iron used for sale

Roll diameter: 600 mm; Stand projection: 570 mm; Cutting depth: 400mm; Swivel table: yes -0 to + 45Â; Table size: 830 x 600 mm; Belt speed: 1615m/min; Motor power: 3.75 kW / 400V; Engine braking: yes / automatic; Suction connection: 2 x 120mm; Machine length: 1190 mm; Machine width: 780 mm; Machine height: 2063 mm; Weight: 380 kg; DESCRIPTION Heavy-duty professional design with high dead weight for maximum smoothness Particularly smooth and precise running thanks to torsion-free machine housing Large-sized cast iron saw table made of one piece, swivels from 0Â to +45Â with ground and polished surface Patented table tilting device with handwheel and rack Saw band quick tension Precision Saw Band Roller Guide Fast and precise cutting height adjustment via handwheel and rack with millimeter scale safety switch for automatic switch-off when the door is opened Large cast iron ...

Intermediate flange butterfly valve, butterfly valve, with pneumatic rotary actuator DANFOSS SOCLA KLZ 100/16 BAB P FS DN100, PN16 Material ( Housing ): Cast iron ( JL-1040 ) Material ( gasket ): NBR Material ( washer ): Ductile iron ( JS-1030 ) Control pressure: 6 - 8 bar Installation length: 52 mm New ! Dimensions: 440 x 215 x 155 mm

Current meter with current transformer and rotary iron instrument PHOENIX CONTACT, KWK, GOSSEN Measuring range: 0 - 600 A AC ( 0-600AAC ) Current transformer: KWK S 40 b Primary current: 600 A Secondary current: 5 A 50 / 60 Hz Turning iron instrument: GOSSEN 600 / 5 A Conductor rail and terminals: PHOENIX CONTACT Type UHV 240 used ! Dimensions: 400 x 100 x 140 mm

For electric motors, transformers and alternator stators and allows to separate copper, aluminum and iron. We can offer 3 versions of this machine :, 1) Horizontal extractor to remove the Copper ring rotors with Ø 40 to 240 mm., 4,5 kw installed power, weight 1.000 kg, oil tank 50 lt., Dimensions 1,5 x 1,0 x 2,5 mt. LxWxH, Euro 18.000, 2) Horizontal extractor + Splitting knife to split the motor outer casing (usually AL or Cast Iron) and cutting the stators in 2 halves to extract Copper, 11 kw installed power, weight 1.100 kg, oil tank 50 lt., Dimensions 1,5 x 1,0 x 2,5 mt. LxWxH, Euro 32.500, 3) Horizontal extractor (1) + Splitting knife (2) + Vertical extractor that can extract copper from rotors up to 500 mm Ø and stronger rotors with the help of hydraulic pliers., 11 kw installed power, weight 1.250 kg, oil tank 50 lt., Dimensions 1,5 x 1,0 x 2,5 mt. LxWxH, Euro 38.000, Video avail ...

x-travel: 950 mm y-travel: 400 mm z-travel: 500 mm tool taper: ISO 50 throat: 510 mm quill stroke: 105 mm spindle turning speed range: 18 - 1800 U/min feeds: 16 - 627 mm/min rapid traverse: 1670 mm/min table-size: 1400 x 400 mm table load capacity: 500 kg T-slots: 3x14x100 mm distance spindle /table: 150 - 650 mm engine output: 9,0 kW weight: 3660 kg dimensions of the machine ca.: 2290 x 1770 x 2120 mm current new price approx. 60.000 euros Special price on request The heavy universal bed milling machine offers wide guides and high Drive power for superior cutting performance and is with your Extensive equipment ideal for plant and mechanical engineering suitable. The heavy vertical milling head can be swiveled right and left, The quill can be moved manually and the spindle speed can be adjusted continuously regulate. The feed in the Y and X axes can be done via a robust Manual transmi ...

spindle tilting: + 45,5° bis -45,5° ; height adjustment: electrically; tilting adjustment: electrically; fence adjustment: electrically ; altitude display: digital; swivel angel display: digital; fence display: digital; spindle: MK 5; speeds: stepless 900 †12000min¯¹; power consuption: 7,5 kw; motor brake: yes, automatically; suction connection: 3 x 100 mm, 1 x 120 mm; machine length: 2540 mm; machine width: 1195 mm; weight: 950 kg; Highly stable steel gray cast iron construction Large work table made of gray cast iron Electric spindle drive 7.5 kW with maintenance-free direct drive guarantees maximum precision through maximum smoothness Maximum power is already available from 3400 min¹ Precision aggregates and high own weight Rapid table insert, infinitely manually adjustable to tool diameter (optionally electronically positionable) Standard with righ ...

Wentzky 4R150 (Graessner), lapping machine, dia mm 1500, 4 rings (I.D. 535 mm), This machine can be inspected under power in our warehouse Test run possible Mimu Machine Tools Gussago BS Italy, Lapping is a [machining](https://en.wikipedia.org/wiki/Machining) process in which two surfaces are rubbed together with an [abrasive](https://en.wikipedia.org/wiki/Abrasive) between them, by hand movement or using a machine., This can take two forms. The first type of lapping (traditionally called [grinding](https://en.wikipedia.org/wiki/Grinding_machine)), involves rubbing a brittle material such as [glass](https://en.wikipedia.org/wiki/Glass) against a surface such as [iron](https://en.wikipedia.org/wiki/Iron) or glass itself (also known as the lap or grinding tool) with an abrasive such as [aluminum oxide](https://en.wikipedia.org/wiki/Aluminum_oxide), [jewellers rouge](https://en.wikipedia.or ...

Roll diameter: 640 mm; Stand projection: 620 mm; Cutting depth: 400mm; Swivel table: yes -0 to + 15Â; Table size: 870 x 620 mm; Belt speed: 1660m/min; Motor power: 2.2 kW / 400V; Engine braking: yes / automatic; Suction connection: 2 x 120mm; Machine length: 1190 mm; Machine width: 780 mm; Machine height: 2063 mm; Weight: 320 kg; Heavy-duty design with high dead weight for maximum smoothness Particularly smooth and precise running thanks to torsion-resistant machine housing Cast flywheels with rubber lining and cleaning brush 3-roller precision saw blade guide as standard at the top and bottom Large cast iron saw table, swivel from 0Â to +15Â with ground and polished surface Large cast iron rip fence with round rod guide, easily movable Saw band tension indicator Precise cutting height adjustment via rack and pinion with millimeter scale Self-braking motor Available on r ...

Key data: 50 mm, 1500 mm, 1400 mm

Code 231017 Description Radial drilling machine Make MEUSER + CO Model M 50 R Serial No. 39112 Year Capacity in Steel 60 50 mm Capacity in Cast Iron 60 mm Thread cutting in Steel 60 M 45 Thread cutting in Cast Iron M 55 Spindle taper 5 MC Spindle radius: max/min 1700/600 mm Spindle traverse 1100 mm Min / Max height spindle / top of base plate 500 / 1400 mm Arm truss 600 mm Quill stroke 310 mm Number of speeds 18 Spindle speed range 25 – 2000 rpm Number of spindle feeds 14 Spindle feed range 0.06 – 0.80 mm/rev Baseplate size 2400 x 860 mm Clampsurface base plate 1700 x 860 mm Main motor 5 kW - 380 Volts Dimension of machine 2400 x 1100 x 2800 (3100) mm ( L x W x H ) Weight 4070 kg Accessories Box 650 x 500 x500 mm Coolant Hydraulic clamping Conditon Machine is in very good and nice condition

profile bending roll model Femar PF22 year 1985 machine in working condition refurbished mechanical operated motorized electric pinch roll pyramid mechanical operated gear unit motorized electric rolls rotation position bending readout gauge adjustable rollers height to seat and bend the different shape of profiles Capacity ( see chart in enclosed ) angle 120 x13 mm flat bar on edge 120x30 mm flat iron 140x45 mm square iron bar 70 x70 mm T-section 100 mm C-section 160 mm IPE beam 160 mm dimension 2170 x1650 x H 1200 mm 8 ton

Perfecta 115 TS High Speed Guillotine Age: 2009 Cutting table width: 1150 mm TS-Control 19" Touch Screen Colour display Cast-Iron Air table Cast-Iron Side Air Tables (Left and Right) Table Light Cutting line light and preclamp function Accessories: Extra Knives

: neu : ca. 8 Wochen ab Auftragse : Spanien : 23500 € : 481.75 € : 60 to : 500 mm : 5 : 2 : 40x11 mm : 350x10 mm : 120x10 mm : 45/40 mm : 150x10 mm 5 workstations foot pedal trigger hydr. drive flat steel shears incl. Device for reducing the deformation angle iron scissors with round and square bar opening triangle claw punching and bending device for flat iron table at the flat steel and notching station user manual in GERMAN and ENGLISH The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Code: 0262 Brand: VOLPATO Model: LBO 60/G - CE Standard Cast iron belt sanding machine with goose neck - CE Standard Cast iron load-bearing structure Table lenght mm 3500 Table width mm 1100 Vertical stroke mm 680 Motor with 2 speeds Hp 3,5 - 4,5 Belt motor Kw 4,12 Vacuum motor Kw 0,75 Table lift motor Kw 0,37 Overall dimensions : mm 5200 x 1600 x 1600 h Weight kg 680

RAFAMET KCI 320/400N CNC vertical turret lathe manufactured in 2011 in Poland, can perform complex production programmes on large-size workpieces, thanks to one turning head and three milling heads set at different angles. The machine, with its compact frame structure made of high-quality grey cast iron, is distinguished by its high geometric stability, high rigidity and excellent vibration damping. The CNC vertical turret lathe KCI 320/400N performs precision turning, milling, drilling and boring of cylindrical, conical and curved surfaces with the aid of the applied heads. One of them is a special milling head (offset), used to perform drilling and milling operations with the position of the tool axis offset from the spindle axis in a direction parallel to the slide travel plane. On the other hand, the turning head allows to mount CAPTO turning tools in horizontal and vertical socke ...

Working width: 410 mm; Planer shaft: Tersa knife; Number of knives: 4; dressing table length: 2000 mm; Hollow and pointed joint adjustment: no; Dressing stop angle adjustable: yes 45Â to 90Â; maximum clearance thickness planer: 230 mm; Height adjustment thickness table: handwheel; Display of planer thickness: mech. Counter; Feed speed: 6 / 12 m/min; Feed roller: steel; Pull-out roller: steel; Pressure bar: Yes; Table rollers: no; Motor power: 5 kW; Engine braking: yes, automatic; Suction connection: 120mm; Machine length: 2000 mm; Machine width: 750 mm; Weight: 430kg; TERSA planer knife system enables particularly quiet running. Diagonally toothed steel feed roller for constant and uniform material feed material feed with two speeds Numerical display for thickness table height The 2,000 mm long dressing tables allow easy dressing of large workpieces. Work tables ar ...

General SKU411S991 LocationBarneveld MakeGeorg Dietzel (D) TypeEA 630 Main Features MaterialChromed Motor11 KW Surface6.28 m2 Specified Features - Roll dryer Roll dryercheck Double rollcheck Roll surface6,28 m² Roll sizesdia. 1000x2000 mm Steam heatingcheck With knife dischargecheck Motor11 kW, 500 Volt Roll speed2-8 rpm With jacketcheck MaterialCast iron, Cast Iron Hard Chromium, Rubber Information Extra SpecificationsSmall roll: dia. 210x2000 mm, area: 1.3 m², material: 1.1830, rubberized Spare roll Roll dryersGeorg DietzelDryers > Roll dryersBrand > Georg Dietzel What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

Vertical axis grinding machine Mod. VAM RV 800, complete with diamond wheel holder plate (excluding wheel), diam. Mm 420 with abrasive sectors, low voltage electrical system. Automatic descent displayed electronically controlled, allows flattening cycles which include: roughing and finishing passes, flash hiding passes, head lifting at the end of the work cycle at the programmed starting point, recovery of wheel wear in sectors during a work cycle (we recommend the use of self-brightening sectors as the NC does not manage the diamond grinding of the wheel). The descent of the wheelhead is interpolated with the revolutions of the table. Quick for head up and down, automatic mast lubrication. 22.5 kw (HP 30) electrospindle, equipped with precision bearings with automatic play recovery. INVERTER for grinding wheel electro-spindle speed adjustment, display of rpm and motor absorptio ...

Iron cylinder. Induction-hardened rollers. Easy handling thanks to mobile control panel with pushbuttons. Conical bending device. Hot-rolled steel rolls SAE 1050 (CK 45). Main motor with braking system. Precision bending with brake motor. Wire grooves at roll ends. Spheroidal cast-iron main frames. Upper and lower rollers driven by a single gearbox and gear system (RM). Steel rollers with SAE 1050 quality certificate and high tensile strength. Built to CE safety standards

combined bending machine-straightening press, profile bending machine, bending machine, flat iron bender, horizontal bending/straightening press, horizontal bending machine -Flat iron bender: hydraulic profile bending machine -Pressure capacity: 140 Ton. -Stroke cylinder: 455 mm -Counter bearing max width: 1250 mm -Support rollers: height adjustable 250 mm -Dimension: 2060/3735/H1620 mm -Weight: 8300kg

Type: VSP 50 CNC Parameters: 11750 mm, 2000 mm Manufacturer: Tos Description: The machine is in good technical condition, after agreement the possibility of testing. Main dimensions maximum and smallest distance of the spindle axis from the stand guide: -version without tool magazine 2500/500 mm -version with tool magazine 2500/600 mm maximum and smallest spindle end distance: -from bed guide 1480/380 mm -from the base of the machine 1860/760 mm headstock adjustment 2000 mm adjustment of the headstock on a machine with a tool magazine 1900 mm arm adjustment 800 mm Sleigh adjustment: -version with one bed 1000 mm -version with two beds 4500 mm -version with three beds 8000 mm -version with four beds 11500 mm Maximum drilling diameters: diameter of drilling fully into steel with a strength of 600 MPa 50 mm diameter of drilling completely into cast iron with a strength o ...

cutting diameter: 500 mm capacity 90 degrees: flat: 800 x 500 mm capacity 90 degrees: square: 500 x 500 mm capacity 45 degrees: round: 500 mm capacity 45 degrees: flat: 530 x 500 mm capacity 45 degrees: square: 500 x 500 mm capacity 60 degrees: round: 350 mm capacity 60 degrees: flat: 350 x 500 mm capacity 60 degrees: square: 350 x 350 mm saw band length: 7050 x 54 x 1,3 mm vice: 500 x 800 mm cutting speed: 15 - 100 m/min coolant tank: 30.0 Liter Control: JAESPA NC height of material-table: 700 mm total power requirement: 9.5 kW weight: 3000 kg range L-W-H: 3200 x 3500 x 2360 mm maintained condition () current new price approx. 90.000 euros Special price on request Fully automatic, NC controlled 2-column band saw machine, for one-sided Miter cuts up to 60 degrees, for industrial use For sawing off solid material, pipes and profiles made of steel and cast iron as well as light and non- ...

MP BLOWN FILM EXTRUDER EBHD 80, for HDPE and LDPE, constructed in 2005, excellent conditions, Barrel Screw: Φ80 mm with mixing zone LD 28/1 nitride hard chromium steel, Barrel heating zones: 4 zones thermal power 4 KW each plus 1 filter thermal zone 4 KW., Screw Length (L/D) : 28/1, Screw Diameter (mm): 80, Screw Speed (R.P.M.) : 65, Cylinder Total Heating (KW): 16, Flange Heating (KW): 4, Number of Die Heating Zones: 3, Die Total Heating (KW): 6,6, Cylinder Cooling: 4 separates fan motors for each individual thermal zone, Cylinder Cooling Power (KW): 3,5, Installed Electric Power (KW): 70, Max Output (KG/H): LDPE 100 Kg/H, HDPE 90 Kg/h, Film Width: (Min-Max) 280 mm – 1000 mm, Film Thickness: (Min-Max) 0,018-0,200 mm, Main Driving Gear Reducer: Monobloc Reducer Italy Made ROSSI SPA”, Main Motor: AC 3 Phase Inductance Motor 30 KW (40 HP)., Main Motor Control Driving: (VFD Inverter MI ...

Turning length: 1200 mm Center height: 135 mm Suitable for: - Iron works - Wrought iron curls - Bend chop Equipped with: - Various bending workpieces - Miscellaneous Aids -Operating instructions Country of origin: Spain Engine power: 2 hp Machine LxWxH: 186 x 55 x 126 cm Machine weight: 400 kg

Description: SPECIFICATIONS Character: Haeusler Type: HPR 10 Coker round: 89x5 mm - diameter 600 mm Solid round: 65 mm - diameter 600 mm Solid square: 50x50 mm - diameter 500 mm Solid rectangle difficult side: 90x15x10 mm - diameter 900 mm Corner iron outside: 90x90x11 mm - diameter 900 mm Angle iron inside: 70x70x10 mm - diameter 900 mm T-profile outer edge: 100x100x11 mm - diameter 1,000 mm T-profile inside edge: 70x70x10 mm - diameter 900 mm weight approx.: 2,000 kg, Approx. Onsite Dimension. (l x w x h): 1,300 x 1,400 x 1,800 mm

Axis diameter: 95 double T-iron on the x-axis: mm U-iron on the x-axis: mm T - beam - web outwards: mm channels - flange: angle steel/side length: mm square bar steel: mm peripheral speed: m/min total power requirement: KW weight of the machine ca.: 3,5 t dimensions of the machine ca.: 1,6 x 1,5 x ,9 m Profile bending machine with: - 3 driven axles - Box with tools - Emergency stop facility The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Technical data approx.: -Mot. Driven Upper Roller -Manual. Infeed of the middle roller - Both lower rollers can be adjusted horizontally - Shaft diameter approx. 60 mm - Effective shaft length approx. 120 mm - Working speed in one stage - Bending capacity approx. : - - L. and T – iron outside at R 1200 mm 70 x 7 mm - - L – Iron Inner R 1200 mm 75 x 10 mm - - Flat bar flat R 450 mm 100 x 15 mm - - Flat bar upright R 700 mm 60 x 10 mm - - Square bar R 450 mm 30 x 30 mm - - Tubes with special tool R 900 mm 50 x 5 mm -with: - Standard bending roller set - Drive 400 V / 3 kW - Weight approx. 1200 kg - Space requirement approx. W 900 x H 1500 x D 1200 mm

Description: Wide finishing cutter of the Kennametal brand Diameter: Ø 200 mm Suitable for fine machining of cast iron and cast iron with nodular graphite. Features perfect axial run-out without adjustment of the insert. High-precision insert seat for outstanding surface quality and evenness. Easy handling and cost-effective set-up of the milling machine.  , Approx. Onsite Dimension. (l x w x h): 200 x 200 x 80 mm, weight approx.: 10 kg

Briquette diameter: mm 180, Briquette diameter large mm 195, Force main cylinder kN 8,500, Briquette density steel, cast iron Kg/dm 5,5, Briquette density aluminium Kg/dm3 2,4, Briquette density brass, copper Kg/dm3 7.0, Capacity steel/cast iron t/h 7.5, Capacity aluminium t/h 3.5, Capacity brass/copper t/h 8.0, Drive power standard kW 180, Footprint m x m 6.5 x 8.5, Machine weight t 45, Year: 1999, Immediately available, Briquette diameter: mm 180, Year: 1999

Description: No.1 'HS 12 H Serial No.2337' - Automatic machine for straightening and cutting round metal wires smooth and ribbed from mm. 4 to 12, with hydraulic and flying shear cutting: with straightening system with 3-speed rotating body, obtainable by selecting the stepped pulley: with electric motor of 22KW, with soft starter for smooth starting, with 6 pairs of conveyor rollers, pressure pneumatic, for a forward speed of 30/150 mt./min., with hydraulic power unit with oil accumulation with 5.5 KW motor for fast and precise cutting. Complete with 2 sets of straightening units for quick change of cast iron jaws, set of conveyor rollers from mm. 4 to 12 and pre-selection piece counter.  Mt. 4 pallet  Nr. 1 FS-type decoiler, bell carrier with pneumatic and hand brake  Nr. 1 Bell for rolls of int. diam. Of cm. 44/78  Nr. 2 straightening units each complete with 3 cast iron j ...

Description: Flat steel scissors: Knife length: 220 mm Sheets up to: 11 mm Flat steel up to: 120 x 13 mm Profile steel scissors: Angle iron up to: 80 x 8 mm T-iron up to: 80 x 8 mm U and I steel up to: 120 mm Number of strokes: approx. 55 / min. Steel bar shears: Round steel up to: 32 mm Square steel up to: 30 mm Notcher: Sheets up to: 10 mm Latch width up to: 40 mm Latch depth up to: 80 mm Hole punch: Punching capacity: approx. 35 t = 25 Ø x 11 mm / 20 Ø x 13 mm Approx. Onsite Dimension. (l x w x h): 800 x 1,250 x 1,800 mm, weight approx.: 900 kg

C-shaped screw clamp, screw clamps, steel construction clamps, clamps, clamping tools, malleable cast iron screw clamp -Manufacturer: Holex, malleable cast iron screw clamp 300 x 140 mm -Wingspan: approx. 300 mm -Clamping depth: approx. 140 mm -Number: 2x screw clamp available -Price per piece -Dimensions: 400/210/H40 mm -Weight: 2.1 kg/piece

C-shaped screw clamp, screw clamps, steel construction clamps, clamps, clamping tools, malleable cast iron screw clamp -Manufacturer: Holex, malleable cast iron screw clamp 250 x 120 mm -Wingspan: approx. 250 mm -Clamping depth: approx. 120 mm -Quantity: 1x screw clamp available -Dimensions: 340/180/H30 mm -Weight: 1.5 kg.

x-travel:2300 mm y-travel:2000 mm z-travel:1000 mm table-size:2300 x 1600 mm T-slot (width-distance-quantity):8x 22 x 180 mm max. table load:8 t distance between columns:1840 mm distance spindle nose and table:180~1180 mm spindle drive:22/46 kW max. torque on the spindle:140.1/286.5 Nm (S6-25%) spindle nose:50 SK spindle speed:10000 (direkt) U/min rapid traverse X,Y:20000 mm/min. rapid traverse Z-axis:15000 mm/min milling feed range:1~10000 mm/min Machine size (LxWxH):7027 x 5217 x 4339 mm total power requirement:60 kva weight of the machine ca.:25 t positioning accuracy:0,020 (gem. VDI/DGQ3441) mm repeating accuracy:0,015 (gem. VDI/DGQ3441) mm CNC controller:Heidenhain TNC 620 automatic tool changer:Optional gear box:BF Getriebe (optional) chip conveyor with chip bucket:2 Stk. Spirale, 1 Stk. Scharnierband inner coolant:20 bar CE-design:vom TUEV Used Milling Machine KRAFT VM-3218 with ...

Swivel spindle milling machine Brand: Panhans type: 245/200 New machine Solid 880 kg machine with smart control system - Infinitely variable speed regulation 1500 - 10,000 rpm, - 7.5 kW motor with 11 kW frequency converter - Pushbutton with electronic soft start 7 touch control, optional use, top and bottom - Cutter zero point selectable in program, 3 reference points - Simple operating menu through innovative touch control (max. 2 levels) - Operating hours counter - Warning messages in case of operating errors - Remote maintenance via Internet (VPN tunnel) - USB interface for data backup and import of tools, programs and users - Tool database for 5 tools (20 programs are possible per tool) - 2-axis positioning control for height and swivel adjustment - Electronic position and speed displays Double-sided swiveling, fixed milling spindle for the swiveling range  ...

Sizing saw Brand Panhans Type: 680 / 200 New machine Basic construction - Solid German machine construction - approx. 1150 kg - Machine body manufactured as a stable welded frame construction from strong-walled steel profiles. - The torsion-resistant and finely planed cast iron table top is mounted on the machine body. - The robust and powerful sawing unit built into the machine body is the guarantor for precise saw cuts. - The complete saw shaft unit is dynamically balanced, double-guided swivel segments made of gray cast iron with double column guide for height adjustment as well as the circular saw shaft with 2 ball bearings ensure absolutely smooth running. Supports and stops - The ball bearing-mounted double roller carriage is smooth-running and maintenance-free. Precise and clearance-free running over the full length, guided with hardened and ground prismatic guides ...

Type: Pipeline Model 63, magnet separator for removing iron from ceramic chippings etc., input: 380/220/115 V, output: 24 V / 7.5 A (transformer built-in), 2.4 to./h.

Pipeline Model 63; Magnet separator for eliminating iron contamination in ceramic and other slurries. Trafo input: 380/220/115 Volts, Output: 24 Volts / 7,5 A

Storage tank, storage tank, fuel oil tank, diesel filling station, yard filling station consisting of: 1 x 30,000 litres capacity storage container 1 x pump type DK-80-MZ Description Containers: according to DIN 6616/D, above ground, double-walled, incl. officially recognized test certificate. The container has two saddle feet, a manhole DN 600 with dome lid, is used, emptied inside and professionally cleaned and is equipped with the following fittings: 1 filling pipe with TW closure (filling cap) and immersion pipe, 1 bearing tube with bearing rod and bearing rod closure, 1 vent pipe with vent hood, 1 brand new limit sensor with type approval (AIII), 1 ladder and 1 spare sleeve for picking purposes, 1 optical leak detector with type approval and leakliquid. The container is re-primed on the outside and painted in ral 7011 - iron grey. Other colours ...

Manufacturer: GORBREX Model: TKV 532 CNC New in: 2015 Control: SIEMENS SINUMERIK 828 Machine fully modernized and modified of SEDIN 1L532 with new electrical and lubrication unit, painted, replacement of damaged mechanical parts, with possibility of upgrading. The upgrade is made of cast iron, on request we can equip the machine with the new CNC control SIEMENS SINUMERIK 840. Delivery time: max. to 3 - 4 months Technical details Number of columns: 2 Number of carriages: 1-option 2 Type of carriage: Ram Number of axis controlled: X/Z option X1/Z1,C Max. turning diameter: 3200 mm Table diameter: 2800 mm Max workpiece height: 1600 mm with possibility of upgrading up to 2200 mm Max table load: 16 000 kg Range of table speeds: 70 rpm Number of table speeds ranges: 3 Vertical travel in Z axis( ram travel): 1200 mm Horizontal travel of carriage in X axis: 1720 mm Working ...

Crosscut and miter saws with maximum cutting height of 200 mm stable grey cast iron construction precise ball bushing guide of the tool slide on hardened and ground steel shafts Manual saw feed fast up to 65 ° horizontal MITRE setting and 60 ° vertical for adjustable fixed stops lower blade guard to extractor can be connected Machine mounted on mobile machine base with 1,5 mtr. long rollers left and right left side with scale and stop position slider Technical data: Engine: 400 V / 5.0 kW Speed: 2800 RPM Cutting length: 420 mm (at 90 °) Cutting height: 200 mm (at 90 °) Miter range horizontal: 45°-90° - 20 ° Miter range vertical: 60° - 90°-30° Saw blade diameter: 520 mm Dust nozzle: 100 mm Weight: 490 kg

Workspace tip height 102 mm centre distance - with normal headstock with 450 mm - reduction gear headstock 375 mm - over the cheek 200 mm - over the slide 120 mm spindle poles spindle nose for collets type Schaublin W25 spindle bore 25 mm collets passage 20 mm reduction ratio of 1:5 Raedergetriebes cheek height x width x length 168 x 130 x 1000 mm cheek from cast iron, trapezoidal profile as lathe 102 N and dovetail, hardened and ground. Sledge greatest way on the cheek width 400 mm runner - length 90 mm top runner above 80 194 mm way manual adjustment 20 mm shank of tools 12 x 12 mm cross slide width length 94 300 mm way manual adjustment 100 mm bed slide length of leadership on the cheek 250 mm screw lead screw for longitudinal turning and threading, Ø 40 mm screw hardened, Ground thread, slope 4 mm speed range RPM 270 3000 rpm turning 0.02 0.3 mm / Rev. Tapping largest slope  ...

Pneumatic valve DN 300 Manufacturer: Jaudt Dosiertechnik Maschinenfabrik GmbH Type: Varioschieber FSV Opening width mm: ø 350 Height mm: 130 Max.Working temp. ° C: 80 Operating pressure MPa: 0.6-1.0 maximum operating pressure MPa: 0 Control voltage V: -. Housing: one-piece cast housing in flange version the round face with coarse good Chicane Sealing: slide sheet implementation for with Adjustable stuffing seal Pressure piece from cast aluminium alloy Blade: Stainless steel 1.4301 Slide sheet: eccentric screws galvanized Finish: Stainless steel and aluminum parts blank Grey cast iron housing painted in RAL 9006 Steel parts zinc plated, 10 & #956; m Plate made of aluminium Housing material: Cast aluminium alloy (AlSi 10 mg) shock-proof up to 5 bar Flanschbohrbild: According to DIN 2501 PN 6 Packing material: ARAMIDE (Tmax 280 ° C) Operation: pneu ...

1 x NEW 'Bainite' (India) Make 1000mm (42in) wide x 400mm (16in) dia two roll mill, Hydraulic nip adjustment (dual acting cylinders), Peripherally drilled chilled cast iron rolls (Hardness 65/72 Shore), with anti friction roller bearings, Friction ratio 1:1.08, Hinged guide plates, Lubrication system comprising pneumatic intensifier with grease reservoir, Electro pneumatic brake with power fail safe mechanism. Safety bars fitted to front and rear. Compact right angle drive with 45kW Siemens AC variable speed squirrel cage motor through heavy duty helical design direct drive reduction gearbox (SF 2), Back roll speed 18rpm/front roll 16.6rpm. All mounted on a compact design fabricated steel bedplate. Stainless steel tray underneath. Including electrical controls comprising Siemens G130 VFD drive and S7-1200 plc with HMI. CE marked, with full Technical file, Documentation and S ...

Diesel tank, steel tank, fuel oil tank, tank system, storage tank with 50,000 litres capacity according to DIN 6616/D, above ground, double-walled, incl. officially recognized test certificate. The container has two saddle feet, a manhole DN 600 with dome lid, is used, emptied inside and professionally cleaned and is equipped with the following fittings: 1 filling pipe with TW closure (filling cap) and immersion pipe, 1 bearing tube with bearing rod and bearing rod closure, 1 vent pipe with vent hood, 1 brand new limit sensor with type approval (AIII), 1 ladder and 1 spare sleeve for picking purposes, 1 optical leak detector with type approval and leakliquid. In this example, the tank was painted in ruby red. The container is re-primed on the outside and painted in ral 7011 - iron grey. Other colours at no extra charge: RAL 6005 - moss green, RAL 5011  ...

Standard equipment Manual heavy duty band saw machine with hydraulic Sawframe reduction for miter cuts from 45 ° left to right 65° Saw frame made of sturdy cast iron construction Massive round table Oil bath gearbox consisting of bronze wheel with hardened and ground steel worm Carbide Guide and adjustable roller bearings Quick clamping Vice with additional quick adjustment and quick release lever Electric high-performance Coolant pump Mechanical blade tension with electric blade monitoring Control tool Free delivery including packaging

Downpour record Grey iron GGG50 1500 x 1500 chamber filter records Downpour records for chamber filter pressing 1500x1500 we can offer to you for almost all arrangements chamber filter records also in PP, filter cloths and spare parts almost all manufacturer.

Wood Turning Lathe Precision device for professional users, with grey cast iron variable speed control high degree of spindle concentricity Spindle can be fixed all 15° LCD speedometer One hand operation of the tailstock and tool rest with quick-release mechanism Voltage: 230V / 50 Hz Engine power: 735W (S1 100%) Tip height: 160 mm Top width: 510 mm Speed ranges: 250-750 m-1, 550-1650 min-1, 1300-3850 min-1 Spindle stock rotation: 180 degrees Headstock thread: M33 DIN800 Morsekonusaufnahme: MK2 / MT2 Quill stroke: 63 mm Weight: 52 kg Dimensions: 1035 x 305 x 449 mm G & HM-D510F

HOT IRON OSCILLATING SAW & OIL HYDRAULIC FEEDING CONTROL SYSTEM

Specifications / Technical data S-1400/T 3-axis CNC-portal-machine and engraving machine (Attention: Pictures show the High-Z S-1400 with trapezoidal thread spindles, this differs exclusively by the spindles . With the T-variant of the high-Z CNC fraes machine, you acquire old-fashioned technology with the certain I-meat in TUeV-certified quality (EMC). The High-Z/T is designed for even more accuracy (repeatability about 0.01mm ) and especially for higher travel speeds. Through the ball-circulation spindles used, the High-Z/T portalfraes machine achieves fantastic accuracy and an almost unmeasurable reverse play of about 0.01mm. At the same time, high travel speeds of up to approx. 108mm / second ( 6500 mm / minute ) can be achieved. This means engraving and fraes speeds of up to approx. 4500mm/min can be realized and urgent journeys up to approx. 7000mm/min. Here you can s ...

Woodturning machine DB 1100 new 230 V 0.75 kW 50 Hz Top distance of 1100 mm Tip height 179 mm Machine bed, base, tailstock made of cast iron Speed control of 500-2000 RPM MK2/M33 Spindle stock 90 ° swiveling ideal for large diameter! Weight 92 kg G & pieces 5921100