km 250 b used for sale

plate width: 2500 mm sheet thickness - max.: 32 mm sheet thickness - max.: 39 mm sheet thickness - min.: 8 mm bale length: 2700 mm number of straightening: 7 Rollers number driven straightening rollers: 5 Stk straightening roll diameter: 290 mm diameter of input / output straightening rollers: 345 mm number of support rollers: 13 Stk diameter of support rollers: 288 mm stroke of upper beam: 120 mm straightening feed: 16 m/min rated power of main drive: 90 kW : 138 kw weight: 79 t - max. sheet thickness( St 50): 32 mm - max. sheet thickness( St 34): 39 mm - min. sheet thickness( St 50): 8 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 250 t throat: 400 mm stroke: 30...140 mm table-size: 1000 x 750 mm hole in the table: 360 x 400 mm ram surface: 630 x 500 mm ram adjustment: 110 mm total power requirement: 18 kW weight of the machine ca.: 16 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 250 mm roll length: 500 mm rolls drilled: peripher Nip adjustment: hydraulisch total power requirement: 2x 5,5 kW Condition: new rolling mill, with CE marking, with 2 year warranty Specification: Monobloc laboratory rolling mill 250 x 500 mm - new - roll diameter: 250 mm - Roll length: 500 mm - Roll bore: peripherally drilled - Single drives: variable friction ratio - Roller bearing: roller bearing with manual grease lubrication - Gap adjustment: hydraulic - new hydraulic unit for roller nip and emergency system - New rotary unions make Johnson-Fluiten - two adjustable guide plates to adjust the working range on the rollers. - Working range approx.: 100 to 460 mm - Roller gap, during the working phase 25 mm - tiltable guide plates made of nylon-polyethylene Material - Stainless steel tank - New saf ...

pressure: 250 t throat: 360 mm Table dimensions: 1250 x 630 mm table diameter: 250 mm dimension of ram: 850 x 450 mm dayligth: 800 mm piston stroke: bis 500 mm diameter of piston: 400/360 mm ram stroke speed: abwärts 200 mm/sec ram stroke speed: aufwärts 110 mm/sec total power requirement: 20,5 kW weight of the machine ca.: 8 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 600 mm y-travel: 400 mm z-travel: 500 mm total power requirement: 6 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I am selling this machine. Plugged in, can be tested. Very good condition. Documentation for the machine. Can be sent via whatsapp video of the machine

Lifting crane with trolley lifting capacity 0.25t

Manufacturer: Arburg Model: ALLROUNDER 630 S 2500 – 675 Year of Manufacture: 2003 Technical Specifications: - Operating Voltage: 400 V, 3-phase, 50 Hz - Control Voltage: - 230 V AC, 50 Hz - 24 V DC - Motor Heating Rated Current: 113.0 / 33.0 A - Total Rated Current: 146.0 A - Total Connected Load: 83.0 kW - Tie Bar Distance: 630 mm - Clamping Force: 2500 kN - Screw Diameter: 45 mm - Max. Part Weight (PS): 252 g - Core Pull: Yes (1 unit) - Orientation: Horizontal - Number of Components: 1 - Drive Type: Hydraulic - Robot Operating Hours: 110315 (automatic operation) Find more here - / Contact us at -

Used CIP system: 2 x 2500 litre stainless steel tanks For sale is a used CIP system with two 2,500-liter tanks. This clean-in-place system is the ideal solution for the automated and hygienic cleaning of your production systems in the food industry, beverage industry or even in the pharmaceutical sector. Two separate stainless steel tanks (2,500 litres each) Made of stainless steel (V2A)

Leather goods wrapping machine with various tools up to approx. A6

AL-KO POWER UNIT 250 P - Exhibition machine -Pre-separator integrated, automatic extinguishing system integrated---------- Technical data ----------Extraction nozzle Ã: 250 mm, nominal volume flow: 3,534 m³/h, max. volume flow: 4,900 m³/h, max. vacuum: 3,184 Pa, filter area: 22.4 m², chip collection volume: 2 x 250 litres, number of bags: 2 pieces, motor 400 V: 7.5 kW, dimensions (LxWxH): 2,351 x 1,058 x 2,361 mm, sound pressure level: 71 dB(A), weight: 758 kg, after: GS - HO - 07- new exhibition machine -

GAMMA MECCANICA WATER RING PELLETIZER, Model TDA 6, stainlesse steel housing and all parts in contact with water, star blade holder for 4 knives, throughput rate 2,0 Tons/h depending on materials and feeding rate, constructed in 2013, complete with stainless steel drying centrifugeù, screen basket in stainless steel, control panel, photos taken before reconditioning, the machine is offered totally reconditioned, capacity: 2.500 kg/h

GUILLOTINE REEL SLITTER 50 T, Working width 2.500 mm, Working height 1.500 mm, Cutting force 2x25 Ton., No.2 pumps 38+38 lt/min, volume 26,4+26,4 ccm, Speed up: 51 mm/sec, Speed down : (80 Bar) 31-15 mm/sec, Oil tank 255 lt., 15 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydraulic pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer., Force: 50 T

GUILLOTINE REEL SLITTER 35 T, Working width 2.500 mm, Working height 1.500 mm, Cutting force 2x17,5 Ton., No.2 pumps 30+30 lt/min, volume 21+21 ccm, Speed up: 84 mm/sec, Speed down : (80 Bar) 40-20 mm/sec, Oil tank 175 lt., 9 Kw drive 400V 50 Hz, With Knife protection, hydraulic locking system, pull rope emergency system, protection grids, complete with control panel, top lodging, space saving for hydrauliC pack, Users manuals, drawings, CE compliance, 12 month limited warranty, Possible addition of conveyor belt, reel disposer, spare knife on separate offer.

Column-Mounted Crane DEMAG Capacity: 125 kg Arm travel: 3500 mm Height under hook: 2200 mm Total column height: 3150 mm Height under arm: 2700 mm With electric hoist In good condition Voltage: 380 V Weight: approx 250 kg

Process Vessels Net capacity 250 litres, gross capacity 339 litres Pharmaceutical version Agitator Polished interior Product space: Pressure-resistant up to 2.5 bar, operating temperature 138 °C Double jacket: Pressure-resistant up to 4 bar, operating temperature 151 °C mobile

Nominal pressing force ... 250t Table dimensions... 1120 x 800mm Slab dimensions ... 800 x 475mm Plunger adjustment ... 110mm L x W x H ... 1350 x 2550 x 2915mm Machine weight ... 13000kg Number of strokes ... 45/min Control Siemens The machine is in good condition, possible to test under power.

Key data: 600 kN, 132 g/PS, 35 mm

Arburg 320C-600-250 Injection Moulding Machine Number: 238 Availability: in stock Year of production: 2008 Producer: Arburg Screw diameter[mm]:35 Injection weight [g]: 132 Injection pressure [bar]: 1820 Gap spacing [mm]: 320×320 Panel size [mm]: 446 x 446 Min. Form Height [mm]: 200 Control Type: Selogica Tongue: German Installed power [kW]: 23.9 Working hours [h]: 76550 Weight [kg]: 2330 Dimensions [mm]: 3500×1500 Feed hopper: NO Robot Nest: Yes Core String: 1x

Colchester Univ. Lathe Master 2500 Center height 180 mm Center width 600 mm Bore (passage) 40 mm RSF 2-Axis Digital Display Type Z-550 incl. accessories

Key data: 2500 , 60

ENGEL 250T injection molding machine Reference : ES1800/250HL Clamping force : 250T Year : 1999 Working hours : 73 655 h Screw diameter : 60 mm Injectable volume : 763 cm3 Injection pressure : 1969 bars Platen dimensions : 1150 x 900 mm Mold thickness (min/max) : 350 mm x 850 mm Dimensions : 6,92 m x 2,08 m x 2,14 m + with 1 SEPRO robot

H.I.T. NSM 250 RESAWING SAW WITH WOOD FEED FROM THE LEFT (LEFT-HAND MACHINE). The system was fully functional until it was professionally dismantled and dismantled. In addition to the resawing saw with side fabric capping, a model turner, an alignment and centering table and a splitter separation transport included. Specifications Cutting height: 40 - 240 mm Cutting width: 18 - 400 mm / 5-leg variable Width unedged: 750 mm Lengths: 2.50 - 14.00 m Feed: max. 60 m/min Swivel circular saws for side goods cutting with 2 x 7.5 KW motors Saw drive with 2 x 132 KW motors Errors in the information excepted.

Inv. Num. : 8520 Type: MicroMill 2501.15F Producer: MicroStep Created: 2012 Parameters: Control System: iMSNC Software: Asper 3.5 – Basic Operating hours: 15000 h Work table length: 2500 mm Work table width: 1500 mm Source: MicroMill 2501.15F Equipment: Vacuum Suction Cups WITTE 84413 Filtration Nedermann E-PAK 500 3 mechanical grippers with manual pneumatic control on one side Static magazine for 8 tools at the end of the table

Injection moulding machine Arburg 320C 600/250 BJ 2002

E-chain hoist, electric hoist, crane GIS type PK 250 / FFabr. No: 252 243 Year of construction 1988Load capacity 2500 kgHook travel 4 metersMain lifting speed 4.1 m/min. Fine lifting speed 0.9 m/min.- 2 load trainsGood condition; used

E-welding machine, rod electrode welding machine ESAB type LTG 250Masch. No. 736-820-387 Year of construction 1997Power 250 Amp. = 35 % ED 190 Amp. = 60 % ED 150 Amp. = 100 % EDpower setting: infinitely variable - electrode holder with 6 meter connection cable - direct current - fan - air cooling - possibly also TIG welding possible, without hose packageMains connection 380 Volt, 50 Hz, 32 Amp. ConnectorSpace required L x W x H 1200 x 750 x 1050 mmWeight 180 kgGood conditionDevice was originally also suitable for TIG welding

Welding Fume Extraction, Soldering Suction, Laboratory SuctionHigh Vacuum Torch Extraction FUMATOR-APPARATEBAU HEINZ WAGNER Type Minivac 250 DSerien. No. 2902619 year of construction 2004Device air volume flow max. 250 m3/hMinimum air volume flow min. 100 m3/hSeparation efficiency 99.97 %Welding fumes class W3Motor power approx. 0.75 kWNet connection 230 volts, 50 Hz- extraction power infinitely adjustable- 2 pieces extraction connections 45 mm- mechanical air filter (used)- mobile base with 4 fixed castors,

Single column hydraulic press SCHULZ type SES 250Masch.Nr. 04.86.3511/3 Year of manufacture 1986Compressive force 25 ton. Retraction force 10 toProjection 360 mmTable surface 600 x 720 mmPlunger area 500 x 500 mmFailure opening in table 100 mmPin hole 40 mmPlunger stroke 400 mmInstallation height max. 600 mmTable height above floor 935 / 775 mmTank capacity hydraulics 380 litresDrive power 7.5 kWNet connection 380 volts, 50 Hz- Fixed stop adjustment in the press cylinder 180 mm- Light barrier

L + Z Lathe WEWAG Model 250 / 1500Fabr. No. 20953 Year of construction approx. 1975Center width 1500 mmNominal turning diameter over bed 500 mmTurning diameter over bed max. 510 mmCenter height over bed 255 mmTurning diameter over support 300 mmCenter height over support 150 mmSpindle bore 56 mmSpindle speed 18 - 1800 rpm. 24 stepsRotary chuck mount short taper DIN 55022Tailstock inner taper MK 5Drive power 4 kW and 6.7 kW pole-switchable- 3-jaw lathe chuck BISON, 250 mm-

Reciprocating compressor KAESER type EPC 630-250Fabr. No. 1802334 year of construction 1992Volume flow at 6 bar 440 litres/min. Capacity max. 630 litres/min. Pressure capacity 10 barBoiler capacity 250 litersEngine power 3 kWNerg connection 400 Volt, 50 Hz (with 16 Amp. Plug)- 2 cylinders oil-lubricated- Pressure switch set to 10 bar- Runtime from 0 bar to 10 bar Shut-off pressure = 5 minSpace required L x W x H 750 x 700 x 1750 mmWeight approx. 150 kgGood condition; used

Radial drill Manufacturer: Valmer Type: TR 80/2500 SP Year of Make: 2006 Table dimensions: 1,000 x 800 x 560 mm Drilling diameter max.: 80 mm Max. tap diameter: 42 mm Max. spindle axle/column distance: 2,500 mm Max. distance between spindle axle and column: 500 mm Head movement horizontally: 2,000 mm Max. distance between spindle nose and working surface: 2,000 mm Distance between spindle nose and working surface min.: 550 mm Spindle stroke: 450 mm Morse taper: MT 6 Power: 7.5 kW Machine dimensions: 3,730 x 1,400 x 3,825 mm Weight: 11,000 kg

turning length: 2500 mm control: Sinumerik 840 D spindle head: A 11 tool numbers: 48 swing diameter over bed slide: 750 mm swing over bed: 780 mm c-axis: 0,1-30 1/min diameter of quill: 160 mm taper bore: MK 5 tool length - max.: 500 mm weight of tools max.: 15 kg weight of the machine ca.: 27 t dimensions of the machine ca.: 8,4 x 4,0 x 2,5 m Technical details: Nominal turning length: 2,500 mm Swing diameter over bed slide: 750 mm Swing diameter over bed: 780 mm Working height: 1,300 mm Spindle head to DIN 55026: A 11 Bore through: 123 mm Diameter in front bearing: 200 mm Oriented spindle stop: 0-359 degrees Drive power at 100/60 % duty cycle: 37/45 kW Total speed range: 10-2,500 1/min Number of speed ranges: 2 Speed range I: 10-775 1/min Speed range II: 20-2,500 1/min Max. torque at 60 % duty cycle: 2,500 rpm. Torque at 60 % ED: 2,083 Nm (up to 186 rpm) The data for this ad was crea ...

Reference Num.: 4206 Brand: Kodak Type: NexPress 2500 Construction year: 2017 Impressions: 22 mio Available: directly Status: Not in production Location: Deutschland

An AFS printing, laminating and coating system (corona pre-treatment) is available. Roller width: 2700mm, electrode width: 2500mm, max. mechanical speed: 250m/min, max. generator output: 6kW, operating mode: 1- and 5-core operation, electrode material: ceramic, discharge roller: ceramic, cooling type: water-cooled, pressure rollers: both sides. Documentation available. On-site inspection is possible.

Inv. Num. : 8552 Type: TMM-250 M1 Producer: Takisawa Created: 2005 Parameters: Control system: FANUC 180i Max. turning diameter: 350 mm Maximum spindle speed: 4000 1/min Bar diameter: 50.8/76.2 mm Length: 4745 mm Width: 2932 mm Height: 2250 mm Weight: 8500 kg Equipment: 2 spindles and 2 heads with driven tools

A CNC image processing and measuring device Mitutoyo is available. Travel X/Y/Z: 200mm/250mm/100mm, accuracy: 5µm, resolution: 0.5µm, travel speed: 80mm/s, acceleration: 250mm/s², glass table dimensions X/Y: 269mm/311mm, max. workpiece weight: 10kg, weight: approx. 70kg, control: QSPAK Version 3.1. Documentation available. An on-site inspection is possible.

Manufacturer: Mitutoyo Model: QS-250Z Year of Manufacture: 2001 Technical Data: - Measuring Range: X= 200 mm, Y= 250 mm, Z= 100 mm - Accuracy: 5 μm / Resolution: 0.5 μm - Image Capture Unit: 1/3" CCD color camera - Max. Permissible Length Measurement Error: - XY: (2.5 + 0.006L) μm (L = measuring length in mm) - Z: (5 + 0.006L) μm (L = measuring length in mm) - Travel Speed: Max. 80 mm/s - Acceleration: Max. 250 mm/s² - Glass Table Dimensions: 269 x 311 mm - Lighting: - Transmitted light: 12V / 30W Halogen - Coaxial incident light: 12V / 50W Halogen - Fiber optic ring light: 12V / 100W Halogen - Software: QSPAK Version 3.1 - Operating System: Windows 10 Pro - Max. Workpiece Weight: 10 kg - Machine Weight: 76 kg Additional Equipment: - Joystick Box Machine Capabilities: - External measurement - Internal measurement - Distance measurement - Parallelism - Angularity Last calibr ...

AIDA NC2-250(1) 250t eccentric press in excellent condition /ctA2/ Manufacturer: AIDA Type: NC2-250(1) Push force: 160t Year of manufacture: approx. 1991 Stroke length: 170mm Distance above table: (adjustable) 280-400mm Table size: 2700x760mm Bear size: 2100x700mm Electrical power: 3x200V(), 30kW - Japanese standard Pgsc N D D Hou Dxb Tjxop Net weight: 35000kg Size: 2760x2800x3980mm Automatic greasing system. Automatic cutting oil dosing - RAZIOL EST-02 Optionally with disc winder and straightener.

The Dorst DK 250 is a robust used powder compaction press engineered by DORST, offering a substantial pressing force of up to 2500 kN. It supports operations with a maximum withdrawal force of 150 kN and a supporting force in the pressing position reaching 120 kN. Designed for precision, this model includes a 220 mm upper punch stroke with an adjustable travel of 120 mm. The press accommodates a pressing travel and withdrawal travel, each up to 50 mm, making it versatile for various pressing tasks. Operational performance ranges from 6 to 25 strokes per minute, and it provides a filling height of up to 100 mm. The Dorst DK 250 is efficient, consuming approximately 500 liters of air per minute and demanding a connected load of around 60.0 kW. Its dimensions, at 2500 mm in width, 1900 mm in depth, and 4800 mm in height, alongside a weight of approximately 18,500 kg, underscore its solid co ...

Test force: -- kN Dimensions (HxWxD): -- mm weight: 76 kg Condition: Used, ready for use Specification: Mitutoyo image processing and profile measuring device Type: Quick Scope QS-250Z 1J - Used The Quick Scope QS-250Z is used to measure: - Outer diameter - Inner diameter - Distance measurement - Parallelism - Angularity The device was used in quality assurance in a single-shift operation. Technical data: - Measuring range: X = 200 mm, Y = 250 mm, Z = 100 mm - Accuracy: 5 µ / resolution 0.5 µm - Image capture unit: 1/3 CCD color camera - Travel speed max.: 80 mm/s - Acceleration max.: 250 mm/s² - Table dimensions: 269 x 311 mm Lighting: - Transmitted light: 12V / 30W halogen - Coaxial incident light: 12V / 50W halogen - Fiber optic ring light: 12V / 100W halogen Software: QSPAK Version 3.1 Operating system: Win10pro Workpiece weight: max. 10 kg Weight:  ...

Control: SIEMENS drilling diameter: Ø 3 - 25 (18) mm turning speeds: 1000 - 6100 U/min bore slide stroke: 850 mm bore depth: 550 mm spindle distance: 240 mm dimensions: ca. 6 5 2,3 m Shipping weight: ca. 6000 kg : Packing: ca. 10 Lademeter m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: max. 356 mm turning length: 705 mm control: M730 UM Mapps CELOS greates pass round over bed: 920 mm Swing dia. over traverse guideway: 742 mm Main spindle:: turning speed range - main spindle: 4.000 min/-1 power capacity - main spindel: 18,5 / 15 kW spindle nose: JIS A2-8 spindle bore: 80 (91) mm C-Axis: 0,001 ° Subspindel:: Spindle speed range subspindle: 6.000 min/-1 power capacity - Sub spindle: 11 / 7,5 kW spindle bore: 43 mm C-Axis: 0,001 ° axis stroke:: x-travel: 260 mm z-travel: 795 mm Y - Axis: +/-50 mm rapid traverse ( X / Y / Z ): 30 / 10 / 30 m/min turret:: number of toolpositions: 12 pos. Schank height for square tool: 25 mm Drill shank diameter: 50 mm turret change time: 0,27 sec. Driven Tool Positions:: Spindle speed - driven tools: max. 10.000 min -1 power capacity - driven tools: 5,5 / 4,2 kW total power requirement: 41 kVA weight of the machine c ...

R1317 Injection moulding machine ARBURG A 221 - 250 - 55 Year of manufacture 1997 Control Multronica with handling device without hopper and water distributor converted to CF drive but without card, with operating instructions for Arburg and one for the robot Machine was freed up by the purchase of new machines. but no function check from us Price free loaded on truck € 1950.-- +VAT a viewing is desirable Sale only to traders and under the following conditions The machine is considered to have been taken over when it leaves the company, subsequent complaints cannot be taken into account So no guarantee and return.We do not assume any guarantee for compliance with all requirements mentioned in the UVV (accident prevention regulations).

Year of construction 2017 Machine made in Japan! Mazatrol Smooth G Max. turning diameter: 380 mm Jaw spacing: 539.5 mm Max. bar passage: 80 mm Travel X/Y/Z/W 234/100/625/585 mm Main spindle 26/22 kW Max. speed: 4,000 rpm Spindle Nose: A2-8 Sub-spindle 11/7.5 kW Max. speed: 6,000 rpm Spindle Nose: A2-5 12-speed revolver 12 driven tool stations, 5.5 kW Max. speed: 5,000 rpm Tooleye Part catcher for main and sub-spindle Conveyor Bar Feeder Interface 1 set of tool holders, 8 static + 3 driven 15-bar high-pressure pump 1 piece 3-jaw chuck, Kitagawa B210, diameter 254 mm 1 piece collet chuck for counter spindle CE marking Documentation

Control Mazatrol Smooth G Max. turning diameter 380 mm Travel X/Y/Z: 234/100/625mm Main spindle Max. speed: 4,000 rpm Spindle motor drive power: 26 kW Max. bar passage: 80 mm Tool turret 12 tool stations 12 driven tool stations, 5.5 kW Max. speed: 5,000 rpm More options Prog. Tailstock 3-jaw chuck Kitagawa BB210 Parts catcher Interface for rod magazine Tool holder package, 3 powered holders + 8 fixed holders Coolant high-pressure pump, 15 bar Conveyor

Swing diameter over bed/cross slide: 820mm/550mm, distance between centers: 2666mm, max. turning diameter: 610mm, max. workpiece length: 2500mm, travel X/Z: 410mm/2560mm, travel Y: -80mm/100mm, max. workpiece weight without/with tailstock: 500kg/1500kg, tool positions: 12, rapid traverse X/Z/Y: 24m/30m/12m/min, feed force X/Z/Y: 17kN/20kN/17kN. Machine dimensions X/Y/Z: approx. 5500mm/2250mm/2550mm, weight: approx. 15000kg, operating hours: approx. 56089. Documentation available. An on-site inspection is possible. Expected to be available from mid-2026.

A precision glass grinding machine Carl Zeiss for pre-grinding optical workpieces is available. Workpiece spindle speed: 125rpm, tool spindle speed: 7000rpm, feed: 6mm/min, roundness and flatness accuracy: +/-0.005mm, swivel range: 50°, permissible repeatability: +/-0.01mm, measured repeatability (1990): +/-0.005mm. Documentation available. An on-site inspection is possible.

x-travel: 2500 mm y-travel: 620 mm z-travel: 520 mm control: Siemens 840 D Shop Mill table surface area: 3000 x 600 mm table load: kg rapid traverse: 45 m/min turning speed range: 18000 U/min power capacity - milling spindle: 13,7 kW tool taper: HSK 63 A | no. of tools in the magazine: 30 Stück weight of the machine ca.: 9,0 t dimensions: 8,3 x 4,2 x 3,6 m Vertical Machining Center traveling coloumn - chipconveyor - external handwheel - 3D- touch probe - internal coolant 80 bar - band filter system - electr. roof - 1x oil dust collector The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.