134,065 used machines on RESALE, but how to find them? Machine Search
A Karstens cylindrical grinding machine from 1992, which was completely overhauled and modernized in 2014, is available. Center width: 1000mm, center height: 180mm, grinding diameter: 360mm, max. workpiece weight center/flying: 250kg/70kg, grinding wheel diameter: 400mm. Spindle holder: MK4, speed: 450rpm, swivel range: 90°, quill holder: MK4, quill stroke: 45mm, quill force: 600N. Table swivel: 10°, infeed spindle: 80mm, rapid traverse: 50mm, coarse adjustment: 280mm, weight: approx. 3800kg. Including 3x centering points and grinding wheels as good as new. Documentation available. On-site inspection is possible.
Center height: 135mm, max. sanding length (shaft): 500mm, max. sanding diameter: 270mm, sanding wheel diameter: 400mm, power requirement: 7.5kW, machine dimensions X/Y/Z: approx. 2000mm/1300mm/1300mm, weight: approx. 1700kg.
Surface grinding machine ELB type SW 3 HA JuwelMasch. No. 51810465 year of construction 1965Grinding area 300 x 150 mmClamping surface 300 x 150 mmElectromagnet 300 x 150 mmDistance spindle center - magnet approx. 350 mmGrinding wheel diameter 175 mmGrinding wheel width max. 25 mmGrinding wheel speed 2800 rpm. Grinding spindle drive 0.75 kWNetz connection 380 volts, 50 Hz.- manual and automatic table - transverse adjustment (0.02 mm per graduation) - manual transverse adjustment via handwheel, travel distance per handwheel revolution, Y -
Sanding length: 500mm, sanding width: 200mm, max. workpiece height: 250mm, table dimensions X/Y: 600mm/200mm, sanding wheel diameter: 225mm, sanding wheel width: 25mm, sanding wheel bore: 51mm, speed: 4200rpm, machine weight: approx. 2500kg. On-site inspection is possible.
Grinding wheel diameter: 220mm, grinding wheel width: 5mm, base body width: 20mm, bore diameter: 52mm. Test piece: diameter: 100mm, width: 300mm, profile height: 35mm. Small workpiece: Outer diameter: 400mm, bore diameter: 205mm, wheel width: 100mm, torque: 20Nm, weight including mandrel: 200kg. Large workpieces: Outer diameter: 700mm, bore diameter: 350mm, disk width: 300mm, torque: 800Nm, weight: 250kg. Accuracy: Repeat accuracy: less than 2µm, axial and radial run-out accuracy (large spindle): less than 2µm at 400mm diameter, axial and radial run-out accuracy (small spindle): less than 2µm at 200mm diameter, parallelism over 300mm between test piece and workpiece axis: less than 2µm. Tool spindle speed: 10000rpm, small workpiece spindle: 23000rpm, large workpiece spindle: 6000rpm, test piece spindle: 1000rpm.
Table dimensions X/Y: 600mm/200mm, grinding dimensions X/Y: 600mm/250mm, magnet dimensions X/Y: 600mm/200mm, grinding wheel diameter: 225mm, grinding wheel width: 25mm, grinding wheel bore: 51mm, spindle center-to-table distance: 350mm (+/-50mm), table feed: 20m/min, creep speed: 0mm/500mm/min, speed: 4200rpm, machine dimensions X/Y/Z: approx. 2700mm/2100mm/2100mm, weight: approx. 2500kg. On-site inspection is possible.
A total of four WMW/Werkö saw grinding machines are available. Saw blade diameter min./max.: 250mm/1450mm, grinding wheel diameter: 250mm, speed: 2500rpm, tooth pitch: 42mm, grinding spindle swivel range: +/-45°, machine dimensions X/Y/Z: approx. 850mm/1000mm/1800mm, weight: approx. 1100kg. Documentation available. On-site inspection is possible.
A CNC cylindrical grinding machine GP Basis Karstens with rotating grinding headstock is available. Grinding length: 650mm, center height: 250mm, workhead: MK4, tailstock: MK4, wheel diameter: 400mm, spindle diameter: 80mm, sleeve length: 250mm, speed: 3000rpm, spindle power: 1.5kW, control: Siemens and Balance System VM25. Documentation available. On-site inspection is possible.
Sanding length: 700mm, sanding width: 330mm, max. workpiece height: 450mm, table dimensions X/Y: 280mm/600mm, table speed: 25m/min, sanding wheel dimensions: 305mm/25mm/76.2mm, spindle power: 3PS, machine dimensions X/Y/Z: approx. 2100mm/1600mm/2000mm, weight: approx. 2000kg. Documentation available. On-site inspection is possible.
A CNC 5-axis grinding machine SMP is available. Grinding wheel diameter: 200mm, max. tool diameter: 150mm, max. tool length manual/automatic: 300mm/140mm, max. workpiece weight: 25kg, spindle speed: 20000rpm, spindle power: 7kW, interchangeable magazine: 4 places. Documentation available. On-site inspection is possible.
grinding length: 600 mm grinding width: 205 mm x-travel: 600 mm : ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Axes: 5, max. grinding wheel diameter: 150mm, spindle speed: 9000rpm, workpiece spindle speed: 1500rpm, clamping spindle speed: 13000rpm, travel X/Y/Z: 200mm/190mm/150mm, tool holder: HSK-50, machine dimensions X/Y/Z: approx. 1700mm/1400mm/1800mm, control: NumRoto 1060, control defective. Including coolant pump and coolant tank, grinding wheel set with 12x holders. Documentation available. On-site inspection is possible.
Table dimensions X/Y: 760mm/200mm, max. sanding length: 500mm, max. sanding width: 230mm, table spindle center distance: 520mm, table longitudinal movement: 30m/min, table transverse movement: 16mm/stroke. Grinding wheel diameter: 225mm, grinding wheel width: 25mm, bore: 51mm, power: 5kW. Machine dimensions X/Y/Z: approx. 2500mm/2000mm/1950mm, weight: approx. 2100kg. On-site inspection is possible.
grinding length: 1600 mm centre height: 185 mm diamter spiral cutter: 55mm mm indexing: 4-32 Modul length: 5900 mm width: 2300 mm height: 2000 mm weight: 7 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A Karstens cylindrical grinding machine with display is available. Center height: 180mm, grinding diameter: 360mm, center width: 650mm, max. workpiece weight flying/between centers: 70kg/250kg. Grinding wheel outer diameter: 400mm, face diameter: 250mm, peripheral speed: 35m/s, speed: 450rpm, mounting cone: MK4, quill diameter: 50mm, fine adjustment: 0.08mm. Machine dimensions X/Y: approx. 3250mm/2150mm, weight: approx. 3600kg. On-site inspection is possible.
Center height: 175mm, grinding length: 650mm, B-axis: -15°/195°, workpiece speed: 1750rpm, grinding wheels T1/T2: 500mm/400mm, bore: 203mm, max. workpiece weight: 80kg, workhead: MK4, tailstock: MK3. Machine dimensions X/Y/Z: approx. 3000mm/3000mm/2100mm, weight: approx. 4000kg, operating hours: 56300h, control: GE Fanuc Series 16i-T. Documentation available. On-site inspection is possible. Expected to be available from February/March 2025.
Sanding length: 650mm, max. sanding diameter: 508mm, center height: 125mm, workhead speed: 1500rpm, max. workpiece weight: 30kg, workpiece swivel range: 30°-90°, tailstock: MK3. Grinding wheel diameter: 508mm, grinding wheel width: 40mm, bore: 203mm, max. internal grinding diameter: 150mm. Machine dimensions X/Y/Z: approx. 4300mm/3100mm/2200mm, weight: approx. 4000kg, control: Siemens Sinumerik 820G. Documentation available. On-site inspection is possible. Expected to be available from February/March 2025.
Sanding width: 200mm, sanding length: 600mm, adjustment path X/Y: 690mm/230mm, clamping table spindle center distance: 500mm, sanding wheel diameter: 200mm, sanding wheel width: 20mm, bore: 51mm, table dimensions X/Y: 200mm/600mm, max. table load: 110kp, machine dimensions X/Y/Z: approx. 3000mm/1600mm/2100mm, weight: approx. 1300kg. Documentation available. On-site inspection is possible.
x-travel: 600 mm : ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A conventional precision surface grinding machine with NC control is available. Resolution: 0.001mm, travel X/Y/Z: 1200mm/550mm/400mm, table dimensions X/Y: 1600mm/450mm, table feed: 30m/min, max. table load: 750kg, spindle-table distance: 800mm, Y feed: 180mm/min, Y precision: 0.001mm, Z feed: 1200mm/min, Z precision: 0.3mm, speed: 2800rpm, grinding wheel dimensions X/Y/Z: 400mm/100mm/127mm. Machine dimensions X/Y/Z: approx. 6500mm/3000mm/2500mm, weight: approx. 6700kg. Documentation available. On-site inspection is possible.
magnetic clamping plate: 1400 - 700 mm weight of the machine ca.: 6 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
A centerless cylindrical grinding machine König & Bauer (Koebau) is available. Grinding wheel width: 300mm, max. grinding diameter: 200mm, grinding wheel bore: 305mm. Control wheel width: 300mm, control wheel bore: 127mm, speed: 85rpm, max. workpiece length (plunge grinding): 300mm. Machine dimensions X/Y/Z: approx. 3150mm/2100mm/1850mm, weight: approx. 6000kg. On-site inspection is possible.
grinding length: 750 mm grinding width: 500 mm workpiece height: 500 mm total power requirement: 50 kW weight of the machine ca.: 5000 t Grinding length, max. 750 mm Grinding width, max. 500 mm Cross movement of grinding slide 450 mm Working height under grinding wheel, max. 500 mm Grinding wheel size Æ 400 x 100 mm Grinding wheel speeds, infinitely variable 300-3,000 rpm Table speed, hydr. 0 - 30 m/min Table speed, creep feed 0.02 - 1,000 mm/min Vertical infeed, infinitely variable 0.002 - 0.03 mm/stroke Grinding spindle drive, max. 32 kW Total electrical load, approx. 50 kW - 380 V - 50 Hz Weight approx. 5,000 kg Accessories / Special Features Creep feed: Electro-mechanical feed (but also hydraulic table movement), with digital display, programable by cam limit switches. Infinit ...
grinding wheel diameter: 300 mm table length: 0 mm table width: 0 mm total power requirement: 1,5 kW weight of the machine ca.: 1000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. grinding diameter: 0 mm grinding length: 0 mm workpiece length: 970 mm total power requirement: 12 kW weight of the machine ca.: 5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
workpiece diameter: 320 mm threading length: 300 mm thread pitch: mm total power requirement: 90 kW weight of the machine ca.: 12000 kg dimensions of the machine ca.: m Thread and worm grinder for steering worms The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. width of grinding wheel: 50 mm ratio: 0 max. dia. of grinding wheel: 400 mm total power requirement: 3 kW weight of the machine ca.: 1000 kg dimensions of the machine ca.: m Pre-Dressing Device for Gear Grinding Wheels The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 2500 mm gear width: 1200 mm max. module: 32 min. module: 3 total power requirement: 25 kW weight of the machine ca.: 60 t dimensions of the machine ca.: m Gear , min. / max. 180 / 2,500 mm Module 3 - 32 Helix angle, max. 10 - 35 ° Gear width for straight gears 1,200 mm Stroke length, approx. 100 - 1,200 mm No. of strokes 80 - 350 /min Stroke position adjustable 300 mm Stroke speed 4 - 40 mm Max. weight of workpiece, approx. 18,000 kg Min. / max. no. of teeth 16 / 576 Table size x bore 1,400 x 500 mm Grinding wheel Ø, approx. 500 mm Grinding wheel peripheral speed 34 m/s Total electrical load, approx. 45 kW - 380 V - 50 Hz Weight of machine, approx. 60,000 kg Accessories / Special Features: Hydrostatic guides in grinding slide, table and in all other guideways. Completely covered working area with sliding doors. Automatic grinding process for various cycles, with ...
max. wheel diameter: 1010 mm gear width: 0 mm max. module: min. module: total power requirement: 15 kW weight of the machine ca.: 9,5 t dimensions of the machine ca.: m Max. depth of tooth 10 mm Max. workpiece Ø (for clearance) 1,010 mm Max. external Ø of coupling 610 mm Sliding base withdraw 216 mm Max. distance from grinding wheel to workpiece nose 90 - 430 mm Max. weight of workpiece, including clamp 500 kg No. of teeth 32 to 150 Grinding wheel Ø, approx 152 - 320 mm Grinding wheel speeds, infinitely variable 0 - 3,600 rpm Work spindle bore 60 mm Total electrical load, approx. 15 kW - 380 V - 50 Hz Weight, approx. 9,500 kg Accessories / Special Features Automatic roughing and finishing process via pre-settable counter and built-in feed cam. Counter for number of teeth. Counter for number of dressing cycles. 2 built-on dressing units with three dressing diamonds for radiu ...
thread dia.: 254 mm grinding length: 350 mm thread pitch: 51 mm Control: SIEMENS S 8 total power requirement: 12 kW weight of the machine ca.: 5000 kg dimensions of the machine ca.: m B A H M Ü L L E R Automatic Internal Thread Grinding Machine Model IPE 12 i.S. Year 1985 Serial No. 103174 _______________________________________________________ workpiece Ø, max. 300 mm workpiece length, approx. 350 mm height of centers (WP spindle/grinding spindle) 300 mm table stroke approx. 450 mm thread diameter ground max. approx. 254 mm thread diameter ground min. approx. 25,4 mm thread length ground in one setting max. 250 mm Lead range, max. 51 mm Lead angle max. 10 ° Total electrical load, approx. 12 kW - 380 V - 50 Hz Weight, approx. 5,000 kg ...
workpiece diameter: 600 mm workpiece weight: 400 kg workpiece height: 300 mm total power requirement: 35 kW weight of the machine ca.: 4500 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding length: 470 mm grinding width: 40 mm workpiece height: 110 mm total power requirement: 1,2 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding height: 60 mm grinding width: 120 mm grinding wheel diameter: 600 mm grinding length: mm workpiece height: 60 mm total power requirement: 50 kW weight of the machine ca.: 7000 kg dimensions of the machine ca.: m D I S K U S (Germany) Double Side Vertical Spindle Surface Grinder, C-Frame Design, with Rotary Workpiece Feeding System and Automatic Dressing Device Model DDS 600 CR-A Year 1969 Serial-No. 6672 ______________________________________________________________________ ________ Grinding wheels Ø x bore, each 600 mm Grinding wheels height x width, approx. 60 mm Workpiece dimensions: Grinding height x grinding width, approx. 60 x 120 mm Vertical adjustment of each grinding head 150 mm External Ø of workpiece carrier disk, approx. 810 mm Feeds of rotary workpiece feed system 1 ...
x-travel: NA mm y-travel: NA mm workpiece height: mm stroke length max.: 450 mm table length: 450 mm table width: 350 mm total power requirement: 1,7 kW weight of the machine ca.: t dimensions of the machine ca.: m Shaper, horizontal,mechanic,vice hydraulic The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding diameter: 360 mm grinding length: 650 mm centre height: 180 mm Control: SIEMENS 840 D total power requirement: 15 kW weight of the machine ca.: 9500 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. grinding diameter: 300 mm grinding length: 500 mm workpiece length: mm Number of axles: 6 St. centre height: 220 mm centre distance: 500 mm x-axis: 500 mm y-axis: 320 mm z-axis: 320 mm total power requirement: 5 kW weight of the machine ca.: t dimensions of the machine ca.: m Height of centres 200 mm Distance between centres / clamping length 750 / 500 mm Table size 290 x 1,600 mm Intermediate table 110 x 1,200 mm X / Y / Z axes 500 / 320 / 320 mm Feed speeds, X, Y & Z axes 0.005 - 5 m/min Grinding head swivelling, vertical axis (B axis) 300 ° Grinding head tilting (C axis) +/- 30 ° Speed range of R axis 0 - 50 rpm Grinding spindle speeds, approx. 5,000 - 10,000 rpm Workpiece holding fixture 50 ISO Indexing 1 - 999 ° Leads 0.5 - 10,000 mm Spindle drive 4 kW Total electrical load, approx. 10 kW - 380 V - 50 Hz Weight, approx. 4,000 kg Accessories / Special Features SCHÜTTE CNC ...
grinding wheel diameter: 300 mm table length: 0 mm table width: mm total power requirement: 11 kW weight of the machine ca.: t dimensions of the machine ca.: m Cut-Off Machine for Hard Materials, Coolant, Hand Lever11 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. grinding diameter: 320 mm grinding length: 500 mm workpiece length: 700 mm total power requirement: 10 kW weight of the machine ca.: 4 t dimensions of the machine ca.: m Height of centres 220 mm Distance between centres / clamping length 750 / 500 mm Table size 290 x 1,600 mm Intermediate table 110 x 1,200 mm X / Y / Z axes 500 / 320 / 320 mm Feed speeds, X, Y & Z axes 0.005 - 5 m/min Grinding head swivelling, vertical axis, manual 200 ° Grinding head tilting, manual +/- 90 ° Speed range of R axis, approx. 0 - 50 rpm Grinding spindle speeds, infinitely variable, approx. 2,000 - 12,000 rpm Workpiece holding fixture 50 ISO Indexing 1 - 999 ° Leads 0.5 - 10,000 mm Spindle drive 4 kW Total electrical load, approx. 10 kW - 380 V - 50 Hz Weight, approx. 4,000 kg Accessories / Special Features SCHÜTTE CNC Continuous Path Control for 4 axes with SIEMENS/BOSCH components and SIEMENS ...
max. wheel diameter: 330 mm gear width: 180 mm max. module: 7 min. module: 0,5 total power requirement: 12 kW weight of the machine ca.: 7500 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 215 mm gear width: 40,65 mm max. module: total power requirement: 20 kW weight of the machine ca.: 10 t Max. external Ø of workpiece 215 mm Tooth profile, height x width 16 x 40.65 mm No. of teeth 5 - 200 Max. tooth ratio 1 : 10 Grinding wheel Ø 51 - 190 mm Grinding wheel speeds 1,000 - 6,000 rpm X Axis (horizontal) 152 mm Y Axis (vertical) 178 mm Z Axis (slide base plate) 304 mm Distance from middle of machine to middle of workspindle 115 mm Axial speed 125 mm/sec Workpiece speeds 0 - 30 rpm Workspindle bore, conical 3 29/32 inch Total electrical load 20 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features FANUC CNC Control, Model 150 MB, for 7 axes, with monitor and direct input. Automatic calculation of all workpiece and grinding parameters. Extensive coolant equipment with filter system, band filter, etc. Driv ...
max. dia. of grinding wheel: 800 mm max. width of grinding wheel: 250 mm grinding table: swivable: Grad total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Double Sided Finegrinder, Dresser, Coolant Device, older M. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding diameter max.: 30 mm regulating wheel width: 12 mm max. width of grinding wheel: mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
max. wheel diameter: 280 mm gear width: 330 mm max. module: 5 min. module: 1 Control: LIEBHERR CNC total power requirement: 28 kW weight of the machine ca.: 12 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
workpiece diameter: 8-125 mm grinding depth: 130 mm clamping length: 50-1100 mm max. workpiece diameter: 0 mm min. workpiece diameter: 0 mm workpiece length: mm total power requirement: 1 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: m T E C H N I C A (Switzerland) Centre Hole Grinding Machine Model ZSM 1000 Year approx. 1975 Serial No. J 1400 _______________________________________________________ Distance between centres 50 – 1,100 mm Height of centres 145 mm Workpiece Ø 8 – 125 mm Max. centre hole taper Ø 2 – 50 mm Max. centre hole taper angle 60 ° Clamping range of vice 4 – 150 mm Stroke of grinding head 130 mm Stroke of grinding tool on workpiece 0.75 – 5 mm Grinding tool Ø ...
workpiece length: 5000 mm swing dia.: 1100 mm clamping length: 6000 mm grinding diameter: 1100 mm grinding wheel diameter: 1300 mm workpiece weight: 2500 kg main drive motor: 22 kW crankshaft bearing diameter: 275 mm steady: 100-250 mm speeds of tool: 400/500 U/min workpiece turning speeds: 20-40 U/min total power requirement: kW weight of the machine ca.: 30 t dimensions of the machine ca.: m 13 Grinding Steady Rests Mandrels Mounting Flanges Clamping Devices The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. Y ...
max. wheel diameter: 0 mm gear width: 120 mm max. module: 3 min. module: 1 total power requirement: 20 kW weight of the machine ca.: 7,5 t dimensions of the machine ca.: m : : : : : : 5 machines in stock, YOM: between 1986 and 1990 Gear Æ, min./max. 55 / 120 mm Gear Æ for shaft-formed parts 80 mm Module (pitch 25.4 - 8.5) 1 - 3 No. of teeth, min./max. 13 / 80 Pressure angle 14 - 30 ° Helix angle, max. 40 ° Workpiece clamping length 145 - 420 mm Grinding worm Æ 300 - 400 mm Grinding worm width 25 - 40 mm Grinding worm speeds, infinitely variable (35 m/s) 1,650 rpm Feed range 0.4 - 4 mm/rev Total electrical load 20 kW - 380 V - 50 Hz Weight 7,500 kg Accessories / Special Features REISHAUE ...
grinding diameter max.: 100 mm regulating wheel width: 200 mm max. width of grinding wheel: 200 mm grinding diameter: 100 mm grinding length: 250 mm feed in: mm working area: mm speed: m/min Bar length: mm total power requirement: 25 kW weight of the machine ca.: 4.500 t dimensions of the machine ca.: m K O E N I G & B A U E R (Germany) Centreless Grinder with Plunge-in Grinding Device Model Multimat 150 - 5 Year approx. 1978 S/Nr. 73 918 _______________________________________________________ Grinding Ø regular/maximal 2 – 50/100 mm Max. length of workpiece for Thru-Feed-grinding 250 mm Max. length of workpiece for plunge-cut grinding 200 mm Grinding wheel size, Ø x width 600 x 200 mm Regulating wheel size, Ø x width 300 x 200 mm Grinding wheel speed, max. 1.450 rpm/35 m/sec. Regulating wh ...
grinding range: 8 - 32 mm sharp cornered angle min./max.: 90 - 140 Grad connected load: 230 V weight of the machine ca.: 16 Kg dimensions of the machine ca.: 0,43 x 0,24 x 0,24 m Drill grinding machine: Additional station for grinding back the drilling cutting surface (clearance angle) 25tk. Collets ER 40 are included in the scope of delivery, these are also suitable for clamping intermediate sizes. For grinding twist drills made of HSS and Hard metals with a TiN layer of 8 - 32 mm. Rotor with precision ball bearings guarantees smooth running. Vibration-free running thanks to its heavy weight and rubber feet. Sharpening angle adjustable for all common twist drills. Package dimensions: 430 x 240 x 240mm. Weight 16kg. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
grinding range: 2 - 13 mm sharp cornered angle min./max.: 90 - 140 Grad connected load: 230 V weight of the machine ca.: 10 Kg dimensions of the machine ca.: 0,35 x 0,2 x 0,2 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
maximum number of results exceeded
please refine your search
