k t used for sale

Flywheel size: SAE4, 2 units available; Gross weight [kg]: 87; Accessories: Including: 3 current transformers

Construction & Dimensions Floor space: Hall 15.35 m x 24.49 m plus canopy (depth 3.82 m). Roof pitch: The gable roof has an inclination of 15° (canopy 10°). Weight estimate: The steel structure is estimated to be approx. 18 to 22 tons (pure steel weight without cladding). This serves as the first basis for your logistics planning. Base & façade The hall was originally mounted on a 40 cm high clinker brick base. Since this is omitted during dismantling, a corresponding plinth (e.g. made of precast concrete elements or masonry) would have to be prepared on site for the reuse of the original wall panels before reassembly in order to maintain the connection heights of the façade. Foundation & Clearance Areas Foundation planning: The hall was founded on strip foundations with a 15 cm base slab. Since the soil conditions at your new location can vary, the foundation statics s ...

SPECIFICATIONS: Sweeping width mm: 600 Complete with: 01 Longitudinal brush 01 Side brush 01 Battery charger As good as new

Clipping machine Technopack KDCVT 200 Type: KDCVT 200 Dimensions: 100x60x190cm Maximum closing diameter: 120mm Delivery time: 30 working days after advanced payment

; Gross weight [kg]: 818; Engine: Perkins 1103A-33G1; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger, Including: 125 liter fuel tank capacity; Water Tank Volume [l]: 125

We offer a paternoster LTG-TowerMax P 13.8-300-46-210-6500 with a completely new StoreControl P control system, which has been modernized by us Exterior Dimensions: Overall height 6,500 mm Overall width 3,670 mm Installation depth 1,560 mm 46 carriers with a payload of 300 kg each in clear usable dimensions: H = 210 mm W = 3,050 mm T = 520 mm Chain jump 254 mm 23 galvanized intermediate floors for 150 kg payload each Total payload up to 13,760 kg Side table in 1000 mm above OKFF with NiRo worktop, 300 mm deep, manually operated lifting door Colour scheme grey/dark grey Motor power drive 1 x 5.5 kW / 400 Volt subject to errors and technical changes, surfaces cleaned, signs of wear and minor deformations possible, Delivery & installation currently mainly in D, A and other neighboring countries

; Gross weight [kg]: 7000; Engine: Volvo TWD1683GE-SV; Accessories: Tanker, Battery, Control Panel, Stahldach, Stage V Generator, Stage V Aggregaat, Stage 5 Generator, Stage 5 Genset, Stage V Gen set, Stage V Generator set, EU Stage V Generator, StageV, Including : coolant heater and battery charger; Water Tank Volume [l]: 985

; Gross weight [kg]: 3840; Engine: Volvo TAD882GE-SV; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 1800

; Power [PS]: 489; Gross weight [kg]: 4000; Engine: Volvo TAD1344GE; Accessories: Tanker, Battery, Control Panel, Stahldach, Including : coolant heater and battery charger; Water Tank Volume [l]: 515

; Gross weight [kg]: 3700; Engine: Volvo TAD1343GE; Accessories: Tanker, Battery, Control Panel, Including : coolant heater and battery charger; Water Tank Volume [l]: 576

Electrode welding machine Manufacturer Kemppi Type TYLARC453 Power 450 amps at 35% ED, 345 amps at 60% ED 265 amps at 100% ED Power 20kw, 21kva Power connection 400 Volt Weight approx. 250kg Machine ready for demonstration under power. Shipping on Euro pallet possible. Price is net plus 19% VAT Please note our "Legal Information" with further information

Electrode welding machine Manufacturer Kemppi Type TYLARC653 Power 650 amps at 35% ED, 545 amps at 60% ED 465 amps at 100% ED Power connection 400 Volt Weight approx. 300kg Machine ready for demonstration under power. Shipping on Euro pallet possible.

Catalog number 6726 TECHNICAL DATA - 280x300mm loading hopper inlet - outlet for shredded wood fi 310mm - rotor working width 340mm - 22kW main engine - number of knives 6 pcs - dimensions length / width / height 1300x1150x1680mm - weight 720 kg ADVANTAGES - very good condition - used chipper Net price: PLN 19900 Net price: EUR 4422 Net price, calculated at the rate of 4.50 PLN / EUR (with greater fluctuations in the rate, the price may change)

Available in stock 1 x Used Boll & Kirch Duplex Filter and 1 x Used Boll & Kirch Lub. Oil Automatic Filter. The equipment was used in a HFO power plant. The equipment is used but is in good working conditions. Max all working pressure: 10 bar Max all working temperature: 80ºC

working width: 4 m Number of gangs: . 0 Number of folders: 2 0 Number of rollers: 1 St. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

; Gross weight [kg]: 1005; Engine: Kubota V3300-TE2BG2; Accessories: Tanker, Battery, Control Panel, Stahldach; Water Tank Volume [l]: 140

4 column truck / bus lift WITH INTEGRATED LIGHTS Lift is already dismantled, ready to load on truck. We can organize it transport inside EU. We can organize it 4-column: yes width between the columns 335cm length lanes 800cm

DM 750 x 60 x 304,8mm unused in original box. Specification: CS25A 802 JJ6 VK1 For stainless material. Piston rods were ground with it.

SHREDDER KOMPTECH TERMINATOR 5000 E incl. control cabinet

TMP VORONEZH KA2536 crank press was built in 1979 in the USSR by the Voronezh Mechanical Press Plant (Воронежский механический завод). The offered machine is perfect for many industries, especially those which require high press force and high repeatability of produced parts. This is because it enables even the most demanding metal forming processes to be performed, i.e. stamping of structural components, forming of parts, hot and cold forging, deep drawing operations and the production of parts with a large surface area. All of these machining processes are performed with a high press force of 400 tonnes and can be carried out continuously, increasing production efficiency and reducing downtime to a minimum. The crank mechanism used ensures uniform force transfer, which translates into precise slider feed and repeatability of each cycle. This solution is part ...

width: 1000 mm depth: 600 mm height: 2150 mm weight: . kg Tool cabinet for Sk50 recordings without roller shutter non-binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About usMore than 400 of our own machines in the warehouseMore than 12,000 m² of storage space, crane capacity 70 tMore than 1000 items Accessories for your workshopYou want to sell machines, production lines or your company,then contact us. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 45 , 33000 , 1250

Brand MARTIN Type T72A Comfort Control panel eye level integrated in the suction supports Saw blade height adjustment: Electric with digital display in the screen Saw blade tilt: Electric with digital display in the screen Parallel stop: NC control with digital display in the screen Parallelogramtic: Aluminium miter table, -46° to 46° digital display, angle-length calculation table Length stop: Aluminium 2,200 mm, extendable up to 3,200 mm with 2 punch stops and digital display Main saw: ø450 mm, cutting height: 170 mm, saw swivelling: 0° - 46° Speed control: 2000/2750/4000/5500 rpm Motor: 5.5 KW Scorer: ø120 mm, 3-axis electric adjustment Motor: 0.75 KW Trolley: 3,300 mm Cutting width: 1,250 mm Suction: Top: ø80 mm, Bottom: ø120 mm weight: 1.600 KG Condition: still to be cleaned, tested, etc.

x-travel: 970 mm y-travel: 420 mm z-travel: 430 mm Control: Heidenhain TNC 135 number of speeds: 12 speeds: 31,5-1400 U/min feed range lengthways and crosswise: 8-2000 mm/min feed range - vertical: 4-1000 mm/min rapid traverse longitudinal and cross: 4 m/min rapid traverse Z-axis: 2 m/min weight of the machine ca.: ca. 3,8 t dimensions: ca. 3050x2350x2320 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Cooling water pump, centrifugal pump, water pump, coolant pump, drilling water pump, submersible pump -Manufacturer: Kracht -Type: TK21/150 -Power: 0.1 kW -Speed: 2800 rpm -Connection: 220/380 volts -Dimensions: 160/240/H340 mm -Weight: 10 kg

BVM Compacta Konti 5015 MY 2005 BVM SC 4030 SD Bj 2005 BVM TB 400 Bj 2007 BVM inlet conveyors

Make : TREPKO Model : 222 KPS Year Of Manufacture : 2004 Machine Dimensions : 1,35 x 1,55x 3,32 metres with conveyor 3,2 meters Product : Butter / Margarine/soft products Cup Dimensions : 115 mm x 75mm Volume : Min 180ml | Max : 500ml Cleaning : CIP Hours : 688,45 Plastic Cup With Aluminium Lid and Cover Cap Condition : Good

Nominal force: 2500 tons Slider stroke: 600 mm Slide strokes per min: 11 Distance between table and slider: 1500 mm Capacity of the main drive: 220 kW Table size: 2000x4500 mm Machine dimensions: 5910x8700x10355

Key data: 2613 , 3194 , 6300

2613 KW KKK condensing steam turbine Twin AFA46 GT6 from 2004 in good condition, used for sale. Manafacture: KKK Model: AFA 46 GT6 Type: Steam Condensation Serial Number: 4.746.137 Power [KW]: 2.613 Pressure inlet [bar]: 29 Temperature inlet [°C] 360 Pressure outlet [bar]: -0.8 Year of construction: 2004 Weight [kg]: – Dimensions LxWxH [cm]: – More information here: stromerzeuger-discount.de/angebote/dampfturbinen/2610-kw-kkk-twin-afa4 6-gt6/

Krones Topmatic Heads: 51-8-8-130 right - left Capacity: 65,000 bph Ma-No. K071-438 Krones Topmatic Heads: 51-8-8-130 right - left Capacity: 65,000 BPH Ma-No. K071-438

refrigeration system with a fan Year of construction :1990 Power : 1,1kW Voltage : 220/380 V 50Hz Amperage : 6.6 /5.8 V For further information, please refer to the type plate

Refrigeration system with a fan Year of manufacture : 1993 Power : 3,2/2,0 kW Voltage : 380 V 50Hz Amperage : 6.4 / 3.7A Capacity : 41,5 dm³

Stick electrodes 4.0 x 450 -Type: Phoenix K 50 -Price: per package -Number: 5 packages available -Weight per package: 5.8 kg

Ex signal isolator, isolated barrier -K series -Product number: 14493S -Explosion proof -Number: 5x available -Price: per piece -Dimensions: 95/70/H18 mm -Weight: 0.1 kg

Conveyor belt, Fabr. Zeva, rod tape 350 mm

Conveyor belts, Fabr. Schmidt-Lünen, belt width 1050 mm, straight line total approx. 23 m1 curve 90 drive stations + motors + electr. Switchboard

Conveyor belt, mobile, stainless steel version

Triplex Plunger Pump Unit KD825 URACA for Press Drive consisting of: Pump KD825 URACA Pressure Lubrication unit Water-Oil cooler Reduction bevel helical gear box (angular design) with couplings Base frame open type Discharge ball resonator (pulsation damper) Pressure safety valve, set pressure 360 bar Induction electric motor Process medium: water-oil emulsion Discharge pressure 325/320 bar Capacity 1,330 l/min Pump speed 340 min-1

Stick electrodes 3.2 x 350 -Type: Phoenix K 50 -Price: per package -Number: 6 packages available -Weight per package: 4.5 kg

Stick electrodes 3.2 x 350 -Type: Phoenix SH copper 1K -Price: per package -Number: 5 packages available -Weight per package: 4.4 kg

CREEL KNIFE - CUTTING CREEL FOR DICE CUTTER MACHINE TREIF - USED 1 set. GATE KNIFE D = 20 mm for cube cutter TREIF FELIX AND FOR TREIF DERBY Art.Nr. 51823 1 set CREEL KNIFE D = 26 mm for cube cutter TREIF FELIX CE Art.Nr. 51818 Request a Quote iNTER-WiBA Sp.J. Ul. Krakowska 263 PL 43-305 Bielsko-Biała VAT number: PL547-17-47-669 Phone: 0048/33 812 58 60 fax. 0048/33 812 58 36 abc.inter-wiba.com.pl infointer-wiba.com.pl

Sheet metal clamp, sheet metal claw, beam clamp, beam claw, sheet metal gripper, material gripper, material gripper -Sheet metal claws -Span width: 0 to 40 mm -Load capacity: 3200 kg -Number: 1x terminals available -Price: per piece -Weight: 21 kg/piece

Beam claw, sheet metal clamp, sheet metal claw, beam clamp, sheet metal gripper, material gripper, material gripper -Sheet metal claws -Span width: 0 to 30 mm -Load capacity: 2500 kg -Number: 1x terminals available -Price: per piece -Weight: 15 kg

Beam claw, sheet metal clamp, sheet metal claw, beam clamp, sheet metal gripper, material gripper, material gripper -Sheet metal claws -Span: 0 to 40 mm -Load capacity: 3500 kg -Number: 1x terminal available -Weight: 30 kg

Sheet metal clamp, sheet metal claw, beam clamp, beam claw, sheet metal gripper, material gripper, material gripper -Sheet metal claws -Span width: 0 to 38 mm -Load capacity: 2500 kg -Number: 3x terminals available -Price: per piece -Weight: 15 kg

echnical characteristics Nominal force, mc 1600 Not reach the slide to BDC, mm 12 Progress in the slide, mm 400 The frequency of continuous strokes, min-1 16 The highest frequency of single strokes, min-1 12 Closed height mm 870 Adjusting the closed height 220 mm Size slider, mm left to right 1600 front to back 1600 Dimensions plate, mm left to right 1600 front to back 1600 Power of main drive, kW 110 Dimensions, mm left to right 4670 aft 4670 height above floor level 8110 W 154 000kg

Sheet metal clamp, sheet metal claw, beam clamp, beam claw, sheet metal gripper, material gripper, material gripper -Sheet metal claws -Span: 0 to 60 mm -Load capacity: 5000 kg -Number: 2x terminals available -Price: per piece -Weight: 49 kg

Sheet metal clamp, sheet metal claw, beam clamp, beam claw, sheet metal gripper, material gripper, material gripper -Sheet metal claws -Span: 35 to 70 mm -Load capacity: 5000 kg -Number: 3x terminals available -Price: per piece -Weight: 39 kg/piece

Gear motor, electric motor -Speed: 8.5 rpm -Power: approx. 0.18 kW -Construction: B3 -Diameter shaft: Ø 40 mm -Protection class: -Dimensions: 565/255/H255 mm -Weight: 44 kg