internal grinding si used for sale

Stainless steel vibrating sieve for wet sieving, 1 deck with 915 mm, 2 outlets, with unbalance drive (approx. 1 kW) and springs. 2 pcs. available.

Tank Environmental Protection Wozniack . Specialist establishment according to Section 19 of the Water Budget Act (WHG) offers as follows . Diesel tank 16,000 liters double-walled used, with a used diesel pump DK 70 EZ: The pump is 1 year young and was overhauled by the manufacturer general. The container is used, cleaned, overhauled and is equipped with the following fittings: 1 optical leak detector with type approval and leakage liquid (new) 1 filling pipe with TW closure (filling cap) and immerse tube, 1 bearing tube with bearing rod and bearing rod closure, 1 vent pipe with vent hood, 1 brand new limit sensor with type approval (AIII) (new) 1 ladder 1 diesel pump DK 70 EZ Container dimensions Length 8,290 mm Diameter 1,600 mm Weight approx. 3,000 kg Of course, you can also use your tank system. We are happy to offer you diesel pumps with a hig ...

MATEC easily from our own development and production running lightly and quietly and transport bulk material and individual loads up to 250 kg with minimal energy over long distances up to 12 m at a time with a hand drill 300 w power consumption. The combined forced - and promotion of resonance stores the kinetic energy in the spring and must compensate for only the frictional resistance of the material. Sawdust, shavings, gravel, Earth, grain, hay and grass, etc. are exactly same speed transported with approximately 17 m / min. by means of Frequenzumforner the speed can be adjusted. The transport and screening in a single operation with a built-in sieve base perforation on request MATEC Vibrorinne standard Trough width inner 500 mm Trough height inner 260 mm current trough length 2500 mm (can front and rear to 1.5 m be extended without additional support) In addition current ...

Silo used approx. 75 m ³ / 75,000 litres polyester silo / GRP silo standing, with or without frame, good condition Dimensions: approx. Ø 3,0 m x 12 m high without frame Bulk density 1, 2 t / m ³, Speidel tank, The container can be used as storage tank for water, liquid food, whey, potato steam skins, molasses, grain, salt, rain collection tank, and so on. Price upon request. Transport can be arranged at low cost. Also we can modify the tank to suit your demands, just ask us. It is not possible to update all our advertisements daily. Since our inventory is changing continuously, it may be that this tank has already been sold but a similar one is in stock. Please give us a call or write, so that we can advise you personally. More information and offers on our site: profi-tanks(dot)de

1 factory-tested, well-preserved single-girder ceiling crane Load approx. 3,200 kg Wingspan approx. 6.280 mm Hook path about 12,000 mm Make DEMAG Year of production/workshop testing 1991/2016 with DEMAG monorail trolley, freely movable floor control Working speeds: Hoist approx. 1.3/8.0 m / min Trolley gear approx. 5.0/20,0 m / min Crane chassis approx. 10.0/40.0 m / min

1 neuwertiger, factory-tested single overhead travelling crane with angle trolley Oblique cord stabilization for traverse operation Payload 10.000 kg Span approximately 15,850 mm make VOITH Year of production/workshop test 1995/2016 Lasting only 1 year equipped in a space-saving design with angle trolley and inclined stranding to the load-stabilisation (magnetic control prepared, but not included in the delivery), trolley with frequency control operating speeds, cradle frame, radio remote control: Hoist load approx. 0 8.3 m / min Load approx. 0 22.0 m / min Trolley gear 0-40.0 m / min Crane chassis 0-60.0/90.0 m / min

Basic-outdated Fortuna Gr.4 machine was anew varnished completely dismantled and wearing parts were renewed. 6-month guarantee taking back old machine possibly.

Kragarmregal, double-sided, 5.18m height, 1.20m arms, 870kg per arm - NEW - : Price from location incl. loading! 1 shelving unit with 4 pcs 2,495.-EUR (net)! A Kragarm shelving system, hot-dip galvanized, consisting of: 4 double-sided shelves approx. 5.18 m high, hot-dip galvanized IPE 180 / 100 with 2x3 each. Arms 1.20 m, 870 kg load capacity per arm with verbatim approx. 1.30 m shelf divider approx. 5180mm high, hot-dip galvanized foot and arm depth 1200 mm with 3 adjustable shelf arms each with centre of gravity 600 mm 870 kg per arm / 2610 kg per stalker with laengs and diagonal connectors e = 1300 mm for a shelf row with 4 stems approx. 4000 mm long with all screws and nuts, without bottom anchors . Other configurations (frame height, armrails, arm types, etc.) can be used! Please contact us! photos of an old shelf!; New

4 CUTTER HEADS, MAX. DIMENSIONS OF THE WORK PIECE: 180/120 MM, MIN. DIMENSINS OF FINISHED WORK PIECE: 16/7 MM, SPINDLE SPEED: 6000 RPM, OPERATION HOURS: 30 HOURS ONLY!

Kragarmregal, double-sided, 5.18m height, 1.20m arms, 500kg per arm - NEW - : Price from location incl. loading! 1 shelving unit with 4 pcs 2,295.-EUR (net)! A Kragarm shelving system, hot-dip galvanized, consisting of: 4 double-sided shelves approx. 5.18 m high, hot-dip galvanized IPE 180 / 80 with 2x3 each. Arms 1.20 m, 500 kg load capacity per arm with verbatim approx. 1.30 m shelf divider approx. 5180mm high, hot-dip galvanized foot and arm depth 1200 mm with 3 hoes-adjustable shelf armseached carrying capacity at load centre 600 mm 500 kg per arm / 2610 kg per staender with laengs and diagonal connectors e = 1300 mm for a shelf row with 4 stems approx. 4000 mm long with all screws and nuts, without bottom anchor s. Other configurations (frame height, armrails, arm types, etc.) can be used! Please contact us! photos of an old shelf!; New

We offer a general overhault exchange engine with 12-month guarantee with starter+altenator . We are an Agco Sisu diesel service partner and obstruct / sell only original spare parts. Please contact us: MIW GmbH Motoren Instandsetzungs Werk Nord West Ring 8 D-27404 Zeven-Germany Tel:0049 (0) 4281-950583 Fax:0049 (0) 4281-950585 e-mail: info@miw-zeven.de abc. miw-zeven.de

Kragarmregal, double-sided, 4,16m height, 1.20m arms, 500kg per arm - NEW - : Price from location incl. loading! 1 shelf unit with 4 pcs 1.850.-EUR (net)! A Kragarm shelving system, hot-dip galvanized, consisting of: 4 shelves double-sided approx. 4.16m high, hot-dip galvanized IPE 160 / 80 with 2x3 each. Arms 1.20 m, 500kg load capacity per arm with verbatim approx. 1.30 m shelf divider approx. 4160mm high, hot-dip galvanized foot and arm depth 1200 mm with 3 hoes-adjustable shelf arms carrying ability at load centre 600 mm 500 kg per arm / 2250kg per stem with laengs and diagonal connectors e = 1300 mm for a shelf row with 4 stems approx. 4000 mm long with all screws and nuts, without bottom anchors. Other configurations (frame height, armrails, arm types, etc.) can be used! Please contact us! photos of an old shelf!; New

intake cross section: 2500 x 1,700 mm motor power: 160 kW rotor flight circle: 670 mm rotor execution: cutting inserts on tool holders counterknife: with cut gap adjustment machine weight: approx. 24,000 kg

Kragarmregal, double-sided, 3,50m height, 1,20m arms, 500kg per arm - NEW - : Price from location incl. loading! 1 shelving unit with 4 staenders 1.750.-EUR (net)! A Kragarm shelving system, hot-dip galvanized, consisting of: 4 double-sided shelves approx. 3.50m high, hot-dip galvanized IPE 160 / 80 with 2x3 each. Arms 1.20 m, 500kg load capacity per arm with verbatim approx. 1.30 m shelf divider approx. 3500mm high, hot-dip galvanized foot and arm depth 1200 mm with 3 hoes-adjustable shelf arms carrying ability at load centre 600 mm 500 kg per arm / 2250kg per staender with laengs and diagonal connectors e = 1300 mm for a shelf row with 4 stems approx. 4000 mm long with all screws and nuts, without bottom anchor s. Other configurations (frame height, armrails, arm types, etc.) can be used! Please contact us! photos of an old shelf!; New

Kragarmregal, double-sided, 3,50m height, 1,20m arms, 750kg per arm - NEW - : Price from location incl. loading! 1 shelf unit with 4 pcs 1.900.-EUR (net)! A Kragarm shelving system, hot-dip galvanized, consisting of: 4 shelves double-sided approx. 3.50m high, hot-dip galvanized IPE 160 / 100 with 2x3 each. Arms 1.20 m, 750kg load capacity per arm with verbatim approx. 1.30 m shelf divider approx. 3500mm high, hot-dip galvanized foot and arm depth 1200 mm with 3-adjustable helving armseached each carrying ability at load centre of gravity 600 mm 750 kg per arm / 2250kg per staender with laengs and diagonal connectors e = 1300 mm for a shelf row with 4 stems approx. 4000 mm long with all screws and nuts, without bottom anchors Other configurations (frame height, armrails, arm types, etc.) can be used! Please contact us!; New

Horizontal side channel pump Materials: - Case: 1.4581 - Wheels: 1.4408 - Wave: 1.4571 Housing sealing: single-acting sliding ring seal, carbon/silicon carbide/viton Version A6: Pump mounted on base plate elastically coupled with 1.35 kW IEC standard rotary current motor Pressure: 2 bar Power: 800 l/h Revolutions: approx. 1,450 rpm Rated frequency: 50 Hz Engine power: 230/400 V Protection class: IP 55 Type of protection: E Ex eII T3 Type of construction: B3 Pumps partly unused, therefore in very good condition!

Table 486 x 280 mm, X/Y/Z = 300/200/300 mm

Accessories

Length: 350 mm Width: 150 mm Polarity ~ 9 mm Space requirement approx.: L: 440 x W: 210 x H: 135 mm Voltage: 24V Power: 2,04A

Collar shelving, double-sided, 5, 18 m high, 1, 20 m arms, 870 kg per arm - new -: Price from site including loading! 1 shelf unit with 4 stand EUR2.495.-(net)! A cantilever rack system, hot-dip galvanized, consisting of: 4 shelf stand double-sided measures 5.18 m, hot-dip galvanized IPE 180 / 100 with each 2 x 3 verstellb. Poor 1.20 m, 870 kg capacity per arm with associations about 1.30 m Shelf stand double-sided about 5180 mm high, hot-dip galvanized Foot and arm depth 1200 mm with 3 adjustable shelf arms Load capacity at load Centre 600 mm 870 kg each arm / 2610 kg per stand with longitudinal and diagonal associations e = 1300 mm When a shelf set with 4 stands approx. 4000 mm long with all bolts and nuts, without ground anchor. Other configurations (frame height, arm length, arm types etc.) can be selected. Please speak to us! Photos of a similar rack!

For Amos press 1600 3 Steück new mesh belts type 5060 22600 Mm Width 1600 mm Chain and closure polyester unit price 2250,-

Collar shelving, double-sided, 5, 18 m high, 1, 20 m arms, 500 kg per arm - new -: Price from site including loading! 1 shelf unit with 4 stand EUR2.295.-(net)! A cantilever rack system, hot-dip galvanized, consisting of: 4 shelf stand double-sided measures 5.18 m, hot-dip galvanized IPE 180 / 80 with each 2 x 3 verstellb. Poor 1.20 m, 500 kg load capacity per arm with associations about 1.30 m Shelf stand double-sided about 5180 mm high, hot-dip galvanized Foot and arm depth 1200 mm with 3 adjustable shelf arms Load capacity at load Centre 600 mm 500 kg each arm / 2610 kg per stand with longitudinal and diagonal associations e = 1300 mm When a shelf set with 4 stands approx. 4000 mm long with all bolts and nuts, without ground anchor. Other configurations (frame height, arm length, arm types etc.) can be selected. Please speak to us! Photos of a similar rack!

Collar shelving, double-sided, 4, 16 m high, 1, 20 m arms, 500 kg per arm - new -: Price from site including loading! 1 shelf unit with 4 stand EUR1.850.-(net)! A cantilever rack system, hot-dip galvanized, consisting of: 4 shelf stand double-sided about 4, 16 m high, hot-dip galvanized IPE 160 / 80 with each 2 x 3 verstellb. Poor 1.20 m, 500kg load capacity per arm with associations about 1.30 m Shelf stand double-sided about 4160 mm high, hot-dip galvanized Foot and arm depth 1200 mm with 3 adjustable shelf arms Load capacity at load Centre 600 mm 500 kg each arm / 2250 kg per stand with longitudinal and diagonal associations e = 1300 mm When a shelf set with 4 stands approx. 4000 mm long with all bolts and nuts, without ground anchor. Other configurations (frame height, arm length, arm types etc.) can be selected. Please speak to us! Photos of a similar rack!

Collar shelving, double-sided, 3, 50 m height, 1, 20 m arms, 500 kg per arm - new -: Price from site including loading! 1 shelf unit with 4 stand EUR1.750.-(net)! A cantilever rack system, hot-dip galvanized, consisting of: 4 shelf stand double-sided 3, 50 m high, hot-dip galvanized IPE 160 / 80 with each 2 x 3 verstellb. Poor 1.20 m, 500kg load capacity per arm with associations about 1.30 m Shelf stand double-sided approx. 3500 mm high, hot-dip galvanized Foot and arm depth 1200 mm with 3 adjustable shelf arms Load capacity at load Centre 600 mm 500 kg each arm / 2250 kg per stand with longitudinal and diagonal associations e = 1300 mm When a shelf set with 4 stands approx. 4000 mm long with all bolts and nuts, without ground anchor. Other configurations (frame height, arm length, arm types etc.) can be selected. Please speak to us! Photos of a similar rack!

tower silos 4 x 50 m³ / 50000 litres of polyester tanks / Tower silos / flour silos, GRP silos, grain silo / hopper silo / compound feed component silo Top condition Content per silo: 50 m³ / 50000 litres piece / pc: 4 pieces Year of construction: 1994 mass of Tower silos without steel: approx. Ø 2,80 x 12 m high Height of the entire system: 21 m Density/weight: 1,200 kg per m³ approval number: Z 10-22-42 Manufacturer: Polem More details: the silos are in good used condition. According to the age traces are present. The system has complete works until its closure. The system could not be tested yet, because there is no power supply. It is a complete meal silo plant with very thick-walled 4 x 50 m³ GRP silos with a density/weight 1200 kg per m³ is each silo separately to fill up the tanks through several cross conveyor (scraper conveyors). The silo is a spray head to cle ...

Collar shelving, double-sided, 3, 50 m height, low-1, 20 m, 750 kg per arm - new -: Price from site including loading! 1 shelf unit with 4 stand EUR1.900.-(net)! A cantilever rack system, hot-dip galvanized, consisting of: 4 shelf stand double-sided 3, 50 m high, hot-dip galvanized IPE 160 / 100 with each 2 x 3 verstellb. Poor 1.20 m, 750kg load capacity per arm with associations about 1.30 m Shelf stand double-sided approx. 3500 mm high, hot-dip galvanized Foot and arm depth 1200 mm with 3 adjustable shelf arms Load capacity at load Centre 600 mm 750 kg each arm / 2250 kg per stand with longitudinal and diagonal associations e = 1300 mm When a shelf set with 4 stands approx. 4000 mm long with all bolts and nuts, without ground anchor. Other configurations (frame height, arm length, arm types etc.) can be selected. Please speak to us!

Material: mild steel Year of construction: 2003 Drive: 5.5 KW Weight: 2150 kg Area per deck: 5.3 m2 Machine fully reconditioned with new bearings. Optional: ball knocking cleaning, basket of your choice: 0.1-20 mm.

Dynamic airflow separator (sifter) for minerals, cement, recycling etc., rotor diameter: 700 mm, turbine wheel occupied with 64 blades / turbine blades, outer ring occupied with 36 manually adjustable counter wings, incl. drive. In very good condition.

To sieve dry material: like flour-, grainy-, and granule-shaped material. Free running sieve case hanging in a massive framework With an automatic sieve ball cleaning. Sieve-layers in a simple way interchangeably. Applicable to sieve all floury-, grainy materials in dry condition. Sizes of Wide 500 – 1500mm / Lengths 1200 – 2400mm Sieve layers 2 to 4 layers, grain

Iddon Cold Feed Extruder. 2.5" screw dia. 10/1 LD Ratio. Motor Size 20.4/5.5 HP

Materials: Housing: 1.4581 Wheels: 1.4408 wave: 1.4571 Sealing: single-acting mechanical seal, carbon/silicon carbide/Viton Model A6: Pump on base plate mounted elastic coupled with 1.35 kW IEC standard motor, three-phase Pressure: 2 bar Revolutions: approx. 1,450 U/min Output: 1,200 l / h Mains frequency: 50 Hz Engine power: 230/400 V Protection class: IP 55 protection class: E ex eII T3 Design: B3 Pump partially unused in excellent condition!

Used single stage homogeniser made by Hoyer Pack. Capacity 600 L/H. Bal type valve. 6.5 KW motor. Set of seales and plungers ware changed lately. New 1996.

Technical data: Nominal power 600 kg/h Power: Drive engine 0.75 (1.02) kW (hp) Brush cleaning 0.37 (0.5) kW (hp) High-pressure cleaner 4.7 (6.4) kW (hp) Electric connection 400V 50Hz (3 phases) Electrical protection 16 A Dimensions: Length 1 825 mm Width 1 085 mm Height 1 290 mm Discard or drop-in height 1 290 mm Bandwidth 420 mm Order width 300 mm Order height 10-50 mm Weight (ribbon press) 550 kg Material 1,4301/AISI 304 Juice yield 70% Ribbon speed (infinite) 2.1-5.5 m/min Transcourse time 0.4-1 min Water connection at least G 1/2, "min 12 l/min Height juice drain 305 mm Height Trester ejection 780 mm Can be used for nuclear and stone fruits Included high pressure cleaner, compressor

Sieve Drum Waste Waste Product Drum Sieve Machine Screening System 2.24 m Diameter 7.5 Kw Stainless Steel Enclosure used Manufacturer: Lohse Total length: approx. 6337 mm Drum diameter: 2240 mm Height: approx. 4807 mm Plant width: approx. 3400 mm Sorting screen plate 1st zone: 8x60 mm Sorting screen plate 2nd zone: 6x40 mm Operating weight (filled): approx. 11000 kg Empty weight complete: approx. 9500 kg Drum housing is made of stainless steel, screen basket iron Motor data - drum drive Three-phase motor type R93DV 132M4 Power: 7.5 kW Engine speed: 1430 rpm Drive speed: 25 rpm Speed drum: 10 rpm Connection: 230/400 V Rated current: 16 A Frequency: 50 Hz Protection: IP54 Design: B3 The sieve drum has already been dismantled and cleaned. Item location 01587 Riesa, visit possible.

1 factory-tested ceiling crane girder Lifting capacity 3000 kg Wingspan approx. 6,800 mm Hook way approx. 8,000 mm Make MAN GHH Year of production/workshop testing 1988/2016 equipped monorail trolleys, short type, freely movable floor control Working speeds: Hoist around 0.8/8.0 m / min Trolley gear approx. 4.0/16.0 m / min Crane chassis approx. 8.0/32.0 m / min

1 factory-tested, very well-preserved single-girder crane Lifting capacity 3,200 kg Span approximately 6,000 mm hook path Max 12,000 mm Make DEMAG Year of production/workshop test 1993/2016 with DEMAG monorail trolley, freely movable floor control Working speeds: Hoist CA. 1.0/6.3 m / min trolley gear approx. 14.0 m / min crane chassis 10.0/40.0 m / min

1 factory-tested, very well-preserved single-girder crane with angle trolley load approx. 4,000 kg Load trolley CA 5,000 kg Wingspan approx. 7.100 mm Make steel Year of production / workshop testing 1986/2016 Crane radio control equipped with angle trolley for a perfect hook road, Working speeds: Hoist 0.5/3.25 m / min Trolley gear approx. 5.0/20,0 m / min Crane chassis approx. 10.0/40.0 m / min

1 factory-tested single girder overhead travelling crane lifting capacity 5000 kg Span around 10,000 mm Hook way max. 5.000 mm Make steel Year of production/workshop test 1983/2016 Crane equipped with steel monorail trolley, freely movable floor control Working speeds: Hoist 0.5/3.4 m / min Trolley gear 16.0 m / min Crane chassis 4.0/16.0 m / min

1 factory-tested, very well preserved single girder crane angle load approx. 5,000 kg Wingspan approx. 10,000 mm Hook path about 7,500 mm Make steel Workshop examination 2016 Floor control equipped with angle trolley for optimal hook path, freely movable working speeds: Hoist approx. 0.8/5.0 m / min Trolley gear approx. 5.0/20,0 m / min Crane chassis approx. 4.0/16.0 m / min

1 factory-tested, well preserved double girder crane Load capacity 5000 kg Span width 14.780 mm Hook path maximum approx. 8,000 mm Make RÖTTGER/Demag Workshop examination 2016 Floor control freely movable with DEMAG double girder trolley, Working speeds: Hoist approx. 0.8/8.0 m / min Katz LG 5.0/20,0 m / min Crane chassis 10.0/40.0 m / min

1 plant be certified, very well received. Single girder overhead travelling crane with angle trolley Load approx. 5,000 kg Wingspan approx. 16.750 mm hook path maximum approx. 8,000 mm Make VOITH Year of production/workshop test 1993/2016 equipped in a space-saving design with angle trolley and inclined stranding to the load-stabilisation including load beam, with frequency control, maintenance Jetty, radio control Working speeds: Hoist up to 20.0 m / min Trolley gear up to approx. 26.0 m / min Crane chassis up to approx. 90.0 m / min

1 factory-tested single angle crane in design with laterally movable carrier trolley Load approx. 5,000 kg Span approximately 33,000 mm Hook way max. 9000 mm Make AUMUND/steel Year of production/workshop test 1981/2016 with steel angle trolley for maximum hook path, DEMAG Kranfahran- drove, corridor control freely movable Working speeds: Hoist approx. 1.3/8.0 m / min Trolley gear 10.0/40.0 m / min Crane chassis up to 60.0 m / min

1 factory-tested, well-preserved single-girder crane Load approx. 6,300 kg Wingspan approx. 14,200 mm Hook path about 8.000 mm Fabrikat DEMAG Year of production/workshop test 1974/2016 Crane equipped with DEMAG monorail trolley, freely movable floor control Working speeds: Hoist 1.0/10.0 m / min Katz LG 5.0/20,0 m / min Crane chassis 10.0/40.0 m / min

Sieve drum machine Trützschler SF144 used for the processing of cotton fibres and similar fabrics. Manufacturer: Trützschler Type: SF144 with hose filters, each 15 hooks of 200 mm left and right In the middle of the machine is the sieve drum (length 1,200 mm approx. 500 mm), with fine stainless steel sieve fabric, clamped on square screen basket. Machine was used for separating/filtering cotton fibers and other light fabrics. with fan Dimensions filter box: 850 x 1,500 H 1,100 over frame, H with frame 2,300 mm Total space requirement: 2,300 x 2,000 H 2,800 mm 2 identically available. Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.

1 factory-tested, well-preserved single-girder crane Load approx. 6,300 kg Wingspan approx. 19.134 mm Hook path about 8.000 mm Fabrikat ABUS/DEMAG Year of production/workshop test 1974/2016 Crane equipped with DEMAG monorail trolley, freely movable floor control Working speeds: Hoist 1.0/10.0 m / min Katz LG 5.0/20,0 m / min Crane chassis 10.0/40.0 m / min

2 factory-tested, well preserved single girder cranes Payload 7000 kg Wingspan approx. 16.650 mm Hook way approx. 4,000 mm Fabrikat DEMAG/MAN-SWF Workshop tests 1987/1991/2016 Cranes equipped with DEMAG and SWF monorail trolleys with short design, freely movable floor control Working speeds: Hoist CA. 0.3/3,1 m / min Katz LG 5.0/20,0 m / min Crane chassis 10.0/40.0 m / min

2 factory-tested, well-preserved single girder suspension cranes Payload 10.000 kg Gauge approximately 17,700 mm Lifting height Max approx. 9,300 mm Make MAN / SWF Year of construction/workshop test 1987 1990/2016 Service life approx. 3 years with SWF monorail trolleys short type, long travel rate programs, freely movable floor control Working speeds: Hoist CA. 0,8/8 m / min Trolley gear approx. 20 m / min Crane chassis approx. 40 m / min

1 factory-tested, absolutely like new single angle crane Payload 10.000 kg Wingspan approx. 26.610 mm Hook path about 10,000 mm Make DEMAG Year of production/workshop test 2001/2016 Crane equipped with electric wire rope hoist moving on the side of the vehicle, cross and long travel frequency controlled remote control, Working speeds: Hoist CA. 0.6/4.0 m / min Trolley gear (FU) approx. 0-30,0 m / min Crane chassis (FU) approx. 0-40.0 m / min

1 factory-tested, very well-preserved single-girder crane Load trolley CA 10,000 kg Lifting capacity crane approx. 20,000 kg Wingspan approx. 39,500 mm hook path approximately 15,000 m Make helper / ABUS Year of production / workshop testing 2012/2016 Crane equipped with floor control as emergency steering, ABUS monorail trolley, radio control Working speeds: Hoist approx. 0.8/5.0 m / min Trolley gear infinitely variable approx. 1.0 20.0 m / min Crane chassis approx. 10.0/40.0 m / min