injection used for sale

Key data: 350 , 53 , 28

BOY 35 E injection molding machine Type : 350-92 35E?Year: 2014?Screw diameter : 28 mm?Injection pressure: 1639 bars?Injectable volume : 58,5 cm³ Weight in PS : 53,2 gr?Clamping Force: 35 T?Distance between tie bar bar: 280 x 254 mm?Mould installation height min : 200 mm?Plate distance max : 500 mm?Dimensions: 2400 x 820 x 1950 mm?Weight: 1195 kg

Diesel engine, propulsion engine, marine diesel, injection pump, fuel pump, fuel injection pump -Manufacturer: Bosch, injection pump for 6-cylinder diesel engine -Type: PES6R120/720LV B 403 860 177 RQV300-900 RV -Individual components: see photos -Number: 2x injection pumps available -Price: per piece -Dimensions: 460/215/H325 mm -Weight: 32 kg

diesel engine, propulsion engine, marine diesel, injection pump, fuel pump, fuel injection pump, diesel generator, diesel generator -Manufacturer: Bosch, injection pump from generator MWM RHS 518V16 -Injection pump: Bosch EP/RSUV300-750P9/332/1R PE8P120/520RS190 -Feed pump: Bosch FP/K 22 P11 -Shaft: Ø20 - 25mm / M18x1.5 -Individual components: see photos -Dimensions: 1000/170/H290 mm -Weight: 41 kg

Injection molding cutting device for injection molding machine, injection molding machine, cutting pliers -Cutting device: for cutting plastic sprues, tabs, overflow cavities, webs, etc. -6 Cutting pliers: Cutting insert/individual components see photos -Price: complete -Total dimensions 1570/770/H680 mm -Weight: 49 kg

Key data: 6 kN, 2582 g/PS, 90 mm

Tederic NEO H680-i4800 – Two-platen injection molding machine Exhibition piece with minimal operating hours – excellently equipped! This machine is a former pilot plant and demonstration device that was used exclusively for demonstration and test purposes. Accordingly, the The machine has hardly any operating hours and is in excellent condition. The extensive equipment goes far beyond the standard. --- Technical data - Clamping force: 680 t (6,669 kN) - Year of construction: 2022 - Injection unit: i4800 - Screw diameter: 90 mm - Injection weight (hp): 2,582 g - Injection volume: 2,837 cc - Spec. Spray pressure: 1,615 bar - L/D Ratio: 20.8 - Clamping plates: 1,500 x 1,400 mm - Handlebar spacing: 1,100 x 960 mm - Ejector force: 182 kN - Tool installation height: 450 mm - Opening travel: 1,400 mm - Max. panel spacing: 1,850 mm - Ejector trave ...

Key data: 589 kN, 25 mm

Clamping force: 60t Year of Make: 2001 Injection Unit .../100 Screw diameter: 25 mm Spec. Spray pressure: 2240 bar Spray volume: 49 cc Clamping unit 600/... Clamping force: 60 t Size of the clamping plates: 446 x 446 mm Clearance spar spacing: 320 x 320 mm Tool installation height: 200 mm Opening travel: 350 mm Max. plate spacing: 550 mm Weight: 2440 kg Dimensions(m) LxWxH: 3.6 x 1.6 x 2.2 m Year of Make: 2001 Control type Selogica

Key data: 4200 kN, 1090 g/PS, 70 mm

Demag Ergotech 420/800 2300 with embossing function and Robot Wittmann DR 633/CNC 6-316 Prices are at: inventar-verkauf.de/id/alesco Details: Clamping force: 4200 KN Handlebar width: 800 x 710 mm Mold opening: 710 mm Control Ergocontrol NC 4 Connected load: 68KW Total dimensions: 7.9 x 2.2 x 2.5 m Total weight: 21.0 t Accessories/Equipment: Robot Wittmann DR 633/CNC 6 - 316 (XxYxZ) 900 x 1600 x 3000 servo with support and enclosure 2-fold core pull 2 I/O Embossing function retrofitted 2 x Injection Unit: Injection Unit 1 Weft volume: 891 cm Weft weight: 800gr (polystyrene) Screw diameter 60mm Injection pressure 2420 bar Injection Unit 2 Weft volume: 1212 cm Weft weight: 1090gr (polystyrene) Screw diameter 70 mm Injection pressure 1877 bar WITHOUT COOKING VACUUM CLEANER and CLAMPING DEVICE.

Key data: 600 kN, 25 mm

Clamping force: 60t Year of Make: 2001 Injection Unit .../100 Screw diameter 25 mm Spec. Spray pressure 2240 bar Injection volume 49 cc Clamping unit 600/... Clamping force 60 t Size of the clamping plates 446 x 446 mm Lights spar spacing 320 x 320 mm Tool installation height 200 mm Opening way 350 mm Max. panel spacing 550 mm Weight 2440 kg Dimensions(m) LxWxH 3.6 x 1.6 x 2.2 m Year of construction 2001 Control type Selogica

Key data: 600 kN, 94 g/PS, 30 mm

Clamping force: 60t Year of Make: 2001 Injection weight in hp: 94g Injection Unit .../200 Screw diameter 30 mm Spec. Spray pressure 1995 bar Injection volume 106 cc Injection weight in hp 94 g L/D Screw Ratio 20 Clamping unit 600/... Clamping force 60 t Size of the clamping plates 600 x 600 mm Lights spar spacing 420 x 420 mm Tool installation height 200 mm Opening way 550 mm Max. panel spacing 750 mm Weight 3950 kg Dimensions(m) LxWxH 4.2 x 1.4 x 2.0 m Year of construction 2001 Control type NC4

Key data: 600 kN, 94 g/PS, 30 mm

Clamping force: 60t Year of Make: 2001 Injection weight in hp: 94g Injection Unit .../200 Screw diameter 30 mm Spec. Spray pressure 1995 bar Injection volume 106 cc Injection weight in hp 94 g L/D Screw Ratio 20 Clamping unit 600/... Clamping force 60 t Size of the clamping plates 600 x 600 mm Lights spar spacing 420 x 420 mm Tool installation height 200 mm Opening way 550 mm Max. panel spacing 750 mm Weight 3950 kg Dimensions(m) LxWxH 4.2 x 1.4 x 2.0 m Year of construction 2001 Control type NC4

Key data: 1750 kN, 393 g/PS, 50 mm

Clamping force: 175t Year of Make: 2005 Injection weight in hp: 393g Injection Unit .../1000 Screw diameter 50 mm Spec. Spray pressure 2304 bar Injection volume 432 cc Injection weight in hp 393 g L/D Screw Ratio 22 Clamping unit 175/... Clamping force 175 t Size of the clamping plates 915 x 910 mm Lights spar spacing 560 x 560 mm Tool installation height 350 mm Opening way 700 mm Max. panel spacing 1050 mm Ejector path 200 mm Weight 9000 kg Dimensions(m) LxWxH 5.2 x 1.75 x 2.2 m Year of construction 2005 Control type MC4

Key data: 2000 kN, 55 mm

Clamping force: 200t Year of Make: 2002 Injection Unit .../675 Screw diameter 55 mm Spec. Spray pressure 2080 bar Injection volume 427 cc Clamping unit 2000/... Clamping force 200 t Size of the clamping plates 950 x 950 mm Lights spar spacing 570 x 570 mm Tool installation height 300 mm Opening way 650 mm Max. panel spacing 950 mm Year of construction 2002 Control type Selogica

Key data: 2400 kN, 594 g/PS, 55 mm

Injection Unit .../1330 Screw diameter 55 mm Spec. Spray pressure 2041 bar Injection volume 653 cc Injection weight in hp 594 g L/D Screw Ratio 22 Clamping unit 240/... Clamping force 240 t Size of the clamping plates 910 x 930 mm Lights spar spacing 630 x 570 mm Ejector force 59 kN Tool installation height 350 mm Opening way 725 mm Max. panel spacing 1075 mm Ejector path 200 mm Weight 10000 kg Dimensions(m) LxWxH 5.5 x 1.8 x 2.4 m Year of construction 2013 Control type Unilog B6

Distance between the bars 710x630 mm, hole centering ring fixed plate Diameter 160 mm, minimum installation height 250 mm, maximum open travel 1450 mm, core pull 2, documentation, Machine was dismantled in 2014, overhauled (Italy) and recommissioned, equipped with hydraulic screw drive, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-10

Distance between the bars 710x630 mm, hole centering ring fixed plate Diameter 160 mm, minimum installation height 250 mm, maximum open travel 1450 mm, core pull 2, documentation, Machine was dismantled in 2014, overhauled (Italy) and recommissioned, equipped with hydraulic screw drive, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-12

Distance between the clamps 630x560 mm, hole centering ring fixed plate Diameter 125 mm, minimum installation height 200 mm, maximum open travel 1500 mm, 180 Kw, core pull 1, equipped with hydraulic screw drive, documentation, Please note! pick up by appointment, Auction-ID: A1-43992-9

Key data: 6500 kN, 80 mm

Clamping force: 650t Year of construction: 2024 Injection Unit .../4630 Screw diameter 80 mm Spec. Spray pressure 2090 bar Injection volume 2212 cc Hydr. Drive power 113 kW L/D Screw Ratio 22 Clamping Unit 6500/... Clamping force 650 t Lights spar spacing 1040 x 910 mm Ejector force 110 kN Tool installation height 400 mm Opening way 950 mm Max. panel spacing 1350 mm Ejector path 250 mm Weight 27000 kg Year of construction 2024 Control type KEBA 2985 Clamping unit Two-plate technology – hydraulic clamping force Fast tool movement due to two diagonal cylinders Tool protection function Linear guide for BWAP (MAIII PLUS, MA-F) Set of spray nozzles Closing and opening of the mold (max. 5 stages, min. 3 stages) Tool height limitation via limit sensor Clamping plates according to Euromap standard Ejector reset function Display of ejector p ...

Clamping Force: 100 Ton Holding force: 110 Ton Maximum opening stroke: 380 mm Minimum mould height: 200 mm Maximum mould height: 430 mm Distance between plates: 610 mm Plate size: 600×600 mm Distance between columns: 420×420 mm Maximum weight supported: 700 kg Extraction stroke: 100 mm MORETTO receiver-hopper NOT included. WITTMANN granulate dispenser NOT included. SESOTEC metal detector NOT included. Screw diameter: between 25 and 35 mm - not accurately detected. Warning: the information reported has been taken from the manual and may not correspond to actual performance. For further information, on-site inspection is suggested. Approximate body dimensions: 4800×1900×2600 mm. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-45448-699

Holmloos, hole centering ring fixed plate Diameter 160 mm, minimum installation height 350 mm, maximum opening (hydraulic) 950 mm, core pull 1, equipped with hydraulic screw drive, documentation available, Please note! pick up by appointment, Fanuc robots not included Auction-ID: A1-43992-21

Distance between the clamps 470x470 mm, hole centering ring fixed plate Diameter 125 mm, minimum installation height 250 mm, maximum opening 900 mm, core pull 1, documentation, equipped with hydraulic screw drive, documentation, Attention! Pick up by appointment Auction-ID: A1-43992-18

Distance between the holms 1120x1010 mm, hole centering ring fixed plate Diameter 250 mm, minimum installation height 450 mm, maximum open travel 1400 mm, maximum opening (hydraulic) 2600 mm, core pull 4, Machine was dismantled in 2014, overhauled (Italy) and recommissioned, equipped with hydraulic screw drive, 189 Kw, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-3

Distance between the holms 920x760 mm, hole centering ring fixed plate Diameter 160 mm, minimum installation height 250 mm, maximum open travel 1000 mm, maximum opening (hydraulic) 1900 mm, core pull 4, Machine was dismantled in 2017, overhauled (Italy) and recommissioned, equipped with hydraulic screw drive, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-4

steel; connection diameter approx. 90 mm; filling opening approximately 700 mm; equipped with sight glass; total height approx. 760 mm; on 2 pallets without pallets; Auction-ID: A1-43992-212

Distance between the bars 710x630 mm, hole centering ring fixed plate Diameter 160 mm, minimum installation height 250 mm, maximum open travel 1450 mm, core pull 2, documentation, Machine was dismantled in 2014, overhauled (Italy) and recommissioned, equipped with hydraulic screw drive, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-11

Clamping Force: 100 Ton Holding force: 110 Ton Maximum opening stroke: 380 mm Minimum mould height: 200 mm Maximum mould height: 430 mm Distance between plates: 610 mm Plate size: 600×600 mm Distance between columns: 420×420 mm Maximum weight supported: 700 kg Extraction stroke: 100 mm WEMO manipulator NOT included. MORETTO receiver-hopper NOT included. WITTMANN granulate dispenser NOT included. SESOTEC metal detector NOT included. Screw diameter: between 25 and 35 mm - not accurately detected. Warning: the information reported has been taken from the manual and may not correspond to actual performance. For further information, on-site inspection is suggested. Approximate body dimensions: 4800 × 1900 × 2600 mm. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-4544 ...

Distance between the clamps 860x760 mm, hole centering ring fixed plate Diameter 160 mm, minimum installation height 900 mm, maximum open travel 1000 mm, maximum opening (hydraulic) 1900 mm, core pull 4, Machine was dismantled in 2014, overhauled (Italy) and recommissioned, equipped with hydraulic screw drive, 159 Kw, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-2

Holmloos, hole centering ring fixed plate Diameter 160 mm, minimum installation height 350 mm, maximum opening (hydraulic) 950 mm, core pull 1, equipped with hydraulic screw drive, documentation available, Please note! pick up by appointment, Fanuc robots not included Auction-ID: A1-43992-22

Distance between the bars 420x420 mm, hole centering ring fixed plate Diameter 125 mm, minimum installation height 250 mm, maximum opening 750 mm, core pull 1, documentation, equipped with hydraulic screw drive, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-19

Clamping Force: 160 Ton Maximum opening stroke: 450 mm Mould height: between 250 and 550 mm Distance between plates: 1000 mm Plate dimensions: 795x795 mm Distance between columns approx.: 520 x 520 mm Maximum weight supported: 1110 kg on the moving plate. Extraction stroke: 200 mm MORETTO Receiver-Hopper NOT included. With WEMO manipulator With SESOTEC metal detector Screw diameter: between 25 and 35 mm - not accurately detected Warning: the information reported has been taken from the manual and may not correspond to actual performance. For further information, on-site inspection is suggested. Approximate dimensions of the machine body: 5700×1600×3500 mm. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-45448-697

Distance between the strands 1120x1000 mm, hole centering ring fixed plate Diameter 160/200/250 mm, minimum installation height 200 mm, maximum open travel 1400 mm, core pull 2, equipped with electric screw drive, 272 Kw, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-5

Distance between the bars 1200x1010 mm, hole centering ring fixed plate Diameter 250 mm, minimum installation height 450 mm, maximum open travel 1400 mm, maximum opening (hydraulic) 2700 mm, core pull 4, equipped with hydraulic screw drive, 249 Kw, documentation, Machine was disassembled, overhauled (Italy) and recommissioned in 2014, Please note! Pick up by appointment Auction-ID: A1-43992-1

Distance between the bars 420x420 mm, hole centering ring fixed plate Diameter 125 mm, minimum installation height 250 mm, maximum opening 750 mm, core pull 1, documentation, equipped with hydraulic screw drive, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-17

Distance between the bars 420x420 mm, hole centering ring fixed plate Diameter 125 mm, minimum installation height 250 mm, maximum opening 750 mm, core pull 1, documentation, equipped with hydraulic screw drive, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-20

Key data: 11500 , 6500 , 120

Presse à injecter BILLION 1150 T Type : H10140/1150? Epaisseur min /max moule : 400/1600 mm ?Dimensions des plateaux : 1770 x 1770 mm ?Distance entre colonnes : 1170 x 1170 mm? Course d'éjection : 400 mm? Diamètre vis : 120 mm? Pression max sur matière : 1495 bars? Pression hydraulique maxi : 160 bars? Course ouverture maxi : 1650 mm? Volume maxi injectable : 6766 cm3 ?Longueur vis L/D : 28 ?Capacité maxi injection : 160 mm/s

HAITIAN ZHAFIR 230 T Hybrid Injection Molding Machine Type: ZE 2300-830 Closing Force: 2300 kN / 230 T Year: 2015 Screw Diameter: 50 mm Injection Volume: 421 cm³ Injection Pressure: 2000 bar L/D Ratio: 25 Distance Between Tie bar : 620 mm x 620 mm Opening Stroke: 550 mm Mold Thickness (min/max): 220/600 mm Motor Power: 151 kW

Mastermatic System for Plastic Injection Machines Type: Control and regulation system for injection moulding machines Manufacturer: Mastermatic Operating pressure: Between 50 bar and 200 bar Functionality not tested This item is delivered loaded on truck. Dismantling and loading costs are specified as additional costs. Auction-ID: A1-45225-57

Year of construction : 2011 Control CC200 Locking force 400 tons incl. various accessories ( Piovan cooling unit, Tooltemp cooling unit, vacuum pump ) Machine comes directly from production

- Battenfeld TM3500 / 1900 BJ 2002 or 2001 control B4 without robot for sale. - The machine is currently running in production, no defects.

A large-format horizontal injection molding machine Battenfeld is available. Operating pressure: 210bar, clamping force: 4500kN, screw diameter: 85mm, injection volume: 2128cm³, injection pressure: 1624bar, tie-bar spacing: 900mm/800mm, opening stroke: 950mm, max. mold installation height: 970mm, oil volume: 900l, connected load: 55kW, weight: approx. 20400kg. Documentation available. An on-site inspection is possible. The machine has a defect.

Sandretto Nove HP 100 Injection Moulding Machine + Chiller & Hoist Overview Excellent opportunity to acquire a complete plastic injection moulding cell. This lot features the reliable Sandretto Nove HP 100 industrial injection moulding machine, capable of processing a wide variety of polymers (PP, PE, ABS, PS, PA, PC). To provide a complete turnkey solution for your manufacturing floor, the sale also includes the original Sandretto Nove chiller (cooling unit) and a Sandretto Otto 150 hoist. Clamping Unit Specifications Clamping Force: ~100 Tons (≈ 980 kN) Tie-Bar Clearance: ~410 mm (16.14") Maximum Mould Opening: ~460 mm Minimum Mould Thickness: ~100 mm Clamping Type: Hydraulic 4-tie-bar system Injection Unit Specifications Screw Diameter: Variable (approx. 30–45 mm depending on version) L/D Ratio: ~18:1 to 22:1 Injection Pressure: Up to ~1500–2000 ...

KraussMaffei 50-160 C1 Injection Moulding Machine Type: Injection moulding machine Manufacturer: KraussMaffei Model: 50-160 C1 Year of manufacture: 1996 Serial number: 44461 Screw diameter: ~25 mm (some units have 30 mm variants) Injection volume: 101 cm³ Injection pressure: 1488 bar Closing force: 500 kN Mould opening stroke: 350 mm: 200 mm – 550 mm Electric connection: 400 V Machine weight: 2300 kg Total dimensions (L x W x H): 3191 x 1500 x 1887 mm Clamping plate size: 540 x 540 mm Tie-bar spacing (H x V): approx. 321 x 321 mm Mould height (min/max): approx. 200/550 mm Shot volume: approx. 52 cm³ (standard) Shot weight: approx. 47 g (PS equivalent) Injection weight: 92 g Functionality not tested This item is delivered loaded on truck. Dismantling and loading costs are specified as additional costs. Auction-ID: A1-45225-3

KraussMaffei 50-190 C1 Injection Moulding Machine Type: Injection moulding machine Manufacturer: KraussMaffei Model: 50-190 C1 Year of manufacture: 1994 Serial number: 44236 Screw diameter: 30 mm Closing force: 500 kN Mould opening stroke: 350 mm Ejector stroke: 100 mm Injection pressure bar: 2222 Ejector force: 22 kN Electric connection: 400 V Approx. machine weight: 2300 kg Approx total dimensions (L x W x H): 3191 x 1500 x 1887 mm Tie bar spacing (H x V): approx. 321 x 321 mm Mould height range (min-max): ~200 mm - 550 mm Max. shot weight: ~66 g PS (polystyrene equivalent) Platen size: ~540 mm × 540 mm Functionality not tested This item is delivered loaded on truck. Dismantling and loading costs are specified as additional costs. Auction-ID: A1-45225-8

Injection moulding machine ARBURG 820 S 4000-2100 with Multilift Select (2016)

Key data: 1000 kN

ARBURG ALLROUNDER SELECTA 470 S 1000 – 675 (Year 2001) Serial number: 187132 – Machine 8 Clamping force: 1000 kN Distance between tie bars: 470 x 470 mm Platen size: 637 x 637 mm Max. mould height: 750 mm Ejector force: 40 kN Ejector stroke: 175 mm Shot volume: 675 cm³ Operating voltage: 400 V – 3 Ph – 50 Hz Heating capacity: 14.9 kW Pump motor: 1 x 22.00 kW Total connected load: 36.9 kW Dimensions: 4180 x 1645 x h, 2140 mm. Machine weight: 5400 kg

Key data: 500 kN

ARBURG ALLROUNDER CENTEX 320 C 500 – 250 (Year 2002) Serial number: 188161 – Machine no. 30 Clamping force: 500 kN Distance between tie bars: 320 x 320 mm Platen dimensions: 446 x 446 mm Injection unit (EUROMAP): 250 Approx. shot volume: 106 cm³ Shot weight (PS): 97 g Operating voltage: 400 V – 3 Ph – 50 Hz Heating capacity: 6.5 kW Pump motor: 1 x 15.00 kW Total connected load: 21.5 kW Machine weight: 2330 kg

Clamping force: 1000 kN. Distance between tie bars: 470 x 470 mm. Platen size: 637 x 637 mm. Max. mould height: 750 mm. Ejector force: 40 kN. Ejector stroke: 175 mm. Shot volume: 675 cm³. Operating voltage: 400 V – 3 Ph – 50 Hz. Heating capacity: 14.9 kW. Pump motor: 1 x 22.00 kW. Total connected load: 36.9 kW Dimensions: 4180 x 1645 x h. 2140 mm. Machine weight: 5400 kg. Serial number: 187133 – Machine 9

Injection Mold Type: Plastic injection mold Year of build: 2022 Mold Features High durability tool steel construction Reinforced cavity design for large part molding Multi-point injection to ensure uniform filling Optimized cooling system to reduce cycle time Robust ejection system for large plastic parts Designed for high-volume industrial production Functionality not tested This item is delivered loaded on truck. Dismantling and loading costs are specified as additional costs. Auction-ID: A1-45225-71

This 3-axis DEMAG ERGOTECH 1500-840 was manufactured in 1999. It features a clamping force of 1500 kN and a screw diameter of 45 mm, making it suitable for processing various materials such as PA, PP, PE, and ABS. The machine has a maximum pressure of 190 bar and a stroke volume of 358 cm³. If you are looking to get high-quality injection moulding capabilities, consider the DEMAG ERGOTECH 1500-840 hydraulic injection moulding machine we have for sale. Contact us for further details.

This DEMAG SYSTEC 80/420-310 was manufactured in 2008. It features a clamping force of 800 kN and a screw diameter of 35 mm, making it suitable for processing various materials such as PA, PP, PE, and ABS. The machine includes a Wittmann linear robot and a Gravimax 14R gravimetric blender. If you are looking to get high-quality injection moulding capabilities, consider the DEMAG SYSTEC 80/420-310 hydraulic injection moulding machine we have for sale. Contact us for further details.

B&A REF:  9307 TON: 1100 SCREW DIAMETER:  105MM SHOT WEIGHT: 3075 STROKE VOLUME:  3380CM3 INJECTION PRESSURE: 1600AR PLATEN SIZES:  1850 X 1810MM DBTB: 1400 X 1150MM MIN MOULD HEIGHT:  600MM MAX MOULD HEIGHT: 1200MM MOULD OPENING STROKE:  1800MM MAX DAYLIGHT:  2400MM EJECTOR STROKE:  300MM CONTROLS: CC 200 TOUCH CORE PULLING: 4 AIR VALVES: 2 MOTOR: 75 HEATING CAPACITY: 72KW ROBOT INTERFACE: EUROMAP 67 SCREW DRIVE:   HYDRAULIC