kimer 7 36 used for sale

ochdruckcleaner PTC Easypower E similar but no Dynajet, Oertzen, Falch, Woma, Kamat, Denjet , Kärcher, Dibo, ... - Operating pressure: 300-700 bar - Foerder quantity: 15-30 l/min. - Motor: Electric 32A/63A, 3Ph-400V-50Hz 20-30HP/15-22.5kW, 1450 rpm / 1750 rpm - Dimensions: 1,000 x 750 x 850 mm - Kerb weight: approx. 180/210 kg - High pressure pump: Comet three-plunger pump with ceramic plungers - High-quality frame in lacquered steel with corrosion protection - Stainless steel covers - Holding device for pistol with lance - Trolly with industrial wheels - Ergonomic handles for easier maneuverability - Industrial low-voltage power supply (24V) and control unit with star-triangle starter - Safety switch with thermomagnetic relay for motor protection - Operating hour counter - 4 industrial wheels 320 mm - Direct water suction by self-priming pump - Stainless steel relief v ...

oven 700 Uterna Europe 80KW 700 Celsius Ziel des Spannungsarmglühens schoenheider ist die Reduzierung von Eigenspannungen im Material. Solche Spannungen entstehen zum Beispiel durch Gefügeumwandlungen, Kaltverformung und durch spanende Bearbeitung. Wichtig für ein gutes Ergebnis ist nicht nur die richtige buerstlein Temperatur, sondern auch eine umsichtige Abkühlung. Nur so lässt sich eine erneute Spannungsbildung vermeiden. Typischerweise findet das Spannungsarmglühen bei Temperaturen um 600 °C (bei zuvor vergüteten Bauteilen jedoch 30-50 °C unter der letzten Anlasstemperatur) statt. Die Wärmebehandlung ist das häufigste Veredelungsverfahren, mit dem die Eigenschaften der Stähle gezielt verändert und ihre optimalen Gebrauchseigenschaften für den jeweiligen Einsatzzweck herbeigeführt werden. Erst durch eine der Stahlzusammensetzung, dem Verwendungszweck und der Baut ...

SUB: FOR SALE... USED 2 SET BBC COMPLATE VTR 714E-32 T/C AT TURKEY... EMERGENCY HAVE A GOOD DAY. .WE HAVE USED 2 SET BBC COMPLATE VTR 714E-32 T/C AT TURKEY. AND READY TO LOAD ON TRUCK. OUR T/C SPECIFICATION AS BELOW MOY 1988 SERIAL NO.: X. 140769 / 140770 V 01113 R - H 04010 W 05206 E 03010 U 03 I 01800 T 01100 BOTH T/C ARE IN VERY GOOD CONDATION. IF YOU INTEREST PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurlubay BEST of regards; Aliaga marine services E-mail: info@aliagamarine.com PHN/fax: + 90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

Qty. 1 Second-hand roll lathe Mfc.: Herkules Type: WD-700 Built: 1952 General overhauled by Hoesch-MFD in 1990 Centre height: 600 mm Turning length: 2750 mm 2-axis digital display – Mfc.: Micro Wizard Longitudinal drive Standstill torque: 14 Nm Rated revolution: 2500 RPM Feeding range: 5 – 100 mm/min. Rapid speed: 2500 mm/min. Plain drive Standstill torque: 14 Nm Rated revolution: 3000 RPM Feeding range: 5 – 100 mm/min. Rapid speed: 2500 mm/min.

RECON Part number: 0215 4064 / 0400 5112 / 0400 3113 Air start ---------------------------------------------------------------------- ------- Please note: we also have other various RECON parts of different manufacturers / types in stock. We are pleased to provide you with our current stock list. If you have any further questions do not hesitate to contact us

Poly-clip PDC 700 semi-automatic double-clipper, year of construction 2002, for fibrous, plastic, natural and collagen casings, calibres up to 115 mm, sits on a trolley, suitable for following clip sizes: S 735 / 740 / 744, air pressure: 4-6 bar, refurbished. The machine is immediately available and can be tested in Koblenz, Germany.

MADO MSM 764 SUPRA 50 M, 50 Liters bowl cutter, 2 knife speeds, mixing speed forward and reverse, 2 bowl speeds. You are very welcome to test the machine in our facility in Koblenz, Germany.

Makita chain moulder 7101, 110V This article is in good and working condition. Chain mortiser for fast, clean, and precise nicks or cuts through holes in wood. Ideal for timber-frame houses, sheds, huts, restoration and much more.

The NEXUS of 7501 is the cheapest universal hardness testing machine with currently available technology: This hardness testing machine sets the benchmark in quality and price in the device class with proven swivel mechanism (motor switch between Indenter and lens): never get a comparably-equipped machine of this quality at such a fair price. In the standard version are already integrated: USB camera + software for the automatic measurement of impression of hardness -electronically controlled test load application with load cell in closed-loop -integrated boxed PC (WIN 7), LAN connectivity, result export, hardness testing software IMPRESSIONS -integrated touch-screen monitor for a simple, direct touch control -LED lighting, Brinell with ring light The machine is universally suitable for all classic metal hardness testing (test loads 0.5 250 kg). Due to the modern, quality equip ...

AUTOMATIC DOVETAILING machine OMEC 750 I second hand machine machine is utilised to indent dovetails for drawers and various furniture elements CE compliant machine: YES machine also for curved pieces instruction and certification booklet: YES tool / cutter: YES volt. 380/50

specifications: - Load capacity positioning base approx. 750 kg - Flatplate diameter 500 mm - max. workpiece diameter 1600 mm - Height turntable with horizontal position approx. 750mm - Turntable with right,- + left run - Axis of rotation turntable endless 360 ° - Rotation time per revolution 12.5 sec. - Pan left + right - Swivel axis rotation angle 180 ° - Swivel time for 180° swivel angle 10 sec. - 2 x double foot button for turntable + swivel arm - hydr. Clamping bolt for clamping the workpiece in the middle of the turntable - Clamping stroke / clamping distance of the clamping bolt 32 mm - Clamping force pressing / pulling 80 / 48.9 kN - Clamping cylinder female thread M 27 x 40 - Positioning control SIEMENS - Operation manually or via control - Space required approx. W 1500 x D 2800 x H 1100 mm - Weight approx. 2500 kg - separa ...

Horn pump Cabinet consisting of: -2 x Horn pump MP 5 (700 l / min) -> For heating oil, diesel and bio-diesel Technical data: Max capacity: 700 l / min Supply voltage: 400 / 50 V / Hz Capacity: 2, 5kW Inlet: DN 80 Pressure connection: DN 80 Maximum suction height: 4, 5 m Protection class: IP 44 Pump Cabinet is painted and fully functional! The pumps can be expanded like at extra charge out of the closet, but we would prefer a sale as a complete package!

Wheel diameter: 700 mm Cutting height: 420 mm cutting width: 680 mm Motor output: 3 kW Table dimensions: 695 x 990 mm Table tiltable: 45 Grad Dimensions (L/W/H): 1260x840x2270 mm machine weight ab.: 400 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

The CD50 series of our high-pressure machines covers a pressure of 230 to 2000 bar and a volume flow of 7 to 74 l/min. The pump is powered by a water-cooled 4-cylinder Toyota diesel engine. The fully enclosed frame is made of hot-dip galvanized steel to ensure a long service life and corrosion resistance. The frame is primed and then painted. The machine only requires a footprint of 1550 x 920 mm. Under the frame 4 rubber feet are mounted. In addition, the machine has forklift pockets and lifting eyelets attached to all four corners. For the protection and storage of, for example, high-pressure hoses, a galvanized roof plate provides. Similar but no Dynajet, Falch, Hammelmann, Kamat, Kärcher, Oertzen, Uraca, Woma, etc. Available models: ----- Model Pressure Volume Flow CD50-230 230 bar 74 Lpm CD50-400 400 bar 40 Lpm CD50-500 500 bar 33 Lpm CD50-700 700 bar 25 Lpm CD50-1000 100 ...

SOLD! ABC ENGINE 8XDXC 886KW @ 750 RPM diesel engine ABS BJ 2002

The universal rotary machine for top flexibility in self-adhesive labelling. The Pago System 630 is based on a sturdy rotary machine and the powerful Pagomat 6 series labelling heads. The system is designed for self-adhesive labelling of all kinds of products and for applications in every industry. labeler PAGO SYSTEM 630M producer: PAGO TYPE: 720.12T.S2.E2 Year: 2003

The FORNI INDUSTRIALI FIBEX COMBI 6GX-10.130-7110.2E.270 brazing furnace was built by the Italian company Forni Industriali Heat Treating Plants in 2007. The furnace is used for soldering steel elements with solder paste at temperatures up to 1120 degrees Celsius. At the entrance and exit of the furnace, two pairs of gas burners (so-called safety pilots) are installed to prevent the escape of the protective atmosphere outside the furnace. Electric heaters powered by thyristor temperature regulators are responsible for the proper temperature in the furnace. The belt furnace has a conveyor speed adjustment in the range from 0 to 500 mm / min, and the working length of the soldering zone is 7100 mm. The furnace for brazing steel elements was modernized in 2021 - the thermal insulation and the cooling module for sections 1 and 2 were replaced. The cost of the modernization was 70,000 Euro.  ...

Horiba Here we offer you a Horiba exhaust system Mexa 7100D. Including JAG-10-000-061 bottle trolley approx. 1200 x 1064 x 802 mm and OVN-724A Stationary exhaust gas measurement before/after exhaust gas aftertreatment, Assessment of exhaust gas aftertreatment systems Modal analysis (dynamic or transient analysis) during transient operations Analyzer for CO/CO2 (HC, NO, N2o, SO2), O2, THC 200 operating hours Weight 620 Kg Year of construction 2016 Type: Mexa 7100D Condition: used Pick-up from location Scope of delivery: (See picture) (Changes and errors in the technical data, information reserved!) We are happy to answer any further questions you may have on the phone.

Type: 9T S2/E2 SENSITIVE Model: A-720 Machine capacity: 135 bottles per minute

Attachment: eccentric screw pump Manufacturer: Allweiler Type: SLBP 720-1 Machine number: 7640010 Year of construction: 1989 Power: 67-484 l / min Speed gear: 50-280 RPM. Engine: Bauknecht Power: 5.5 kW, 380 V Speed: 1440 RPM Connection suction side: DN 100 Port side: DN 100 Length: 1800 mm Condition: used, ready

Heraeus Vötsch Temperature Test Chamber Here we offer you a Heraeus Vötsch temperature test chamber. Heraeus Vötsch temperature test chamber air-cooled Housing dimensions: Width 820 mm Depth 840 mm Height 1670 mm Interior: Width 550 mm Depth 350 mm Height 550 mm Rated voltage: 230V +6/-10% 1/N 50Hz Rated power: 3.2 kW Rated current: 14.5 A Temperature range -70°C to + 180°C 2X lateral implementation 9cm Refrigerant VK R 452 A Weight approx. 300 kg Type: HT 7020 For you as a buyer for security the following information! The following points are carried out in advance at our offered chambers: 1. Functional check and replacement of necessary components 2. New filling with legally compliant refrigerant 3. Leak test with certificate 4. After successful verification, the chambers are subjected to a test run, which is monitored with calibrated devices. Condition: used ...

Heraeus Vötsch Temperature Test Chamber Here we offer you a Heraeus Vötsch temperature test chamber. Heraeus Vötsch Temperature Test Cabinet Water Cooled Temperature range -70°C to + 180°C Temperature deviation over time ±0.1 to ±0.5 K Temperature deviation ±0.5 to ±2.0 K Temperature change rate cooling 7.5 K/min Temperature change rate heating 7.5 K/min Heat compensation +20°C 3000 W Heat compensation -20°C 3000 W Test room dimensions: Width 580 mm Depth 450 mm Height 750 mm External dimensions: Width 870 mm Depth 1280 mm Height 1575 mm Observation window: Width 300 mm x height 540 mm Test room volume 190 liters Rated voltage: 3/N/PE AC, 400 V ±10 %, 50Hz Rated power: 10.5 kW Rated current: 22 A Fuse, on site: 32 A sluggish Sound level at a distance of 1m (free field measurement) < 69dB (A) lateral feedthrough 50 cm / 125 cm Cabinet is water-cooled Refri ...

Waelzpistonblowese Booster Manufacturer: Leybold Typ: RUVAC RA 7001 Status: Generalueberholt Including: repainting, engine restocking, electric check Performance: 12 months Delivery time: from stock; ready for use

- double-sided bubbling machine Metabo 7445 - Metabo 72730 - 4 kW - shaft diameter 35 mm - 1500 min-1; ready for use

Heraeus Vötsch Temperature Test Chamber Here we offer you a Heraeus Vötsch temperature test chamber. Heraeus Vötsch Temperature Test Cabinet Water Cooled Temperature deviation over time ± 1 K Temperature deviation spatially ± 2 K Housing dimensions: Width 820 mm Depth 840 mm Height 1670 mm Interior: Width 550 mm Depth 350 mm Height 550 mm Rated voltage: 230V +6/-10% 1/N 50Hz Rated power: 3.2 kW Rated current: 14.5 A Temperature range -70°C to + 180°C 2 x lateral implementation 9cm Weight approx. 260 kg Refrigerant: R404A and R23 For you as a buyer for security the following information! The following points are carried out in advance at our offered chambers: 1. Functional check and replacement of necessary components 2. New filling with legally compliant refrigerant 3. Leak test with certificate 4. After successful verification, the chambers are subjected to  ...

- double sided brishing / deburring machine Metabo 7445 / Metabo 72730 - 4 kW - shaft diam. 35 mm - 1500 rpm; ready for operation

ALFA-LAVAL LKH 80/245 FSS 75kW hygienic centrifugal pump. Capacity: 280 m³/hr, 5 bar. Electric motor: 75kW. comes from a TETRAPAK Alcross Bactocatch system. Built in 2008. in very good condition.

Bitzer Screw Compressor NEW Type HSK 7471-90-40P Stroke volume 250cbm/h 90 hp electrical power. New

Heraeus Vötsch Temperature Test Chamber Here we offer a Heraeus Vötsch temperature test chamber. Heraeus Vötsch temperature test chamber air-cooled Basic unit type VT 7021 Operator terminal color touch panel Microprocessor monitoring and control MINCON/32 independent adjustable temperature limiter tmin / tmax adjustable software temperature selector limiter min./max. serial interface RS 232 Schuko socket potential-free contact for test material shutdown Refrigeration unit air-cooled 1 door lockable, one-hand operation Calibration of 2 temperature values Mobile version 1 bushing, NW 80 mm, right Test room volume 210 liters Temperature range -70°C to +180°C Temperature deviation over time ± 0.2 to ± 0.5 K Temperature deviation spatially ± 0.5 to ± 1.5 K Temperature change rate heating 2.5 K/min Temperature change rate cooling 2.5 K/min heat compensation 800W  ...

Heraeus Vötsch Climate Test Chamber Here we offer you Heraeus Vötsch climate test chamber. Temperature Climate Test Chamber Air Cooled Standard: Touch panel and independent, adjustable temperature limiter 32 Bit S! MPAC control with touch panel Potential-free contact for test material shutdown Independent, adjustable temperature limiter tmin/tmax Psychrometric humidity measurement system Interface TCP/IP 1 pipe feedthrough 50 mm Refrigeration circuit air-cooled Coolant R23 & R404A Temperature range -70 to +180°C Temperature deviation over time ±0.3 to ±1.0 K Temperature homogeneity spatially ±0.5 to ±2.0 K Change speed heating 3.5 K/min Change speed cooling 2.5 K/min Services for climate tests: Humidity range 10 to 98% Test room dimensions: Width 470 mm Depth 345 mm Height 400 mm External dimensions: width 760 mm depth  ...

Engine number: 2 472 863/64 Power: 22 HP Speed: 2000 1/min overhauled, no generator, starter Price Excl. VAT, subject to prior sale Photos on demand

Engine number: 5 478 583 Power: 486 HP Speed: 1650 1/min overhauled, no generator, no alternator, with injection timing Price Excl. VAT, subject to prior sale Photos on request

GUK Slitting Machine RS 21/760 Technical details: -No double bows, false bows and no risk of mixing! -Insensitive to static charge -approx. 20% cost savings compared to processing batch goods -Automatic control of the cutting position -Synchronous control of the print mark -Installation of code readers additionally possible -Storage in maintenance-free needle and ball bearings -Paper roll on top, single or double roll stand -With and without integrated adhesive table -Drive left or right, with chain or timing belt -Smallest fold 15 mm -With automatic roller changer ARW 21 Specifications: -Min. format: (WxL) 60 mm x 105 mm -Format: (WxL) 210 mm x 315 mm -Roller outer diameter: max. 600 mm -Roll core diameter: Europe 70 mm USA and Japan 76 mm or 152.4 mm or 3 inch or 6 inch -Power: 300/minute, depending on section length -Capacity: For paper roll by. 600 mm, sectio ...