injection moulding for used for sale

Clamping force: 700kN, Opening stroke: 305mm, Ejector stroke: 105mm, Ejector force: 20kN, Screw diameter: 30mm, Shot volume: 99cm³, Speed: 480rpm, Injection pressure: 1451bar, Weight: approx. 6200kg, Control system: CC200, Operating hours: 57077h. Documentation available. An on-site inspection is possible.

Product material: LSR, ejector stroke: 150mm, operating pressure: 250bar, clamping force: 750kN, min. tool installation height: 250mm, opening stroke: 375mm, tie bar spacing X/Y: 320mm/320mm, max. platen dimensions X/Y: 490mm/490mm, max. injection volume: 187.5cm³, injection force: 145kN, max. injection pressure: 1150bar, screw diameter: 40mm. Machine dimensions X/Y/Z: approx. 4000mm/1850mm/2000mm, weight: approx. 3100kg. An on-site inspection is possible.

Clamping force: 1800 KN Max injection cc 500g 380V/50Hz Auction-ID: A7-45261-4

Clamping Force: 100 Ton Holding force: 110 Ton Maximum opening stroke: 380 mm Minimum mould height: 200 mm Maximum mould height: 430 mm Distance between plates: 610 mm Plate size: 600×600 mm Distance between columns: 420×420 mm Maximum weight supported: 700 kg Extraction stroke: 100 mm MORETTO receiver-hopper NOT included. WITTMANN granulate dispenser NOT included. SESOTEC metal detector NOT included. Screw diameter: between 25 and 35 mm - not accurately detected. Warning: the information reported has been taken from the manual and may not correspond to actual performance. For further information, on-site inspection is suggested. Approximate body dimensions: 4800×1900×2600 mm. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-45448-699

Distance between the clamps 470x470 mm, hole centering ring fixed plate Diameter 125 mm, minimum installation height 250 mm, maximum opening 900 mm, core pull 1, documentation, equipped with hydraulic screw drive, documentation, Attention! Pick up by appointment Auction-ID: A1-43992-18

Clamping Force: 100 Ton Holding force: 110 Ton Maximum opening stroke: 380 mm Minimum mould height: 200 mm Maximum mould height: 430 mm Distance between plates: 610 mm Plate size: 600×600 mm Distance between columns: 420×420 mm Maximum weight supported: 700 kg Extraction stroke: 100 mm WEMO manipulator NOT included. MORETTO receiver-hopper NOT included. WITTMANN granulate dispenser NOT included. SESOTEC metal detector NOT included. Screw diameter: between 25 and 35 mm - not accurately detected. Warning: the information reported has been taken from the manual and may not correspond to actual performance. For further information, on-site inspection is suggested. Approximate body dimensions: 4800 × 1900 × 2600 mm. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-4544 ...

Clamping Force: 160 Ton Maximum opening stroke: 450 mm Mould height: between 250 and 550 mm Distance between plates: 1000 mm Plate dimensions: 795x795 mm Distance between columns approx.: 520 x 520 mm Maximum weight supported: 1110 kg on the moving plate. Extraction stroke: 200 mm MORETTO Receiver-Hopper NOT included. With WEMO manipulator With SESOTEC metal detector Screw diameter: between 25 and 35 mm - not accurately detected Warning: the information reported has been taken from the manual and may not correspond to actual performance. For further information, on-site inspection is suggested. Approximate dimensions of the machine body: 5700×1600×3500 mm. The item is sold in the state in which it is, unverified and without warranty of operation. Item not subject to sales restrictions. Auction-ID: A7-45448-697

Distance between the bars 420x420 mm, hole centering ring fixed plate Diameter 125 mm, minimum installation height 250 mm, maximum opening 750 mm, core pull 1, documentation, equipped with hydraulic screw drive, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-19

Distance between the bars 420x420 mm, hole centering ring fixed plate Diameter 125 mm, minimum installation height 250 mm, maximum opening 750 mm, core pull 1, documentation, equipped with hydraulic screw drive, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-17

Distance between the bars 420x420 mm, hole centering ring fixed plate Diameter 125 mm, minimum installation height 250 mm, maximum opening 750 mm, core pull 1, documentation, equipped with hydraulic screw drive, documentation, Please note! Pick up by appointment Auction-ID: A1-43992-20

A large-format horizontal injection molding machine Battenfeld is available. Operating pressure: 210bar, clamping force: 4500kN, screw diameter: 85mm, injection volume: 2128cm³, injection pressure: 1624bar, tie-bar spacing: 900mm/800mm, opening stroke: 950mm, max. mold installation height: 970mm, oil volume: 900l, connected load: 55kW, weight: approx. 20400kg. Documentation available. An on-site inspection is possible. The machine has a defect.

KraussMaffei 50-160 C1 Injection Moulding Machine Type: Injection moulding machine Manufacturer: KraussMaffei Model: 50-160 C1 Year of manufacture: 1996 Serial number: 44461 Screw diameter: ~25 mm (some units have 30 mm variants) Injection volume: 101 cm³ Injection pressure: 1488 bar Closing force: 500 kN Mould opening stroke: 350 mm: 200 mm – 550 mm Electric connection: 400 V Machine weight: 2300 kg Total dimensions (L x W x H): 3191 x 1500 x 1887 mm Clamping plate size: 540 x 540 mm Tie-bar spacing (H x V): approx. 321 x 321 mm Mould height (min/max): approx. 200/550 mm Shot volume: approx. 52 cm³ (standard) Shot weight: approx. 47 g (PS equivalent) Injection weight: 92 g Functionality not tested This item is delivered loaded on truck. Dismantling and loading costs are specified as additional costs. Auction-ID: A1-45225-3

KraussMaffei 50-190 C1 Injection Moulding Machine Type: Injection moulding machine Manufacturer: KraussMaffei Model: 50-190 C1 Year of manufacture: 1994 Serial number: 44236 Screw diameter: 30 mm Closing force: 500 kN Mould opening stroke: 350 mm Ejector stroke: 100 mm Injection pressure bar: 2222 Ejector force: 22 kN Electric connection: 400 V Approx. machine weight: 2300 kg Approx total dimensions (L x W x H): 3191 x 1500 x 1887 mm Tie bar spacing (H x V): approx. 321 x 321 mm Mould height range (min-max): ~200 mm - 550 mm Max. shot weight: ~66 g PS (polystyrene equivalent) Platen size: ~540 mm × 540 mm Functionality not tested This item is delivered loaded on truck. Dismantling and loading costs are specified as additional costs. Auction-ID: A1-45225-8

Clamping force: 1000 kN. Distance between tie bars: 470 x 470 mm. Platen size: 637 x 637 mm. Max. mould height: 750 mm. Ejector force: 40 kN. Ejector stroke: 175 mm. Shot volume: 675 cm³. Operating voltage: 400 V – 3 Ph – 50 Hz. Heating capacity: 14.9 kW. Pump motor: 1 x 22.00 kW. Total connected load: 36.9 kW Dimensions: 4180 x 1645 x h. 2140 mm. Machine weight: 5400 kg. Serial number: 187133 – Machine 9

Clamping force: 200 Ton; piston closure; column passage: 520x520 mm; screw: 55mm; selogic control; Nr. 1 hydraulic jacks; Nr. 1 bellows; Euromap 12. Serial: 178453 Estimated weight: 6700 kg Approximate dimensions: 5500x2000xh2200 mm Auction-ID: A7-44996-25

Clamping force: 430 Ton; toggle closure; column passage: 760x680 mm; screw: 60mm; control B&R Columbia; Nr. 2 pneumatic jacks and 2 hydraulic jacks; Nr. 1 air blow; Euromap 12. Serial: 364-112 Estimated weight: 19500 kg Approximate dimensions: 8200x1950xh2600 mm Auction-ID: A7-44996-26

This 3-axis DEMAG ERGOTECH 1500-840 was manufactured in 1999. It features a clamping force of 1500 kN and a screw diameter of 45 mm, making it suitable for processing various materials such as PA, PP, PE, and ABS. The machine has a maximum pressure of 190 bar and a stroke volume of 358 cm³. If you are looking to get high-quality injection moulding capabilities, consider the DEMAG ERGOTECH 1500-840 hydraulic injection moulding machine we have for sale. Contact us for further details.

This DEMAG SYSTEC 80/420-310 was manufactured in 2008. It features a clamping force of 800 kN and a screw diameter of 35 mm, making it suitable for processing various materials such as PA, PP, PE, and ABS. The machine includes a Wittmann linear robot and a Gravimax 14R gravimetric blender. If you are looking to get high-quality injection moulding capabilities, consider the DEMAG SYSTEC 80/420-310 hydraulic injection moulding machine we have for sale. Contact us for further details.

This 6-axis Arburg Allrounder 520 S 1600-290 / 290 was manufactured in 2015. It features a highly wear-resistant thermoplastic cylinder with a 30 mm diameter and a drive unit powered by a 30 kW motor. The machine is equipped with advanced control systems for both injection units and supports multi-component processing. If you are looking to get high-quality injection moulding capabilities, consider the Arburg Allrounder 520 S 1600-290 / 290 hydraulic injection moulding machine we have for sale. Contact us for further details.

This 6-axis Krauss Maffei 1000-8000 M hydraulic injection moulding machine was manufactured in 1997. It features a maximum X-axis travel of 1000 mm, Y-axis travel of 1400 mm, and Z-axis travel of 3500 mm. The machine includes an injection pressure limit of 185 bar and a metering stroke of approximately 465 mm. If you are looking to get high-quality injection moulding capabilities, consider the Krauss Maffei 1000-8000 M machine we have for sale. Contact us for further details.

This Krauss Maffei KM 800-6100MX was manufactured in 2007. It features a clamping force of 8000 kN and an injection volume of 2695 cm³, making it suitable for various materials such as PA, PP, PE, and ABS. The machine is equipped with a Wittmann Robot System for enhanced handling capabilities. If you are looking to get high-quality injection moulding capabilities, consider the Krauss Maffei KM 800-6100MX hydraulic injection moulding machine we have for sale. Contact us for further details.

Hydraulic injection moulding machine manufactured in 2019. This Engel Victory 120 BMG features a clamping force of 120 t and a tie-bar-less design, ensuring efficient operation. It includes a high-speed injection unit and an advanced CC300 control system with a 21.5 full HD touchscreen. If you are looking to get high-quality injection moulding capabilities, consider the Engel Victory 120 BMG machine we have for sale. Contact us for further details regarding this machine.

LPG forklift, gas forklift STILL type RX 70-16TSeries No. 517314G00021 Year of construction 2016Nominal load capacity 1600 kgLifting height 4920 mmFork length 1000 mmCarriage width 980 mmOverall height 2160 mmTotal width 1100 mmTotal length without forks 2200 mmNet weight 3040 kg- Triplex mast with full free lift 1550 mm- Hydraulic sideshift- LPG electric drive- 4-cylinder Volkswagen LPG engine with 30 kW- Hydraulic auxiliary steering- Front working lights- Reversing Warning light (blue)

Electric forklift JUNGHEINRICH type EFG 216Serial No. FN413671 year of construction 2011Load capacity 1600 kgLifting height 4800 mmFork length 1220 mmFork carriage width 980 mmOverall height 2120 mmOperating voltage 48 volt- Triplex mast with full free lift 1550 mm- Hydraulic sideshifter- 2 travel speeds- Battery from year of construction 2015, Type 06 EPZS C750 SC (48 Volt, 750 Ah)- Automatic charger, 48 Volt- 3-wheel solid rubber - Front tires 18 x 7-8, rear 140/55-9- according to the operating hour meter 14725 operating hours read-

Diesel - Forklift, Compact Forklift MORA Type M80CSFabr. No. 20087 Year of construction 2006Nominal load capacity 8 ton. Lifting height 3800 mmFork length 1800 mmFork carriage width 1460 mmOverall height 3030 mmTotal width 1460 mmTotal length without forks 3350 mmWeight 12740 kg- Duplex mast with 1950 mm free lift- 4 cylinders PERKINS diesel engine- Fully enclosed cab with heating- Electro-hydraulic tilting device for the cab- Hydraulic auxiliary steering- 2 front work lights, 1 piece

Battery from former Still Service Comes from Still RX60-30 with only 3,700 hours of use. With REMA 320A connector and Aquamatic water filling 1030x700x780mm Voltage at rest measured uncharged with good power of 85.86 V Loading onto trucks with forklift trucks. Delivery by freight forwarder possible on request. Auction-ID: A1-45450-1013

Battery from former Linde Service 830x730x630mm Voltage in idle mode uncharged 52.33 V and thus still very good. Loading onto trucks with forklift trucks. Delivery by freight forwarder possible on request. Auction-ID: A1-45450-1162

Battery from former Still Service Comes from Still RX60-30 with only 5,300 operating hours. With REMA 320A connector and Aquamatic water filling 1030x700x780mm Idle voltage measured uncharged with good performance of 85.03 V Loading onto trucks with forklift trucks. Delivery by freight forwarder possible on request. Auction-ID: A1-45450-1050

Battery from former Linde service very good performance measured at 52.25V Loading onto trucks with forklift trucks. Delivery by freight forwarder possible on request. Auction-ID: A1-45450-1146

Battery from former Linde Service 830x730x630mm Voltage in idle mode uncharged 51.31 V and thus still very good. Loading onto trucks with forklift trucks. Delivery by freight forwarder possible on request. Auction-ID: A1-45450-1010

Battery from former Linde Service 830x730x630mm Voltage in idle mode uncharged 50.98 V and thus still very good. Loading onto trucks with forklift trucks. Delivery by freight forwarder possible on request. Auction-ID: A1-45450-1095

Battery from former Linde Service 1030x1000x800mm Voltage in idle mode uncharged 84.54 V and thus still very good. Loading onto trucks with forklift trucks. Delivery by freight forwarder possible on request. Auction-ID: A1-45450-1144

Battery from former Linde Service 1020x1000x800mm Voltage at rest uncharged measured with good performance of 83.39 V Loading onto trucks with forklift trucks. Delivery by freight forwarder possible on request. Auction-ID: A1-45450-1056

Charger 24V Ah with REMA battery plug and 220V Schuko wall plug Loading onto trucks no problem Auction-ID: A1-45450-3541

Battery from former Linde Service 830x730x630mm Voltage in idle mode uncharged 51.90 V and thus still very good. Loading onto trucks with forklift trucks. Delivery by freight forwarder possible on request. Auction-ID: A1-45450-1123

Battery from former Linde Service 830x730x630mm Voltage in idle mode uncharged 51.23 V and thus still very good. Loading onto trucks with forklift trucks. Delivery by freight forwarder possible on request. Auction-ID: A1-45450-1134

CAP.: 10 000 BTLS/H OF 1.5 L,

for the production of pillow candies Power 10 - 250 kg/h, depending on type and size of the candies

automatic CUTTING BORING and MOULDING machine BACCI TTF1 2TM . second hand machine working conditions : Excellent hydraulic drive of all the movements volt. 380/50 CE mark : YES Machine suitable for assembling part of chairs, tables, frames, furniture, wheelchair frames, etc. The BACCI TTF1 2TM performs the operations of cutting , milling and drilling at the end of the piece, either singularly or differently combined . the milling unit is composed of n.02 spindle moulders ( anti-splinter system ) machine composed by 3 working units : 1- Cutting unit : circular saw max.diam. mm.400 motor power Hp 3 2- Boring unit : boring head with 5 mandrins motor power Hp 3 3- Moulding unit . with automatic movement of the carriage on recirculating ball bearings n.02 spindle moulders (anti-splinter) motor power Hp 7,5 spindle diam. mm.35 hydraulic unit motor power Hp 2

Mouldingpresse The MP / 3E is a hydraulic press for the production of Clayprofilen such as rubber seals, protective, decorative or chrome strips. By inserting an appropriate form template in the bolt head, almost any profile can be produced up to a diameter of 65 mm. Manufacturer: Wadhwa Type: MP / 3 p Year of construction: 1995 Temperature controller Speed controller Via a rotary control a stepless adjustment of the speed is possible heated sealing head The built-in heater in the bolt head is adjustable Foot switch Weight: 125 kg Fully functional All information without guarantee Sold only to businesses

1 x Wickert 500ton upstroke vacuum press, Type: WKP5000/5/3, Year of manufacture: 1997, Machine Number: 2885 with 500mm x 500mm electrically heated platens, sliding bottom platen with ejector table, Daylight: 340mm 400/690V, 50Hz, 22kW. Heaters 12.5kW, Pressure 300 Bar Fixed guarding to rear, SICK light curtain guards to the front. With Siemens S5 PLC controls. In very good condition.

AUTOMATIC CUTTING , BORING and MOULDING machine type PADE 1000 N Machine suitable for assembling part of chairs, tables, frames, small furniture, wheelchair frames, etc. The PADE 1000 N performs the operations of Cutting , milling and drilling at the end of the piece, either singularly or differently combined. All movements of the machine are controlled by pneumatic devices. composed by 3 working units : 1- Cutting unit circular saw diam. mm.350 motor power hp 3 2- Boring unit boring head with 5 / 7 mandrins motor power Hp 3 max. working stroke of boring unit mm. 130 3- Moulding unit vertical spindle for moulder motor power Hp 5,5 spindle diam. mm.30 pneumatic sliding carriage volt. 380/50

The list of equipment for sale from molding line: 1. Moulding Machine HSP-2D (22kW, 70f / h) 2. Lifting table 3. Pressure plate 4. The dispensing sand tank

KALMEIJER Pastry moulding rolls (standard A,B + C rolls)for KGM Christmas motifs used, good condition, different motifs: Spekulatius sorted German males Skat Nikolaus with fir tree (special roller)

Manufacture | Manufacturer: Bekum Machine type | Machine type: BA15 Station | Stations: Single station | Single station Construction year | Year of construction: 2003 Location | Location: UES Clamping force | Clamping force: 170 kN Control system | Control type: Orig. Bekum Parison Control | WBK: 50 points | 50 points Extruder | Extruder: S 82/20D Parison Head | Hose head: Accu-head AKZ2.3 refurbished 2020 | Battery head AKZ2.3 overhauled in 2020 Mould Dimension | Shape dimensions mm (A length/B width/C depth): 525/400/2150 bottle volume | Bottle volume: 40 L Monitour language | Screen language: English | English Delivery time | Delivery time: Immediately | Right away

Flat 4-sided blade (package, 10 pcs.) 12x12x1,5 Flat 2-sided blade (package, 10 pcs.) 20x12x1,5 Flat 2-sided blade (package, 10 pcs.) 30x12x1,5 Flat 2-sided blade (package, 8 pcs.) (used) 50x12x1,5

Qty. 1 Second-hand pulp moulding plant Maker: DongJin MP Tech Model no.: DPF 70-85 S2 Built: 2007 Dry type pulp moulding machine Quantity: 4 units Condition: can be inspected in dry running Three step way: heating /pressing/vacuum dry -Platen size: 700 x 850 mm -Dimensions: 1300(W) x 3200 (L) x 4000(H) mm

Used blow moulding machine made by KRONES model Contiform S18. New 2004. It has 18 blow moulding stations. The maximum blow moulding speed is 24,000 bottles per hour for the 2.0 l format and 28,000 bottles per hour for the 1.5 l format. In February 2024, the machine was upgraded to support the PCO 2622 thread. The blow moulding machine has an integrated control system with visualisation in Polish, English and German. A complete set of documentation is included with the blow moulding machine. The blow moulding machine includes: an automatic glycol cooler, an automatic preform feeder, an automatic preform basket tipper and a bottle ejector mounted on an air transport conveyor.