jones and shipman used for sale

Automated Clean In Place (CIP), Continuous hot water, single pass, belt washer, With Stein Humitroll moisture monitor and control, Belt width: 40 inch, 1010 mm, Heating: thermal fluid, 2 x 460kW, Steam: max 2 x 545 kg/hr, Compressed air: 6 - 10 Bar, Power: 3 x 400V, 50Hz, 63kW, Dimensions: 22500 x 3000 x 3000 mm

Key data: 510 mm, 1500 mm, 300 U/min

Hello, I get this lathe at the beginning of August. With a lot of accessories: steady rest, lathe chuck – clamping jaws, quick-change holder and.. Heidenreich & Harbeck Type Hanseat 480 Year of manufacture 1980 Center height 255 mm Turning diameter over support 300 mm Center width 1500 mm 24 speeds from 23.6 to 2500 n1/min Tailstock MK 4 Chuck F 250 Motor 380 Volt 11 kW Transport dimensions: Length 3200 mm Width 1200 mm Height 1550 mm Weight 2.5 to. Lathe Hanseat 480 incl. accessories St Description 1 instruction manual 1 Lynette small 1 Lynette large 1 4- Jaw chuck small 1 4- Jaw chuck large 15 quick-change tool holders Set designation 2 jaws for 4-jaw chuck 38 jaws for 3-jaw chuck

Teflon infeed, hold down belt, circulation pump, oil level control, sediment removal, electric hoists, prepared for CO2 fire extinguisher, Including separate infeed belt, Machine delivered with CFS VTC1100-194 oiltank and oilpump, Belt width: 500 mm, Frying length: 3000 mm, Heating: electric, Power: 3 x 380V, 50Hz, 72kW, Weight: 2500 kg, Dimensions: 6300 x 1700 x 3100 mm

Two Index CNC turning and milling centers are available. 1) Index G250, year of manufacture: 2008, swing diameter: 560mm, turning length: 800mm, bar capacity: 90mm, spindle diameter: 140mm, spindle speed: 3500rpm, spindle power: 43kW/57kW, torque: 275Nm/363Nm, indexing: 2.5°, tool speed: 6000rpm, tool drive power: 11kW, X/Z travel: 300mm/800mm, rapid traverse X: 30m/min, rapid traverse Z: 22.5m/min, feed force X/Z: 7200N/9000N, quill diameter: 65mm, machine dimensions X/Y/Z: approx. 7300mm/4000mm/2600mm, weight: approx. 14000kg, control: Siemens 840D C200-4D. 2) Index G300, year of manufacture: 1998, retrofit: 2022, turning diameter: 270mm, turning length: 710mm, max. swing diameter: 590mm, main spindle bore: 65mm, spindle diameter: 110mm, spindle speed: 5000rpm, torque: 275Nm, power: 43kW, tailstock center distance: 740mm, max. thrust force: 10kN, short slide travel X/Y: 215mm/180mm, s ...

Hold down belt, sediment removal, circulation pump, electric hoists, oil level control, Prepared for CO2 fire extinguisher, Belt width: 600, Frying length: 4500 mm, Heating: thermal oil, 214kW, Power: 3 x 380V, 50Hz, 10kW, Dimensions: 7400 x 1900 x 3150 mm, Weight: 2750 kg

4 Lenz CNC PCB drilling and routing machines are offered. 1) One CNC vertical PCB drilling and routing machine, Lenz LGX 460-2AL, year of manufacture: 1995, travel X/Y: approx. 550mm/460mm, rapid traverse X/Y: approx. 40m/min, max. drilling rate Z-axis: approx. 500strokes/min, spindles: Precise SC53H, spindle speed: approx. 20000rpm, tool holder: 3mm, tool capacity: 308, control: SIEB & MEYER CNC 44.00. Equipped with a cooling unit and a loader. Overall dimensions of the base machine X/Y/Z: approx. 1650mm/1700mm/2250mm, additional length of the loader unit: approx. 820mm. 2) One CNC vertical PCB drilling and routing machine, Lenz GX 460-2, year of manufacture: 1989, travel X/Y: approx. 550mm/460mm, number of spindles: 2, rapid traverse X/Y: approx. 15m/min, max. stack height Z-axis: approx. 10mm, tool holder: 3mm, tool capacity: 88, control: SIEB & MEYER CNC 45.00, equipped with a coolin ...

Teflon infeed, hold down belt, circulation pump, electric hoists, oil level control, prepared for CO2 fire surpression system, Belt width: 630 mm, Frying length: 5000 mm, Heating: thermic oil, 250kW, Power: 3 x 400V, 50Hz, 11kW, Dimensions: 9100 x 1900 x 2900 mm

A complete Facma/Cerquetani hazelnut harvesting and processing line for processing hazelnuts from crop reception through sorting, cleaning and grading is available. 1) Facma hazelnut harvester. 2) Ditta Cerquetani Antonio collection and transport trailer. 3) Facma combined processing, cleaning, rotary screen and screening unit. 4) Facma washing and wet cleaning unit. 5) Drying system with drying silo, blower and electrical control cabinet. 6) Facma inclined conveyor with feed hopper. 7) Facma horizontal conveyor and selection belt. 8) Facma sorting, inspection and grading table. Including various peripheral equipment and accessories. Documentation available. Inspection on site is possible.

Key data: 150 KW, 400 V

Wolf Gas CHP GTK 140E01 Gas electricity and heat generators from 2022, 0 operating hours (never run), with control and silencer. 140 KWel x 1,500 rpm, 400 V / 50 Hz. AC generator: Marelli MXB-E 250 MB/4, 250 KVA Manufacturer: Wolf Model No.: GTK 140E01 Type: Natural Gas CHP Serial Number: 3260 Power [KWel]: 140 Power [KWth]: 216 Power [KWgas]: 384 Engine: MAN E2876 E312 Motor power [KW]: 150 Year of Make: 2021 Hours: 0 hours (never run) Weight unit [kg]: 3,500 Dimensions LxWxH [m]: 3.30 x 1.30 x 2.20 AC Generator MarelliMotori MXB-E 250 MB Manufacturer: MarelliMotori Model: MXB-E 250MB Type: AC Synchronous Generator Serial Number: 1033344 Power [KVA]: 250 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 361 Speed [1/min]: 1,500 Year of Make: 2021 Weight [kg]: 680

Used Isobaric Complete Bottling Line for Still and Sparkling Wine up to 4500 bph This complete bottling line has been designed and configured to provide a high-quality, consistent filling process for both still and sparkling wines. Built around an isobaric tribloc system, it integrates rinsing, filling, and capping functions in a continuous flow, ensuring excellent efficiency while maintaining product integrity. The line is currently set up for still wines at an output of 4,500 bottles per hour and for sparkling wines at 3,000 bottles per hour. It is already technically prepared for sparkling wine production and only requires the addition of a mushroom corker, a capsule applicator for spumante hoods, and a heating tunnel if needed. The system is equipped with dedicated conveyors, a centralized lubrication system, and separate control panels for conveyor management, enabling straightforwa ...

Used Complete Line for PET and Glass 2007 Rinsing Machine: Manufacturer: Dipran Model: Marea 12P Year: 2007 The used complete line for PET and glass bottles includes a high-quality rinsing machine. Manufactured by Dipran in 2007, the model is Marea 12P. This machine ensures thorough and efficient rinsing of the bottles, preparing them for the filling process. Filling Monoblock: Manufacturer: NELDEN Model: Giove FC VA 20-1 Big Year: 2010 The line also features a reliable filling monoblock manufactured by NELDEN. The model is Giove FC VA 20-1 Big, and it was produced in 2010. Using a gravity filling method, this monoblock precisely fills the bottles with the desired product, ensuring accuracy and consistency. Labeling Machine: Manufacturer: Newtec Model: Fix S2 E2 Year: 2007 Included in the line is a Newtec labeling machine, model Fix S2 E2, manufactured in 2007. With its mechanical cam, t ...

Used bottling line PROCOMAC for still and sparkling water up to 12000 bph We offer a complete bottling line for natural and carbonated mineral water, specifically designed to meet the complex needs of technicians and industry experts. This solution not only handles bottle formats from 0.5 to 2 liters but also produces up to 12,000 bottles per hour, ensuring high reliability and excellent performance.. SIPA Blow Molder and Preform Management The SIPA SFR 12 blow molder, manufactured in 2000, initiates the production process. It efficiently manages preforms using a dumper and elevator-orienter. Furthermore, the integrated cooling chiller and four sets of molds allow the machine to produce bottles of various sizes with both precision and flexibility. As a result, it ensures smooth operations throughout the initial production phase. PROCOMAC Monoblock: The Core of the System The PROCOMAC mon ...

Description Item # 7526 – DOUBLE TWIST WRAPPER for comfit pieces, chocolate creams and sweets with solid or soft filling Manufactured by NAGEMA Model EU7 up to 300 pieces per minute, With appropriate parts would be suitable for product sizes 20 to 60mms long x 13 to 27mms wide x 8 to 20mms high,

Melting and holding furnace StrikoWestofen MH II-T 6000/3500 G-eg, built in 2021, heating capacity 2,600 kW, capacity 6,000 kg, melting capacity 3,500 kg/h, max. melting pool temperature 760°C, max. furnace room temperature 1,050°C, height approx. 8,043 mm, with Striko K2000E feeder, built in 2021, with elevator for transport boxes

Secure available PERI MX 100 x 240 concreting platforms for professional formwork, concrete construction, and infrastructure projects 🚀 These proven working and concreting platforms provide additional safety and efficiency on site and are an ideal addition to existing formwork systems 🔥   The offered PERI MX 100 x 240 concreting platforms are ideally suited for concreting operations, formwork work, and creating safe working areas on wall formwork and concrete construction projects. Thanks to their robust design, they offer versatile applications and support efficient site operations ⚡   The platforms are available in 1 Star and 2 Star quality and provide a cost-effective alternative to higher-graded material. Particularly attractive for companies that rely on proven PERI formwork components while maintaining a cost-conscious purchasing strategy  ...

🧣📦 Last chance for a smart site upgrade: The Doka cavity wall bracket 60 is now available in a clearance bundle †by pallet , fairly priced and ready to ship ! 💥 Whether you need a pouring platform , edge protection solution or system extension †this bracket is a perfect match for anyone using the Doka Xsafe XP system . Compatible. Durable. Cost-effective. 🔎 Why this deal makes sense: ✅ Compatible with Xsafe XP †a smart add-on for your edge protection system ✅ Versatile use †for pouring platforms and barriers on precast hollow-wall elements ✅ Galvanised finish †durable, resilient and immediately ready for use ✅ Sold by full pallet (10 pcs) †condition-based price tiers available ✅ Immediate availability †no waiting, no quote ping-pong ✅ Clearance pricing †sma ...

💥 You’re working with the PERI bracket platform system MXK ? Then this offer is made for you: We’re selling a complete set of certified original PERI bracket decks †accurate fit, durable and ready to go. 💸 Perfect for anyone looking to buy PERI MXK plankings or upgrade their existing system. 🔩 What’s included: ✅ Original PERI parts †no replicas ✅ Lengths: 0.90   m | 1.20   m | 2.40   m ✅ Material: Aluminium-wood combination ✅ Certified and ready to use ✅ Safely bundled on transport supports 💡 Ideal for concreting and intermediate platforms with PERI MAXIMO. 💸 Total price: €1,699 †only while stock lasts. ⏳ First come, first build. Secure your package now †this offer won’t come twice. 🛒 Get in touch today and ...

Used dosing bunker with moving floor and discharge roller Manufacturer: HARTNER Type: active vario-storage (AVS System 2100 - 40) Year of Make: 2004 Technical data: Overall width: approx. 2,670 mm Length: approx. 12,000 mm Width: approx. 2,670 mm Height: approx. 2,500 mm

Overview This lot comprises two VIG pressure tanks of 5,000 litres each, built in 2019 by VIG Vertrieb Industrieller Güter (Kreuztal, Germany). The vessels are CE-marked pressure vessels according to EC pressure equipment directive 2014/68/EU and were last used as activated carbon filters in a brewery’s water treatment. Each tank is fitted with a filter star; the filter candles show light damage. The tanks are interconnected with DN 65 piping and come with butterfly valves for cleaning, draining and shut-off as well as vacuum/check valves. With their young year of construction and availability as a pair, the vessels suit filtration and pressure-holding duties in breweries and beverage plants alike. Technical data Manufacturer: VIG Vertrieb Industrieller Güter (Kreuztal, Germany) Year of manufacture: 2019 Number of tanks: 2 Volume: 5,000 l per tank Max. operating pressure (PS): 6 bar  ...

A custom-built slitting and straightening machine Grossmann/BFW for aluminum strip is available. Strip width: 35mm, Straightening unit: multi-roll, Knife type: rotary knives, Strip guidance: roller guidance, Tension control: KTC800A. Documentation available. An on-site inspection is possible.

Technical Data Max. Workpiece Diameter: 3,800 mm Max. Rotational Speed: 100 min⁻¹ Workpiece Clamping: Manual Chuck: Röhm Tool Holder: Capto C8 Tool Magazines: 2 × 47 slots (94 slots total) Travel Paths X1-Axis (Right Support): 3,200 mm X2-Axis (Left Support): 2,800 mm Z1-Axis (Right Support): 750 mm Z2-Axis (Left Support): 750 mm Workpiece Spindle Speed Range up to 100 min⁻¹ Nominal Power: 67.4 kW Maximum Power: 202.2 kW Max. Torque: 71.6 kNm Max. Table Load: 35,000 kg Water-Cooled Motor Spindle Multifunction Head B-Axis with Stepless Positioning Swivel Range: 180° Driven Tools up to 6,000 min⁻¹ Hydraulic Clamping Direct Measurement System High-Pressure Cooling up to 70 bar Tool Magazines 2 Chain Magazines with 47 Slots Each Tool Diameter up to 120 mm Up to 150 mm with Appropriate Magazine Loading Max. Tool Length: 400 mm Max. Tool Weight: 20 k ...

UsedPaal RS40 residual roll saw / splitter and roll unwinders. Year of manufacture: 1998 Max. roll diameter 400 mm Max. roll length 2.500 mm Saw blade diameter 600 mm Drive power 19 kW Max. enclosure width approx. 1000 mm Max. machine length approx. 9000 mm Machine weight about 2,400 kg max. transport chain speed: 2.45 to 11.75 m/min. Throughput capacity depending on roll length and saw cut depth: 87.5 to 175 m/h

Used SCM S520 NOVA thickness planer useful working width mm. 520 Standard 4-knife shaft working height min/max mm. 3,5/300 max removal mm. 8 Double rubberized drive roller at the exit nr. 1 toothed drive roller at the inlet Electric Deck Lift 4-speed feed Star/delta starter Shaft rotation speed 4500 rpm Weight kg. 687 CE compliant

A Se-Ma meat grinder and bowl cutter combination machine is available. Bowl cutter volume: approx. 50l, bowl diameter: 940mm, upper edge height on bowl cutter side: 820mm, knife heads: 6, grinder plate diameter: 130mm, feed bowl internal dimensions X/Y: 600mm/820mm, feed bowl external dimensions X/Y: 630mm/850mm, upper edge height on grinder side: 1040mm, machine dimensions X/Y/Z: approx. 1800mm/1050mm/1400mm, weight: approx. 500kg. The machine is not equipped with a mixing gear. An on-site inspection is possible.

Key data: 5 KW, 400 V

Viessmann Gas CHP Vitobloc 200 EM-5/13 Gas electricity and heat generators from 2013 with unknown operating hours, closed module. 5.5 KWel x 1,500 rpm, 400 V / 50 Hz. AC Generator: Leroy Somer LSA 40VS1 C 6/4 Manufacturer: Viessmann Model: Vitobloc 200 EM-5/13 Type: Natural Gas CHP Serial Number: 7459188 3 01862 105 Power [KWel]: 5.5 Power [KWth]: 13.5 Output [KWgas]: 20.2 AC Generator: Leroy Somer LSA 40VS1 C 6/4 Year of Make: 2013 Operating hours: unknown Dimensions LxWxH [m]: 1.50 x 0.80 x 1.30 Weight unit [kg]: 500

Heating output: 275kW, electrical output: 201kW, fuel: natural gas, engine: MTU E 3066 L3, engine cylinders: 6, overall efficiency: approx. 82%, generator rating: 276kVA, machine dimensions X/Y/Z: approx. 3550mm/1800mm/2100mm, weight: approx. 4500kg, operating hours: approx. 57557h. Documentation available. An on-site inspection is possible.

Technical Data Max. workpiece diameter: 3,800 mm Max. rotational speed: 100 min⁻¹ Workpiece clamping: manual Chuck: Röhm Tool holder: Capto C8 Tool magazines: 2 × 47 slots (94 slots total) Travel Paths X1-axis (right support): 3,200 mm X2-axis (left support): 2,800 mm Z1-axis (right support): 750 mm Z2-axis (left support): 750 mm Workpiece Spindle Speed range up to 100 min⁻¹ Nominal power: 67.4 kW Maximum power: 202.2 kW Max. torque: 71.6 kNm Max. table load: 35,000 kg Water-cooled motor spindle Multifunction Head B-axis with stepless positioning Swivel range: 180° Driven tools up to 6,000 min⁻¹ Hydraulic clamping Direct measuring system High-pressure cooling up to 70 bar Tool Magazines 2 chain magazines with 47 slots each Tool diameter up to 120 mm Up to 150 mm with appropriate magazine configuration Max. tool length: 400 mm Max. tool weight:  ...

An automatic gKteso post-processing and deburring center is available. Technology: 6D, axes: 5+1, working dimensions X/Y/Z: 500mm/500mm/300mm, max. travel speed: 1m/s, repeatability: 0.05mm, path accuracy: 0.1mm, max. flatness: 0.02mm, chucks: 2-jaw/3-jaw/4-jaw chucks, machine dimensions X/Y/Z: approx. 2400mm/1800mm/2900mm, operating hours: approx. 12541h. Including pneumatic chucks, safety light curtain, exchange table and 6D technology. Documentation available. An on-site inspection is possible.

Cat No.: 26-0064 Features Volume 1000 L Material No. V2A Exterior Surface IIID Surface inside IIID Total height 1845 mm Cylinder height 1250 mm Diameter 1130 mm Weight 184 kg Description Topsoil: Clapper bottom Threaded Socket DN50 Manhole CIP Connector Airlock connection DN50 Cylinder: Cooling jacket Insulation Level indicator Sample tap DN25 Dip Shaft Sleeve for Thermometer Underbody: Forward-drawn residual drain pipe with disc valve DN50 4 feet

We offer used accessories at a special net price. 40 x tripod/support leg, used = 15,00€/piece 127 x clevis/four-way head, used = 4,50€/piece If you have any questions, please call 0049 176 70044689 Mr. Becker Purchase and sale of scaffolding/formwork systems and construction machinery; Formwork restoration at fair conditions. Company SFS Meisterbetrieb Andreas Becker e. Kfm. Phone 07305/9562350 mobile: 0049 176 70044689 Mr. Becker Office/ Storage Address: Ulmer Straße 1 89614 Öpfingen Ulm Registration Court: HRA722943 VAT ID NUMBER: DE279047055

Sharp TC11 Table Cutter Volume: 11 litres very good condition completely in stainless steel 2 courses 3 cutter head Machine comes from a hobby butcher who gave up for reasons of age despite its good condition, the device must be thoroughly cleaned before use Video about test run available

turning length: 1000 mm turning diameter: 210 mm swing diameter over bed slide: 300 mm centre height: 167 mm spindle bore: 40 mm bed width: 210 mm turning speeds: 40 - 2500 U/min total power requirement: - kW weight of the machine ca.: 1000 kg. range L-W-H: 2000 x 1000 x 1700 mm Features: - Digital display - 3-jaw chuck - Chuck guard - Multifix quick-change tool holder - Chip deflector - Chuck guard - Coolant system - Bed stop - Instruction manual The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

TECHNICAL DATA: Working length: min. 350 mm – max. 3000 mm Working width: min. 20 mm – max. 230 mm Element thickness: min. 12 mm – max. 70 mm Feed speed: 10 to 50 m/min Installed power: 1.5 kW

turning length: 450 mm turning diameter over bed: 245 mm turning diameter over slide rest: 135 mm spindle bore: 23.0 mm tool adaptor: DIN 55021-4 quill:: 2 MK quill travel: 80.0 mm turning speeds: 60 - 3000 U/min bed width: 155 mm total power requirement: 1.2 / 1.5 kW voltage: 380 V weight of the machine ca.: 340 kg. range L-W-H: 1200 x 650 x 1330 mm from a vocational school (!) particularly suitable for precision turned parts The Primus series is the most compact precision sliding headstock and sliding headstock lathe (LZ) from WEILER. It is used in toolmaking, laboratories and training workshops as an absolute machine for precise work in the tightest of spaces. The machine is built for extremely tight tolerances. The hardened and ground machine bed ensures maximum for maximum vibration damping and durability. Features: - Robust lead/traction spindle lathe - 2-axis digital readout D60 ...

Ref.Nr. 00934 Designation of the system 6 x welding workstations Sweat source and Hand-welded pistones can be connected With CE Semi-automatic With turntable Manual Manufacturer unknown Model Schweiß M Pohl Year of manufacture 2011 and others Condition In Function

turning length: 450 mm turning diameter over bed: 245 mm turning diameter over slide rest: 135 mm spindle bore: 23.0 mm tool adaptor: DIN 55021-4 quill:: 2 MK quill travel: 80.0 mm turning speeds: 60 - 3000 U/min bed width: 155 mm total power requirement: 1.2 / 1.5 kW voltage: 380 V weight of the machine ca.: 340 kg. range L-W-H: 1200 x 650 x 1330 mm from a vocational school (!) particularly suitable for precision turned parts The Primus series is the most compact precision sliding headstock and sliding headstock lathe(LZ) from WEILER. It is used in toolmaking, laboratories and training workshops as an absolute machine for precise work in the tightest of spaces. The machine is built for extremely tight tolerances. The hardened and ground machine bed ensures maximum for maximum vibration damping and durability. Features: - Robust lead/traction spindle lathe - 2-axis digital readout D60- ...

Description Item #8817 – WAFER PRODUCTION LINE WITH CHOCOLATE ENROBING LINE (wafer stick oven and sheet wafer oven) Manufactured by HAAS/MORCOS Year 2020, Wafer line including : SHANGHAI KUIHONG FOOD MACHINERY FACTORY Wafer Roll/Tube Oven, suitable for both filled or hollow wafer rolls/tubes Also including a Mixing Machine, Pumping & Filling Machine, the Wafer Roll/Tube Oven, Cooling Conveyor, and a Ball Mill. SWA-31G Wafer Sheet Oven, plate sizes 290 x 460mms, 31-plates Wafer Sheet cooler type DEV-1.2 m One Spiral Contact cream spreading machine type STM Turning conveyor type WDB One Wafer book cooling tower type WKF 70 One Cream turbo mixer type TCM125 One Ejection Table for wafer blocks type ET One Wafer book cutter type MWDL Turbo dough mixer type TMN 120 Scraper machine type C40T High performance turbo mill type CS TU50-90 Stainless Steel 90degree Turntable, band width 500mms, foo ...

Description Item # 9358 - RUSK & CRUMB (Breadcrumb-Type Filler) PRODUCTION AND PACKAGING LINE Suitable for bakery crumb, coating crumb, and meat-industry filler manufacturing A complete, proven rusk and flake-bake production line, formerly processing 3 tonnes/hour of flour into 2.5 tonnes/hour of finished rusk and flake bake (used as a filler in sausages, pies, coatings and stuffing mixes). The line ran continuously until the site was sold in December 2025, with numerous safety upgrades installed throughout its operating life. Line includes: 2x Baker Perkins dough mixers – recently upgraded motors and gearboxes Dough sheet former – forms the dough sheet ahead of the oven Spooner oven – stainless steel panelling, three burners and controls renewed in 2024 Peg roller – breaks the biscuit sheet at oven exit Cracker – reduces biscuit to a manageable size for the next process 2x Mik ...

turning length: 1000 mm turning diameter: 330 mm turning dia. over face-slide: 198 mm turning dia. in gap: 476 mm spindle bore: 38.0 mm turning speeds: 70 - 2000 U/min bed width: 180 mm spindle taper: DIN ISO 702-2 Nr. 4 taper in tailstock: 3 MK quill travel: 110 mm total power requirement: 1.5 kW weight of the machine ca.: ca. 610 kg. range L-W-H: 1930 x 755 x 1300 mm Features - Ideal for technical schools, repair shops, and training workshops - Modern main spindle bearing assembly with precision-grade angular contact ball bearings - Single-lever chuck for the tailstock, adjustable for taper turning - Hardened and ground gears and shafts in the gearhead - Optimally suited for machining steel, non-ferrous materials, and plastics - Removable bridge for machining workpieces with large . diameters - To minimize the effects of vibration, the solid prismatic bed . is additionally equipped wit ...

turning diameter: 360 mm turning length: 1000 mm swing diameter over bed slide: 360 mm centre height: 180 mm turning speeds: 70-2400 U/min total power requirement: 2,2 kW weight of the machine ca.: 680 kg dimensions of the machine ca.: 2000x1500x900 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning length: 500 mm turning diameter over bed: 297 mm turning diameter over slide rest: 160 mm spindle bore: 36.0 mm tool adaptor: DIN 55022 Gr. 5 quill:: 3 MK quill travel: 90.0 mm turning speeds: 30 - 3550 U/min motor speeds:: 1410 / 2830 U/min total power requirement: 3.3 kW voltage: 380 V weight of the machine ca.: 620 kg. range L-W-H: 1420 x 700 x 1200 mm from a vocational school - in very good condition () particularly suitable for medium-precision turned parts Features: - Robust lead/feed screw lathe - RÖHM three-jaw chuck Ø 160 mm - Foldable lathe chuck guard - Chuck key - MULTIFIX steel holder A, with 3x new inserts - Movable tailstock - Swiveling machine light - Control panel, front left - Automatic feeds for face and upper support - Machine base, with cabinet door (storage space) - Chip splash guard rear panel - Emergency stop button - Operating instructions The data ...

Folding tap pointer: . tube diameter: 5 - 20 mm tag length: 50 - 100 mm total wight: 1,4 t Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round bar steel: 63 mm square edge steel: 55 mm flat steel: 100 x 25 mm : engine: 380 V, 6,3 kW weight: ca. 2.450 kg Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: gefült mit 43 Aufnahmen height: 2.200 mm width: 1.200 mm weight of the machine ca.: 300 kg : Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pointing milling machine: für Stangen carbide turnover plates: 4 Stück working area: Rund, Profil+vierkant mm working range: 80 (100) an 25 mm milling drive: 380/420V, 18,5 KW, 50 Hz kW revolutions per minute: Fräsantrieb: 1465 U/min : . clamping devices hydraulic pneumatic: hydraulisch infeed device: hydraulisch : ca. 5 lfdm x 300 mm : hydraulic power unit: Rexroth tank: 250 l coolant tank: mit Spänekasten l control panel: switchgear cabinet: mit Klimaanlage control: SIEMENS S 7-300 Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Year: ca. 1978 : für Stangenprofile und... : ... für Flachmaterial material thickness: max. 24 mm working length: 300 - 600 mm efective widths: 3 mal 170 mm drive motor: 400 V, 11 kW, 50 Hz : . Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 455 mm turning diameter over slide rest: 285 mm turning length: 1.000 mm center height over bed: 225 mm centre distance: 1.000 mm digital readout: 2-Achsen ANILAM bed width: 330 mm spindle taper: KK 6 DIN 55027 spindle bore: 45 mm turning speed range: 16 - 1.000 U/min power requirement: 3,0 / 4,2 kW taper in tailstock-quill: MK 4 dia. of quill: 62 mm quill stroke: 145 mm coolant: voltage: 400 V total power requirement: 4,5 kW weight of the machine ca.: 1,95 t dimensions of the machine ca.: 2,45 x 1,10 x 1,80 m - Serial-No.: 29-2561 - ANILAM 2-axis digital readout - 4-jaw tool holder - coolant equipment ATTENTION! Machine is sold without a chuck. Upon request and for an additional charge, the following 3-jaw spiral chucks can be included: - CENTER Ø 200 mm = 780.00 EUR - CENTER Ø 250 mm = 1,030.00 EUR The data for this ad was created with ModulMWS - the sof ...

turning diameter over bed: 440 mm turning diameter over slide rest: 240 mm turning length: 1500 mm spindle bore: 55 mm faceplate: 550 mm steady: 140 turning speeds: 40-1800 U/min digital readout: Haidenhain bed width: 340 mm steady: 140 mm 3-jaw chuck: 250 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m No. 62 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit ...

turning diameter over bed: 440 mm turning diameter over slide rest: 240 mm turning length: 1500 mm spindle bore: 55 mm faceplate: 400 mm turning speeds: 40-1800 U/min digital readout: Haidenhain bed width: 340 mm 3-jaw chuck: 250 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m No. 63 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team  ...

turning diameter over bed: 1420 mm turning diameter over slide rest: . mm turning length: 3150 mm faceplate: 500 mm turning speeds: 176 U/min steady: 160 mm total power requirement: kW weight of the machine ca.: 15,68 t dimensions of the machine ca.: m new control cabinet The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the sof ...