internal grinding si used for sale

1.000 litre, Stock number: T2294, Litre: 1.000, Material: Stainless steel AISI 304, In stock: Yes, Amount in stock: 1 pc., Item: Silo, Standing: 3 pcs. legs, Top: Open with strengthening ring, Bottom: Conical, Inner diameter: Ø 950 mm., Total height: 3550 mm., Other: Screw outlet in the bottom

Grinding wheel dimensions (od x id x width): 508 x 304,8 x 254 mm, Ø min/max to be ground: 1,5 / 120 mm, Width of regulating wheel: 254 mm , Number of regulating wheel speeds: infinite, Min/max speed of regulating wheel (r.p.m.): 10/250 rpm, Dimensions of regulating wheel (od x id x width): 305 x 190,5 x 254 mm, Grinding wheel width: 254 mm, Maximum length to grind in plongeé: 254 mm, Hydraulic motor power: 0,55 kW, Total power: 27 kW, Voltage: 220/380 V, Length: 2.300 mm, Width: 1.885 mm, Height: 1,900 mm , Weight: 6,420 kg

SINGLE SHAFT SHREDDER, V Rotor width 1.500 mm. Rotor diameter 500 mm 16.69″ Motor power 90 kW n.82 knives 60 x 60, adjustable counter-knife, off-set rotor bearings (low maintenance), V-Rotor with knife pockets, Welded knife holders with screwed knives and covered bold heads, Offset rotor bearings ( low-maintenance / closed ), Fast hydraulic backwards incl. different settings by PLC control and anti shock valve, Shredding room unpainted, Movable screen basket (electro-hydraulically), Screen thickness 10mm, Hydrodynamic starting clutch (energy saving system for machine start), Electromechanical drive with heavy duty gearbox, Control cabinet incl. 5m cable, Electrical control system Siemens S7 PLC control, Reverse counter and transmission limit switch (safety package), Star delta starter, Universal joints for piston with ram impulse and load-related ram function, Machine frame on anti - v ...

PVC PROFILE EXTRUSION LINE EVC BRAND, single screw extruder with 60 mm 28 LD, constructed in 1998, for 180 mm max width, 44 kw drive, control panel, Calibrating desk 3,7 m.long with 1 x 9 kw.pump, Caterpillar pull off unit, 180 mm wide, saw, 6,0 mt.long discharging table.

SINK-FLOAT SEPARATION TANK for PLASTIC SCRAPS, Constructed in thick AISI 304 STAINLESS STEEL with reinforced plates and profiles, Dimensions 5,0 X 2,4 mt., Inlet hopper for shredded plastics, Flanged water in/out ports, taps and ball valves, n.2 x 1,5 kw.driven rollers for material movement with Bonfiglioli gearboxes, n.1 chain conveyor on bottom to extract the sunk materials, n.1 diagonal stainless steel chain conveyor, collection drained auger for extraction of floating material, size: 5,0 x 2,4 mt., capacity: 800-1.500 kg/h depending on materials

Constructed according to the high Italian quality standards, Made in sturdy carbon steel welded structure Flat bottom with horizontal screw and doctor blade, or conical bottom with diagonal screw (depending on project requirements) plexiglass inspection window, Electric motor bespoke to project material and size paddle type minimum level indicator Bolted inspection door, Safety devices, CE compliance, drawings, user manual, Can be integrated with our [DRYING SYSTEM](.germanplast.eu/listings/4115725-drying-system-for-vertical-mi xers), price options: size and shape bespoke to project

Weinig Unimat 500 four-sided planer Working width 230mm Working height 140mm Number of spindles 5 Spindle system: Bottom 5.5kw Rights Left 7.5kw Top 11kw Bottom 5.5kw Feed speed adjustable by inverter up to 30m/min Feed motor 4kw Drive on cardan shafts Pneumatic clamps 3 axes controlled from the panel (width, height, pressure position) Worktop air cushions Input table length 2470mm CE Certified DTR documentation

Weinig Unimat 500 four-sided planer Working width 230mm Working height 140mm Number of spindles 5 Spindle system: Bottom 5.5kw Rights Left 7.5kw Top 11kw Bottom 5.5kw Feed speed adjustable by inverter up to 30m/min Feed motor 4kw Drive on cardan shafts Pneumatic clamps 3 axes controlled from the panel (width, height, pressure position) Worktop air cushions Input table length 2470mm CE Certified DTR documentation

hydraulic: ja : 100 t weight of the machine ca.: 2,9 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 35 mm, 25 , 103 U/min

Used extruder 35mm - 25 l/d with 5.6 kW drive 3-zone auger 3 heating/cooling zones on the cylinder + 1 tool zone Mass pressure sensor 500 bar All machine cables designed to be plugged in Control cabinet with main switch, motor controller, mass pressure indicator and 4 pieces of temperature controller Function-tested

Automatic Signature Punching Machine / Automatische Stanzmaschine JAMES BURN Lhermite EM 520 Baujahr / Year 1998 - Serial-No. 211661 Format Einlaufbreite / Size Infeed width 520mm Materialdicke / Thickness max. 3mm (32 pages 80 gr) Geschwindigkeit / Speed max. 10.000cycles/h Papierstärke / Paper thickness 70 to 300 gr.  James Burn Lhermite EM520 is an Automatic Signature Punching Machine.  It can be used for inline or offline production. With Feeder and Jogger delivery. The EM520 features the state of the art modular system for  punching and cutting signatures in line 

Stock # U2457-1 Used vibrating screen by Allgaier (D) model D1200. Contact parts stainless steel. Screen has working diameter 1200 mm. Single deck and cleaning deck with rubber balls. Feeding inlet has diameter 300 mm. Side wall outlet has connection 150 mm. Central discharge of final product has diameter 300 mm. Screen is driven by two vibrating motors, each: 1 kW, 980 rpm, 220/380 V, 50 Hz. Includes one screen mounted on machine and 5 additional stainless steel screens. Mounted on 4 lugs.

pressure: 40 t throat: 240 mm stroke: 8-88 mm no. of strokes: 57/86 Hub/min ram - range of adjustment: 63 mm table surface area: 560x450 mm ram surface: 240x200 mm hole in the table: Ø100 mm table height: 840 mm tool hole in ram: Ø40 mm weight of the machine ca.: 3,5 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t throat: 440 mm stroke: 19-230 mm no. of strokes: 58 Hub/min ram - range of adjustment: 100 mm table surface area: 1450x850 mm ram surface: 900x680 mm hole in the table: 300x300 mm table height: 950 mm tool hole in ram: Ø60 mm weight of the machine ca.: 19 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 1000 t stroke: 600 mm weight of the machine ca.: 4 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: . t throat: . mm stroke: . mm total power requirement: . kW weight of the machine ca.: 4 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A.Z.O. Indoor Silo System Round silo 4 x 4 tons in steel Control with Winback PC 100 kg scale for sale Price on request Phone 0172 8345457

2 x die-sinking EDM machines ZK Genius 700 BJ 1010 and 2019

Single column - eccentric press KRUPP type PEKRD 125 hMasch. No. 2861 Year of construction 1977Compressive force 125 ton. Projection 400 mmTable size 950 x 750 mmPlunger area 800 x 540 mmTable opening 100 x 250 mmStroke adjustment 8 to 160 mmPlunger adjustment 100 mmInstallation height largest stroke at the top max. 550 mmStroke rate 60 strokes/min. Table height above floor 800 mmEngine power 10 kWNetz connection 380 Volt, 50 Hz- Hydraulic overload in the plunger- Compressed air clutch-brake combination ORTLINGHAUS-

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Single column - eccentric press WEINGARTEN type ERV 40Masch. No. 537 / 65 Year of construction 1965Compressive force 40 ton. Projection 230 mmTable size 570 x 470 mmPlunger area 250 x 200 mmClamping pin hole 40 mmInstallation height max. approx. 520 mmStroke adjustment 8 - 88 mmPlunger adjustment range 63 mmStroke rate 70 strokes per minuteDrive power 3 kWNetz connection 380 volts, 50 Hz- Table height adjustment- Overload protection by crushing plate- Clutch-brake combination by WEINGARTEN friction threaded coupling-

Single column - eccentric press WEINGARTEN type ER 63Masch. No. 52A / 63 Year of construction 1963Pressure capacity 63 ton. Projection 280 mmTable surface 630 x 530 mmAdjustable plunger stroke 8-100 mmPlunger adjustment 63 mmStroke rate 65 strokes / min. Engine power 4 kWNetz connection 380 Volt, 50 Hz- Clutch-brake combination by WEINGARTEN friction threaded clutch- Electrical stroke release via foot switch- Wheel counters- Overload protection by crushing plate- Front crankshafts Support bearingSpace requirement L x W x H 1500

Single column - eccentric press PELS - RICHTER type PEKR 125Masch. No. 20684 Year of construction 1967Compressive force 125 ton. Projection 430 mmTable size 1100 x 750 mmPlunger area 890 x 650 mmTable opening 400 mmStroke adjustment 6 to 115 mmRam adjustment 100 mmInstallation height largest stroke top max. 450 mmClamping pin bore 50 mmStroke rate 60 strokes/min. Table height above floor 900 mmMotor power 7.5 kWNerg connection 380 volts, 50 Hz- overload protection by crushing plate in the plunger- compressed air

Single column hydraulic press SCHÖN type TES/CBbuilt in 1977Compressive force 63 ton. (160 bar)Projection 320 mmTable size 600 x 770 mmPlunger area 600 400 mmPlunger stroke 125 mmInstallation height max. 400 mm (with intermediate plate on the ram)Slide speed Rapid traverse downwards approx. 180 mm/sec. Ram speed work approx. 25 mm/sec. Pushrod speed upwards approx. 180 mm/sec. Table height above floor 870 mmDrive power 22 kWNet connection 380 volts, 50 HzTank capacity approx. 280 litres Hydraulic oil

Single column hydraulic press SCHULZ type SES 250Masch.Nr. 04.86.3511/3 Year of manufacture 1986Compressive force 25 ton. Retraction force 10 toProjection 360 mmTable surface 600 x 720 mmPlunger area 500 x 500 mmFailure opening in table 100 mmPin hole 40 mmPlunger stroke 400 mmInstallation height max. 600 mmTable height above floor 935 / 775 mmTank capacity hydraulics 380 litresDrive power 7.5 kWNet connection 380 volts, 50 Hz- Fixed stop adjustment in the press cylinder 180 mm- Light barrier

Single-column eccentric press MÜLLER GEFREES type PDET 5 S/EKMasch. No. Year of manufacture 1988Compressive force 5 ton. Projection 125 mmColumn passage 170 mm Table surface 280 x 220 mmWaste height 90mmLifting area 160 x 100 mmLifting adjustment 4 to 40 mmRam adjustment 30 mmInstallation height largest stroke at the top max. 210 mmStroke rate 200 strokes/min. Clamping pin bore 25 mmTable height above floor 900 mmEngine power 0.55 kWNerg connection 380 volts, 50 Hz- pneumatic clutch-brake combination-

Clamping Table, Sinusoidal Table, Swivel Clamping TableTable Length: 1130 mmTable Width: 300 mmTable Height: 112 mmFolding Angle: 2Folding Angle: max. 7- Folding Angle 2 via Threaded Spindle Folding Bracket max. 7 manually raised to the stopOverall Dimensions L x W x H: 1450 x 300 x 112 mmWeight: 275 kgGood ConditionClamping Plate, Ideal for Making Wedge Strips; used

Key data: 4 , 180 mm, 110 mm

SPECIFICATIONS: Length of the planer: 2300 mm Working width: 180 mm Working height: 110 mm Spindles: Ø 35 mm Number of spindles: 4 Chain drive (1.70 kW) Speed: 6000 rpm Installed power: 16.5 kW Voltage: 380 V SHAFT CONFIGURATION: I bottom (5.5 kW) II right (5.5 kW) III left (5.5 kW) IV top (5.5 kW) EQUIPMENT: 01 Unloader 01 Return Conveyor

Key data: 4 , 180 mm, 120 mm

SPECIFICATIONS: Length of the planer: 1700 mm Working width: 180 mm Planing height: 120 mm Spindles: Ø 35 mm Number of spindles: 4 Chain drive (1.70 kW) Speed: 6000 rpm Installed power: 16.5 kW Voltage: 380 V CONFIGURATION OF THE SPINDLES: I bottom (5.5 kW) II right (5.5 kW) III left (5.5 kW) IV top (5.5 kW)

• For applying security labels to both side flaps of a folding bo. • Output max. 100 cartons/min • Max. Folding box width in infeed direction crossways 180 mm, max. height 92 mm • Side conveyor belts • Upper retaining conveyor • 2 Label dispensers PAGOmat 6/2 A-100 with operating units • Label dispenser Height and crosswise adjustable • Label reels core diam. 76 mm, outer diam. max. 280 mm • Various controls via light barriers • Blow-out station for bad cartons with ejection countercheck • HMI Siemens Simatic Panel Touch, • PLC Siemens S7-300 CPU 314C-2DP • Mobile • Drive 400V/50Hz

CINCINNATI PROTON 45-30G Attention: Machine in left-hand version Screw diameter: 45 mm, L/D = 30 Grooved catchment zone Motor (DC drive): 65 kW Screw speed: max. 320 rpm Tool zones: 4+1 for adapters Melt pressure & temperature sensor included EXcPRO-NT control incl. CAN bus for data communication Air conditioner for control cabinet Cylinder in bimetal design – condition: very good Screw with few operating hours – condition: very good Without material funnel & without adapter

Weinig Profimat 22N four-sided planer Working width 220mm Working height 120mm Number of spindles: 4 Spindle arrangement Bottom 4wkw Rights Left 5.5kw Top 4kw Feed speed adjustable by variator 4-20m/min Total power 16kw

Z640 Mixed Lot (134 pieces) Feed Pliers Automatic Lathe Lathe Turning Center probably for Index Traub or Schütte or similar machines

Inv. Num. : 8601 Type: DV 40 W Producer: HAMM Generated: Parameters: Speed: 12 km/h Cylinder width: 1200 mm Length: 3310 mm Height: 2610 mm Width: 1425 mm Machine weight: 4100 kg

Weinig Profimat 22N ATS four-sided planer Working width 220mm Working height 120mm Number of spindles 5 Spindle system: Bottom 5.5kw Rights Left 7.5kw Top 5.5kw Bottom 4kw Feed speed adjustable via variator 6-22m/min Feed motor power 2.2kw Height and width set via controller Input table length 1970mm

Transnorm Belt Curve Conveyor left GKF 90°-780-600 IR600 both sides transmission RA2019 The Transnorm belt curve is in good condition (used) and fully functional. It has a gear motor of the brand SEW. Supports and are not included in the scope of delivery. They are optionally available on request. Belt curves are often used in intralogistics for the internal transport of unit loads and are indispensable in modern distribution centers. Transnorm belt curves convince with performance and reliability. Thanks to a low-tension drive over the entire belt width, long operating times are no problem. Conical drums and a specially developed belt guide system ensure the highest possible running smoothness. Technical data: Frame width (NB): 780 mm belt width (GuB): 600 mm height (BH): 210 mm Inner radius (IR): 600 mm Conveying angle: 90° degrees support feet: optionally available Conveying speed  ...

Transnorm right flush roller conveyor 3470-1830-1450 RA1855 Make: Transnorm Basic dimensions: conical structure, 3470x1160-1830 mm Length: 3470 mm Nominal/external width (NB): 1160-1830 mm Roll length (RB): 160-450 mm & 640-1000 mm Frame height: 290 mm Currently set height: 640 mm Height of side guide: 410 mm Width (height) side belt 300 mm Roller diameter: 50 mm Roller pitch: 65 mm Including 8 feet Motor MOVI-Mot 3x300-500V 1,5kW Conveying speed: Features: Construction year: 2017 Conveying length in mm (NL): 3470 Optional erhältlich: Frequenzumrichter Electric data: 70Hz, 217 / 375 V Antrieb: Nord-Drivesystem Supports: 8 Bauhöhe in mm (BH): 290 Belt width in mm (GuB): 300 Height in mm: 640 Galvanized rollers: Ø = 50 mm scope of delivery: including supports and side guides, Kabel, ohne Frequenzumrichter Roll width in mm: 160-450, 640-1000 condition: Ausstellungsstück Roll division i ...

Manufacturer: MINOX Type: MTS 2000/1 Built in 1999 Surface: 2.5 m² Dimensions diameter: 180 cm Weight: 1200kg Space requirement: 240 cm x 240 cm Available quantity: 2 pcs. Condition: used, fully functional

35.000 litre, Stock number: T485, Litre: 35.000, Material: Fiberglass, In stock: Yes, Amount in stock: 1 pc., Item: Silo, Standing: On legs, Top: Dished, Bottom: Conical, Tank cover: In the top, Ø 600 mm., Working temperature: 30° C, Inner diameter: Ø 3300 mm. , Other: Max density 0,7, Year: 1989

We are selling our die-sinking EDM system here because of a new acquisition. This is a machine that was sold by the company MATRA at that time. This is a DECKEL DE35C. In the meantime, the company Exeron has taken over the service. The travel is: X=600mm Y=400mm Z=400mm The die-sinking EDM system has a 4-fold electrode changer The control system on the machine was recently overhauled, the power supply and the UPS were renewed. The machine was also otherwise continuously checked and maintained by the Exeron company in the event of malfunctions. Machine is running and is still on the power for a possible test. Operating hours are: 33196 hours. Various tool holders can be part of the price negotiation.

Key data: 4 , 240 mm, 130 mm

SPECIFICATIONS: Feed length: 2500 mm Machining width: 240 mm Processing height: 130 mm Spindles: Ø 40 mm Number of Spindles: 4 Shaft drive (2.9 kW) Installed power: 24 kW Voltage: 380 V CONFIGURATION OF THE SPINDLES: I bottom (5.5 kW) II right (7.5 kW) III left with electronic sideshift (7.5 kW) IV top (7.5 kW) EQUIPMENT: Complete with tools