127,580 used machines on RESALE, but how to find them? Machine Search
Clamping force 135 t, toggle clamping system with 4 tie bars, tie-bar spacing 400 × 400 mm, mold height 150–500 mm, opening stroke 400 mm, ejector stroke 150 mm, screw diameters 45/50/55 mm, injection volume 286–427 cm³, injection pressure 1210–1800 bar, 4 heating zones, installed power 31 kW, overall dimensions approx. 4,900 × 1,200 × 2,050 mm, weight approx. 5,000–5,700 kg. Machine No. 959.
Two injection molding machines are offered, year of manufacture 2008 and 2009. Clamping force: 500kN, tie bar spacing X/Y: 320mm/320mm, mold mounting plates X/Y: 446mm/446mm, opening stroke: 350mm, max. platen distance: 550mm, injection unit 170: screw diameter: 25mm-30mm, shot volume: approx. 59ccm/25mm screw, approx. 85ccm/30mm screw, shot weight: approx. 62g to 77g, injection pressure: up to 2500bar. Inspection is possible by arrangement.
used
Some older plastic injection molding machines from Arburg, Demag and Stübbe are available. 1) Stübbe S110/345, year of manufacture: 1976, clamping force: 1000kN, shot weight: 140g, mold installation height min./max.: 180mm/480mm, opening stroke: 320mm, tie bar spacing: 360mm/355mm, screw diameter: 40mm, core pulls: 1. 2) Demag D 150-452 NC III, year of manufacture: 1990, clamping force: 1500kN, shot weight: 207g, mold installation height min./max.: 320mm/550mm, opening stroke: 430mm, tie bar spacing: 460mm/460mm, screw diameter: 45mm, core pulls: 1. 3) Demag D 100-275 NC II P, year of manufacture: 1989, clamping force: 1000kN, shot weight: 130g, mold installation height min./max.: 200mm/400mm, opening stroke: 350mm, tie bar spacing: 400mm/400mm, screw diameter: 38mm, core pulls: 1. 4) Arburg Allrounder 270M 250-75, year of manufacture: 1990, clamping force: 250kN, shot weight: 25g, mol ...
3 x Injection moulding machines Stork 440 to 1 x Injection moulding machine Stork 660 to 2 x Injection moulding machine Stork 900 to
Key data: 1500 kN, 40 mm
ARBURG ALLROUNDER 520 H 1500-400 (2015) Injection molding machine + WITTMANN ROBOT + Conveyor belt In operation Hours: 68946 h. Clamping force: 1500 kN Clamping unit 520 H Opening force / stroke: 450 mm. Fixed / variable mould mounting height: 250-550 mm. Fixed / variable platen spacing: 700-1000 mm. Column spacing: 520 x 520 mm Mold clamping platens (width x height) 695 x 695 mm. Weight of movable mould half: 1000 kg max. Force – Ejector stroke: 40 kN – 175 mm Idle cycle time: Conformt Min 1.5 – s- 364 Screw diameter: 40 mm. Effective screw length: 20 L/D Screw stroke: 160 mm. Calculated injection volume: 201 cm3 Weight per injection: 184 g. Ps. Material flow rate: 29 kg/h. PS Injection pressure: 2000 s-bar Post-pressure time: 45-2000 s-bar Injection flow: 214 cm3/s Injection speed: 170 mm/s Power – heating zones: 9.7 kW – 5 Oil capacity: 160 l. Weight ...
Key data: 3000 kN, 679 g/PS, 60 mm
1.0 St. gebr. Injection Molding Machine Manufacturer: KRAUSS MAFFEI Type: KM300-1900C2 Year of Make: 2005 Clamping force: 300 tons Spar spacing 630 x 630 mm Screws DN: 60 mm Max. displacement: 754 cm³ Moulded part weight: 679 g/hp Control: MC5 Equipment: 2 pcs core train Interface Robot Cavity pressure measurement 24-fold hot zone channel control Interface temperature control unit Approx. 76,000 operating hours
Key data: 3000 kN
1.0 St. gebr. Injection Molding Machine Manufacturer: KRAUSS MAFFEI Type: KM300-1900CX Year of Make: 2011 Clamping force: 300 tons Spar spacing 630 x 630 mm Screws DN: 60 mm Maximum displacement: 769 cm³ Moulded part weight: 692 g/hp Control: MC6 Equipment: 3 pcs. core train Interface Robot 45-fold hot zone channel control Interface temperature control unit Approx. 51,000 operating hours
Key data: 5000 kN, 2 g/PS, 90 mm
1.0 St. gebr. Injection Molding Machine Manufacturer: KRAUSS MAFFEI Type: KM300-1900CX Year of Make: 2011 Clamping force: 300 tons Spar spacing 630 x 630 mm Screws DN: 60 mm Maximum displacement: 769 cm³ Moulded part weight: 692 g/hp Control: MC6 Equipment: 3 pcs. core train Djbr Rvoxyrc Isf Nysul Interface Robot 45-fold hot zone channel control Interface temperature control unit Approx. 51,000 operating hours
Key data: 2500 kN, 579 g/PS, 60 mm
1.0 St. gebr. Injection Molding Machine with Robot Manufacturer: DEMAG Type: ET250-840 Concept Year of Make: 2004 Clamping force: 250 tons Spar spacing 630 x 630 mm Screws DN: 60 mm Max. displacement: 636 cm³ Moulded part weight: 579 g/hp Control: NC5 Equipment: Robot manufacturer: WITTMANN, type: W633-931 2 pcs core train
Key data: 2000 kN, 352 g/PS, 50 mm
1.0 St. gebr. Two-component injection molding machine with robot Manufacturer: ENGEL Type: ES650H/200W-200HL-2F Year of Make: 2000 Clamping force: 200 tons Tiebar spacing sparless Min. installation height: 450 mm Opening travel: 700 mm Screws DN 1: 50 mm Max. displacement: 392 cm³ Moulded part weight in hp: 352 g Screw DN 2: 25 mm Max. displacement: 69 cm³ Moulded part weight in hp: 60 g Control: CC200 Technical equipment: -Engel robot, type: ERC23/1-E -4 core slides -Turntable control
Key data: 2000 kN, 216 g/PS, 40 mm
1.0 St. gebr. Two-component injection molding machine with robot Manufacturer: ENGEL Type: ES650H/200W-200HL-2F Year of Make: 2001 Clamping force: 200 tons Tiebar spacing sparless Min. installation height: 550 mm Opening travel: 700 mm Screws DN 1: 40 mm Max. displacement: 251 cm³ Moulded part weight in hp: 216 g Screw DN 2: 25 mm Max. displacement: 69 cm³ Moulded part weight in hp: 60 g Control: CC200 Technical equipment: -Engel robot, type: ERC23/1-E -4 core slides -Turntable control
Key data: 2000 kN, 216 g/PS, 40 mm
1.0 St. gebr. Two-component injection molding machine with robot Manufacturer: ENGEL Type: ES650H/200W-200HL-2F Year of Make: 2004 Clamping force: 200 tons Tiebar spacing sparless Min. installation height: 500 mm Opening travel: 750 mm Screws DN 1: 40 mm Max. displacement: 251 cm³ Moulded part weight in hp: 216 g Screw DN 2: 25 mm Max. displacement: 69 cm³ Moulded part weight in hp: 60 g Control: CC200 Technical equipment: -Engel robot, type: ERC23/1-E -4 core slides -Turntable control
Key data: 600 kN, 94 g/PS, 30 mm
1.0 St. gebr. Injection Molding Machine with Robot Manufacturer: DEMAG Type: ET60-200 Concept Year of Make: 2003 Clamping force: 60 tons Spar spacing 420 x 420 mm Screws DN: 30 mm Max. displacement: 106 cm³ Moulded part weight: 94 g/hp Control: NC5 Equipment: Robot manufacturer: WITTMANN, type: W621-1381 2 pcs core train
Spritzgießmaschine HUARONG HRN-400 wurde 2008 in Taiwan von HUARONG PLASTIC MACHINERY CO., LTD. gebaut. Die Maschine wird für die wirtschaftliche Produktion von Kunststoffteilen in verschiedenen Farben, Formen und Größen eingesetzt. Diese Teile werden im Spritzgussverfahren hergestellt, bei dem plastifizierter Kunststoff in eine Form eingefüllt und dann mit hoher Presskraft gepresst wird. Um die höchste Produktivität und Wiederholbarkeit der hergestellten Teile zu erreichen, verfügt die Maschine über eine Reihe zuverlässiger Lösungen. Dazu gehören unter anderem ein Präzisions-Formenspannsystem, das mit einer Kraft von 400 Tonnen arbeitet, und ein Potentiometer, das die Position der Formen genau erfasst. Die Verformung der Aufspannplatten hingegen wird durch speziell entwickelte Säulen minimiert. Ein Zentralschmiersystem schmiert kontinuierlich alle beweglichen Teile der ...
Key data: 4200 kN, 2 g/PS, 80 mm
1.0 St. gebr. Injection Molding Machine Manufacturer: KRAUSS MAFFEI Type: KM420-4300CX Year of Make: 2012 Clamping force: 420 tons Spar spacing 800 x 800 mm Screws DN: 80 mm Max. displacement: 1,810 cm³ Moulded part weight: 1,647 g/hp Control: MC6 Equipment: 2 pcs core train Interface Robot 12-way hot zone channel control Interface temperature control unit
Key data: 2500 kN, 476 g/PS, 55 mm
1.0 St. gebr. Injection Molding Machine Manufacturer: KRAUSS MAFFEI Type: KM250-1000CX Year of Make: 2017 Clamping force: 250 tons Spar spacing 630 x 630 mm Screws DN: 55 mm Max. displacement: 523 cm³ Moulded part weight: 476 g/hp Control: MC6 Equipment: 2 pcs core train Interface Robot 12-way hot zone channel control Interface temperature control unit
B&A REF: 9170 TON: 50 SCREW DIAMETER: 14MM SHOT WEIGHT: 1 STROKE VOLUME: 1.1CM3 INJECTION PRESSURE: 2500AR PLATEN SIZES: 364 X 196MM MIN MOULD HEIGHT: 100MM MOULD OPENING STROKE: 200MM MAX DAYLIGHT: 300MM EJECTOR STROKE: 50MM CONTROLS: UNILOG B4
An Arburg injection molding machine with a rotary unit on the moving mold half is available. Column spacing: 420mm, clamping force: 1000kN, opening force: 250kN, opening stroke: 500mm, min. mold installation height: 250mm, platen dimensions X/Y: 570mm/570mm, max. mold weight: 600kg, ejector stroke: 175mm. Injection unit 350, screw diameter: 35mm/40mm/45mm, max. shot volume: 230cm³, max. injection pressure: 2500bar. Machine dimensions X/Y/Z: approx. 4300mm/1700mm/2750mm, weight: approx. 4500kg, operating hours: approx. 75443h. Documentation available. On-site inspection is possible.
2 Babyplast-machines for sale. Injection capacity 9 cm3. One is year 2009, one is year 2011
B&A REF: 9127 TON: 80 SCREW DIAMETER: 40MM SHOT WEIGHT: 183 STROKE VOLUME: 201CM3 INJECTION PRESSURE: 1860AR PLATEN SIZES: 670 X 670MM DBTB: 420 X 420MM MIN MOULD HEIGHT: 250MM MOULD OPENING STROKE: 500MM MAX DAYLIGHT: 750MM EJECTOR STROKE: 150MM CONTROLS: MC5 CORE PULLING: 2 AIR VALVES: 2 MOTOR: 15 HEATING CAPACITY: 10.97KW SCREW DRIVE: HYDRAULIC
A fully equipped Arburg injection molding machine including clean air supply Filter Fan Unit and removal robot is available. Clamping force: 1600kN, screw diameter: 45mm, max. cylinder heating: 450°C, total connected load: 85.5kW, machine elevation: 100mm, operating hours: approx. 9171h. Arburg Multilift H: axis: B, Z-axis stroke: 1400mm, conveyor belt length: 2500mm, conveyor belt width: 600mm, deposit height range: 900mm-1300mm, temperature resistance: 160°C. Documentation available. An on-site inspection is possible.
A fully equipped Arburg injection molding machine including clean air supply Filter Fan Unit and removal robot is available. Clamping force: 1600kN, screw diameter: 45mm, max. cylinder heating: 450°C, total connected load: 85.5kW, machine elevation: 100mm, operating hours: approx. 13361h. Arburg Multilift H: axis: B, Z-axis stroke: 1400mm, conveyor belt length: 2500mm, conveyor belt width: 600mm, deposit height range: 900mm-1300mm, temperature resistance: 160°C. Documentation available. An on-site inspection is possible.
B&A REF: 9024 TON: 160 SCREW DIAMETER: 50MM SHOT WEIGHT: 343 STROKE VOLUME: 377CM3 INJECTION PRESSURE: 1892AR PLATEN SIZES: 710 X 660MM DBTB: 520 X 470MM MIN MOULD HEIGHT: 200MM MAX MOULD HEIGHT: 500MM MOULD OPENING STROKE: 450MM MAX DAYLIGHT: 950MM EJECTOR STROKE: 150MM CONTROLS: MC6 CORE PULLING: 2 AIR VALVES: 2 HEATING CAPACITY: 17.7KW ROBOT INTERFACE: EUROMAP 67 ROBOT: GIEGER TECNOMATIC SCREW DRIVE: ELECTRIC HOT RUNNER: 12 ZONE
Key data: 2000 kN, 291 g/PS, 45 mm
1.0 St. gebr. Rotary Table Injection Molding Machine Manufacturer: ARBURG Type: 1500T2000-800 Year of Make: 2012 Clamping force: 200 tons Rotary table; 2 x 180° Screws DN: 45 mm Max. displacement: 313 cm³ Moulded part weight: 291 g/hp Control: SELGOCIA Equipment: 1 x Core Pulls
Key data: 3300 kN, 62 mm
Stork S+3300-2150 Year of Make: 2008 Clamping force: 330 tons Screw diameter: 62 mm Max. opening distance: 620 mm Injection pressure: 2100 bar Material: PP
A vertical injection molding machine Arburg with a horizontal injection unit is available. Clamping force: 800kN, opening stroke: 500mm, min. mold installation height: 250mm, platen spacing: 750mm, tie bar spacing X/Y: 420mm/420mm, platen dimensions X/Y: 570mm/570mm, max. mold weight: 600kg, ejector stroke: 175mm. Machine dimensions X/Y/Z: approx. 4350mm/1700mm/2100mm, weight: approx. 3500kg. Documentation available. On site inspection is possible.
Injection moulding machine Battenfeld Machine Type TM 2700/2800 Control Type B2 Year of construction 2003/04 Screw diameter 75 mm
A vertical injection molding machine Arburg with a horizontal injection unit is available. Clamping force: 1300kN, opening stroke: 500mm, min. mold installation height: 250mm, mounting plate distance: 750mm, tie bar spacing X/Y: 420mm/420mm, platen dimensions X/Y: 605mm/605mm, max. mold weight: 650kg, ejector stroke: 175mm. Machine dimensions X/Y/Z: approx. 4350mm/1650mm/2100mm, weight: approx. 4300kg, operating hours: approx. 80131h. Documentation available. On-site inspection is possible.
A vertical injection molding machine Arburg with a horizontal injection unit is available. Clamping force: 800kN, opening stroke: 500mm, min. mold installation height: 250mm, platen distance: 750mm, platen dimensions X/Y: 570mm/570mm, max. mold weight: 600kg. Machine dimensions X/Y/Z: approx. 4300mm/1700mm/2100mm, weight: approx. 3500kg, operating hours: 44117h. Documentation available. On-site inspection is possible.
Injection moulding machine Krauss Maffei KM 800-5700 BJ 1999 Technical data on request
Key data: 1500 kN, 45 mm
Stork S+S1500-850 Year of Make: 2011 Clamping force: 150 tons. Screw diameter: 45 mm Max opening distance: 480 mm Injection pressure: 2100 bar used for PP thin-wall packaging
Injection molding machine Krauss Maffei CX 650-3000 BJ 2009
Screw diameter: 120 mm Injectable volume / Shot volume: 5598 cm3 Injection pressure : 1137 bar Column passage / Bettween tie bar: 1060 x 1060 mm Mould thickness mini-maxi / Mould tickness mini-max: 350 - 1100 mm Opening stroke: 1150 mm Euromap 12 4 Hydraulic Cores / 4 Corepulling
This MAPLAN MFT 750/160 edition S was manufactured in 2016. It is a vertical injection moulding machine, ideal for precision plastic processing. Contact us for more information.
Screw diameter: 70 mm Injectable volume Shot volume: 5598 cm3 Injection pressure : 1137 bar Column pass-through: 1060 x 1060 mm Moulded thickness / Mold tickness mini -max: 350 - 1100 mm Opening stroke: 1150 mm Euromap 12 4 hydraulic cores - 4 cOREPULLING
This Arburg Allrounder 630S 2500-675 was manufactured in 2003. It is a hydraulic injection moulding machine featuring a screw diameter of 45mm. Consider the opportunity to buy this Arburg Allrounder 630S 2500-675 hydraulic injection moulding machine. Contact us for more information.
Screw diameter: 45 mm Injectable volume / Shot volume: 358 cm3 Injection Pressure: 2426 bar Column passage / Bettween tie bar: 720 x 720 mm Thickness of the mould mini /Mold tickness -max: 320 - 725 mm Opening stroke: 730 mm Euromap 12 4 hydraulic cores - 4 corepulling
This FANUC Roboshot S50iA was manufactured in 2016. It is an electrical injection moulding machine with a closing force of 50 tons and a screw diameter of 20mm. Consider the opportunity to buy this FANUC Roboshot S50iA electrical injection moulding machine. Contact us for more information.
This DEMAG Ergotech System 420-1450 was manufactured in 2004. It is a hydraulic injection moulding machine, ideal for precision plastic processing. Consider the opportunity to buy this DEMAG Ergotech System 420-1450 hydraulic injection moulding machine. Contact us for more information.
This Engel Insert 90 was manufactured in 2016. A vertical injection moulding machine with a total run time of only 54 hours and a weight of 9,500 KG. Consider the opportunity to buy this Engel Insert 90 vertical injection moulding machine. Contact us for more information.
This SUMITOMO SHI DEMAG Systec SP 350/720-840 was manufactured in 2015. It is a hydraulic injection moulding machine, ideal for precision plastic processing. Consider the opportunity to buy this SUMITOMO SHI DEMAG Systec SP 350/720-840 hydraulic injection moulding machine. Contact us for more information.
This Engel Insert 80V/40 was manufactured in 2011. A vertical injection moulding machine, its ideal for precision thermoplastic parts. Consider the opportunity to buy this Engel Insert 80V/40 vertical injection moulding machine. Contact us for more information.
This Netstal Elion 800-270 was manufactured in 2021. It features a robust AXOS control system and a high-speed injection unit capable of 450 mm/s. The machine includes a screw diameter of 40 mm and a fully integrated 9 kW hydraulic unit. It supports a tool installation height range of 200â500 mm and is equipped with a Euromap 67 robot interface. If you are looking to get high-quality injection molding capabilities, consider the Netstal Elion 800-270 machine we have for sale. Contact us for more information.
This Kloeckner Desma PU D522/12-LDI was manufactured in 2017. Designed for PU injection and shoe production, featuring a 12-station setup with a clamping force of 70 kN. It includes a reaction injection molding unit, automatic mold slider, and motor capacity of 23.16 kW. Heating capacity stands at 45.50 kW. Contact us for more information about this machine.
This DEMAG Ergotech System 200-610 hydraulic injection moulding machine was manufactured in 1997. Its a robust option for efficient plastic processing tasks. Contact us for more information.
This Arburg ALLROUNDER 1200 t 1000 - 400 Injection moulding machine was manufactured in the year 2018 in Germany. It has 58 production hours. The machine has a clamping force of 1000 kN, machine like new, used only for testing. Machine needs to be CE certified by the customer, we have a quote from a third party starting at 2.000â¬.
This DEMAG Ergotech Compact 125-440 hydraulic injection moulding machine was manufactured in 1998. Contact us for more information.
This OiMA SACMI 3300-180 was manufactured in 2009. It features a robust electric-hydraulic hybrid drive and an integrated cooling system. The machine is equipped with a GDNet communication interface for real-time monitoring and diagnostics, ideal for producing medium-to-large plastic components. Consider the opportunity to buy this OiMA SACMI 3300-180 hydraulic injection moulding machine. Contact us for more information.
This Battenfeld VM 150/750V R1520 UNIGLOG B6S was manufactured in 2011. It is a hydraulic injection moulding machine, ideal for precision plastic processing. Consider the opportunity to buy this Battenfeld VM 150/750V R1520 UNIGLOG B6S. Contact us for more information.
maximum number of results exceeded
please refine your search
