kasto speed used for sale

Press capacity: 50 ton Ram stroke: 54 mm Slide adjustment: 80 mm Shut height (stroke down, adjustment up): 303 mm Table surface area : 810 x 550 mm Number of strokes: 65 - 400 s.p.m. Weight of machine approx.: 7,5 ton Main Motor: 11 kW

Press capacity: 100 ton Ram stroke: 300 mm Slide adjustment: 125 mm Shut height (stroke down, adjustment up): 600 mm Free frontal opening L-R: 2.020 mm Free lateral opening F-B: 620 mm Table surface area : 2.000 x 1.000 mm Slide area: 2.000 x 900 mm Hole in table: 1.700 x 300 mm Number of strokes: 10 - 50 s.p.m. Table height over floor: 1.200 mm Required power: 39 kW Height over floor approx.: 4.400 mm Dimensions L x W x H: 5.166 x 2.500 x 4.400 mm Weight of machine approx.: 38 ton

Press capacity: 40 ton Ram stroke adjustable: 8 - 50 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 310 mm Free frontal opening L-R: 820 mm Table surface area : 810 x 450 mm Slide area: 720 x 350 mm Hole in table: 600 x 110 mm Number of strokes: 100 - 1.000 s.p.m. Table height over floor: 1.030 mm Required power: 19,5 kW Weight of machine approx.: 6,8 ton

: 40 1008 rated current: 20 A voltage: 24 V weight of the machine ca.: 3,5 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press capacity: 40 ton Ram stroke adjustable: 8 - 50 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 290 mm Free frontal opening L-R: 600 mm Free lateral opening F-B: 190 mm Table surface area : 600 x 500 mm Slide area: 600 x 400 mm Hole in table: 500 x 110 mm Number of strokes: 65 - 400 s.p.m. Table height over floor: 1100 mm Required power: 32 kW Height over floor approx.: 2.800 mm Weight of machine approx.: 6,2 ton

Pressure total: 315 ton Ram stroke: 160 mm Slide adjustment: 100 mm Shut height (stroke down, adjustment up): 1.050 mm Free frontal opening L-R: 2.740 mm Free lateral opening F-B: 1.500 mm Distance between oil tray: 2.400 mm Table surface area : 2.740 x 1.800 mm Slide area: 2.400 x 1.700 mm Number of strokes: 10 - 60 s.p.m. Required power: 75,5 kW kW Working hours machine: 77.341 h Height over floor approx.: 5.500 mm Dimensions L x W x H: 5.400 x 3.300 x 5.700 mm Weight of machine approx.: 80 ton Control: Siemens S5

FOR SALE: BRUDERER BSTA 50USL High-Speed Stamping Press With Automatic Strip Feeder BBV 190 500 kN | 100–1120 spm | Fully automatic | Top-tier Swiss quality Technical Highlights: Nominal force: 500 kN Stroke rate: 100–1120 strokes per minute Working hours: 41000 h Main motor: 22 kW Control voltage: 24V DC Power connection: 400V / 50Hz / 62 kVA Adjustable stroke: 16 / 19 / 25 / 32 / 38 /44 / 51 mm Shut height adjustment: 64 mm Working Dimensions: Max tool installation width: 1100 mm Strip pass width: up to 256 mm Ram area: 980 × 420 mm Table area: 1080 × 650 mm Strip entry height adjustable: 60–140 mm Max strip width: 120 mm Max feeding pitch: 85 mm Max material thickness: 4 mm Feeding angle: 180 Deg Machine Dimensions (with BBV 190): Machine footprint (L × W × H): 2407 × 1278 × 3150 mm Weight (approx.): 8,000 kg Equipment Includes: Feeder BBV 1 ...

CONTROLS   conventional PRESS FORCES   total force (nominal): 75 to PRESS TABLE   table surface (left-right): 1250 mm   table surface (front-back): 1110 mm SLIDE   table surface (left-right): 960 mm   table surface (front-back): 750 mm SLIDE (MECHAN. PRESS)   slide adjustment: 80 mm   stroke adjustment: yes   stroke min.: 10 mm   stroke max.: 50 mm   stroke rate (min.): 120 /min   stroke rate (max.): 600 /min STRIP-FEEDER   feeder type: roll feeder   sheet width max.: 300 mm ELECTRICAL SPECIFICATIONS   total power consumption: 15.5 kW DIMENSIONS / WEIGHTS   total weight approx.: 13500 kg ATTACHMENTS (PRESSES)   strip feeder: yes   feeder type: roll feeder

A Thyssen Henschel intensive mixer with an AEG motor is available. Volume: 1000l, double jacket volume: 95l, max. operating temperature: 200°C, permissible operating pressure: 5bar, speed: 532rpm, motor type: KA7318M-BB059-Z, power: 184kW. Including tools type FM, floor scraper and fluidizing blades. On-site inspection is possible.

Multi-speed machine with flexible shaft BIAX type MB 4-2Masch. No. 9/50/55 Year of construction approx. 1970Length of the flexible shaft: 2 metersSpeed: 900 - 9000 rpm. infinitely variableMotor speed: 3000 rpm. Motor power: 1.2 kW = 1.5 HPerg connection: 380 volts, 50 Hz- handle straight grinder with collet 6 mm- swivel and rotatable foot transport trolley with 2 drawersOverall dimensions: 850 x 550 x 1100Weight: approx. 80 kggood conditionUniversal for milling, grinding and polishing work; used

Quick-opening milling spindle HENNINGER type 814 / 5131 / 1:5 / 15000speed max. 15000 rpm at 70% EDratio ratio 1:5Power transmission up to approx. 2.5 kWProduct dimension 110 mm (machine spindle to clamping nutTool holder MK4 with tightening thread M16Collets type OZ16 6 / 8 / 9 / 10 / 11 / 12 / 12.5 / 13 / 14 mmWeight 6.5 kgGood condition; used

Press capacity: 50 ton Ram stroke adjustable: 16 - 51 mm Slide adjustment: 78 mm Shut height (stroke down, adjustment up): 300 mm Table surface area : 930 x 590 mm Number of strokes: 620 - 1.120 s.p.m. Required power: 40 kW Dimensions L x W x H: 3.900 x 1.400 x 3.065 Weight of machine approx.: 9 ton

Polar 92X High speed cutter Year 2004 Program Large side tables Spare knife Photocells

A total of 10 deionization devices Keyence are available. Ion generation: +/-7000V, ion balance: +/-30V, max. effective range: approx. 3000mm, working distance range: 50mm-2000mm, electrode material: tungsten, applications: plastics/films/coating/electronics/packaging. Documentation available. An on-site inspection is possible.

threading: 30 M bore capacity in steel (diameter): 40,0 mm workpiece height max.: 380 - 785 mm arm length: 985 mm spindle taper: 4 MK boring head swiweling right/left: -80 / +80 Grad turning speeds: 50 - 2000 U/min table surface area: 1210 x 520 mm column diameter: 220 mm column diameter: 220 mm table surface area: 1.210 x 520 mm quill stroke: 200 mm feed range - spindle: 0,08 - 0,5 mm/U total power requirement: 2,2 kW weight of the machine ca.: 2.800 kg. dimensions of the machine ca.: 2,45 x 1,2 x 2,72 m characteristics - A variety of clamping and machining options thanks to the construction-related construction - Electromotive height adjustment of the drill head without adjusting the Drilling position, ideal for deep hole drilling - Drill head can be swiveled 180 °, boom can be moved back and forth and horizontally pivotable - Thread cutting device and 6 automatic drilling feeds in ...

Press capacity: 63 ton Ram stroke adjustable: 8 - 60 mm Slide adjustment: 80 mm Shut height (stroke down, adjustment up): 300 mm Table surface area : 810 x 550 mm Slide area: 700 x 420 mm Hole in table: 550 x 140 mm Distance between oil tray: 700 mm Table height over floor: 920 mm Number of strokes: 65 - 400 s.p.m. Weight of machine approx.: 8 ton Dimensions L x W x H: 2935 x 1170 x 3000 mm Main Motor: 11 kW

MÜGA high-speed drilling-milling centre TYPE: S 3030 with 2-fold pallet changer incl. chip conveyor (similar to FANUC or BROTHER) Control: MITSUBISHI M70 Travel: X/Y/Z: 300 x 250 x 250 mm Spindle speed: 60 – 10,000 rpm. Motor power: 100//30% ED 2.2/3.7 kW Star turret: 12-speed Tool change time: 1.6 sec. Chip-to-chip time: 2.5 sec. Tool holder: BT 30 - 45° 2-fold pallet table: LxW: 400 x 250 mm Chip conveyor ejecting backwards Rapid traverse: X/Y/Z: 48/48/60 m/min. Installation area: L x W x H: 2690 x 1570 x 2370 mm Weight: 3300 kg Total connected load: 11.5 kW Description: The machine is suitable due to the 2-fold pallet system, as well as the high rapid traverses and fast chip-to-chip time for series part production. From 2011 to 2020, it was used in single-shift operation exclusively for ALU machining. There is no hour meter. The machine is still un ...

manufacturer/tradename: Corning 6775 AC/DC input 120 V AC feature CE compliant Parameter 0-3400 rpm speed L × W × H 14 cm × 16 cm × 13 cm For any inquiries, please send an email : f33gmpyahoo.com Attn : Jescica Tan

Key data: 4350 mm, 1250 mm, 1200 mm

FIDIA K 211 – 5-axle CNC machining center for complex shapes in tool and mold making. Equipped with a simultaneous 5-axis twist milling head (A-Y-C) The FIDIA C20 CNC control system ensures fast data processing, precise path guidance and reliable process control. With a spindle speed of up to 24,000 rpm, the machine is optimally designed for high-speed milling and fine surface quality.

Key data: 2650 mm, 1250 mm, 1200 mm

FIDIA K 211 – 5-axle CNC machining center for complex shapes in tool and mold making. Equipped with a simultaneous 5-axis twist milling head (A-Y-C) The FIDIA C20 CNC control system ensures fast data processing, precise path guidance and reliable process control. With a spindle speed of up to 24,000 rpm, the machine is optimally designed for high-speed milling and fine surface quality.

CHIRON FZ08 KS Magnum High Speed Plus (HSP) High-Speed Machining Center (HSP) TECHNICAL FEATURES: Year: 2006 NC Type: FANUC 18i-MB5 Number of axes: 7 X-axis travel: 450 [mm] Y-axis travel: 270 [mm] Z-axis travel: 310 [mm] X, Y and Z fast travel speed: 75000 [mm/min] Maximum diameter in bar turning spindle: 32 [mm] Maximum speed Turning spindle: 8000 [rpm] Maximum power turning spindle: 12 [kW] A-axis angular travel: 360 [°] A-axis indexing accuracy: 0.001 [°] B-axis angular travel: -20° / +115 [°] B-axis indexing accuracy: 0.001 [°] Pin Attachment: HSK40 Maximum speed Spindle: 30000 [rpm] Number of tool magazine stations: 40 Turning part by robot (6th side machining): Yes RS232 Port: Yes Installed power: 17 [kVA] Supply voltage: 400 [V] Operating hours: 9911 [h] Dimensions: 1500 x 2600 x 2300 [mm] Weight: 3400 [Kg] EQUIPMENT INCLUDED: x1 RENISHAW p ...

Key data: 300 mm, 1130 mm, 300 mm

4 Spindle High Speed Train Milling Machine, ANGER, HCP 10/5, 2005 Control : NUM, very few operating hours. Methods: X-300, Y-1130, Z-300, - 4-axis +/- 180 degrees 4 high frequency spindles : Precise 60000 / 160000 / 18000 / 16000 rpm , rpm Tool holder : Collets depending on the spindle Chip conveyor, ATC, recooling unit, external measuring system Renishaw Power consumption 41 kw

Key data: 300 mm, 1130 mm, 300 mm

4 Spindle High Speed Train Milling Machine, ANGER, HCP 10/5, 2005 Control : NUM, very few operating hours. Methods: X-300, Y-1130, Z-300, - 4-axis +/- 180 degrees 4 high frequency spindles : Precise 60000 / 160000 / 18000 / 16000 rpm , rpm Tool holder : Collets depending on the spindle Chip conveyor, ATC, recooling unit, external measuring system Renishaw Power consumption 41 kw

Key data: 5 , 10

Oil lubricated screw compressor Cooling: Air-cooled design Drive: Efficient IE3 motor, belt drive Control: Speed-controlled with frequency converter Control: Infologic² Connect Refrigeration Dryer: Integrated Filtration optionally available Performance data Volume flow at operating pressure 7.0 bar 0.33 - 0.75 m³/min Operating pressure min. / max. 4.0 / 10.0 bar Total power consumption at 9.5 bar / full load 7.7 kW Rated power motor; IP55 5.5 kW Oil volume 3.2 lt Pressure dew point refrigeration dryer approx. +3 °C Installation data Ambient conditions min. / max. 1 / 46 °C Cooling air demand 1140 m³/h Free fan pressure 30 Pa Sound level 61 dB(A) Voltage / PH / Frequency 400 / 3 / 50 V / Ph / Hz Refrigeration dryer power (230V/50Hz) 0.19 kW Dimensions and weight Length x width x height 1540 x 600 x 1375 mm Weight 230 kg Compressed air outlet 1/2 "  ...

Key data: 7 , 10 , 1

Oil lubricated screw compressor Cooling: Air-cooled design Drive: High-frequency motor with 1:1 direct drive Control: Speed-controlled with frequency converter Control: Aircontrol 5.0 (4-20mA) Refrigeration dryer: Integrated, refrigerant R134a Filtration: incl. cyclone separator Performance data Volume flow at operating pressure 7.0 bar 0.28-1.25 m³/min Operating pressure min. / max. 5.0 / 12.5 bar Total power consumption at 10.0 bar / full load 9.3 kW Rated power motor; IP55 7.5 kW Oil quantity 3.5 lt Pressure dew point refrigerant dryer (20°C 100% RH) +3 °C Installation data Ambient conditions min. / max. 1 / 46 °C ∆ T above coolant temperature 8 °C Cooling air requirement 2200 m³/h Free fan pressure 30 Pa Sound level 62 dB(A) Voltage / Frequency 400 / 50 V / Hz Refrigeration dryer power (230V/50Hz) 0.27 kW Dimensions and weight Length x width ...

Klopp 1000 Quick Planer Total width: 150 cm Overall length: 3,330 cm Total height: 170 cm Planing width: 750 mm Working length: 1000 mm Table width: 900 mm

for Mitsubishi S6R S6R2 S12R GAC Speed control unit 15674-4-01 incl. speed sensor 17301-3-01 incl. plug 234958-12

The machine is in good technical condition, testing is possible by prior arrangement. X-axis travel distance:3,200 mm Y-axis travel:1,400 mm Z-axis travel:900 mm X-axis rapid traverse:16 m/min Y-axis rapid traverse:20 m/min Rapid traverse: m/min Y-axis feed rate:10 m/min Z-axis feed rate:10 m/min Nominal (apparent) power:50 kVA Controller manufacturer:Fanuc α 30/3000i 7.0 Workpiece length (max.):4,000 mm Workpiece width (max.): max. 000 kg Total height: 4,500 mm Total length: 8,130 mm Total width: 4,150 mm Table width: 1,200 mm Table length: 3,200 mm Table load: 8,000 kg Total weight: 17,000 kg Maximum spindle speed: 8,000 rpm Diameter: 50 mm Tool length: 350 mm Tool diameter: 127 mm Tool weight: 20 g Equipment: documentation / manual, chip conveyor, infinitely adjustable speed

Danube DR 23 - High Radial Drilling Machine -Drilling capacity / steel approx. 28mm -Projection approx. 700mm -Morse taper MK 3 -Speed range 70-1550 rpm - Gearbox -Feed range 0.075-0.3mm -Drilling depth 130mm -Tapping device -Hydraulic clamping -Documentation Dimensions: Hjbkn Asvw D Smeu S Tol LxWxH 2x1.7x1.9 meters / Weight 1900Kg

The machine is in good technical condition, testing is possible by prior arrangement. X-axis travel distance:1,035 mm Y-axis travel:560 mm Z-axis travel:510 mm X-axis rapid traverse:30 m/min Y-axis rapid traverse:30 m/min Z-axis rapid traverse:30 m Y-axis feed length:560 mm Z-axis feed length:510 mm X-axis feed:30 m/min Y-axis feed speed:30 m/min Z-axis feed speed:30 m/min Rated (apparent) power:17 kVA Torque:83 Nm Controller manufacturer: Sie 137 mm Overall width:3,355 mm Table width:560 mm Table length:1,200 mm Table load:1,000 kg Overall weight:4,250 kg Spindle speed (min.):20 rpm Maximum spindle speed:8 000 rpm Tool operation:20 Tool length:300 mm Tool diameter:80 mm Tool weight:6,000 g Equipment:documentation / manual, chip conveyor, infinitely adjustable speed

The machine is in good technical condition, after prior agreement it is possible to test it. Control system: Siemens Sinumerick 840D Total hours: 12,058 h Operating hours: 5,039 h Worktable length: 1200 mm Worktable width: 5 Spindle rotation: 8000 1/min Number of axes: 3 X-axis travel: 1035 mm Y-axis travel: 560 mm Z-axis travel: 510 mm

CHIRON FZ 08K S Magnum HSP High-Speed CNC Machining Center TECHNICAL FEATURES: Year: 2007 NC Type: FANUC 18i-MB5 Number of axes: 7 X-axis travel: 450 [mm] Y-axis travel: 270 [mm] Z-axis travel: 310 [mm] X, Y and Z fast travel speed: 75000 [mm/min] Maximum diameter in bar turning spindle: 32 [mm] A-axis angular travel: 360 [°] A-axis indexing accuracy: 0.001 [°] B-axis angular travel: -20° / +115 [°] B-axis indexing accuracy: 0.001 [°] Pin Attachment: HSK40 Maximum speed Spindle: 30000 [rpm] Number of tool magazine stations: 40 Installed power: 17 [kVA] Supply voltage: 400 [V] Dimensions: 1500 x 2600 x 2300 [mm] Weight: 3400 [Kg] EQUIPMENT INCLUDED: x1 RENISHAW probe type TS27R x1 Spindle Cooling Unit x1 watering tray x1 unit for 6th side machining x1SCHUNK gripping system x84 HSK40 Type Tool Holder x14 Collet Type F35 x1 Electrical Cabinet Air C ...

Biete Getrieberegglerkarte Deutz mit der Teilnr. 1240 4590EE for sale.

High-speed mixers Manufacturer: Henschel Type FM-4 Serial No. 80 5002 Double jacket for heating and cooling Total capacity 4 liters Working capacity 3 liters

High-speed textile braiding machine for lace making, model KY-T12-NCF, Kyang Yhe brand. Configuration of 12 spindles, suitable for the production of round and flat cords. Compatible with materials such as polyester, nylon, cotton, elastic yarn and PP. Typical applications: round cords, flat cords, elastic cords (e.g. for face masks) and decorative elements. Power supply: 380 VAC, 50 Hz, industrial three-phase system. Equipped with individual speed controllers and digital production counter. Serial number: 30010/3. Year of manufacture: 2021. Auction-ID: A7-44783-1

High-speed textile braiding machine for lace making, model KY-T12-NCF, Kyang Yhe brand. Configuration of 12 spindles, suitable for the production of round and flat cords. Compatible with materials such as polyester, nylon, cotton, elastic yarn and PP. Typical applications: round cords, flat cords, elastic cords (e.g. for face masks) and decorative elements. Power supply: 380 VAC, 50 Hz, industrial three-phase system. Equipped with individual speed controllers and digital production counter. Serial number: 30010/3. Year of manufacture: 2021. Auction-ID: A7-44783-2

High-speed textile braiding machine for lace making, model KY-T12-NCF, Kyang Yhe brand. Configuration of 12 spindles, suitable for the production of round and flat cords. Compatible with materials such as polyester, nylon, cotton, elastic yarn and PP. Typical applications: round cords, flat cords, elastic cords (e.g. for face masks) and decorative elements. Power supply: 380 VAC, 50 Hz, industrial three-phase system. Equipped with individual speed controllers and digital production counter. Serial number: 30010/3. Year of manufacture: 2021. Auction-ID: A7-44783-3

Hanging file trolley steel grey 2-speed approx. 80x50x60cm (WxDxH)

High-speed textile braiding machine for lace making, model KY-T12-NCF, Kyang Yhe brand. Configuration of 12 spindles, suitable for the production of round and flat cords. Compatible with materials such as polyester, nylon, cotton, elastic yarn and PP. Typical applications: round cords, flat cords, elastic cords (e.g. for face masks) and decorative elements. Power supply: 380 VAC, 50 Hz, industrial three-phase system. Equipped with individual speed controllers and digital production counter. Serial number: 30010/3. Year of manufacture: 2021. Auction-ID: A7-44783-5

High-speed textile braiding machine for lace making, model KY-T12-NCF, Kyang Yhe brand. Configuration of 12 spindles, suitable for the production of round and flat cords. Compatible with materials such as polyester, nylon, cotton, elastic yarn and PP. Typical applications: round cords, flat cords, elastic cords (e.g. for face masks) and decorative elements. Power supply: 380 VAC, 50 Hz, industrial three-phase system. Equipped with individual speed controllers and digital production counter. Serial number: 30010/3. Year of manufacture: 2021. Auction-ID: A7-44783-4

Adjustable geared motor, variable speed geared motor, electric motor -Engine power: 9.2 kW -Speed range: 34-207 rpm -Electric motor: SEW type DFV132ML-4 -Transmission: SEW type R82-VU4HS -Motor: adjustable -Drive shaft: Ø 50 mm -Design: B3 -Protection rating: IP54 -Dimensions: 900/380/H670 mm -Weight: 247 kg

Adjustable geared motor, variable speed geared motor, electric motor -Manufacturer of adjustable gearbox Lenze Type: 11.715.03.04 -Manufacturer of gearbox: Lenze, Type: 52.145.04.100 -Manufacturer Motor Hanning Type: EeDF71L/2 -Motor power: 0.55 kW -Speed range: 46-264 rpm -Motor: adjustable -Drive shaft: Ø 25 mm -Design: B5 angle -Quantity: 1 motor available -Price: per piece -Dimensions: 480/220/H220 mm -Weight: 25 kg

Adjustable geared motor, variable speed geared motor, electric motor -Manufacturer of gearbox: AEG Motor manufacturer: AEG -Motor power: 0.175 kW -Speed range: 450-4000 rpm -Motor: adjustable -Design: B3 -height of shaft axis: 80 mm -Drive shaft: Ø 14 mm -Quantity: 1 motor available Price: per piece -Dimensions: 380/200/H240 mm -Weight: 22 kg

Adjustable geared motor, variable speed geared motor, electric motor -Manufacturer: MOTOVARIO TKFL/10 gearbox -Manufacturer: ASEA MT80B19F100-4 engine -Motor power: 0.75 kW -Speed range: 190-1000 rpm -Motor: adjustable -Drive shaft: Ø 24 mm -Design: B5 -Quantity: 1 motor available -Price: per piece -Dimensions: 445/255/240 mm -Weight: 29 kg

High speed radial drilling machine, radial drilling machine, drilling machine, boom drilling machine, high speed radial drilling machine -Clamping table: 400 x 1100 mm -Projection: 930 mm -Taper mount: MK4 -Engine power: 1.35/1.8 kW -Speed: 41-1700 rpm -Columns: Ø 200 mm -Spindle stroke: 125 mm -Thread cutting device: YES -Feed: 0.075 - 0.3 mm/rev -Dimensions: 1800/1235/H2240 mm -Weight: 1500kg

Adjustable geared motor, variable speed geared motor, electric motor -Manufacturer of gearbox: Lenze, Type: 11.431.10.08.1 -Manufacturer Motor ATB Type: ERFY 0.55/4-7 -Motor power: 0.37 kW -Adjustable speed range: 111 to 617 rpm -height of shaft axis: 50 mm -Drive shaft: Ø 16 mm -Number: 2 motors available -Price: per piece -Dimensions: 370/254/H190 mm -Weight: 14.5 kg

GeneralTraveling column machine; Control: CELOS X with HEIDENHAIN TNC7 Technical DataFeed rate longitudinal/transverse/vertical50000/50000/50000 mm/minRapid traverse longitudinal/transverse/vertical80/80/80 m/minWorking area 1Longitudinal2000 mmCross800 mmVertical850 mmTool changerType of magazineChain Number of tools50 Max. tool weight6 KgMax. tool length300 mmMax. tool diameter with occupied adjacent pockets80 mmMax. tool dia. with free neighbouring pockets130 mmSwivelhead, B-axisControlled NC swivel milling head 12,000 rpm (B-axis) with clamping in position Continuously positioning NC- swivel milling head with integrated motor spindle for 4/5 axes positioning and simultaneous machining. Swivel speed: 50 rpm Swivel range: ±12Clamping System HSK-A 100Spindle taper HSK-A 100Speed range 20 -12000 rpmTorque (40% DC) 288 NmTorque (100% DC) 187 NmDrive power (40% DC) 44 kWDrive power (100%  ...

Perfectly working Zumex Speed S+ with conveyor belt to remove the orange pulp. Spare parts included. Viewing by appointment Auction-ID: A1-40237-57

For lithium batteries from 82-410Ah REMA Battery Connector 400V plug Auction-ID: A1-45449-3587

For lithium batteries from 82-410Ah REMA Battery Connector 220V plug Auction-ID: A1-45449-3590