Touch control with compressor / fan on top The GVA was connected to a large composite system! Dimensions outside: Height: 265cm, Width: 180cm, Depth: 205cm Internal dimensions: 140x180cm W/D
Frame press Hess hydraulic Type: HYDRO-LUX Crimping dimension approx. L 3550 m x W 2250 mm Connected load 380 V / 50 Hz 2.6kw Hydraulic Pump Machine dimensions Length 6600 mm x Width 1600 mm x Height 2770 mm 0 - 8 bar pneumatic Optoelectronic measurement query. The window scantlings are placed in the feed channel so that the photoelectric sensor can measure whether the pressure beams and press corners need to be opened or closed. If the light beam of the probe hits the window scantlings, the machine receives the command to drive up in width and height until the working dimension is reached. Workflow: Automatic dimensional adjustment loose insertion Automatic pressing process loose presentation remove Automatic dimensional adjustment Program selection options in the control system: 1. Automatic measurement adjustment via optoelectronic measurement query with a ...
Main pump on the motor Hydromatics Nameplate 5005 348 80SP 1 R 101 P 1 227 . 22 . 20 . 39 1 708 698 11/83 2300 69.1 Goods in very good condition ! comes from: LIEBHERR crawler excavators Type. R 922 LC Fabr. No. 152 / 375 1982 Engine power: Deutz 78kw
Equipment Manufacturer Power Speed Generator BRUSH 3125 kVA 1500 rpm Gearbox Allen Gears 3860 kW 1500 rpm 1Generator Manufacturer: BRUSH Electrical Machines Limited Main SpecificationsParameter Value Parameter Value Type AC Generator Rated Output 3125 kVA Speed 1500 RPM Voltage 10,000 V Current 180 A Frequency 50 Hz Phase 3 Phase Brushless Excitement 2. Gearbox Manufacturer: Allen Gears Limited Location: Pershore, England Type Epicyclic / Planetary Gearbox Technical Specifications Parameter Value Model APG 23 Serial No. X5/40848 Year 1980 Type Planetary Gear Gear Ratio 9.473 Performance Parameter Value Rated Power 3860 kW Duty Power 3355 kW input Speed 14,210 RPM Output Speed 1500 RPM CT INDUSTRY 2 Rue laennec Rosny sous bois 93110 GSM 06 03 86 59 55
Loma Combination IQ3 metal detector and CW3 check weigher 250 x 90mm aperture. 200mm conveyor width. 360mm weigh pad width. 2100mm machine length. 920mm line height with adjustable feet. M&S Spec machine.
MHME twin lane decorer / florette machine - used for broccoli In good working condition
range L-W-H: 538 x 475 x 300 mm internal dimension: 450 x 448 x 300 mm material: verzinkt as good as new with some storage marks The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
In 2020, the machine was extensively overhauled for 7000 €. Proof available. Processes: - Chamfering 60° - Longitudinal turning up to a maximum of 40 mm - Centering drilling Workflow fully automatic: - Tensioning, feeding to - Rapid traverse forward - Work feed - Dwell time for cutting - Rapid traverse back - Relax, feed on Specifications: workpiece diameter approx. 80 mm workpiece diameter 6kt-SW 70 mm min. workpiece diameter round and 6kt 10 mm min. workpiece length 450 mm Speed range infinitely variable Level I/Stage II = 51-306/102-612 Electrical equipment 220/380 V, 50 Hz Motor power main motor kW 1.3/1.8 Engine power Coolant motor kW 0.07 Required air pressure 6-8 bar Weight approx. 520 kg Dimensions: L 1520 mm x W 610 mm x H 1350 mm Roller conveyor
Double Z Kneader / Sigma Kneader / Shovel Kneader / Trough Kneader Linden - Make HermannLinden, built in 1965 - Machine type K II 60, factory no. 605 - Refurbished in 2025, electrical equipment completely new - Frequency-controlled electric motor 4.0 KW - Frequency converter Optidrive E3 IP66 Outdoor with main switch, potentiometer and reversal of the direction of rotation - Control box with main switch, emergency stop and undervoltage tripping - Speed from approx. 20 to 200 rpm. - Belt drive - 2 Z-waves - All parts in contact with the product in copper and stainless steel - Single-walled copper container approx. 600 x 600 x 450 mm = approx. 150 litres - Emptying by manual tilting by means of a handwheel - Weight approx. 1200 kg - Overall dimensions approx. 1400 x 1500 x 1700 mm - Very stable design. Lubricated with H1 food fat.
Inv. Num. : 9002 Type: LB3000EXII MYW800 Producer: OKUMA Created: 2014 Parameters: Control system: OKUMA OSP-P300L CNC Switch-on hours: 65458 h Hours: 36054 h Maximum turning length: 785 mm Max. turning diameter: 480 mm Max. turning diameter: 340 mm Spindle diameter: 80 mm Motor power: 22 kW Minimum spindle speed: 45 1/min Maximum spindle speed: 5000 1/min Travel X: 260 mm Travel Y: 115 mm Travel Z: 510 mm Tool magazine: 12 pieces Length: 3330 mm Width: 1800 mm Height: 2250 mm Weight: 5250 kg Equipment: Baking Collets Axis C Sub-spindle Powered tools OSP-P300L Advanced One Touch CF-M-E FILTERMIST FX4002 Suction High-pressure cooling Grips Tool Holder Reducer insert tube In June 2019, the spindle was repaired due to defective bearings. In June 2025, the U4 control unit was replaced. In October 2025, the M control unit w ...
Leutenegger (Starrag) washing box Specifications Year of construction: 2000 Bathroom capacity: approx. 0.9 m3 Chemistry: Henkel P 3 Voltage: 3x400V/230V 50 Hz Supply line: 40 A Control voltage: 24 V DC Temperature max: 50° C Electric heating Heating capacity: 3x3.25 kW = 9.75 kW Working pump: 3 kW Exhaust fan: 0.37 kW Exhaust air volume: 400 m3/h Shipping costs on request
Machine type TIG inverter welding system gas-cooled DC and AC system Merkle brand Type LiteTIG 190 AC/DC Connection voltage 1 x 230 Volt Setting range 5 – 190 amps Duty cycle 25 % ED at 190 Ampere 60% ED at 140 amps 100% ED at 115 amps Current adjustment infinitely variable weldable material thickness 5 mm Cooling inverter by built-in fan Cooling burner gas-cooled Version portable mounting system Fuse 16 amps Dimensions L x W x H 410 x 150 x 240 mm Weight 7.4 kg Age 6 months Condition workshop tested, as new, incl. UVV test protocol Scope of delivery welding system with the following accessories: 1 piece TIG burner 4 mtr. long 1 piece ground cable 1 piece pressure reducer with 2 pressure gauges 1 pair of TIG gloves 1 piece spare parts box kpl. Equipped 24 months warranty 1 piece instruction manual List factory price ex ...
350 x 200mm aperture. 300m conveyor width. 1.8m long. Push reject system. Right to left production. Full supermarket spec. 880 Line height with adjustable feet.
300mm Conveyor Width. 350mm Weighpad Width. 870mm Line Height. 1370mm Machine length. Right to left production line. Reject bin. Supermarket specification. Adjustable feet.
Double Z Kneader / Sigma Kneader / Shovel Kneader / Trough Kneader Linden Suitable for highly viscous, tough, plastic or sticky materials such as adhesives, sealants or pastes. Thanks to their two interlocking Z-shaped kneading arms, they can process substances that are hardly homogenizable with normal mixers. - Make HermannLinden, built in 1965 - Machine type K II 60, factory no. 605 - Refurbished in 2025, electrical equipment completely new - Frequency-controlled electric motor 4.0 KW - Frequency converter Optidrive E3 IP66 Outdoor with main switch, potentiometer and reversal of the direction of rotation - Control box with main switch, emergency stop and undervoltage tripping - Speed from approx. 15 to 60 rpm. - Belt drive - 2 Z-waves - All parts in contact with the product in copper and stainless steel - Single-walled copper container approx. 600 x 600 x 450 mm = appr ...
550 x 160mm aperture. 400mm conveyor width. 3250mm machine length. 900mm line height with adjustable feet. New belt fitted on the machine. Right to left production. Full supermarket spec.
450 x 160mm aperture. 300mm conveyor width. 1800mm machine length. 870mm line height. Left to right production.
350 x 115mm aperture. 300mm conveyor width. 1.3m machine length. Air reject system. 1.3m machine length. Adjustable line height with wheels.
370 x 100mm aperture. 300mm conveyor width. Right to left production. Reject system. M&S Spec. 2100mm long 840mm line height with adjustable feet.
Usable aperture size 350mm (wide) x 135mm (high) 230mm wide conveyor belt Full length 2500mm Line height 850mm Auto push reject on both machines. Left to right production direction
350 X 110mm usable aperture. 260mm conveyor width. 920mm line height. Twin head metal detector with reject. M&S Spec. Right to left production line.
Usable aperture size 550mm (wide) x 200mm (high) 450mm wide conveyor belt Full length 2000mm Line height 860mm Right to left production direction
450 x 130mm aperture size. 320mm wide conveyor belt. Checkweigher table width 390mm. Air blast reject system. 2200mm machine length. 900mm line height.
450 x 155mm aperture 400mm conveyor width. 920mm line height with adjustable feet. 1800mm machine length. Right to left production. Drop reject system.
maximum number of results exceeded
please refine your search
