127,426 used machines on RESALE, but how to find them? Machine Search
Engine serial nr.: NYJ00480, Generator set serial nr.: K7F00641, Generator serial nr.: 74B0080; Gross weight [kg]: 16080; Engine: Caterpillar 3516B; Accessories: Control Panel
x-travel: 6000 mm y-travel: 2000 mm z-travel: 3000 mm Control: heidenhain TNC 415 total power requirement: 34 kW weight of the machine ca.: 31 t dimensions of the machine ca.: 7000 mm m Stocknumber 1110055 Type of machine CNC Floortype milling machine Make ZAYER Type KCU6000 Build in 1992 Type of control Heidenhain TNC 415 X-stroke (mm) 6.000 Y-stroke (mm) 2.000 Z-stroke (mm) 3.000 Speeds (Rpm) 20 - 1.800 Admission in spindlehead BT50 Feeds X (mm/R) 5 - 5000 mm/min Feeds Y (mm/R) 5- 5000 mm/min. Feeds Z (mm/R) 5- 5000 mm/min. Rapid feeds 10.000 mm/min. Total Power (KW) 34 Lenght (mm) 11.000 Width (mm) 2.500 Height (mm) 7.000 Weight 31.000 Kg Additional information Juaristi MG6 turntable: 1500 x 1200 mm Cooling system: 2.5 Bar Tool cooling: 15 Bar The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
; Gross weight [kg]: 2035; Engine: Hyundai P086TI-1; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger, Including : sockets 125A - 63A - 32A - 16A; Water Tank Volume [l]: 185
; Gross weight [kg]: 4600; Engine: Hyundai DP158LC; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 775
; Gross weight [kg]: 6185; Engine: Hyundai DP222LC; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 1090
; Gross weight [kg]: 2364; Engine: Hyundai P086TI; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger, Including : sockets 125A - 63A - 32A - 16A; Water Tank Volume [l]: 224
Machine name: Injection moulding machine used Manufacturer: Ferromatik Milacron (Klöcker) Type: FX50 R 35 Year of Make: 1991 Operating hours: 2000 h Drive motor:15 kW Dimensions: L 4300 x W 1400 x H 2200 mm Curb weight: 3400 kg Tech. Documentation: Yes Remark: General data: Dry running rate: 40 min, Pump drive: 15 KW, Total connected load: 25.7, Oil tank capacity: 180 L Injection unit: Screw diameter: 35 mm, Injection pressure: 1730 bar, Stroke: 116 cm3, Screw stroke: 120 mm, Moulded part weight max.: 99 g, Injection flow max.: 505 g/s, Injection capacity calcane: 15 KW, Plasticising flow: 29 g/s, Screw length: 22 LID, Screw speed max.: 430 min, Screw torque max.: 360 Nm, Installed heating capacity: 10.7 kW, Number of heating zones: 5, Nozzle press force: 65 kN Clamping unit: Clamping force: 500 kN, Tool opening distance: 350 mm, Tool installation height min.: 200 mm, Plate spa ...
Presona LP 85 VH2 cross-tying baler, built in 2018 Specifications: Manufacturer: Presona Sweden Type LP 85 VH2 Year of manufacture 2018 Drive power 2 x 45 kW Operating hours 40,350 Effective operating hours approx. 22,000 Press force pre-press 28 t Press force main press 85 t Insertion shaft 1500 x 1100 mm Bale dimensions 750 x 1100 mm Bale weight 450 - 650 kg Theoretical volume: 1200 cbm/h Throughput at 30-100 kg/cbm: 13-30 t/h Tying 5-fold vertical, 3-fold horizontal Oil tank capacity 2000 L Transport dimensions press 10400 x 2400 x 2800 mm (LxWxH) Weight approx. 27000 kg The press was dismantled from ongoing operations. A spare parts package is included. The technical documentation is available. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided or any errors. The offer is subje ...
Key data: 132
Used Deutz A12L614 diesel engine Year of construction : 1955 Air-cooled 12 cylinders 180 hp Clutch power : 132,39 KW Engine has run after major revision only very few hours !
saw blade diameter: 1250 mm cutting diameter: 380 mm cutting range: 480x320 mm motor speeds:: 3000 U/min feed speeds: 1000 mm/min main drive motor: 112 kW chip conveyor: cutting speed: 10-265 m/min total power requirement: 125 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Box washer, Fabr. Drill, type: R 20, in VA, with hinge belt transport chain, pump, 2 VA screens, control cabinet, YOC 1989 Box washer, Fabr. Klann, type: 600, with large pump, with screening box with 3 VA screens, YOC 1988, dismantled Box washer, Fabr. Kettner/Sotec, Type: WAH 18, 1,800 Ka/h, with control cabinet, YOC 1990 Prices on request
new accuhead, brand Kingswerk (similar to Kautex). Immediately available from stock
Styrofoam shredder MAXI XL 1400 x 560mm MAXI 1400 x 600mm JUMBO 1800 x 800mm Insertion opening: L x W Polystyrene shredder MAXI XL: 1400mm x 560mm Polystyrene shredder MAXI: 1400mm x 600mm Polystyrene shredder JUMBO : 800mm x 800mm Dimensions: L x W x H (dimensions without blower) Polystyrene shredder MAXI XL: 2.4m x 0.9m x 1.6m Polystyrene shredder MAXI: 1.9m x 0.8m x 1.8m Polystyrene shredder JUMBO: 2.4m x 1.1m x 1.8m Motor power/connection/power conveying fan: Pre-shredder / conveyor blower Polystyrene shredder MAXI XL: 5.5 kW | Blower 2.2 kW Polystyrene shredder MAXI: 6.2 kW (with built-in screw under the pre-crusher) | Blower 2.2 kW Polystyrene shredder JUMBO 11.2 kW (with built-in screw under the pre-crusher) Conveyor blower 5.5 kW Throughput (EPS) Polystyrene shredder MAXI XL: 8-10 m3/h Polystyrene shredder MAXI: 25-30 m3/h Styrofoam ...
Polystyrene compressor Styropactor MAXI | Shredder press for Polystyrene EPS Compressor, combination of shredder and press for polystyrene EPS MAXI Commodity number: 42055 Throughput: Measured with fish crates of 25 KG/M3 Material space weight EPS: 70-90 kg/h Throughput measured in fish crates with lid (650 grams per piece and about 800x400x220mm): 100-120 Connection: 7.5kW, 3-phase 400V/50Hz 480V/60Hz Insertion opening: 600×1000 mm Length: 3180 mm Height: 1600 mm Width: 870 mm MAXI PLUS Commodity number: 42060 Throughput: Measured with fish crates of 25 KG/M3 Material space weight EPS: 110-130 kg/h Throughput measured in fish crates with lid (650 grams per piece and about 800x400x220mm): 170-200 boxes/h Connection: 11kW, 3-phase 400V/50Hz, 480V/60Hz Insertion opening: 600×1000 mm Length: 3680 mm Height: 1600 mm Width: 870 mm Wet boxes: YES Stainless stee ...
cross-section width:: 100 mm cross-section heigth:: 40 mm feed:: 2 - 999.999,9 mm Condition: new, Specification: Impact knife cutting machine CC-600/40 for hoses and profiles - contact length: 600 mm - product diameter: 40 mm - belt width: 100 mm - Tractive force: 400 N to 800 N - Drive: 2 drives upper and lower belt - Conveyor belt speed: 100 m/min - Drive feed, cutting motor: Servo drives - Cutting capacity with blade max.: 4,000 1/min - Connected load: 3.5 kW - Dimensions L/H/B: 1,900 x 1,650 x 960 mm - Weight approx.: 580 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
2 cloth press 1,0 m cloth width capacity: up to max. 4 t with top fruit
Axtor 6010 Category: Universal Shredder Manufacturer: Komptech Serial / reference number: 249037 Hours: 4 620 Power: 433kW/589 hp Weight: approx. 25 000 kg Emission class: Tier 4 Final / Stage IV Equipment and description: Overbelt magnet Remote control Advance device Shredder, chipper blades or cantilever chairs Material: good for green waste, bark, logs, splinters and wood waste 2 drum speeds 460 / 810 rpm (modification for cantilever chairs) Drum width 1,543 mm / Drum diameter 1,108 mm / 32 tools, blades Filling height: 2,800 mm / Screen baskets: 60×60, 80×80, 100×100, 125×125 etc. possible / other sizes can be produced Throughput depending on material and operator between 100 and 300 m3/h / Feed hopper over 4 m long / noise emission: 122 dB (A) Transport Dimensions: Length: 11,700mm; Height: 3,750mm; Width: 2,500mm; Towing eye: 50mm
Many thanks for your interest on our second hand machines, please find follow our offer: Kadema enrober with Original wooden cooling tunnel manufacturer: Kadema; Johannes Kegel Dresden Type: Juwel 305 enrober electrical: 400 VAC / 3 Ph Year of manufacturing: 1930 work width: 305 mm different: With origin wooden cooling tunnel, approx. 8m extendable mass container absolutely in original condition ! We offer this machine in 'as is' condition, without warranty EXW Hess. Lichtenau, (EXW)unpacked
Many thanks for your interest on our second hand machines, please find follow our offer: Kadema enrober antique manufacturer: Kadema; Johannes Kegel Dresden Type: Juwel 620 enrober electrical: 400 VAC / 3 Ph Year of manufacturing: maybe between 1930 - 1940 work width: 620 mm different: with wooden cooling tunnel, approx. 8m fixed mass container We offer this machine in 'as is' condition, without warranty EXW Hess. Lichtenau, unpacked
STEAM BOILER - GAS FIRED MAKE : AMF / CALLENS YOC : 10/1995 CAPACITY : 2.240.000 kcal 2605 kw Pressure : 12,24 kg/cm2 12 bar • With a water supply temperature of 100°C, the steam production should be about 4 tons/hour
The gate valve / shut-off valve is a fitting that is used to fully open or close the entire flow cross-section of a pipe. An unused shut-off valve from plant closure, reserve material is offered! Manufacturer KSB Type BOA 65 YOC 2013 Multiple available, also other sizes e.B. BOA 80 If you are interested, please ask!
Used blow moulding machine made by KRONES model Contiform S18. New 2004. It has 18 blow moulding stations. The maximum blow moulding speed is 24,000 bottles per hour for the 2.0 l format and 28,000 bottles per hour for the 1.5 l format. In February 2024, the machine was upgraded to support the PCO 2622 thread. The blow moulding machine has an integrated control system with visualisation in Polish, English and German. A complete set of documentation is included with the blow moulding machine. The blow moulding machine includes: an automatic glycol cooler, an automatic preform feeder, an automatic preform basket tipper and a bottle ejector mounted on an air transport conveyor.
Heating elements used in Kisters ZVT and ZEVA shrinktunnels. Various quantities and lengths (600, 700 and 1000 mm) and types (straight, bent, with and without wires) available: 240, 290 and 347 Volts, 2150, 3100 and 3500 Watts.
Printing Width: 1250 mm // Web Width: 1300 mm
Metal Circular Saw Cold Circular Saw Manufacturer Kasto Type GKS400P YOC 1998 Saw blade 400mm coming from below automatic hydraulic vice for material expansion Top condition, ready for immediate use.
Key data: 6100 kg, 970 mm
Refurbished Beche KGH 8.0 forge hammer (built in 1980) The hammer was completely overhauled in Germany. The RAM (Schabotte) is from 2013. Control System: 2025 Description of the modernisation works: Hydraulic drive - Completely disassembled in 2024, cleaned, control valves replaced New control system - Siemens S7-1500F PLC control system with touch panel RAM (U-frame) - Contact surface ground - Insert adjusted - New wedge manufactured and hammered in Test run - Hammer was assembled in 2024 and tested in 2025 Technical description: Working capacity: 80 kJ The height max. 600 mm (without swallows) The height min. 200 mm (without dovetails) Bear depth: 810 mm Bear weight: 6100 kg Scabot weight: 105000 kg Total weight: 130700 kg Total height: 7.3 m above floor level Scope of delivery: •Hammer •Documentation The Modernisationword were well ...
material dimensions max. round: Ø 380 mm max. square: 380 x 380 mm segment length with single stroke: 10 - 510 mm with multi stroke: max. 4590 mm dimensions LxWxH: 3100 x 2200 x 1850 mm weight: 3.100 kg
Corona pretreatment plant of AFS AVE-120D-KER3/1200 with generator G-30 S-111 (3000 W) For sale is a corona pretreatment plant from the renowned company AFS, type AVE-120D-KER3/1200, including generator G-30 S-111 with an output of 3,000 watts. The system is used for surface pretreatment of films, papers and other non-conductive substrates to ensure optimal adhesion of printing inks, varnishes or adhesives. Technical data & equipment: Manufacturer: AFS Type: AVE-120D-KER3/1200 Generator: G-30 S-111 Power: 3,000 W Working width: approx. 1,220 mm Treatment: Corona (electrical discharge) Application: Pretreatment of plastic films, composite films and similar materials Condition: Used, functional and in good technical condition Operating hours: approx. 50 Particularities: Compact, robust design for continuous industrial operation Low maintenance ...
Part Number: 7805 SPECIFICATIONS - track width 340mm - shaft width 340mm - blade hole diameter 80mm - 350mm discs on the upper shaft - mounted discs on the lower shaft 300mm - max cutting height 200mm - min length of the processed material 700mm –in advance - 2 rows of flingers - smooth, slippery, pressure shaft - Flingers - 2 slip shafts, smooth, pressure shafts - shaft with saws - 3 pressure rollers, smooth – from below -caterpillar - shaft with saws -caterpillar - infinitely variable feed speed regulation - main motors 2x approx. 55kW - 3kW feed motor - Electric body up/down lifting - manual adjustment of shafts with saws - central lubrication - Extraction port diameter 2x200mm - dimensions l/w/h 2700x1800x2150mm - weight about 5000kg ADVANTAGES – German production – twin-shaft – 2x55kW motor – used multi-saw, very goo ...
• Year 2022 (like new) • Offering up to 800 amps of gouging power with 50 % dutycycle, • the KempGouge ARC 800 is a heavy duty power source package that is designed for all types of carbon arc gouging. • KempGouge can be used with the majority of metals, such as steel, stainless steel, cast iron, nickel, copper, magnesium, andaluminum. • KempGouge lets you open roots or faulty welds and cracks, prepare welding grooves, cut metals, make holes and cleancasts, and remove excess metal. • The characteristics curve controlling the KempGouge’s operating parameters has been designed specifically for carbon arc gouging, so its gouging properties are optimal. • The noise levels of KempGouge have also been kept very low. • FAST AND EFFECTIVE Way to remove defects, backgouge the root, cut metal and pierce holes • EASY WAY To move the equipment and adjust t ...
Closing heads Krones for aluminium screw caps suitable for several types of closing machines like Alcoa, Adelski, Arol, etc. tested and ready to work
Reference ID PP-53973 Category Bag Machines Manufacturer - Model BL66 Year Built 2003 Color 4 Impression- Working Hours - Speed-- Max. Size - Min. Size - Condition Good Location Europe Availability Immediately Machine Description a complete multiwall paper sack line Tuber: 3 unwinders Perforating unit Printing unit with 4 colors Cross pasting unit for up to 3 plies Digital lengthwise injectors for 3 plies - Maximum repeat: 1300 mm, Minimum repeat: 380 mm, Maximum width: 650 mm, Minimum width: 200 mm Transystem Bottomer: Automatic rotary feeder Bottom patch unit each side Double valve unit Maximum depth: 170 mm, Minimum depth: 80 mm, Minimum distance between centers: 250 mm, - Maximum distance between centers: 600 mm (with a maximum depth of 150 mm) A single valve carriage that can hold 2 sheets. Palletizer
Kroll M 150 Mobile Warm Air Generator Application Heating of halls, tents and construction sites Frost-free keeping in horticultural businesses or warehouses of all kinds Fast drying of new buildings Additional heating in the cold season Fuel: Heating oil EL Nominal heat output: 135 kW Nominal heat load: 150 kW Oil throughput: 12.7 kg/h Air volume flow: 7,300 m³/h Electrical connection: 220 V / 6.1 A Power consumption: 1.38 kW Degree of protection>: IP 44 Metrics: Length: 2600 mm Width: 900 mm Height: 1300 mm Weight: 270 kg More items - new and used - can be found in our shop! International shipping costs on request!
USED KRAUSS MAFFEI HZ 630 PH CENTRIFUGE REF.: C6486 General characteristics: Manufactured by KRAUSS MAFFEI Model HZ 630 Ph Technical characteristics: Basket diameter 630 mm Max. rotational speed 2400 rpm
RECONDITIONED KRAUSS MAFFEI KM 125 ATEX CENTRIFUGE REF.: C3553 Vertical basket bottom discharge reconditioned centrifuge with scraper on inertia plate with 4 dampers discs type ZPVL 25-45.6 Type KM 125 manufactured by KRAUSS MAFFEI. AISI 316L wetted parts. General characteristics: Manufactured by KRAUSS MAFFEI Model KM 125 Type Vertical basket bottom discharge centrifuge with scraper Material Stainless steel 316L Weight 6400 kg Technical characteristics: Download Por el fondo con rascador Basket diameter 1.250 mm Height basket 650 mm Max. load 650 kg Useful load 500 dm3 Max. rotational speed 900 rpm Engine 37 kW - 50 cv
USED KRAUSS MAFFEI HZ 63 SI CENTRIFUGE REF#: C6483 General characteristics: Manufactured by KRAUSS MAFFEI Model HZ 63 Yes Caractéristiques techniques : Densité admissible du produit : 1250 kg/m3. Température du produit : 50 ºC Technical characteristics: Basket diameter 630 mm Max. rotational speed 2400 rpm
Closed metal energy chain, S1250.171-RM-300-St-4000, Kabelschlepp, mint condition Special price ! If you have a VAT number, we will gladly issue an invoice without VAT. As good as new! The part comes from a spare parts warehouse at a manufacturing plant, has never been used, is new and has only very minor signs of storage. Metal energy chain, energy guide, S1250.171-RM-300-St-4000, cable carrier, as good as new, Closed, heavy-duty design Includes 2 connecting parts Total length measured approx. 4300 mm, outer width 195 mm, web width 171 mm, 32 links, 6 months warranty We give you 6 months warranty for these goods from the date of invoice. In case of any defect, which is not the fault of the buyer, the goods can be returned. We will refund the buyer only the product price paid to us. Updating in case of digital components is excluded. Also excluded is liability for dire ...
Palletizer KRONES PRESS UNI, production year 2007 Along with the conveyors presented in the layout. • Palletizer for collective packages, capacity: approx. 50 pallets / h for specific palletizing formats, • Top loading, packs served in 2 tracks, • Pallet magazine, • A feeder for cardboard pads with a magazine for cardboard pads, • Control cabinet based on Siemens S7 control, • A platform for the operator in accordance with the dimensions presented in the layout, • Operator Panel, Packs and pallet conveyors in accordance with the presented layout 1. Empty pallets infeed conveyors 2. Packs conveyors
2.The main structure and performance of the machine tool: This machine tool is designed and manufactured using the latest technology, ensuring its strength, rigidity, and safety. Its simple and elegant appearance and exquisite workmanship demonstrate meticulous machining and component assembly. The machine utilizes a single, high-quality welded steel structure, resulting in a thick, rigid frame. The machine surface is sprayed with imported rust-resistant primer and topcoat, ensuring it remains as good as new for a long time. The frame and upper working slide are machined using imported large-scale CNC floor-type boring and milling machines, ensuring the required positioning accuracy of all mounting surfaces. This machine tool primarily consists of a frame, upper slide, backgauge system, slide, synchronous control device, mold, hydraulic system, and control system. 2.1 Frame: This pa ...
The all-electric servo bending machine is one of the products with independent intellectual property rights developed by our company. Special high-load screw and guide rail structure, imported bearing installation, high load-bearing capacity, high positioning accuracy, long life, machine tool rigidity, precision retention, and reliability are close to perfection. By introducing advanced design concepts and scientific design methods, the shortcomings that traditional designs cannot avoid have been solved. This bending machine is fast and simple to program, can realize concurrent linkage of multiple axes, fast feed positioning, and significantly improves the efficiency, accuracy and consistency of bending, which is far superior to traditional hydraulic bending machines, and does not require the use of hydraulic oil, is environmentally friendly and pollution-free. Compared with traditional ...
Progressing cavity pump for separator feeding, original pump housing available - was built into a special pump housing, functional due to project change dismantled: Flow rate: approx. 20 m³/h Drive power: 7.5 kW
maximum number of results exceeded
please refine your search
