juice press used for sale

ZTS KOSICE LE 160 C eccentric press was built in 1988 in Czechoslovakia by Závody Tažkého Strojárstva n.p. Košice. The machine is in very good technical condition and has been regularly maintained throughout its service life. All control solenoid valves were replaced in February 2023. ZTS KOSICE LE 160C is an excellent choice for a wide range of workpiece machining, i.e. punching, cutting and stamping. All of these machining processes are performed with a high press force of 160 tonnes, which, combined with a rigid design, enables the production of parts with high repeatability and excellent precision. The ZTS LE 160 C eccentric press weighs 10150 kg. Technical specifications of the ZTS KOSICE LE 160 C press - maximum press force: 160 t (1600 kN) - maximum number of slider strokes: 50/min - number of slider strokes in single mode: 30/min - maximum slider stroke: 120 mm -  ...

Frame press Hess hydraulic Type: HYDRO-LUX Crimping dimension approx. L 3550 m x W 2250 mm Connected load 380 V / 50 Hz 2.6kw Hydraulic Pump Machine dimensions Length 6600 mm x Width 1600 mm x Height 2770 mm 0 - 8 bar pneumatic Optoelectronic measurement query. The window scantlings are placed in the feed channel so that the photoelectric sensor can measure whether the pressure beams and press corners need to be opened or closed. If the light beam of the probe hits the window scantlings, the machine receives the command to drive up in width and height until the working dimension is reached. Workflow: Automatic dimensional adjustment loose insertion Automatic pressing process loose presentation remove Automatic dimensional adjustment Program selection options in the control system: 1. Automatic measurement adjustment via optoelectronic measurement query with a ...

Inv. Num. : 5831 Type: PKnT 160 Producer: ERFURT Created: 1987 Parameters: Compressive force: 160 t Maximum stroke rate top table: 15 1/min Total power requirement: 21 kW Ram stroke: 265-425 mm Adjusting the plunger: 130 mm

SPECIFICATIONS: Membrane press for gluing doors, curves and other wooden elements Dimensions mm: 2400 x 1120 Heating by electrical resistance Complete with decompressor, timer and tarpaulins

Key data: 200 t, 500 mm, 200 mm

(1982) 200t Lauffer Hydraulic Press High-Speed Hydraulic Press with Advanced Shock Absorption This Lauffer hydraulic press is a high-performance machine designed for speed and precision, capable of 2,000 kN of pressing force. Its high-speed designation is backed by a rapid descent speed of 330 mm/sec and a sophisticated 8-fold flat guidance system to maintain ram alignment even under heavy or off-center loads. Technical Details Machine Type: Hydraulic Press Manufacturer: Lauffer Model: RPS 200 Year of Manufacture: 1982 Nominal Force: 200t Max. Return Force: 225 kN Max. Ram Stroke: 200 mm Shut Height: 500 mm Ram Guidance: 8-fold flat guidance Table & Ram Surface Area (W x D): 800 mm x 630 mm Table Hole Diameter: 204 mm Clearance Between Uprights (Front / Side): 840 mm / 320 mm Operating Speeds: Rapid Descent: 0 – 330 mm/sec (steplessly adjustable) Pre ...

Key data: 250 t, 500 mm

(2018) 250t Hidroliksan Hydraulic Press Hydraulic Press with Integrated Die Cushion for Deep Drawing This 2018 hydraulic double-column press is a heavy-duty production unit designed for versatility, featuring a robust 250-ton capacity and high-quality Rexroth and SICK components. With its 100-ton integrated die cushion and generous 500 mm stroke, it is exceptionally well-suited for complex deep drawing and forming operations that require precise pressure control. Technical Details ‍ Machine Type: Hydraulic Double-Column Press Manufacturer: Hidroliksan Model: H-TYPE Nominal Force: 250t Return Force: 50t Stroke Length: 500 mm Speeds: Approach: 160 mm/sec Pressing: 5 – 15 mm/sec Return: 190 mm/sec Working Surfaces: Ram Plate: 1,000 x 800 mm Table Plate: 1,000 x 800 x 100 mm Components: Pump: REXROTH (71cc – 103 L/min) Motor: 22 kW (30 hp), 1,500 rpm ...

Standard accessories: - 10m high pressure hose DN10, kink protection on both sides - HDP350 high-pressure gun with quick coupling and swivel joint in the input - Double jet tube with nozzle 065 and low pressure nozzle Optional (additional cost): - Hose reel - 30 m high pressure hose The images contain additional options. Shipping possible. Errors and prior sale excepted. We refer to our terms and conditions.

New industry-standard hotbox for up to 400 bar and up to 28 litres per minute. EQUIPMENT - Epoxy coated steel frame with stainless steel cover - 4-wheel chassis with solid rubber tyres - Connection hose 1,5m - Water inlet temperature max. 60° - Heating capacity approx. 90 kW - Water outlet temperature in the steam range up to max. 140°C - With thermal switch and flow monitor Diesel tank: 20L Power supply: 1x 230V Dimensions: (L x W x H): 700mm x 570mm x 800mm Weight: 65kg Shipping possible. Errors and prior sale excepted. We refer to our terms and conditions.

Code: 0328 Brand: ITALPRESSE Model: GL / 14,5 - 50 - 420 T - CE Standard Hydraulic press for composite materials and solid surfaces, moulds and decorative panels, suitable for use in the aerospace, aviation, woodworking, furniture, interior design, automotive, shipbuilding, construction, energy, defence, sports and public transport sectors, and various – CE Standard – Year 2005 Technical data: N°5 solid steel plates 1450 x 500 mm N° 3 pistons Diathermic oil heating Total thrust 420 tonnes Working diagram - see enclosed diagram Max power 9,3 Kw Full-load current 19 A The oil tank is located on top of the press and is fitted with a sight glass for checking the oil level Fluid (oil) temperature controller Two-hand control for closing the press Photocell safety barriers Fixed safety guards

New industry-standard hotbox for up to 300 bar and up to 28 litres per minute. EQUIPMENT - Epoxy coated steel frame with stainless steel cover - 4-wheel chassis with solid rubber tyres - Connection hose 1,5m - Water inlet temperature max. 60° - Heating capacity approx. 90 kW - Water outlet temperature in the steam range up to max. 140°C - With thermal switch and flow monitor Diesel tank: 20L Power supply: 1x 230V Dimensions: (L x W x H): 700mm x 570mm x 800mm Weight: 65kg Shipping possible. Errors and prior sale excepted. We refer to our terms and conditions.

New hotbox in the industry standard for max. 200 bar and up to 28 liters per minute. EQUIPMENT - Epoxy coated steel frame with stainless steel cover - 4-wheel chassis with solid rubber tyres - Connection hose 1,5m - Water inlet temperature max. 60° - Heating capacity approx. 90 kW - Water outlet temperature in the steam range up to max. 140°C - With thermal switch and flow monitor Diesel tank: 20L Power supply: 1x 230V Dimensions: (L x W x H): 700mm x 570mm x 800mm Weight: 65kg Shipping possible. Errors and prior sale excepted. We refer to our terms and conditions.

Nilsfisk ALTO NEPTUNE 8, Price: 3.500 € netto, year of construction 2008. Hot water high-pressure cleaner for the most demanding cleaning tasks. The device combines powerful pressure with high water output, which is needed for cleaning heavy soils in agriculture, construction, transport or industry. In addition to the convincing cleaning effect, the high alluvial performance is particularly effective. Price is negotiable. Shipping possible. The sale is carried out on behalf of the customer. Prior sale and error excepted. The terms and conditions of Cleantec-MR apply.

Machine name: Chamber filter press used Manufacturer: Netzsch Type: 1000 /110 Year of Make: 1996 Design: Side-spar press Filter pressure: 15 bar Press capacity: approx. 2509 liters Procedure: Closed Filter area: Approx. 163 m2 Plate format: 1000 x 1000 mm Number of plates: 100 Panel Material: Polypropylene Plate Conveyor: Automatic Filter Cloth Washer: Yes Cake thickness: 30 mm Closing pressure: 385 bar Dimensions: L 9,347 x W 2,245 x H 2,435 mm Curb weight: 11,800 kg Tech. Documentation: Yes Note: It will be available from January 2025 Accessories: A control cabinet, a control cabinet, a hydraulic system, a light barrier, a filter cloth washer and drip plates Condition: Used Price: On request

Capacity 100 ton Table 880x715 mm Max. sheet thickness 3 mm Stroke per min. 360 Stroke 25 mm Ram adjustment 70 mm Distance Ram-table 400 mm 15 kW Dimensions LxWxH 3300x1600x2600 mm Total weight 10 tons

Make: RIJVA Model: 502/1 S/N: 405 Cap: 12 tons

Portal straightening press with 400 T capacity Oil-hydraulic double column press a) No-load and pressing speed up to 17 mm/sec b) Opening speed up to 60 mm/sec c) Table size 6000x3000mm d) Open height 1500 mm e) Total size approx. LBH 6000 x 5000 x 4500 mm f) OIL temperature display on the tank g) Lubrication via lubrication nipples h) table in grid construction, i) Operation on swivel arm, mounted on the bridge j) Pressure setting from 60 T to 400 T via MONITOR k) Bridge moves through two geared motors, over racks l) Cylinder moves to the left and right over racks m) Machine body powder-coated, or double-painted n) T-grooves according to customer requirements o) Cylinder induction hardened PORTAL PRESS Thermally neutral 80 – 120 °C Number of operating pages 3 pages Forces Pressing force max. 4000 kN Free tearing force ...

New VDL 2D chiseling machine with the possibility of automatic drilling at distances of 25 and 32 with the possibility of tilting and turning in 2 directions. Technical parameters: Control of the machine with 1 lever Power of the main motor: 1.5 kW Tool speed: 2850 rpm Spindle diameter: 3 - 16 mm Stroke of the spindle: 180 mm Dimensions of the table: 600 x 450 mm Weight of the machine: 320 kg

Manufacturer Erfurt Pressen Machine type Leinhaas Technology Country of origin Germany (BRD) Machine data Parameter Value Unit / Notes Max. press force 4500 kN Stroke rate (continuous) min. 15 strokes/min Max. stroke rate (tool designed for) 75 strokes/min Ram stroke 3 – 200 mm Ram adjustment 120 mm Installation height (min.) 600 mm Max. installation height 670 mm Dimensions of press table Press table length 2000 mm Press table width 1250 mm T-slots (press table) DIN 650 – 28 H12 Number of T-slots (table) 11 pcs Distance between T-slots 150 mm Dimensions of press ram Slide length 2000 mm Slide width 1200 mm T-slots (slide) DIN 650 – 22 H12 Number of T-slots (slide) 13 pcs Distance between T-slots 150 mm Press frame opening Side opening 900 mm Front opening 2200 mm Tool clamping Tool clamping height (upper tool) 80 mm Tool clamping h ...

2 x 10 T, adjustable from 1.3 to 10 T Plunger size 250x250mm forward 10 mm second Backwards 25 mm second Travel 100 mm per side, Interior 200 to 400 mm Two-hand operation Motor 1 KW Tank for 60 L hydraulic oil the machine can also be supplied in other sizes and thicknesses.

Portal straightening press with 300 T capacity a) No-load and pressing speed up to 17 mm/sec b) Opening speed up to 55 mm/sec c) Table size 2500x1600mm d) Open height 700 mm e) Total size approx. LBH 4500 x 2300 x 3700 mm f) OIL temperature display on the tank g) Lubrication via lubrication nipples h) Table in grid construction, with T grooves according to customer requirements, otherwise 22mm i) Operation on swivel arm, mounted on the bridge j) Pressure setting from 50 T to 300 Tvia MONITOR k) Bridge moves through two geared motors, over racks l) Cylinder moves to the left and right over racks m) Machine body double painted n) Cylinder induction hardened Design Press type PORTALPRESSE Thermally neutral 80 – 120 °C Number of operating pages 3 pages Forces Pressing force max. 3,000 kN Free tearing force max. 500 kN Pressure build-up time Closed tool St ...

DIEFFENBACHER PO-F 1250 A hydraulic press was built in Germany in 1981 by J. Dieffenbacher GmbH & Co. The machine was regularly maintained and upgraded throughout its service life. In 2016, a major upgrade was carried out, which included replacing the electrical cabinet, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The piston seals were also replaced and measuring scales were added for precise position measurement of the slider, top ejector and lower die cushion. The DIEFFENBACHER PO-F 1250 A is an extremely versatile hydraulic press for demanding metal forming applications. Its main purpose is die stamping of steel components, calibration of forgings, dogging, hot and cold forging, cold forming and other operations that require very high press forces. All these machining processes are performed with a high press force of up to 1250 tonn ...

Precise and heavy machine for drilling slotted holes. The maximum hole length is optional. In the standard version, it is 400 mm. The tool is fixed. The height is adjusted by raising the work table. Spindle power: 1.5 or 2.2 kW

SPECIFICATIONS: Vertical frame press for windows and doors Hydraulic operation machining length mm: 3,000 machining height mm: 2,000 Installed capacity KW: 1.6 Beam 2 horizontal bars 3 Vertical bars with pusher

ARISA S-2-400-260-FD mechanical press was built in 2000 in Spain by Arisa S.A. (now Nidec Press & Automation Co. (NP&A)). The machine on offer is an excellent choice for series production of components used in the broadly defined automotive or machinery industry. It enables precise punching and stamping of metal parts. All these machining processes are performed with a high press force of up to 400 tonnes, which, combined with a highly dynamic slider, guarantees the best machining results. The ARISA S-2-400-260-FD features a robust, stress-relieved gantry design with an open side wall. This design maintains high rigidity, stable parameters and repeatability during even the most intensive operations with high press force. It is distinguished by the use of two connecting rods, a flywheel drive and an eccentric pinion gear. This solution ensures even torque transmission and smooth and pr ...

Cold water high-pressure cleaner and hydraulic oil demand unit. Working pressure: Infinitely variable up to 320 bar. Required quantity: up to 21l /min (1,260 l/h) Pump: 3-plunger, all-ceramic Engine: 2 cylinders 4 stroke petrol engine Motor power: 16.4 kW Speed motor/pump: 3,250/1,450 rpm Pump drive: Gearbox Fuel consumption:approx. 5.5l/h Volume fuel tank: 20l Pressure outlet (water) M221,5 AG Heating capacity Olbrenner Empty Weight: 110kg Dimensions(LWH) 757999cm Article no.: 1 486 089

TMP VORONEZH KA2536 crank press was built in 1979 in the USSR by the Voronezh Mechanical Press Plant (Воронежский механический завод). The offered machine is perfect for many industries, especially those which require high press force and high repeatability of produced parts. This is because it enables even the most demanding metal forming processes to be performed, i.e. stamping of structural components, forming of parts, hot and cold forging, deep drawing operations and the production of parts with a large surface area. All of these machining processes are performed with a high press force of 400 tonnes and can be carried out continuously, increasing production efficiency and reducing downtime to a minimum. The crank mechanism used ensures uniform force transfer, which translates into precise slider feed and repeatability of each cycle. This solution is part ...

DIEFFENBACHER PO 500A hydraulic press was built in 1978 in Germany by J. Dieffenbacher GmbH & Co. The machine has been regularly maintained and upgraded throughout its service life. In 2017, a major upgrade was carried out, which included replacing the electrical cabinet, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The seals and electrical system were also replaced. The DIEFFENBACHER PO 500A is the perfect choice for even the most demanding metal forming operations. It enables the execution of such operations as die stamping, punching, calibration of forgings and hot and cold bending. All these machining processes are performed with a high press force of up to 500 tonnes, which, combined with a highly dynamic slider, guarantees the best machining results. The machine is also characterised by a rigid body made of thick steel plates and a ...

Cold water high-pressure cleaner Working pressure: infinitely variable up to 350 bar Required quantity:up to 21l/min (1.260l/h) Pump:3-Plunger All-Ceramic Engine:2 Cyilinder, Hatz Diesel,air-throated Motor power:17 kW Speed motor/pump: 2,900/1,450 rpm Pump drive: V-belt Fuel consumption:approx. 4,0l/h Volume fuel tank:20l Pressure outlet (water):M221.5AG Heating capacity Olbrenner Empty Weight:215kg Mass(LWH) 918096 Article no.: 1 492 060 or 1 492 002

SMG DS 40 hydraulic press was built in 2000 in Germany by SMG Süddeutsche Maschinenbau GmbH. The machine, which is characterised by high reliability, is used in metal stamping and punching. The machining process is performed with a high press force of 40 tonnes, which, combined with a rigid body, ensures the manufacture of highly repeatable and perfectly precise parts. The parameters, i.e. the ram speed, the position of the work tables and the press force, are adjusted by means of a simple control based on limit switches. The SMG press weighs 4 tonnes. Technical specifications of the SMG DS 40 press - maximum press force (adjustable): 40 t - work table dimensions (L x W): 600 x 400 mm - stroke of upper working table: 150 mm - distance between work tables: 400 mm - dimensions (L x W x H): 1230 x 570 x 2500 mm - weight of the SMG DS40 machine: 4 t

Hot and cold water high-pressure cleaners Working pressure:infinitely variable up to 350 bar max requirement quantity:16l/min Pump:3 Plunger,All-ceramic Engine:Kubota 3-cylinder diesel Motor power:13kW Speed motor & pump: 3000/1,090 rpm Pump drive:V-belts Fuel consumption:3,9l/h Volume of carbon tank:70l Volume water tank:300l Pressure outlet (water) M22 1.5IG Heating capacity olburner: max1115kW (approx. 95°C) Consumption Olbrenner: approx. 7l/h Construction:self-supporting frame on frame with forklift pockets Empty weight:about 680kg Mass(LWH) 152122146 Dimensions open (LWH) 183122195 Article no.: 1 480 030

Hot and cold water high-pressure cleaner Working pressure: infinitely variable up to 220 bar max demand quantity 26l/min Pump:3-Plunger,All-Ceramic Engine: Kubota 3-cyilinder diesel Motor power: 13kW Speed motor and pump: 3,000/1,760 rpm Pump drive: V-belt Fuel consumption: 3,9l/h Volume fuel tank: 70l Pressure outlet: (water): M22 1.5 AG Heating capacity Olbrenner : max 1115kW (ca 95° C) Consumption Olbrenner: approx. 7l/h Construction: Skid - Construction Empty weight: about 420kg Dimensions(LWH) 12080112cm Article no.: 1 546 712

BECKER & VAN HÜLLEN deep drawing press was built in Germany by Becker & van Hüllen Niederrheinische Maschinenfabrik GmbH & Co. KG. The machine has been continuously maintained and upgraded throughout its service life. In 2022, a major upgrade was carried out, which included replacing the seals, upgrading the control system, installing light curtains and adding a SIEMENS SIMATIC HMI TOUCH touchscreen operator panel. The BECKER & VAN HUELLEN 650T is used in industries specialising in stamping, production of automotive parts, tanks and other parts that require high press force and multi-stage forming. Its main purpose is deep drawing. The machining process is performed with a high press force of up to 650 tonnes. The two-stage design allows successive forming stages to be carried out in a single work cycle, thus enabling the manufacture of parts with even the most complex shapes. The m ...

Nominal force 100 t Stroke - 250 mm motor 3 kW more info on request

Technical details Pressure 110 t Technology Passage width 1200 x 1000 mm Stroke 1200 mm Machine weight approx. 12 t Space requirement approx. 4500 x 4300 x 2700 mm Master cylinder 1 piece Installation height (distance table to plunger plate) 1200 mm Table height 700 mm Table can be extended by 1200 mm Table tiltable by 45 degrees Upper tool folds down by 180 degrees Table rotatable by 180 degrees Table load max. 10 t Travel speed of the table 25 mm/sec Flow speed 195 mm/sec Return speed 130 mm/sec Working speed adjustable from 0 to 10 mm/sec. Table area between the columns 1250 x 1000 mm Engines WEG Accessories Paint structure RAL 7035 (light grey) Additional information Painting cladding, doors, maintenance balcony RAL 1021 (Yellow) Painting accessories RAL 7021 (dark grey) Columns and cylinders are made of tool steel SAE 1045 (identical to German standard C4 ...

280T Servo Double Column Heating Press with Heating Plates We can offer you this press at a particularly low price, as the machine is already under construction and the original customer has withdrawn from the order for two identical machines. This makes it possible to purchase a high-quality servo-hydraulic double-column press with heating plates at attractive conditions and at comparatively short notice. The photos shown show similar, already built machines from the factory and serve as example pictures. Technical data + information: General information Press force: 280 t Type: Servo Double Column Heating Press Cylinder: 1 cylinder Guided tour: 4 column guides Clear width between the uprights: 1,250 mm Cylinder stroke: 600 mm Max. distance between heating plates: 800 mm Table height from the floor incl. damper plates and heating plate: 900 mm Total height approx.: 3, ...

Nestro briquetting press BP 1101 - with daily storage tank and discharge Product name: Briquetting press Type: BP1101 / 710045 Manufacturer: Nestro Machine number: 64637 Year of construction: 1992 Condition: used, functional, cleaned The briquetting press consists of four components: 1. Pressing unit mounted on the base frame 2. Daily storage container 3. Control cabinet 4. Hydraulic unit with motor and pump technical details: Motor power: 7.5 kW Voltage: 380 V / 50Hz Current: 16.5 A Rotation: 1,440 rpm Operating hours: 5,390 hydraulic tank oil pump: 170 l Briquetting capacity: approx. 70-90 kg/h - Articulated arm discharge in the daily storage container - Daily storage tank with connection nozzle 350 mm diameter Container dimensions (L x W x H): 2,400 x 2,400 x 1,600 mm Installation dimensions with metal pedestal (L x W x H): 2,600 x 2,600 x 2,350 mm  ...

for pressing PET bottles

Inv. Num. : 5698 Type: LKT 250 Producer: METALPRESS Created: 1974, GO 2002 Parameters: Compressive force: 250 t Table length: 1150 mm Top table width: 1580 mm Maximum stroke rate top table: 7-25 1/min Ram stroke: 250 mm Adjusting the plunger: 100 mm Machine weight: 22950 kg GO 2002: converted to hydraulic clutch electronic control

1100T Servo Double Column Heating Press with Heating Plates We can offer you this press at a particularly low price, as the machine is already under construction and the original customer has withdrawn from the order for two identical machines. This makes it possible to purchase a high-quality servo-hydraulic double-column press with heating plates at attractive conditions and at comparatively short notice. The photos shown show similar, already built machines from the factory and serve as example pictures. Technical data + information: General information Press force: 1,100 t Type: Servo Double Column Heating Press Cylinder: 1 cylinder Guide: 4 column guides (Ø 150 mm) Clear width between the uprights: 1,600 mm Cylinder stroke: 600 mm Max. distance between heating plates: 800 mm Table height from the floor incl. damper plates and heating plate: 1,000 mm Total height  ...

For sale is a tested pressure vessel with a capacity of 900 liters. The container from the well-known manufacturer OKS is built in 2023 and has not yet been used. Due to the existing TÜV test, the container complies with the applicable regulations and is ideal for use in industry, trade or even in the hobby sector. Technical data: - Manufacturer: OKS Otto Klein GmbH - Year of construction: 2023 - Volume: 900 liters - Max. operating pressure: 11 bar - Test pressure: 16.5 bar - Temperature range: -10 °C to +80 °C - Medium: Air / Nitrogen - Corrosion surcharge: 0.5 mm - TÜV test available (04/2023) - Complies with Directive 2014/29/EU If you have any questions, please feel free to contact us at any time

Stock number: U2391 Used rotary tablet press by Killian (DE) model T100/18 EU-B. Machine has 18 punches. Die dimensions: diameter 30.16 mm x height 22.22 mm. Working output from 5400 tablets up to 129600 tablets, depending on size, shape and product. Maximal tablet diameter 16 mm. Maximal filling up to 16 mm. Machine has hydraulical compression. Pre-compression force up to 60 kN. Main compression force up to 65 kN. Machine has local control panel and electric cabinet with work recording computer and printer. Technical documentation included with machine. Toolings not included.

Stationary high-pressure pump unit Hammelmann HDP 142 on base frame. Similar but no Kamat, Uraca, Woma. Pump type: HDP 142 Operating pressure: 610 bar Flow rate: 78 l/min. Drive speed: 1500 rpm. Drive power: 86 kW with AC M 280 M-4/HE electric motor 90 kW, IP55, with pressure control valve, with safety valve, with oil cooling system. Dimensions LxWxH: approx. 1,700x850x1,450 mm Weight: approx. 1,200 kg Year of construction: 2018 Condition: after service by Hammelmann in October 2020 only a few weeks run and for more than a year out of operation. In very good used condition.

Compact electric press brake C9 CoastOne - Made in Finland Pressing force: 22T Bending length: 900mm Spindles: 1x22T Control: TC15-2D graphics Backgauge: 2 axis controlled X-R axles Lazersafe photoelectric sensor: 100mm/s delivery speed Bending tool holder: Type A / R1 / AMADA / Promecam Quick release system TEDA Speed Grip 4x Adapter Front support tables Front light 1x set of bending tools incl. 36 months warranty after installation Delivery excl.; at call Viewing under electricity possible at any time by appointment!

Differential pressure indicator, transmitter, monitor, sensor, differential pressure indicator, differential pressure switch -Manufacturer: Dürr -Part No.: 4Q 01 21 300 -Article No.: DE45E50040PKD232 -Basic measuring range: 0...10 kPa -Dimensions: 105/90/H70 mm -Weight: 0.3 kg

pressure: 160 t stroke: 400 mm table surface area: 1100 x 635 mm pressing speed: 6,57 mm/sec return speed: 11,62 mm/sec oil pressure max. in the work cylinder: 412 bar oil volume: 40 l dia. of piston: 145 mm column daylight: 1120 mm voltage: 400 V / 50 Hz dist. between pillars (front to rear): 350 mm total power requirement: 5,5 kW weight of the machine ca.: 1,2 t dimensions of the machine ca.: 1,7 x 0,9 x 2,1 m • unused workshop press, • manual and hydraulical operation, • horizontally moveable pressure cylinder, • working table hydraulical adjustable in height, • cylinder Ø 220 mm, piston base Ø 145 mm. • 2 support prisms • CE marking The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

No hidden costs with us The advertisement concerns the basic version of the machine. You can get all prices and extras by contacting our technical and sales representatives. We always provide the final amount on quotes if the contract is signed within the valid period. We always quote the cost of shipping from our warehouse in Poland. Hydraulic press brake PBO-3212-CNC OT-41 Specifications - Nominal pressure: 1250 kN - Max working length 3200 mm - Throat depth: 320 mm - Max stroke: 120 mm - Daylight: 390 mm - Distance between side frames: 2700 mm - Max backgauge distance: 600 mm - Nominal motor power: 7.5 kW - Length: 3700 mm - Width: 1800 mm - Height: 2450 mm - Weight: 7000.0 kg Tools - Front supports: 2 pcs - Automatic backgauge distance regulation (X-axis): servo motor - Ram control (Y-axis): servo motor - Finger height adjustment (R axis): manual - Type  ...

Line regulating valve, shut-off valve, ball shut-off valve, ball valve, ball valve, pressure relief valve -Manufacturer: Superior, pressure relief valve, unused original packaging -Type: 3220-360/360 PSI -Dimension box: 105/50/H50 mm -Weight: 0.3 kg

Stop for press brake, bending machine, guillotine shear, drive shaft -Drive shafts: for stop, from press brake EHT type EHP 11-40, 2 pieces -Length: 515 mm -Hole: Ø 25 mm -Price: complete -Dimensions: Ø 50 x 515 mm -Weight 5.1 kg/pc.